Porter-Cable PCC607 Instruction Manual

20V Max* 1/2 inch (13mm) Brushless Drill / Driver

Perceuse visseuse sans balai de 13mm (1/2po) et 20V Max*

Taladro/atornillador sin escobillas de 20V Máx* de 1/2 pulg. (13 mm)

CATALOG NUMBER

N° DE CATALOGUE
CATÁLOGO N°

PCC607

Instruction manual
Manuel d’instructions
Manual de’instrucciones

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA:

LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

Thank you for choosing PORTER-CABLE! To register your new product, go to:

www.portercable.com/ServiceAndSupport/ProductRegistration.aspx

Merci d’avoir choisi PORTER-CABLE! Consulter le site Web www.portercable.com/
ServiceAndSupport/ProductRegistration.aspx pour enregistrer votre nouveau produit.

Gracias por elegir PORTER-CABLE usted! Para registrar su nuevo producto, visite: www.
portercable.com / ServiceAndSupport / ProductRegistration.aspx

*Maximum initial battery pack voltage (measured without a workload) is 20 volts.
Measured under a workload, nominal voltage is 18.
*La tension initiale maximale du bloc-piles (mesurée sans charge de travail) est de 20
volts. La tension nominale est de 18.
*El máximo voltaje inicial del paquete de baterías (medido sin una carga de trabajo)
es 20 voltios. la tensión nominal es de 18.

2

General Power Tool Safety
Warnings

WARNING: Read all safety warnings

and all instructions. Failure to follow the

warnings and instructions may result in
electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings
refers to your mains-operated
(corded) power tool or battery­operated (cordless) power tool.

1) WORK AREA SAFETY
a) Keep work area clean and well

lit. Cluttered or dark areas invite

accidents.

b) Do not operate power tools in

explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose
control.

2) ELECTRICAL SAFETY
a) Power tool plugs must match the

outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.

Unmodified plugs and matching outlets
will reduce risk of electric shock.

b) Avoid body contact with earthed

or grounded surfaces such as
pipes, radiators, ranges and
refrigerators. There is an increased

risk of electric shock if your body is
earthed or grounded.

c) Do not expose power tools to rain

or wet conditions. Water entering

a power tool will increase the risk of
electric shock.

d) Do not abuse the cord. Never use

the cord for carrying, pulling or
unplugging the power tool. Keep cord
away from heat, oil, sharp edges or
moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool

outdoors, use an extension cord
suitable for outdoor use. Use of a

cord suitable for outdoor use reduces
the risk of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a
ground fault circuit interrupter
(GFCI) protected supply. Use of a

GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY
a) Stay alert, watch what you are

doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.

A moment of inattention while
operating power tools may result in
serious personal injury.

b) Use personal protective equipment.

Always wear eye protection.

Protective equipment such as dust
mask, nonskid safety shoes, hard
hat, or hearing protection used for
appropriate conditions will reduce
personal injuries.

c) Prevent unintentional starting.

Ensure the switch is in the off
position before connecting to
power source and/ or battery pack,
picking up or carrying the tool.

Carrying power tools with your finger
on the switch or energizing power
tools that have the switch on invites
accidents.

d) Remove any adjusting key or

wrench before turning the power

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided,

may result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

3

tool on. A wrench or a key left

attached to a rotating part of the power
tool may result in personal injury.

e) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the
power tool in unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewelry. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,

jewelry or long hair can be caught in
moving parts.

g) If devices are provided for the

connection of dust extraction and
collection facilities, ensure these
are connected and properly used.

Use of dust collection can reduce
dust-related hazards.

4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use

the correct power tool for your
application. The correct power tool

will do the job better and safer at the
rate for which it was designed.

b) Do not use the power tool if the

switch does not turn it on and
off. Any power tool that cannot

be controlled with the switch is
dangerous and must be repaired.

c) Disconnect the plug from the

power source and/or the battery
pack from the power tool before
making any adjustments,
changing accessories, or storing
power tools. Such preventive safety

measures reduce the risk of starting
the power tool accidentally.

d) Store idle power tools out of

the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power

tools are dangerous in the hands of
untrained users.

e) Maintain power tools. Check

for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
If damaged, have the power
tool repaired before use. Many

accidents are caused by poorly
maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.

g) Use the power tool, accessories

and tool bits, etc. in accordance
with these instructions, taking into
account the working conditions

and the work to be performed.

Use of the power tool for operations
different from those intended could
result in a hazardous situation.

5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger

specified by the manufacturer. A

charger that is suitable for one type
of battery pack may create a risk of
fire when used with another battery
pack.

b) Use power tools only with

specifically designated battery
packs. Use of any other battery

packs may create a risk of injury and
fire.

c) When battery pack is not in use,

keep it away from other metal
objects like paper clips, coins, keys,
nails, screws, or other small metal
objects that can make a connection
from one terminal to another.

Shorting the battery terminals together
may cause burns or a fire.

d) Under abusive conditions,

liquid may be ejected from the
battery, avoid contact. If contact
accidentally occurs, flush with
water. If liquid contacts eyes,
additionally seek medical help.

Liquid ejected from the battery may
cause irritation or burns.

6) SERVICE
a) Have your power tool serviced by a

qualified repair person using only
identical replacement parts. This will

ensure that the safety of the power
tool is maintained.

Drill Safety Warnings

•

Wear ear protectors with impact drills.

Exposure to noise can cause hearing loss.

• Use auxiliary handle(s), if supplied

with the tool. Loss of control can cause
personal injury.

• Hold power tool by insulated gripping

surfaces, when performing an
operation where the cutting accessory
may contact hidden wiring. Cutting

accessory contacting a “live” wire may
make exposed metal parts of the power
tool “live” and could give the operator an
electric shock.

• Use clamps or another practical way

to secure and support the work piece
to a stable platform. Holding the work

by hand or against your body leaves it
unstable and may lead to loss of control.

• Do not operate this tool for long

periods of time. Vibration caused by the

operating action of this tool may cause
permanent injury to fingers, hands,

4

and arms. Use gloves to provide extra
cushion, take frequent rest periods, and
limit daily time of use.

• Keep your hair, clothing, and gloves
away from air vents. Air vents often

cover moving parts in which these items
can be caught.

• Hammer bits and tools get hot during
operation. Wear gloves when touching them.

•

Hold tool firmly with two hands, one
hand on the handle, and the other
gripping the bottom around the battery
area or the auxiliary handle if provided.
Loss of control can cause personal injury.

• When not in use, place tool on its side
on a stable surface where it will not
cause a tripping or falling hazard. Some

tools with large battery packs will stand
upright but may be easily knocked over.

• Wear safety goggles or other eye
protection. Hammering and drilling

operations cause chips to fly. Flying
particles can cause permanent eye
damage. Everyday eyeglasses are NOT
safety glasses. Also use face or dust
mask if drilling operation is dusty.

ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CPA
Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

WARNING: Some dust created by

power sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to the state
of California to cause cancer, birth
defects or other reproductive harm.

Some examples of these chemicals are:

•

lead from lead-based paints,

•

crystalline silica from bricks and cement

and other masonry products, and

•

arsenic and chromium from

chemically-treated lumber.

Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.

•

Avoid prolonged contact with
dust from power sanding, sawing,
grinding, drilling, and other
construction activities. Wear
protective clothing and wash exposed
areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay
on the skin may promote absorption of
harmful chemicals.

WARNING:

Use of this tool can
generate and/or disperse dust, which may
cause serious and permanent respiratory

or other injury. Always use NOSH/OSHA

approved respiratory protection appropriate
for the dust exposure. Direct particles away
from face and body.

SYMBOLS

The label on your tool may include the
following symbols. The symbols and their
definitions are as follows:

V ..................volts

A ..................amperes

Hz ................ hertz

W .................watts

min ..............minutes

or AC ...... alternating current

or DC ...direct current

n

o ................ no load speed

................Class I Construction

................earthing terminal

(grounded)

............... safety alert symbol

................Class II Construction

(double insulated)
.../min or rpm...revolutions or
reciprocation per minute

..............Read instruction manual

before use

................ Use proper respiratory

protection

...............Use proper eye protection

................ Use proper hearing

protection

BPM ...........beats per minute

IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This
manual contains important safety
instructions for battery chargers.

WARNING: Before using charger,

read all instructions and cautionary
markings on charger, battery pack, and
product using battery pack.

• Shock hazard. Do not allow any liquid

to get inside charger.

• Burn hazard. To reduce the risk

of injury, charge only designated
PORTER-CABLE batteries. Other types
of batteries may burst causing personal
injury and damage.

• Under certain conditions, with the

charger plugged in to the power
supply, the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil, or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.

• DO NOT attempt to charge the battery

5

pack with any chargers other than the
ones in this manual. The charger and

battery pack are specifically designed to
work together.

•

These chargers are not intended for any
uses other than charging designated
PORTER-CABLE rechargeable
batteries. Any other uses may result in

risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when

disconnecting charger. This will reduce
risk of damage to electric plug and cord.

• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.

• Do not use an extension cord
unless it is absolutely necessary.

Use of improper extension cord could
result in risk of fire, electric shock, or
electrocution.

• An extension cord must have
adequate wire size (AWG or American
Wire Gauge) for safety. The smaller

the gauge number of the wire, the
greater the capacity of the cable, that
is 16 gauge has more capacity than
18 gauge. When using more than one
extension to make up the total length, be
sure each individual extension contains
at least the minimum wire size.

• Do not place any object on top of
charger or place the charger on a soft
surface that might block the ventilation
slots and result in excessive internal
heat. Place the charger in a position
away from any heat source. The

charger is ventilated through slots in the

top and the bottom of the housing.

• Do not operate charger with damaged cord
or plug — have them replaced immediately.

• Do not operate charger if it has
received a sharp blow, been dropped,
or otherwise damaged in any way.

Take it to an authorized service center.

• Do not disassemble charger; take it
to an authorized service center when
service or repair is required. Incorrect
reassembly may result in a risk of
electric shock, electrocution or fire.

• Disconnect the charger from the
outlet before attempting any cleaning.

This will reduce the risk of electric shock.
Removing the battery pack will not

reduce this risk.

• NEVER attempt to connect 2 chargers
together.

• The charger is designed to operate on
standard household electrical power
(120 Volts). Do not attempt to use it on
any other voltage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY PACKS

WARNING:

For safe operation, read
this manual and manuals originally supplied
with tool before using the battery pack.

The battery pack is not fully charged out of
the carton. Before using the battery pack and
charger, read the safety instructions below.
Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack

even if it is severely damaged or is
completely worn out. The battery pack

can explode in a fire. Toxic fumes and
materials are created when Li-Ion battery
packs are burned.

•

Do not charge or use battery in explosive

atmospheres, such as in the presence
of flammable liquids, gases or dust.

Inserting or removing the battery from the
charger may ignite the dust or fumes.

•

If battery contents come into contact

with the skin, immediately wash area
with mild soap and water. If battery liquid

gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases.
If medical attention is needed, the battery
electrolyte for Li-Ion batteries is composed
of a mixture of liquid organic carbonates
and lithium salts.

• Contents of opened battery cells may

cause respiratory irritation. Provide

fresh air. If symptoms persists, seek
medical attention.

WARNING:

Burn hazard. Battery liquid

may be flammable if exposed to spark or flame.

• Charge the battery packs only in

PORTER-CABLE chargers.

• DO NOT splash or immerse in water

or other liquids. This may cause

premature cell failure.

• Do not store or use the tool and battery

pack in locations where the temperature
may be reach or exceed 105°F (40˚C)
(such as outside sheds or metal
buildings in summer).

WARNING:

Never attempt to open the

battery pack for any reason. If battery pack
case is cracked or damaged, do not insert
into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or
charger that has received a sharp blow,
been dropped, run over or damaged in any

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

Ampere Rating

More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

way (i.e., pierced with a nail, hit with a
hammer, stepped on). Damaged battery
packs should be returned to service center
for recycling.

WARNING:

Fire hazard. Do not

store or carry battery so that metal
objects can contact exposed battery
terminals. For example, do not place

battery in aprons, pockets, tool boxes,
product kit boxes, drawers, etc., with loose
nails, screws, keys, etc. Transporting

batteries can possibly cause fires if the
battery terminals inadvertently come in
contact with conductive materials such
as keys, coins, hand tools and the like.

The US Department of Transportation
Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in
commerce or on airplanes (i.e., packed in
suitcases and carry-on luggage) UNLESS
they are properly protected from short
circuits. So when transporting individual
batteries, make sure that the battery
terminals are protected and well insulated
from materials that could contact them and
cause a short circuit. NOTE: Li-Ion

batteries should not be put in checked
baggage.

NOTE: Do not store the battery packs in
a tool with the trigger switch locked on.
Never tape the trigger switch in the ON
position.

NEVER force the battery pack into the
charger. DO NOT modify the battery pack
in any way to fit into a non-compatible
charger as battery pack may rupture
causing serious personal injury.

Storage Recommendations

1. The best storage place is one that is
cool and dry away from direct sunlight
and excess heat or cold.

2. Long-term storage will not harm the
battery pack or the charger as long as the
battery is not depleted.

6

This product uses the batteries and chargers listed below.

20V Max* Lithium-Ion Batteries: PCC680L, PCC681L, PCC682/PCC682L, PCC685L
20V Max* Lithium-Ion Chargers: PCC690L, PCC691L, PCC692/PCC692L, PCC695L, PCC699L

FUNCTIONAL DESCRIPTION
Figure A

1. Trigger Switch

2. Forward/Reverse Button

3. Torque Adjust Collar

4. Mode Control Collar

5. Dual Range Gear Selector

6. Keyless Chuck

7. Battery

8. Battery Release Button

9. Battery Fuel Gauge

10. LED Work Light

11. Bit Tip Clip

2

1

3

6

7

9

8

5

4

11

10

Charging Procedure

PORTER-CABLE chargers are designed

to charge PORTER-CABLE battery
packs. Charge times are: PCC690L in
40-80 mins., PCC699L /PCC691L in
70-140 mins., PCC692/PCC692L in 40-80
mins., and PCC695L in 180-360 mins.
depending on the pack being charged.

1. Plug the charger into an appropriate
outlet before inserting the battery pack.

2. Insert the battery pack into the charger.

3. The LED will flash indicating that
the battery is being charged.

4. The completion of charge is indicated

by the LED remaining on continuously.
The pack is fully charged and may be used at
this time or left on the charger.

Recharge discharged batteries as soon
as possible after use or battery life
may be greatly diminished. For longest
battery life, do not discharge batteries
fully. It is recommended that the batteries

be recharged after each use.

Charger Diagnostics

This charger is designed to detect certain
problems that can arise with the battery packs
or the power source. Problems are indicated
by one LED flashing in different patterns.

Bad Battery

The charger can detect a weak or

damaged battery. The LED flashes in
the pattern indicated on the label. If you see
this bad battery blink pattern, do not continue
to charge the battery. Return it to a service
center or a collection site for recycling.

Hot/Cold Pack Delay

When the charger detects a battery

that is excessively hot or excessively
cold, it automatically starts a Hot/Cold
Pack Delay, suspending charging until the
battery has normalized. After this happens,
the charger automatically switches to the
Pack Charging mode. This feature ensures
maximum battery life. The light flashes in
the pattern indicated on the label.

Problem Power Line

When the charger is used with some

portable power sources such as
generators or sources that convert DC to
AC, the charger may temporarily suspend
operation. The LED flashes in the pattern
indicated on the label. This indicates that
the power source is out of limits.

Leaving the Battery in the Charger

The charger and battery pack can be
left connected with the LED glowing
indefinitely. The charger will keep the
battery pack fresh and fully charged.
This charger features an automatic tune-

up mode which equals or balances the
individual cells in the battery pack to allow
it to function at peak capacity. Battery
packs should be tuned up weekly or
whenever the battery no longer delivers the
same amount of work. To use the automatic
tune-up mode, place the battery pack in the
charger and leave it for at least 8 hours.

Important Charging Notes

1. Longest life and best performance can
be obtained if the battery pack is charged
when the air temperature is between 65°F
and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below
+40°F (+4.5°C), or above +105°F (+40.5°C).
This is important and will prevent serious
damage to the battery pack.

2. The charger and battery pack may
become warm to touch while charging.
This is a normal condition, and does
not indicate a problem. To facilitate the
cooling of the battery pack after use,
avoid placing the charger or battery pack
in a warm environment such as in a metal
shed, or an uninsulated trailer.

3. If the battery pack does not charge
properly:

a. Check current at receptacle by
plugging in a lamp or other appliance
b. Check to see if receptacle is
connected to a light switch which turns
power off when you turn out the lights.
c. Move charger and battery pack to a
location where the surrounding air
temperature is approximately 65°F ­75°F (18°- 24°C).
d. If charging problems persist, take
the tool, battery pack and charger to
your local service center.

4. The battery pack should be recharged
when it fails to produce sufficient power
on jobs which were easily done previously.
DO NOT CONTINUE to use under these
conditions. Follow the charging procedure.
You may also charge a partially used pack
whenever you desire with no adverse
affect on the battery pack.

SAFETY WARNINGS AND
INSTRUCTIONS: DRILLS

WARNING:

Before using tool, read all

instructions and cautionary markings on tool.

WARNING:

Drill may stall (if

overloaded or improperly used) causing a
twist. Always expect the stall. Grip the drill
firmly with two hands to control the twisting
action and prevent loss of control which
could cause personal injury. If a stall does
occur, release the trigger immediately and
determine the reason for the stall before
re-starting.

7

Intended Use

This drill driver is designed for drilling and screw
driving applications.

DO NOT use under wet conditions or in the
presence of flammable liquids or gases.

DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.

NEVER modify the power tool or any part of it.
Damage or personal injury could result.

Operating Instructions

Installing and Removing the
Battery Pack From the Tool

WARNING:

To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making
any adjustments or removing/installing
attachments or accessories. An accidental

start-up can cause injury.

CAUTION: Make certain the lock-off

button is engaged to prevent switch
actuation before removing or installing
battery.

TO INSTALL BATTERY PACK: Insert
battery pack (7) firmly into tool until an
audible click is heard as shown in Figure
B. Ensure battery pack is fully seated and
fully latched into position.

TO REMOVE BATTERY PACK: Depress
the battery release button (8) as shown in

Figure C and pull battery pack out of tool.

Variable Speed Trigger Switch

The tool is turned ON and OFF by
squeezing and releasing the trigger switch
(1). The farther the trigger is depressed,
the higher the speed of the drill.

• To turn the tool on, squeeze the trigger
switch (1).

• To turn the tool off, release the trigger
switch. Your tool is equipped with a
brake. The chuck will stop as soon as
the trigger switch is fully released.

NOTE:

Continuous use in variable
speed range is not recommended. It
may damage the switch and should be
avoided.

Forward/Reverse Button

A forward/reverse control button (2)
determines the rotational direction of the
tool and also serves as a lock off button.

• To select forward rotation, release the

trigger switch and depress the forward/
reverse control button on the right side
of the tool.

• To select reverse, depress the forward/

reverse control button on the left side of
the tool.

• The center position of the control button

locks the tool in the off position. When
changing the position of the control
button, be sure the trigger is released.

Mode Control Collar - Figure D

Your drill is equipped with a separate mode
control collar (4) to switch between screw
driving and drilling mode.

Adjusting Torque Control

This tool is fitted with a torque adjustment
collar (4) to select the operating mode
and to set the torque for tightening
screws. Large screws and hard workpiece
materials require a higher torque setting
than small screws and soft workpiece
materials.

• For drilling in wood, metal and plastics,

set the collar to the drilling position
symbol

• For screw driving, set the collar to the

desired setting. If you do not yet know
the appropriate setting, proceed as
follows:

• Set the collar to the lowest torque setting.

8

D

C

B

• Tighten the first screw.

• If the clutch ratchets before the desired
result is achieved, increase the collar
setting and continue tightening the
screw. Repeat until you reach the correct
setting. Use this setting for the remaining
screws.

Dual Range Gearing

The dual range feature of your drill allows
you to shift gears for greater versatility.

• To select low speed, high torque setting
(position 1), turn tool off and permit to
stop. Slide dual range gear selector (5)
away from the chuck.

• To select the high speed, low torque
setting (position 2), turn tool off and
permit to stop.

Slide gear shifter button

back toward the chuck.

NOTE: Do not change gears when tool is
running. If you are having trouble changing
gears, make sure that the dual range gear
button is either completely pushed forward
or completely pushed back.

Keyless Chuck

WARNING: Make certain the battery

pack is removed to prevent tool actuation
before installing or removing accessories.

To insert a drill bit or other accessory:

1. Grasp the chuck (6) and rotate it in

the counterclockwise direction, as
viewed from the chuck end.

2. I

nsert the bit or other accessory fully
into the chuck, and tighten securely
by rotating the chuck in the clockwise
direction as viewed from the chuck end.

WARNING: Do not attempt to tighten

or loosen drill bits (or any other accessory)
by gripping the front part of the chuck and
turning the tool on. Damage to the chuck
and personal injury may occur when
changing accessories.

Drilling

WARNING:

Drill may stall if

overloaded causing a sudden twist.

Always expect the stall. Grip the drill firmly
to control the twisting action and avoid
injury.

(Shift drill into DRILL mode)

• Use sharp drill bits only.

• Support and secure work properly, as
instructed in the Safety Instructions.

• Use appropriate and required safety
equipment, as instructed in the Safety
Instructions.

• Secure and maintain work area, as
instructed in the Safety Instructions.

• Run the drill very slowly, using light
pressure, until the hole is started enough
to keep the drill bit from slipping out of it.

• Apply pressure in a straight line with the

9

bit. Use enough pressure to keep the
bit biting but not so much as to stall the
motor or deflect the bit.

• Hold the drill firmly with two hands,
one hand on the handle, and the other
gripping the bottom around the battery
area or the auxiliary handle if provided.

• DO NOT CLICK THE TRIGGER OF A
STALLED DRILL OFF AND ON IN AN
ATTEMPT TO START IT. DAMAGE TO
THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by
reducing pressure and slowly drilling
through the last part of the hole.

• Keep the motor running while pulling
the bit out of a drilled hole. This will help
reduce jamming.

• Make sure switch turns drill on and off.

Drilling in Wood

Holes in wood can be made with the
same twist drill bits used for metal or with
spade bits. These bits should be sharp
and should be pulled out frequently when
drilling to clear chips from the flutes.

Drilling in Metal

Use a cutting lubricant when drilling
metals. The exceptions are cast iron
and brass which should be drilled dry.
The cutting lubricants that work best are
sulfurized cutting oil or lard oil.

Screw Driving

WARNING:

Always ensure the bit is

secure before starting the tool. A loose bit

may eject from tool causing possible
personal injury.

(Shift drill into SCREW mode)

• For driving fasteners, the forward/reverse
button should be pushed to the left.

• Use reverse (button pushed to the right)
for removing fasteners.

NOTE: When moving from forward to
reverse, or vice versa, always release the
trigger switch first.

Battery Fuel Gauge - Figure E

The tool is equipped with a battery fuel
gauge (9).

This can be used to display the current
level of charge in the battery during
use and during charging. It does not
indicate tool functionality and is subject to
variation based on product components,
temperature and end-user application.

Checking battery charge during use:

• Press and hold the battery fuel gauge
button (E1).

• The three LEDs (E2) will illuminate
indicating the percent of charge in the
battery (Figure E).

• If LED light does not lluminate, charge
battery.

10

Troubleshooting

Problem Possible Cause Possible Solution

• Unit will not start. • Battery pack not installed properly. • Check battery pack
installation.

• Battery pack not charged. • Check battery pack
charging requirements.

• Internal components too hot. • Allow tool to cool down.

•

Battery pack will not charge.

•

Battery pack not inserted into charger.

• Insert battery pack into
charger until LED
lights.

• Charger not plugged in. • Plug charger into a
working outlet. Refer to
“Important Charging Notes”
for more details.

• Surrounding air temperature • Move charger and battery
too hot or too cold. pack to a surrounding air
temperature of above 40
degrees F (4,5°C) or below
105 degrees F (+40,5°C).

• Unit shuts off abruptly. • Battery pack has reached its • Allow battery pack to cool

maximum thermal limit. down.

• Out of charge. ( To • Place on charger and

maximize the life of the allow to charge.
battery pack it is designed
to shutoff abruptly when
the charge is depleted.)

For assistance with your product, visit our website at www.portercable.com for a list of
service centers, or call the PORTER-CABLE Customer Care Center at [phone].

NOTE: This battery is designed to not
operate when a charge below 20% of
its capacity is reached. After the battery
charge is depleted, the tool will not operate
until after the battery has been recharged.

LED Work Light - Figure E

There is a work light (10) located near
the battery fuel gauge (9). The work light
is activated when the trigger switch is
depressed, and will automatically turn
off 20 seconds after the trigger switch
is released. If the trigger switch remains
depressed, the work light will remain on.

NOTE: The work light is for lighting
the immediate work surface and is not
intended to be used as a flashlight.

Accessories Storage

• A bit storage slot (11) is built into the
base of the tool.

E

E2

E1

10

11

The RBRC® Seal

The RBRC® (Rechargeable
Battery Recycling Corp oration)
Seal on the nickel cadmium,
nickel metal hydride or lithium­ion batteries (or battery packs) indicates
that the costs to recycle these batteries
(or battery packs) at the end of their useful
life have already been paid by PORTER­CABLE. In some areas, it is illegal to
place spent nickel cadmium, nickel metal
hydride or lithium-ion batteries in the trash
or municipal solid waste stream and the
Call 2 Recycle® program provides an
environmentally conscious alternative.
Call 2 Recycle, Inc., in cooperation
with PORTER-CABLE and other battery
users, has established the program in the
United States and Canada to facilitate the
collection of spent nickel cadmium, nickel
metal hydride or lithium-ion batteries. Help
protect our environment and conserve
natural resources by returning the spent
nickel cadmium, nickel metal hydride
or lithium-ion batteries to an authorized
PORTER-CABLE service center or to your
local retailer for recycling. You may also
contact your local recycling center for
information on where to drop off the spent
battery. RBRC® is a registered trademark
of Call 2 Recycle, Inc.

MAINTENANCE

WARNING:

To reduce the risk of
serious personal injury, turn tool off and
remove the battery pack before making any
adjustments or removing/installing
attachments or accessories. An accidental
start-up can cause injury.

CLEANING

WARNING:

Blow dirt and dust out of
all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury,
always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING:

Never use solvents or
other harsh chemicals for cleaning the non­metallic parts of the tool. These chemicals
may weaken the plastic materials used in
these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get
inside the tool; never immerse any part of
the tool into a liquid.

Use only mild soap and damp cloth to
clean the tool. Never let any liquid get
inside the tool; never immerse any part of
the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING:

Shock hazard. Disconnect
the charger from the AC outlet before
cleaning.

Dirt and grease may be removed from the
exterior of the charger using a cloth or soft
non-metallic brush. Do not use water or
any cleaning solutions.

REPLACEMENT PARTS

Use only identical replacement parts. For a
parts list or to order parts, visit our service
website at www.portercable.com. You can also
order parts from your nearest PORTER-CABLE
Factory Service Center or PORTER-CABLE
Authorized Warranty Service Center. Or, you
can call our Customer Care Center at
[phone].

This Class B digital apparatus complies
with Canadian ICES-003.

This device complies with part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference,
and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.

NOTE: This equipment has been tested
and found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference in
a residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation.

If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

Changes or modifications to this unit

purchase.
90 DAY MONEY BACK GUARANTEE: If
you are not completely satisfied with the
performance of your PORTER-CABLE
Power Tool for any reason, you can return
it within 90 days from the date of purchase
with a receipt for a full refund – no questions
asked.
LATIN AMERICA: This warranty does not
apply to products sold in Latin America.
For products sold in Latin America, see
country specific warranty information
contained in the packaging, call the local
company or see website for warranty
information.
To register your tool for warranty service
visit our website at www.portercable.com.

WARNING LABEL REPLACEMENT

If your warning labels become illegible
or are missing, call [phone] for a
free replacement.

4825 Highway 45 North

Jackson, Tennessee 38305

[phone]

www.portercable.com

12

not expressly approved by the party
responsible for compliance could void the
user’s authority to operate the equipment.
This Class B digital apparatus complies
with Canadian ICES-003.

SERVICE AND REPAIRS

All quality tools will eventually require servicing
and/or replacement of parts. For information about
PORTER-CABLE, its factory service centers or
authorized warranty service centers, visit our website
at www.portercable.com or call our Customer Care
Center at [phone]. All repairs made by our
service centers are fully guaranteed against defective
material and workmanship. We cannot guarantee
repairs made or attempted by others. You can also
write to us for information at PORTER-CABLE, 4825
Highway 45 North, Jackson, Tennessee 38305, (888)
848-5175 - Attention: Product Service. Be sure to
include all of the information shown on the nameplate
of your tool (model number, type, serial number, etc.).

ACCESSORIES

WARNING: Since accessories, other

than those offered by PORTER-CABLE,
have not been tested with this product,
use of such accessories with this tool
could be hazardous. To reduce the risk of
injury, only PORTER-CABLE
recommended accessories should be
used with this product.
A complete line of accessories is
available from your PORTER-CABLE
Factory Service Center or a PORTER­CABLE Authorized Warranty Service
Center. Please visit our Web Site www.
portercable.com for a catalog or for the
name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace,
without charge, any defects due to faulty
materials or workmanship for three years
from the date of purchase for tools (two
years for batteries). This warranty does
not cover part failure due to normal
wear or tool abuse. For further detail of
warranty coverage and warranty repair
information, visit www.portercable.com
or call [phone]. This warranty
does not apply to accessories or damage
caused where repairs have been made or
attempted by others. This warranty gives
you specific legal rights and you may
have other rights which vary in certain
states or provinces.
In addition to the warranty, PORTER­CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER­CABLE will maintain the tool and replace
worn parts caused by normal use, for
free, any time during the first year after