Porter-Cable PCB330BS Instruction Manual

14 IN. (355 MM) BAND SAW SCIE À RUBAN 355 MM (14 PO)

SIERRA DE CINTA PA

BRANCO DE 355 MM (14 PULG.)

Instruction Manual

Manuel d’instructions Manual de instrucciones

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA

: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

CATALOG NUMBER

PCB330BS

TABLE OF CONTENTS

SECTION PAGE

PRODUCT SPECIFICATION

CALIFORNIA PROPOSITION 65 ............................................................................................................................. 2

SAFETY GUIDELINES - DEFINITIONS ................................................................................................................... 3

POWER TOOL SAFETY

BAND SAW SAFETY ................................................................................................................................................

ELECTRICAL REQUIREMENTS AND SAFETY TOOLS NEEDED FOR ASSEMBLY

CARTON CONTENTS ..............................................................................................................................................

KNOW YOUR GLOSSARY OF TERMS

ASSEMBLY AND ADJUSTMENTS............................................................................................................................ 11

OPERATION .............................................................................................................................................................

MAINTENANCE ....................................................................................................................................................... 21

TROUBLESHOOTING GUIDE.................................................................................................................................. 22

ACCESSORIES AND ATTACHMENTS PARTS LIST WARRANTY

BAND SAW........................................................................................................................................ 9

............................................................................................................................................................. 25

............................................................................................................................................................. 28

S ................................................................................................................................. 2

........................................................................................................................................... 4

...................................................................................................... 6

......................................................................................................................... 7

........................................................................................................................................... 10

.................................................................................................................... 24

PRODUCT SPECIFICATIONS

MOTOR BLADE

Amps ............. 10 / 5 AMP Width ................ 1/8, 1/4, 3/8, 1/2 in.

Voltage .......... 120 / 240 V (3.2, 6.4, 9.5, 12.7 mm)

Hz .................. 60 Length .............. 93-1/2 in. (2374.9 mm)

Horsepower ... 1.5 HP (Max. Developed) CUTTING CAPACITY

Speed ............ 1630/2730 Feet per minute (No load) Throat................. 13-5/8 in. (346 mm)

Type................ Induction Height................. 6 in. (152.4 mm)

DRIVE BELT A-26 SAWDUST PORT 2-1/2 in. O.D. (63.5 mm) TABLE SIZE 16 x 16 in. (406.4 x 406.4 mm)

WARNING

To avoid electrical hazards, ﬁre hazards or damage to the tool, use proper circuit protection. Use a separate electrical circuit for your tools. This band saw is wired at the factory for 110-120/220-240 Volt operation. It must be connected to a 110-120 Volt / 10 Ampere or 220-240 Volt / 5 Ampere time delay fuse or circuit breaker. To avoid shock or ﬁre, replace power cord immediately if it is worn, cut or damaged in any way.

CALIFORNIA PROPOSITION 65

WARNING

Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to ﬁlter out microscopic particles. Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

WARNING

appropriate for the dust exposure. Direct particles away from face and body.

2009/09

Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

Printed in Taiwan

SAFETY GUIDELINES - DEFINITIONS

WARNING ICONS Your power tool and its Instruction Manual may contain “WARNING ICONS” (a picture symbol intended to alert you to, and/or instruct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate your tool better and safer. Shown below are some of the symbols you may see.

SAFETY ALERT:

PROHIBITION

WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with side shields.

READ AND UNDERSTAND INSTRUCTION MANUAL: To reduce the risk of injury, user and all bystanders

must read and understand instruction manual before using this product.

KEEP HANDS AWAY FROM BLADE: Failure to keep your hands away from the blade will result in serious personal injury.

SUPPORT AND CLAMP WORK

Precautions that involve your safety.

DANGER

WARNING

CAUTION

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

death or serious injury.

CAUTION

or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

: Indicates a potentially hazardous situation which, if not avoided, could result in

: Indicates a potentially hazardous situation which, if not avoided, may result in minor

POWER TOOL SAFETY

GENERAL SAFETY INSTRUCTIONS BEFORE USING THIS POWER TOOL

Safety is a combination of common sense, staying alert and knowing how to use your power tool.

WARNING

To avoid mistakes that could cause serious injury, do not plug the tool in until you have read and understood the following.

1. READ and become familiar with the entire

Instruction Manual. LEARN the tool’s application, limitations and possible hazards.

2. KEEP GUARDS IN PLACE and in working order.

3. REMOVE ADJUSTING KEYS AND WRENCHES.

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning ON.

4. KEEP WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

5. DO NOT USE IN DANGEROUS ENVIRONMENTS.

Do not use power tools in damp locations, or expose them to rain or snow. Keep work area well lit.

6. KEEP CHILDREN AWAY. All visitors and bystanders

should be kept a safe distance from work area.

7. MAKE WORKSHOP CHILD PROOF with padlocks,

master switches or by removing starter keys.

8. DO NOT FORCE THE TOOL. It will do the job better

and safer at the rate for which it was designed.

9. USE THE RIGHT TOOL. Do not force the tool or an

attachment to do a job for which it was not designed.

10. USE PROPER EXTENSION CORDS. Make sure

your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will result in a drop in line voltage and in loss of power which will cause the tool to overheat. The table on page 6 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

11. WEAR PROPER APPAREL

clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair.

. Do not wear loose

ANSI Z87.1 could seriously injure you when they break.

13. WEAR A FACE MASK OR DUST MASK. Sawing

operation produces dust.

14. SECURE WORK. Use clamps or a vise to

hold work when practical. It is safer than using your hand and it frees both hands to operate the tool.

15. DISCONNECT TOOLS FROM POWER SOURCE

before servicing, and when changing accessories such as blades, bits and cutters.

16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in the OFF position before plugging the tool in.

17. USE RECOMMENDED ACCESSORIES. Consult this Instruction Manual for recommended accessories. The use of improper accessories may cause risk of injury to yourself or others.

18. NEVER STAND ON THE TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

19. CHECK FOR DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

20. NEVER LEAVE THE TOOL RUNNING UNATTENDED. TURN THE POWER “OFF”. Do not walk away from a running tool until the blade comes to a complete stop and the tool is unplugged from the power source.

21. DO NOT OVERREACH. Keep proper footing and balance at all times.

22. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

23. DO NOT use power tool in presence of ﬂammable liquids or gases.

24. DO NOT operate the tool if you are under the inﬂuence of any drugs, alcohol or medicationn that could affect your ability to use the tool properly.

12. ALWAYS WEAR EYE PROTECTION. Any

power tool can throw foreign objects into the eyes and could cause permanent eye damage. ALWAYS wear Safety Goggles

(not glasses) that comply with ANSI Safety standard Z87.1. Everyday eyeglasses have only impact– resistant lenses. They ARE NOT safety glasses. NOTE: Glasses or goggles not in compliance with

25. Dust generated from certain materials can be hazardous to your health. Always operate saw in well-ventilated area and provide for proper dust removal.

26. WEAR HEARING PROTECTION to reduce the risk of induced hearing loss.

BAND SAW SAFETY

1. TO AVOID INJURY from unexpected movement,

make sure the saw is on a ﬁrm, level surface and properly secured to prevent rocking. Make sure there is adequate space for operating. Bolt the saw to a support surface to prevent slipping, walking or sliding during operation.

2. UNPLUG AND TURN the saw off before moving it.

3. USE THE CORRECT size and style of blade.

4. USE blades rated at 2700 FPM or greater.

5. MAKE SURE the blade teeth point down and

towards the table when installed on unit.

6. BLADE GUIDES, SUPPORT BEARINGS AND BLADE TENSION must be properly adjusted to avoid accidental blade contact and to minimize blade breakage. To maximize blade support, always adjust the upper blade guide and blade guard so that it is 1/8 inch (3.2 mm) above the workpiece.

7. TABLE LOCK HANDLE should be tight.

8. USE EXTRA CAUTION with large, very small or awkward workpieces.

16. TO FREE any jammed material, turn the switch off.

Remove the switch key and unplug the saw.

Wait for all moving parts to stop before removing

jammed material.

17. DO NOT LEAVE the work area until all moving parts

are stopped. To childproof the workshop, shut off power to master switches and remove the switch key from the band saw. Store it in a safe place, away from children.

WARNING

For your own safety, read the entire Instruction Manual before using the band saw.

1. Wear eye protection.

2. Do not wear gloves, neckties or loose clothing.

3. Make sure the saw is on a ﬁrm level surface and properly secured.

4. Use only the recommended accessories.

5. Use extra caution with very large, very small or awkward workpieces.

9. USE EXTRA SUPPORTS to prevent workpieces

from sliding off the table top. Never use another person to support the workpiece.

10. WORKPIECES must be secured so they do not

twist, rock or slip while being cut.

11. PLAN intricate and small work carefully to avoid

pinching the blade. Avoid awkward operation and hand positions to prevent accidental contact with

the blade.

12. SMALL PIECES should be secured with jigs or

ﬁxtures. Do not hold pieces that are so small your ﬁngers are under the blade guard.

13. SUPPORT round work properly (with a V-block or

clamped to the miter gauge) to prevent it from rolling and the blade from biting.

14. CUT only one workpiece at a time. Make sure the

table is clear of everything except the workpiece and guides before turning the saw on.

15. ALWAYS WATCH the saw run before each use.

If there is excessive vibration or unusual noise, stop immediately. Turn the saw off. Unplug immediately. Do not start the saw again until the problem has been located and corrected.

6. Keep hands away from the blade at all times to prevent accidental injury.

7. Do not remove jammed or cutoff pieces until the blade has stopped.

8. Maintain proper adjustment of blade tension, blade guides and thrust bearings.

9. Hold the workpiece ﬁrmly against the table.

10. Adjust the upper guide to clear the workpiece.

ELECTRICAL REQUIREMENTS AND SAFETY

POWER SUPPLY AND MOTOR SPECIFICATIONS

WARNING

To avoid electrical hazards, ﬁre hazards, or damage to the tool, use proper circuit protection. Use a seperate electrical circuit for your tool. Your saw is wired at the factory for 120 V operation. Connect to a 120 V, 10 Amp circuit and use a 10 Amp time delay fuse or circuit breaker. To avoid shock or ﬁre, if power cord is worn, cut, or damaged in any way, have it replaced immediately.

GROUNDING INSTRUCTIONS

WARNING

This tool must be grounded while in use to protect the operator from electrical shock.

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least

resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching receptacle that is properly installed and grounded in accordance with all local codes and ordinances.

DO NOT MODIFY THE PLUG PROVIDED.

If it will not

ﬁt the receptacle, have the proper receptacle installed by a qualiﬁed electrician.

IMPROPER CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. If repair or replacement of the electrical cord or plug is necessary, do not connect the equipment grounding conductor to a live terminal.

CHECK with a qualiﬁed electrician or service person if you do not completely understand the grounding instructions, or if you are not certain the tool is properly grounded.

USE only 3-wire extension cords that have three-pronged grounding plugs with three-pole receptacles that accept the tool’s plug. Repair or replace damaged or worn cords immediately.

Use a separate electrical circuit for your tool. This circuit must not be less than #16 wire and should be protected with a 10 Amp time lag fuse. Before connecting the motor to the power line, make sure the switch is in the off position and the electric current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage will damage the motor.

GUIDELINES FOR EXTENSION CORDS USE THE PROPER EXTENSION CORD. Make sure

your extension cord is in good condition. Use an extension cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power, overheating

and burning out of the motor. The table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualiﬁed technician before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.

MINIMUM GAUGE FOR EXTENSION CORDS (AWG)

Ampere Rating Total length of Cord

More Than Not More Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16

WARNING

120 V 25 50 100 150 ft. (7.62 15.24 30.48 45.72 m) 240 V 50 100 200 300 ft. (15.24 30.48 60.96 91.44 m)

AWG- American Wire Gauge

14 12 Not Recommended

This tool is for indoor use only. Do not expose to rain or use in damp locations.

This tool is intended for use on a circuit that has a receptacle like the one illustrated in Fig. 1. Fig. 1 shows a three-pronged electrical plug and receptacle that has a grounding conductor. If a properly grounded receptacle is not available, an adapter (Fig. 2) can be used to temporarily connect this plug to a two-contact grounded receptacle. The adapter (Fig. 2) has a rigid lug extending from it that MUST be connected to a permanent earth ground, such as a properly grounded receptacle box.

CAUTION

In all cases, make certain the receptacle is properly grounded. If you are not sure, have a qualiﬁed electrician check the receptacle.

Fig. 1

Three-Pronged Plug

Grounding Prong

Properly Grounded Three-Pronged Receptacle

Fig. 2

Grounding Lug

Make sure this is connected to a known ground.

Two

-Pronged

Receptacle

Adapter

240 VOLT SINGLE PHRASE OPERATION

WARNING

To avoid injury, disconnect the motor from power source outlet before reconnecting the wire.

The motor supplied with your machine is a dual voltage, 120/240 volt motor. It is shipped ready-to-run for 120 volt operation. However, it can be converted for 240 volt op eration, reconnect the motor wire as the wiring diagram on page 20. A qualiﬁed electrician should do the conversion, or the machine can be taken to an Authorized Service Center. When completed, the machine must conform to the Na tional Electric Code and all local codes and ordinances. The machine is converted by re-wiring the motor for 240 volts, installing a 240 volt plug on the power supply cord and replacing the switch with one that is rated for 240 volt operation. Be sure the 240 volt plug is only used in an outlet having the same conﬁguration as the plug illustrated in Fig. 1. No adapter should be used with the 240 volt plug.

CAUTION

In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a quali ﬁed electrician check the receptacle.

TOOLS NEEDED FOR ASSEMBLY

Supplied Not Supplied

Hex key

Phillips screwdriver

Adjustable wrench

12 mm wrench

Combination square

Straight edge

Feeler gauge (size 0.02 in.)

CARTON CONTENTS

UNPACKING AND CHECKING CONTENTS

Carefully unpack the band saw and all its parts, and compare against the list below and the illustration on the next page. With the help of an assistant place the saw on a secure surface and examine it carefully.

WARNING

● To avoid injury from unexpected starting or electrical

shock, do not plug the power cord into a source of power during unpacking and assembly. This cord must remain unplugged whenever you are adjusting/ assembling the saw.

The saw is heavy and should be lifted with care.

●

If needed, get the assistance of someone to lift and

move the saw.

If any part is missing or damaged, do not attempt

●

to assemble the band saw, or plug in the power cord until the missing or damaged part is correctly replaced.

TABLE OF LOOSE PARTS ITEM DESCRIPTION QUANTITY

A. Foot pads & hex nuts B. Bag: Carriage screws Hex nuts w/ washers Screw w/ washers C. Door knob / hex screw / washer D. Stand attachment hardware Large washers Hex nuts

E. Sawdust port

Washers F. Trunnion

Short hex bolts Hex nut Table lock knob Washers G. Trunnion support bracket H. Table with insert I. Power cord bracket Cross head bolts Hex key J. Band saw with motor K. Miter gauge L. Top plate M. Tool tray N. Left / right side plate O. Back plate P. Door plate

Long hex bolts

Hex bolts

support hardware

Long bolt

16 16 8 1 each

8 4 4 1 2 2

1 2 1 2 2 1 1 2 2 1 1 1 1 1 1 each 1 1

UNPACKING YOUR BAND SAW

N O

Upper cover

ON/OFF switch

KNOW YOUR BAND SAWKNOW YOUR BAND SAW

Lower blade

Upper blade wheel

Blade guard

Upper blade support bearing

Upper blade guide

Table insert

support bearing

Lower blade guide

Blade

Wheel brush

Lower cover

Sawdust port

Mounting holes

Table

aligning pin

Table trunnion

Upper guide lock knob

Blade guide slide knob

Table tilt stop bolt

Table tilt scale

Table lock knob

Upper guide

bar Lower blade wheel

Motor

Table

removed for

Table clarity of illustration

Blade tension knob

Blade tension gauge

Blade tracking knob

Power cord storage

Motor cord

Belt tension handle

Cabinet stand

Stand top plate

GLOSSARY OF TERMS

BAND SAW TERMS

BLADE GUIDES — Support the blade and keep it from

twisting during operation. Blade guides must be adjusted when blade is changed or replaced.

UPPER GUIDE LOCK KNOB — locks the upper slide. Use it after adjusting the upper guide assembly to make sure upper blade guide just clears workpiece before cutting. Upper guide lock knob must be tightened before the band saw is turned on.

TABLE LOCK KNOB — locks the table in place.

TILT (BEVEL) SCALE — shows the degree the table is

tilted for bevel cutting.

BLADE TENSION KNOB — controls the amount of blade tension when changing blades.

BLADE TRACKING KNOB — adjusts blade position so blade always runs in the center of the wheel.

SAWDUST PORT — helps keep the machine free from sawdust. The sawdust port makes an excellent hook-up for a wet/dry vacuum.

ON/OFF SWITCH — has a built-in child safety lock. To lock the switch in the OFF position, remove the switch key from the switch.

RESAW — A cutting operation to reduce the thickness of the workpiece to make thinner workpiece.

RESIN — A sticky sap that has hardened.

RIPPING CUT — A cutting operation along the length of

the workpiece.

R.P.M. — Revolutions per minute. The number of turns completed by a spinning object in one minute.

SAW BLADE PATH — The area of the workpiece or table top directly in line with the travel of the blade or the part of the workpiece that will be cut.

SET — The distance between two saw blade teeth tips, that are bent outward in opposite directions to each

The further apart the tips are, the greater the set.

other.

TRAILING EDGE — The workpiece edge last cut by the blade.

WORKPIECE — The item being cut. The surfaces of a workpiece are commonly referred to as faces, ends and edges.

WORKTABLE — The surface on which the workpiece rests while performing a cutting or sanding operation.

WOODWORKING TERMS

BEVEL CUT — An angle cut made through the face of a

workpiece.

COMPOUND CUT — A simultaneous bevel and miter cut.

CROSSCUT — A cut made across the width of the workpiece.

F.P.M. — Feet per minute. Used in reference to the surface speed of the saw blade.

FREE HAND — Performing a cut without using a fence (guide), hold-down or other proper device to prevent the workpiece from twisting during the cutting operation.

GUM — A sticky sap-based residue from wood products.

HEEL — Misalignment of the blade.

KERF — The material removed by the blade in a

through cut, or the slot produced by the blade in a non-through or partial cut.

LEADING EDGE — The front edge of the workpiece pushed into the cutting tool ﬁrst.

Surface

Workpiece

Leading Edge

Kerf

Saw Blade Path

Trailing Edge

MITER CUT — An angle cut made across the width of a workpiece.

ASSEMBLY AND ADJUSTMENTS

Estimated Assembly Time: 50 - 60 minutes.

WARNING

For your safety, never connect plug to power source receptacle until all assembly and adjustment steps are complete, and you have read and understood the safety instructions.

ASSEMBLING CABINET STAND (FIG. A, A-1, A-2, A-3, A-4, A-5)

1. Bag “A” - Thread the feet (2) with hex nut (1) into

each hole of two side plates (3, 8).

NOTE: Adjust the level of stand. When the feet are adjusted properly, turn the hex nuts against the leg of side plate to secure them. Loosen the hex nut before any adjustment.

Fig. A

Fig. A-2

5. Bag “B” - Mount the back plate (9) to the top plate

(7) and tool tray (4), then fasten with four screws w/ washers (10)

Fig. A-3

2. Bag “B” - Attach R.H. side plate (3) (with holes on

side) to the tool tray (4) with four carriage bolts (5) and hex nut w/ washers (6) Repeat above steps for the L.H. plate (8). Securely

3. tighten nuts.

Fig. A-1

6. Bag “C” - Insert the door knob (11) to the hole of

door plate (12) with one hex screw (13) and washer (14).

Fig. A-4

Bag “B” - Attach top plate (7) to the L.H. side plate

(8) and R.H. plate (3) with eight carriage bolts (5) and hex nut w/ washers (6). NOTE: Top plate ﬂanges ﬁt inside side plates.

7. Mount the door plate (12) to the R.H. side plate (3) hinges and fasten with four screws w/ washers (10).

NOTE: Hinge goes behind side plate lip.

8. Place stand on level surface and adjust the feet if needed.

Fig. A-5

INSTALLING THE SAWDUST PORT (FIG. C )

The sawdust port has a 2-1/2 in.(63.5 mm, O.D.)/2-1/4

in.(57.2 mm, I.D.) diameter opening, suitable for attach ing to a wet/dry vacuum hose to help keep the work area free of sawdust.

1. Open the lower cover (1).

2. Bag “E” - Attach the sawdust port (2) to the edge

of the wheel cover, using the hex head bolts (3) and washers (4).

3. Tighten the bolts (3) and close the cover.

NOTE: Make sure all screws and nuts are tight and stand is on a stable surface before mounting saw.

WARNING

Although compact, this saw is heavy and should be lifted with care. If needed, get the assistance of someone to lift and move the saw.

ASSEMBLING BAND SAW TO CABINET STAND (FIG. B)

1. Lift the saw body (1) and place on the stand (2),

aligning the mounting holes (3) of the saw base with the four mounting holes on the top plate of stand.

2. Bag “D” - Attach the band saw to the stand with four

long hex head bolts (4) and four ﬂat washers (5).

3. Place a ﬂat washer (5) and hex nut (6) on each bolt

from the underside of the top plate.

4. Hold bolt head with a separate wrench and tighten all

mounting bolts and nuts with a wrench.

Fig. B

Fig. C

ASSEMBLING THE BAND SAW TABLE (FIG. D, E, F)

Mounting the trunnion support bracket (Fig. D)

1. Place the trunnion support bracket (1) on the saw body as shown, then align the mounting holes.

2. Bag “F” - Place the washers (2) on the hex head bolts (3), and insert into the threaded holes, through the bracket and saw body. Tighten the bolts.

3. Thread a nut (4) into the table stop bolt (5) and the rear tab (6) on the trunnion support bracket (1).

4. Tighten the nut down onto the bracket tab.

Fig. D

5 4

1 4

6 1

Mounting the table (Fig. E, F)

5. Remove the table insert (13) from the table.

6. Guide the table slot (14) over the saw blade and rotate a 1/4 turn, so the slot is perpendicular to

the blade.

7. Bag “F” - Placing the lock knob bolts (10) through the trunnion bracket holes (15) as shown, lower the table onto the trunnion bracket.

8. Place a lock knob (16) on each lock knob bolt. Adjust the table by aligning the zero scale mark to the scale pointer (17) and tighten the knobs.

9. Replace the table insert (13), aligning the indents.

10.Place the table aligning pin (18) in the hole (19) at the front of the table, and tighten it.

Fig. E

INSTALLING AND REMOVING BLADES (FIG. G)

WARNING

To avoid injury from accidental starting, always turn the switch OFF and remove the plug from the power source before moving, replacing, or adjusting the blade.

Removing

1. Loosen the blade tension by turning the blade tension knob (1) counterclockwise.

2. Remove the table insert (2) and remove the table aligning pin (3) from the table.

3. Open the upper and lower wheel cover doors (4).

4. Loosen the two Phillips screws (5) and remove the upper blade guard (6).

5. Remove the blade (7) from the upper and lower blade guides (8).

6. Carefully pull the blade from the side slot (9) and from the wheels (10).

7. Swing the left side of the blade toward you, turning the blade so it will ﬁt through the slot (11) in the table, and remove.

NOTE: The available usage of blade length is from

91-1/2 to 93-1/2 in. (2324 to 2374.9 mm).

Fig. F

Fig. G

Installing

1. Make sure the blade tension knob (1) is turned counterclockwise enough to get blade over pulleys.

2. Remove old blade as explained in “Removing” section.

3. Guide the new blade (7) through the table slot (11). Make sure the blade teeth are pointing forward

and down. NOTE: To avoid lifting the workpiece, the blade teeth must point downward toward the table.

4. Swinging the left side of the blade away and back, place the blade on the upper and lower wheels (10).

5. Place the blade carefully between the upper and lower blade guides (8).

6. Slide the blade into the slot (9) at the left of the wheels, and make sure the blade is positioned at the middle of the wheels.

7. Turning the blade tension knob (1) clockwise, tighten the tension until the blade is tight on the wheels.

8. Replace the upper blade guard (6) and tighten the two Phillips screws (5).

9. Replace the table insert (2) and the table aligning pin (3).

10.Adjust the blade tracking and tension properly

(See ADJUSTMENT INSTRUCTIONS section)

before operating the band saw.

WARNING

To avoid injury, the blade tension, tracking, and upper and lower guides and bearings must be properly adjusted before operating the band saw. (See ADJUSTMENT INSTRUCTIONS section)

WARNING

Before operation always make sure the blade is in center of table insert slot.

MITER GAUGE (FIG. H)

A miter gauge (1) is supplied with your band saw to be used in the table slot (2) on the right side of the blade.

The miter gauge can be adjusted from 0° to 60° right or left to maintain an accurate angle for your workpiece.

INSTALLING POWER CORD STORAGE (FIG. I)

1 . Bag “I” - Power cord brackets (1) are provided for

convenient cord storage. Attach the power cord brackets to the back of the saw body, as shown, with two Phillips head screws (2). Tighten the screws.

2. Wrap the power cord onto the brackets when the band saw is not in use. This can prevent damage to the cord.

Fig. I

2 1

ADJUSTMENT INSTRUCTIONS

WARNING

To avoid injury, turn the switch OFF and unplug the band saw from the power source before making any adjustments.

TABLE ADJUSTMENTS (FIG. J, K)

Tilting the table (Fig. J)

The band saw table (1) can be tilted from 0° to 45° right.

1. Loosen both table lock knobs (2) underneath

the table.

2. Tilt the table to the desired angle on the scale (3)

underneath the table.

3. Tighten the two table lock knobs.

Fig. J

Fig. H

ADJUSTING THE 90° TABLE STOP (FIG. K)

1. Loosen the table lock knobs (1) and tilt the table to the right.

2. Loosen the nut (2) on the table stop bolt (3) and lower the stop bolt as far as possible.

3. Tilt the table until it rests on the stop bolt.

4. Place a combination square (4) on the table with the heel of the square against the saw blade (5).

5. Adjust the tilt of the table left or right until it is 90° to the blade. Make sure there is no space between the square and the blade. Tighten the table lock knobs.

6. Adjust the table stop bolt up until it touches the table. Tighten the jam nut down to the support bracket.

7. Loosen the lock knobs and see that the table is resting on the stop bolt.

8. Check the square to make sure the table is still square to the blade. If not, re-adjust the stop bolt.

9. When the adjustment is accurate at 90°, align the pointer (6) to 0° on the scale (7).

Fig. K

Fig. L

BLADE TRACKING (FIG. M)

WARNING

To avoid injury, turn the switch OFF and disconnect the saw from the power source before making any adjustments. NEVER make tracking adjustments with the machine running.

Blade tracking was set at the factory. When adjustment is needed please follow the procedure below.

BLADE TENSION

WARNING

To avoid injury, turn the switch OFF and disconnect the

saw from the power source before making any adjustments. NEVER make tension adjustments with the machine running. Blade tension was set at the factory. When adjustment is needed please follow the procedure below. The gauge (1) on the bracket (2) at the rear of the upper wheel indicates the proper tension for the various blade widths.

1. Set the blade tension gauge (1) to correspond with

the blade width, as shown.

2. Turn the blade tension knob (3) clockwise to tighten

the blade, counterclockwise to loosen.

3. As you become familiar with the saw, you may try to

change the tension settings.

NOTE: Changes in blade width and type of material being cut will have an effect on the blade tension. Too much or too little tension could break the blade

1. The blade (1) must be tensioned properly before adjusting the tracking. (See BLADE TENSION

2. Open the upper cover.

3. Move the blade guides (2) and support bearings (3) away from the blade, if necessary.

4. Rotate the wheel (4) slowly forward by hand, and check the position of the blade on the wheel. The blade should remain centered on the wheel as it turns.

5. If the blade moves toward the front of the wheel, turn the tracking knob (5) on the rear of the band saw clockwise. This tilts the top of the wheel and moves the blade toward the center.

6. If the blade moves toward the back edge, turn the tracking knob counterclockwise, moving the blade toward the center.

NOTE: Turn the tracking knob SLIGHTLY to make blade tracking adjustments.

Fig. M

UPPER BLADE GUIDE ASSEMBLY (FIG. N)

WARNING

To avoid injury, turn the switch OFF and disconnect the saw from the power source before making any adjmstments. NEVER make adjustments with the machine running.

1. Loosen the wing nut (1) and the lock knob (2), and hold the knob (3) to move the blade guide assembly (4) to 1/8 in. (3.2 mm) above the workpiece.

2. If necessary, rotate the assembly until the guide blocks (5) are ﬂat (parallel) to the blade (6). Tighten the lock knob.

UPPER BLADE GUIDES AND BLADE SUPPORT BEARING (FIG. O, P)

WARNING

The blade guard has been removed for clarity of illustration. To avoid injury, never operate the band saw without all guards in place and in working order.

WARNING

To avoid injury, turn the switch OFF and disconnect the saw from the power source before making any adjustments. NEVER make adjustments with the machine running. NOTE: Make sure the blade is tensioned and tracking properly. Adjust the blade guides and support bearing each blade tension and tracking adjustment. When the upper blade guides and support bearings are adjusted, the lower guides and bearings should also be adjusted.

Blade guides (Fig. O)

Blade guides have been set at the factory but should be checked.

1. Make sure the blade is tensioned and tracking properly.

2. Loosen the front hex socket screws (1) with a hex wrench supplied.

3. Move the guide blocks (2) as close to the blade (3) as possible without pinching it.

4. Using a feeler gauge, make sure the space between guide block and the blade measured is 0.002 in. (0.05 mm, the thickness of a dollar bill).

5. Tighten the hex socket screws.

6. Loosen the side thumb screw (4) by turning counterclockwise.

7. Turn the rear knob (5) to move the blade guide brackets in or out until the guide blocks (2) are just behind the blade teeth.

8. Tighten the thumb screw.

Fig. O

after

Fig. N

Support bearing (Fig. P)

Support bearing has been set at the factory but should be checked.

9. Loosen the knob (6).

10. Turning the rear knob (7), move the support bear-

ing (8) in or out until the bearing is 1/64 in. (0.4 mm) behind the blade.

11. Tighten the knob (6).

NOTE: This blade support bearing prevents the blade from moving back too far and damaging the saw teeth setting.

12. Check the lateral position of the support bearing (8). The vertical back edge of the blade (3) should overlap the front face of the support bearing 1/16 in.(1.6 mm)

to 1/8 in.(3.2 mm) to the left of the right

bearing edge, as shown.

Fig. P

5. Loosen the side hex socket screw (4). Move the guide block support bracket (6) in or out until the blocks are just behind the saw teeth. Tighten the screw. (Fig. R)

Fig. R

LOWER BLADE GUIDES AND SUPPORT BEARING (FIG. Q, R)

WARNING

To avoid injury, turn the switch OFF and disconnect the saw from the power source before making any adjustments. NEVER make adjustments with the machine running. NOTE: Make sure the blade is tensioned and tracking properly. The lower blade guides and support bearings should always be adjusted after the blade is tensioned, the tracking is adjusted, and the upper blade guides and upper support bearings are properly adjusted.

Blade guides

1. Loosen both front hex socket screws (1) with a hex wrench.

2. Move the guide blocks (2) as close to the sides of the blade (3) as possible without pinching it.

3. Using the feeler gauge, measure the spaces between the guide blocks and the blade.

Adjust to 0.002 in. (0.05 mm).

4. Tighten the hex socket screws. (Fig. Q)

Support bearing

6. Loosen the bearing hex socket screw (7) with the hex wrench.

7. Move the blade support bearing shaft (8) in or out until the support bearing (9) is 1/64 in.(0.4 mm) behind the saw blade.

8. Tighten the bearing hex socket screw.

9. The back edge of the blade (3) should be positioned 1/16 in.(1.6 mm) to 1/8 in.(3.2 mm) from the right edge of the support bearing (9), as shown.

PULLEY ALIGNMENT (FIG. S)

The pulley alignment has been adjusted at the factory and shouldn’t require further adjustment. If adjustments are required or belt needs replacing, please follow these procedures:

1. Place a straight edge in the front groove of both

pulleys, behind the blade wheel.

2. Turn the hex socket screw (1) in the side of the motor pulley (2) to loosen the pulley on the shaft.

3. Adjust the motor pulley in or out on the motor shaft (3) to align the edges of the two pulleys.

4. When aligned, tighten the hex socket screw on the side of the motor pulley.

Fig. S

Fig. Q

OPERATION

BASIC SAW OPERATIONS

“ON/OFF” SWITCH (FIG. T)

The keyed switch is intended to prevent unauthorized use of the band saw. I. To turn the band saw ON insert the black switch key

(1) into the key slot in the center of the switch (2).

2. Push the key ﬁrmly into the slot, then push switch (2) to the ON position to start the band saw.

3. To turn the band saw OFF push the switch (2) to the OFF position.

4. Remove the black switch key, when the saw has come to a complete stop, by gently pulling it outward.

WARNING

Remove the black switch key (1) whenever the saw is not in use. Place it in a safe place and out of reach of children.

Fig. T

To avoid twisting the blade do not turn sharp corners; saw around corners.

A band saw is basically a “curve-cutting” saw. It is not capable of doing intricate inside cutting as can be done with a scroll saw.

It is also used for straight line operations such as crosscutting, ripping, mitering, beveling, compound cutting, and resawing.

WARNING

To avoid blade breakage, ﬁre or other damage or injury, NEVER use this band saw to cut metals.

CUTTING CURVES

When cutting curves, carefully turn the workpiece so the blade may follow without twisting. If the curve is so sharp that you repeatedly back up and cut new kerf, use a narrower blade, or a blade with more set (teeth further apart). When a blade has more set, the workpiece turns easier but the cut is rougher.

When changing a cut, do not withdraw the workpiece from the blade. The blade may get drawn off the wheels. To change a cut, turn the workpiece and saw out through the scrap material area.

When cutting long curves, make relief cuts as you go along.

GENERAL CUTTING

WARNING

For your safety, read and understand all SAFETY INSTRUCTIONS on pages 4 - 6 before using the band saw.

Operating band saws involves a certain amount of hazard. Before attempting regular work, use scrap lumber to check the settings, and to get the feel of operating the band saw. Read instructions and plan your work before cutting a workpiece.

Do not turn the power ON until after you have made all adjustments, checked that the guard is in place, and turned the wheel by hand to make sure all parts work properly. Always keep the guide assembly 1/8 in. (3.2 mm) above the workpiece.

Do not force the workpiece against the blade. Light contact permits easier cutting and prevents unwanted friction and heating of the blade.

Sharp saw blades need little pressure for cutting. Steadily move the workpiece against the blade without forcing it.

ClRCLE CUTTING (FIG. U)

1. Adjust the guide assembly to 1/8 in.(3.2 mm) above the workpiece.

2. Use both hands while feeding the work into the blade. Hold the workpiece ﬁrmly against the table. Do not force the work and operate with gentle pressure.

3. The smallest diameter circle that can be cut is determined by the width of the blade. For example, a 1/4 in.(6.4 mm) wide blade will cut a minimum diameter of approximately 1-1/2 in.(38.1 mm).

Fig. U

(12.7 mm) (25.4 mm) (38.1 mm) (50.8 mm) (63.5 mm)

1/2 in. D

1 in. D

1-1/2 in. D

1/8 in.

3/16 in. 1/4 in.

(3.2 mm) (4.8 mm) (6.4 mm) (9.5 mm) (12.7 mm)

2 in. D

2-1/2 in. D

3/8 in. 1/2 in.

Minimum Circle Diameter

Blade Width

BLADE SELECTION (FIG. V)

CAUTION

Blade teeth are sharp. Use care when handling a saw blade.

CAUTION

For longest wear and best cutting results, use the correct blade thickness, width, and temper for the type of material you will cut.

When sawing small curves and delicate work, use narrow blades. Otherwise, use the widest blade as possible. (See Fig. U on page 18)

For cutting wood and similar materials with this band saw, purchase blades in width up to 1/2 in.(12.7 mm), and a length of 93-1/2 in.(2374.9 mm).

Do not cut metals with this band saw.

Fig. V

Common causes of blade breakage:

Poor guide alignment and adjustment.

●

Forcing or twisting a wide blade around a short

●

radius.

Feeding too fast.

●

Dull teeth or not enough set.

●

Too much blade tension.

●

Setting top guide assembly too high above the

●

workpiece.

Lumpy or improperly ﬁnished braze or weld on the

●

blade.

Continuous running of blade when not cutting.

●

Fig. W

Operation Recommended Blade Width (Inches) Cross Cutting 1/4, 3/8, 1/2 in. (6.4 ,9.5, 12.7 mm)

Mitering 1/4, 3/8, 1/2 in. (6.4 ,9.5, 12.7 mm) Beveling 1/4, 3/8, 1/2 in. (6.4 ,9.5, 12.7 mm) Compound

Cutting Circle Cutting See chart on page 18 Curve Cutting 1/8, 1/4 in. (3.2, 6.4 mm)

CHANGING SPEED SETTING (FIG. W)

WARNING

To avoid injury, turn the power switch OFF and disconnect the band saw from the power source.

1. Loosen the belt tension by turning the belt tension handle (6) and rotating the motor counterclockwise until it stops.

2. Open the lower wheel cover and re-position the V-belt (3).

Changing the speed from 1630 to 2730 FPM:

●

ﬁrst remove belt (3) from the band saw pulley(4); reposition in the saw pulley groove (1).

Change the speed from 2730 to 1630 FPM: ﬁrst

●

remove belt (3) from the motor pulley (5) and reposition in the motor pulley groove (2). Remove the belt from the saw pulley (4) and reposition in the saw pulley groove(2).

NOTE: The pulley belt is properly tensioned when there is 1/2 in. (12.7 mm) deﬂection if pressed in the center of the pulleys.

3. Tighten the belt tension by turning the belt tension handle (6).

1/4, 3/8, 1/2 in.

(6.4 ,9.5, 12.7 mm)

2 1

MOTOR

NOTE: After re-adjusting belt position and belt tension, verify and re-adjust the settings for the blade tension and tracking position, guides and bearings (See Adjustment section).

INSTALLING A NEW BELT (FIG. X)

WIRING DIAGRAM

120 V

MOTOR

WHITE

YELLOW

GRAY

RED

BLACK

GREEN

BLACK

WHITE

YELLOW

GRAY

RED

BLACK

GREEN

BLACK

240 V

MOTOR

1. Open the lower wheel door.

2. Loosen the blade tension by turning the blade

tension lock knob (1).

3. Remove the blade from the lower blade wheel.

4. Loosen and remove the hex head bolt (2) and

ﬂange (3) on the lower blade wheel.

5. Remove the lower blade wheel.

6. Turn the belt tension handle (4) on the rear of the

saw housing to loosen the v-belt tension.

7. Remove the v-belt (5).

8. Check the alignment of the two pulleys.

9. If the edges of the two pulleys are not aligned, see

“PULLEY ALINGMENT” in ADJUSTMENT section.

10. Place the new v-belt on the saw pulley and the

motor pulley. See OPERATION section

“CHANGING SPEED SETTINGS” on

page 19 for

proper belt placement.

11. When the

pulley belt is positioned properly, tighten

the v-belt tension by turning the belt tension handle.

NOTE: The pulley belt is properly tensioned when

there is a 1/2 in. (12.7 mm) deﬂection if pressed in the center of the pulleys.

12. Replace the blade wheel. Push the wheel in ﬁrmly

until it is touching the saw pulley. Replace and tighten the ﬂange and nut.

13. Reinstall the blade. (See INSTALLING BLADES

Section on page 13)

14. Adjust the blade tension, tracking, the upper and

lower blade guides and bearings before operating the band saw.

240 V OPERATION -

WARNING

CHANGING WIRES (FIG. Y, Z)

To avoid injury, disconnect the motor from power source outlet before reconnecting the wire.

The band saw provided a dual voltage, 120 V and 240 V, motor. To operate the band saw at 240 V, single phase, please reconnect the motor wires

1. Remove the screw (1) and wire cover (2).

Fig. Y

2. Reconnect the motor wires and power wires as shown in the wiring diagram

Fig. Z

WARNING

To avoid injury, the blade tension, tracking, and upper and lower guides and bearings must be properly adjusted before operating the band saw. (See ADJUSTMENT INSTRUCTIONS section)

Fig. X

CAUTION

A qualiﬁed electrician should do the conversion, or the machine can be taken to an Authorized Service Center. When completed, the machine must conform to the Na

tional Electric Code and all local codes and ordinances.

The machine is converted by re-wiring the motor for 240 volts, installing a 240 volt plug on the power supply cord and replacing the switch with one that is rated for 240 volt operation.

Be sure the 240 volt plug is only used in an outlet plug. No adapter should be used with the 240 volt plug.

In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a quali

ﬁed electrician check the receptacle.

NOTE: The 240 volt plug is not supplied with this product. Please check with a qualiﬁed electrician for the correct plug.

MAINTENANCE

GENERAL MAINTENANCE

WARNING

For your own safety, turn switch OFF and remove the plug from power source receptacle before maintaining, cleaning,adjusting, or lubricating your band saw.

WARNING

To avoid ﬁre or toxic reaction, never use gasoline, naphtha, acetone, lacquer thinner or similar highly volatile solvents to clean the band saw.

WARNING

To avoid eye injury from blowing debris, wear safety goggles when blowing out sawdust.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

BAND SAW

Sawdust will accumulate under the table and base. This could cause difﬁculty in the movement of the table when setting up a band saw cut. Frequently blow out or vacuum up the sawdust. Keep your band saw clean. Remove the sawdust from the inside. Vacuum or blow out frequently.

Do not allow debris to build up on the table, the guides, or the support bearings. Clean them with gum and pitch remover. NOTE: Do not immerse the support bearings in the gum and pitch remover.

Apply a thin coat of paste wax on the table so that the wood slides easily while cutting.

BLADE WHEEL TIRES

Pitch and sawdust that build up on the tires should be removed with a stiff brush or scraped off with a piece of wood. NOTE: To avoid damaging the tires do not use a sharp knife or any kind of solvent.

ADJUSTING THE UPPER BLADE GUIDE TRAVEL (FIG. AA)

If the upper guide bar assembly will not move up and down easily or falls when the lock knob is loosened, the following adjustment should be performed.

1. Remove the guide bar lock knob (1).

2. Using a 5mm hex “L” wrench, tighten or loosen the

screw (2) located behind the lock knob.

3. Move the guide bar (3) up and down to check for

smooth movement and ability to hold its position.

4. Make further adjustments to the screw as required.

Properly adjusted, the guide bar should move smoothly and hold its position when released.

5. Reinstall the guide bar lock knob (1).

Fig. AA

LUBRICATION

All of the bearings are packed with grease at the factory. They require no further lubrication.

CAUTION

Never put lubricant on the blade while it is spinning.

When the tires become worn, they should be replaced. When replacing the tires, stretch them around the wheels but do not glue them on.

MOTOR

Frequently blow or vacuum out any sawdust from the motor. Follow lubrication instruction on the motor label.

WARNING

To avoid electrocution or ﬁre, immediately replace a worn, cut or damaged power cord.

TROUBLESHOOTING GUIDE

WARNING

To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.portercable. com. You can also order parts from your nearest Porter-Cable Factory Service Center or Porter-Cable Authorized War ranty Service Center. Or, you can call our Customer Care Center at (888) 609-9779.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about Porter-Cable, its factory service centers or authorized warranty service centers, visit our website at www.portercable.com or call our Customer Care Center at (888) 609-9779. All repairs made by our service centers are fully guaranteed against defec tive material and workmanship. We cannot guarantee repairs made or attempted by others. You can also write to us for information at (888) 609-9779 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.).

Power Tool Specialists, Inc. 684 Huey Road, Rock Hill, SC 29730,

GENERAL

PROBLEM PROBLEM CAUSE SUGGESTED CORRECTIVE ACTION

Blade does not run in the center of upper wheel.

Band saw slows down when cutting.

Blades breaking 1. Too much tension on the

Blade dulls too quickly.

Band saw vibrates. 1. Too much tension on motor

1. Not tracking properly.

2. Defective blade.

1. Belt too loose.

2. Cutting too small a radius.

3. Dull blade.

4. Overloading motor.

blade.

2. Kink in the blade caused by cutting too small a radius or turning the material too fast when cutting.

1. Blade guides set too close to the teeth.

2. Cutting incorrect material.

belt.

1. Adjust tracking. See ASSEMBLY AND ADJUSTMENTS section "BLADE TRACKING".

2. Replace blade.

1. Adjust belt tension. See ASSEMBLY AND

ADJUSTMENTS section "BLADE TENSION".

2. Stop feeding, back up the material slightly, until band

saw speeds up.

3. Replace blade.

4. Slow down, trying to cut too fast. See "MOTOR

TROUBLESHOOTING GUIDE".

1. Adjust belt tension. See ASSEMBLY AND

ADJUSTMENTS section "BLADE TENSION".

2. Use correct cutting technique. See OPERATION

section section "GENERAL CUTTING".

1. Adjust upper and lower blade guides.

2. See OPERATION section "BLADE SECTION".

1. Adjust tracking. See ASSEMBLY AND ADJUSTMENTS section "INSTALL THE BELT"

MOTOR

PROBLEM PROBLEM CAUSE SUGGESTED CORRECTIVE ACTION

Noisy operation. 1. Incorrect belt tension.

2. Loose motor pulley.

3. Loose pulley cover.

Motor will not start. 1. Not plugged into power outlet.

2. Switch and key not in ON position.

3. Motor cord cut or abraded.

4. Plug on cord is faulty.

5. Fuse on circuit breaks open.

6. Faulty motor.

1. Adjust tension. See ASSEMBLY AND ADJUSTMENTS section "INSTALL THE BELT".

2. Readjust and tighten motor pulley set screw.

3. Readjust and tighten pulley cover mounting screws.

1. Plug it into the power outlet.

2. Insert key and turn the switch ON.

3. Re-set; may be too many machines on line.

4. Contact Porter-Cable Service Center or Authorized Service Station for repair or replacement.

Motor will not start and fuse or circuit breaker opens.

Motor fails to develop full power.

Motor overheats. 1. Overload on motor.

Motor stalls or slows. 1. Motor overload.

Frequent fuse or circuit breaker failure.

1. Too many electrical machines.

2. Incorrect fuse.

3. Wheels do not rotate.

4. Undersized extension cord.

5. Short circuit.

1. Low line voltage.

2. Faulty motor or capacitor.

2. Poor ventilation of motor.

3. Capacitor failure.

2. Low line voltage.

3. Loose wire connections.

4. Faulty motor.

1. Motor overload.

2. Overload of electrical circuit.

3. Incorrect fuse or circuit breaker.

1. Turn off other machines and try again.

2. Try time delay fuse, or go to circuit with higher rated fuse or circuit breaker.

3. Unplug and turn wheels by hand, move obstruction.

4. Use correct size extension cord, see page 6.

5. Cord, plug, or motor need repair. Cable Service Center or Authorized Service Station for repair.

1. Check power line for proper voltage.

2. Contact Porter-Cable Service Center or Authorized Service Station for repair.

1. Reduce load to motor, feed work slower into blade.

2. Unplug and clean out around motor. Provide better air circulation.

3. Contact Porter-Cable Service Center or Authorized Service Station for repair.

1. Reduce load to motor, feed work slower into blade.

2. Check power line for proper voltage.

3. Contact Porter-Cable Service Center or Authorized Service Station for repair.

1. Reduce load to motor, feed work slower into blade.

2. Too many electrical appliances on same circuit.

3. Have electrician upgrade service to outlet.

Contact Porter-

For assistance with your product, visit our website at www.portercable.com for a list of service centers, or call the Porter-Cable Customer Care Center at (888) 609-9779.

ACCESSORIES AND ATTACHMENTS

ACCESSORIES

WARNING

Since accessories, other than those offered by PorterCable, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only Porter-Cable recommended accessories should be used with this product.

A complete line of accessories is available from your Porter-Cable Factory Service Center or a Porter-Cable Authorized Warranty Service Center. Please visit our Web Site www.portercable.com for a catalog or for the name of your nearest supplier.

WARNING

Do not use any accessory unless you have completely read the Instruction Manual for that accessory.

PARTS LIST

14 IN. (355 MM) BAND SAW

PARTS LIST FOR BAND SAW

I.D. Description Size Qty I.D. Description Size Qty I.D. Description Size Qty

X1RS ADJUSTING KNOB ASSEMBLY 1 X25X COPPER WASHER 2 X405 MICRO ADJUSTING NUT

X1V7 SPRING WASHER

X1VV SCREW (CROSS HEAD)W/I WASHER

X1W2 CROSS HEAD SCREW

X1ZU STEEL BALL

5/16

3/16*3/8

3/16*1/4

1/4

16 X25Y WASHER

11 X25Z FLAT WASHER

3 X262 HEX. SCREW

1 X263 HEX. SCREW

X21A POWER CORD STORAGE 2 X264 PULLEY 3 IN.

X21C HEX. FIXTURE BOLT

3/8

3 X26C SPRING PIN

X21D CLIP HEAD 3 X26L STAR KNOB

3/16-14

3/4

3/4*2-1/2

1/4*3/4

Ø50-Ø76

3*30L

M10

4 X406 NUT

2 X407 SECTOR SCREW

1 X408 SET SCREW

2 X409 SCREW (HEADLESS)

1 X40A HEX. SCREW

1 X40B HEX. SCREW

2 X40C SAFETY SWITCH 1

X21E BLADE GUARD, LOWER 1 X26N HINGE UPPER 1 X40D BALL BEARING 2

X21F BRUSH HOLDER 1 X26T KNOB

X21G STEEL PIN 2 X2D7 SCREW(CROSS HEAD)W/I WASHER

3/8

3/16*1/4

3 X40E POWER CORD W/INSERT PLUG 1

12 X40F GUARD STRONGER 1

X21H HEX. FIXTURE BOLT 2 X2D8 TABLE PIN 1 X40G FRAME ARM COVER, LOWER 1

X21K UPPER WHEEL SHAFT HINGE 1 X2DR HEX. SCREW

X21L SLIDING BKT. 1 X2JS CROSS HEAD SCREW

X21P PIN

1/4*16

4 X2NM BALL BEARING 2 X40K UPPER WHEEL 1

X21Q PRESS SPRING 1 X2PN PLASTIC BRUSH 1 X40L GUIDE SUPPORT BRACKET BLADE

X21R ADJUSTING SPRING 1 X2QG NYLON NUT

ADJUSTING KNOB OF UPPER WHEEL 5/16*2L

X21S

X21U STAR KNOB

X21Z TOOTH WASHER

X221 FLAT WASHER

X224 FLAT WASHER

X225 FLAT WASHER

X227 SPRING WASHER

X228 SQUARE NUT

X229 BUTTERFLY NUT

X22B HEX. NUT

X22C SET SCREW

X22F SET SCREW

X22H CROSS HEAD SCREW

X22K CROSS HEAD SCREW

5/16*1-1/4

5mm

5/16*23

3/8*19

1/4*16

3/4

3/8

5/16

3/4

5/16*5/16

M6*16L

3/16*3/8

1 X2S2 SPRING WASHER

1 X2SU PLATE 2 X40P UPPER COVER, INNER 1

2 X2U7 FLAT KEY

2 X309 BALL BEARING 2 X40R TABLE 1

3 X348 STRAIN RELIEF BUSHING 2 X40S UPPER ARM 1

4 X39J RING 2 X40T PULLEY 7 IN. 1

1 X3ZA SPRING WAHSER

1 X3ZB KNOB

1 X3ZC SCALE OF BLADE GUARD 1 X45M INSTRUCTION MANUAL 1

1 X3ZD WARNING LABEL 1 X4AV FLAT WASHER 1/4*13 6

1 X3ZE WARNING LABEL 1 X4AU SPRING PIN

2 X3ZF MOTOR LABEL 1

2 X3ZG NAMPLATE 1 MOTOR PARTS

9 X3ZH SHAFT OF LOWER WHEEL 1 X1V8 SPRING WASHER 2

5/16*3”

M4*10L

1/2

1/4

5*5*30

3/16

M6*18L

1 X40H FRAME ARM COVER, UPPER 1

1 X40J LOWER WHEEL 1

GUARD

1 X40M LOWER DOOR 1

6 X40N UPPER DOOR 1

1 X40Q TRUNNION BRACKET 1

3 X40U BASE 1

1 X40V COMPLETED MOTOR W/CORD 1

X22S BEARING COVER 1 X3ZJ SHAFT OF UPPER WHEEL 1 X21Z TOOTH WAHSER 5 mm 1

X235 TRUNNION CLAMP SHOE 2 X3ZK TABLE INSERT 1 X23R

SCREW (CROSS HEAD)W/I WASHER

X238 TRUNNION 2 X3ZL GUARD 1 X25X COPPER WAHSER 1

X239 DUST COLLECTION HOSE 1 X3ZM FLAT WASHER FOR LOWER WHEEL 1 X2D7

SCREW (CROSS HEAD)W/I WASHER

X23A SCALE 1 X3ZN BEARING SHAFT 2 X348 STRAIN RELIEF BUSHING 1

X23B HINGE LOWER 1 X3ZP BLADE GUIDE BLOCK 4 X349 TERMINAL 3

X23D POINTER 1 X3ZQ Y TYPE GUIDE ACCESSORY 2 X40Y CROSS HEAD SCREW 3/16*3/16 2

X23F SPRING PIN

X23G FLAT WASHER

X23J HEX.NUT

X23K HEX.NUT

X23L HEX. NUT

X23M HEX. SCREW

X23Q HEX. SCREW

X23R CROSS HEAD SCREW W/I WASHER

X240 HEX. WRENCH

X241 HEX. SCREW

X243 SPRING CLIPPER 3 X402 FLAT WASHER

X244 V-BELT 1 X403 FLAT WASHER

X247 CROSS HEAD SCREW W/WASHER

Ø3*10

5/16*18

5/16

3/16

1/2

5/16*1-1/4

M10*50L

3/16*1/4

3 mm

1/4*1/4

3/16*1/2

1 X3ZR LOWER GUIDE HOLDER 1 X411 CAPACITOR COAST 1

10 X3ZS POST SEAT (DOUBLE TEETH) 1 X417 MOTOR WIRE 1

5 X3ZT CUTTING BLADE

5 X3ZU GUIDE POST (V TYPE)

93-1/2*3/8

243 mm

1 X418 CAPACITOR 1

1 X41C CAPACITOR COVER 1

1 X3ZV WHEEL PROTECTOR 2 X41E WIRE COVER, UPPER 1

6 X3ZW MITER GAUGE ASSY. 1

2 X3ZX KNOB

2 X3ZZ C RING 2 X4AW

1 X400 RING 1 X2DJ

2 X401 FLAT KEY

2 X404 FLAT WASHER

3/8*45L

5*5*60

3/8*16

3/8*25

1/2*28

1 HARDWARE BAG

STAND ATTACHMENT HARDWARE BAG

SAWDUST PORT HARDWARE BAG

2 X2DH

1 X2DK

TRUNNION SUPPORT HARDWARE BAG

POWER CORD STORAGE HARDWARE BAG

3/8

M6*10L

M6*45L

M6*10L

1/4*5/8

1/2*2”

Ø6*20

3/16*1/4 1

3/16*1/4 4

14 IN. (355 MM) BAND SAW

X4AV

X25Z

X3ZF

X40B

X404

X40C

X21H

X23M

X23G

X23J

X3ZL

X22H

X221

X2QG

X2U7

X403

X3ZX

X22S

X3ZZ

X22B

X21P

X227

X1VV

X22F

X264

X40G

X1VV

X2PN

X21F

X40U

X225

X263

X21E

X401

X3ZH

X309

X40T

X3Z

X23G

X23M

X23J

X409

X2DR

X40H

X1VV

X21S

X229

X40E

X2SU

X348

X1VV

X247

X21A

X228

X21Q

X247

X21Z

X25X

X23R

X21A

X21G

X21K

X26C

X3ZJ

X21L

X21R

X3ZR

X405

X262

X3ZS

X408

X1ZU

X409

X407

X409

X3ZB

X3ZN

X40D

X39J

X40S

X21U

X22C

X3ZU

X40M

X22K

X3ZM

X40J

X244

X40Q

X23G

X23M

X238

X235

X1V8

X26L

X22K

X238

X235

X40A

X2S2

X23A

X23D

X23B

X40A

X241

X3ZV

X243

X225

X40R

X23F

X3ZK

X239

X2D8

X3ZD

X1VV

X25Y

X3ZP

X23Q

X40L

X22K

X21H

X3ZT

X23Q

X40K

X25Y

X2NM

X400

X40P

X26N

X2D7

••

X1V7

X23K

X23L

X21C

X21D

X3ZA

X1W2

X26T

X40N

X3ZG

X3ZW

X240

X224

X21C

X21D

X3ZA

X1W2

X224

X40F

X3ZC

X406

X3ZE

X2JS

X402

••

X21C

X21D

X3ZA

X1W2

MANUAL

X45M

INSTRCTION

MOTOR PARTS

X349

• •

X348

X418

X23R

X411

X21Z

X25X

X41D

X417

X2D7

X41E

X2D7

X41C

X1V8

X40Y

X1RS

X4AU

X23M

X23J

X4AW

X2DJ

X2DH

X2DK

X23G

D. Hardware Bag

X241

X239

X225

E. Hardware Bag

F. Hardware Bag

I. Hardware Bag

X23M

X26L

X2DR

X23J

X23G

X21A

X247

X240

X1V7

X22K

X402

X40V

SCHEMATIC FOR BAND SAW

14 IN. (355 MM) BAND SAW

X41N

X41M

X41Q

X41J

X26T

X41H

X41S

X41K

X41L

X2DC

X1VV

X2QE

X41P

X41R

X2UD

X2DS

X2DQ

A. Hardware Bag

B. Hardware Bag

C. Hardware Bag

X2UD

X2DM

X4AX

X4AY

X2DS

X2DC

X1VV

X2DQ

X26T

X2QE

X41J

PARTS LIST AND SCHEMATIC FOR CAB

I.D. Description Size Qty

X1VV SCREW (CROSS HEAD) W/ WASHER 3/16*3/8 8

X26T KNOB 3/8 1

X2DC CARRIAGE SCREW 5/16*1/2 16

X2DM FEET HARDWARE BAG 1

X2DQ HEX. NUT W/WASHER 5/16 16

X2DS PAD 3/8*1 4

X2QE SPRING WAHSER 3/8 1

X2UD HEX. NUT 3/8 4

X41H LABEL 198*68 1

X41J HEX. SCREW 3/8*1/2 1

X41K CROSS HEAD SELF TAPPING SCREW M3 2

X41L MAGNETIC IRON SET 2

X41M RIGHT SIDE COVER PLATE 1

X41N LEFT SIDE COVER PLATE 1

X41P DOOR PLATE 1

X41Q BACK PLATE 1

X41R TOP PLATE 1

X41S TOOL TRAY 1

X4AX STAND HARDWARE BAG 1

X4AY DOOR KNOB HARDWARE BAG

INET STAND

+ 61 hidden pages

Porter-Cable PCB330BS Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual