Porter-Cable PC250MT Instruction Manual

2.5 Amp Oscillating
Multi-Tool

Instruction manual

Manuel d'instructions
Manual de'instrucciones

www.portercable.com
INSTRUCTIVO DE OPERACIÓN,

CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA.

ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.

CATALOG NUMBER

PC250MT

Outil oscillant polyvalent
de 2,5 A

Multiherramienta
oscilante de 2,5 Amperios

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 1

2

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided, may

result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

General Power Tool Safety Warnings

WARNING: Read all safety warnings and instructions. Failure to follow

the warnings and instructions may result in electric shock, fire and/or serious
injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.

1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric

shock.

f) If operating a power tool in a damp location is unavoidable, use a ground

fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the

risk of electric shock.

3) Personal safety
a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 2

3

c) Prevent unintentional starting. Ensure the switch is in the off-position

before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or

energizing power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in
personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust-related hazards.

4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was
designed.

b) Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and must be
repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power toolʼs
operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

5) Service
a) Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Specific Safety Rules

• Disconnect power before using tool near live wires or where there may be

hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the operator an electric shock.” Always
check for hidden wiring, gas lines, or other utilities before performing any material
cutting or removal operations with the tool.

• Hold power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

• Use clamps or another practical way to secure and support the workpiece to a

stable platform. Holding the work by hand or against your body leaves it unstable

and may lead to loss of control.

• Wait for the cutter to stop before setting the tool down. An exposed cutter may

engage the surface leading to possible loss of control and serious injury.

• Do not operate this tool for long periods of time. Vibration caused by the operating

action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 3

4

to provide extra cushion, take frequent rest periods, and limit daily time of use.

• Always hold the tool firmly with both hands for maximum control. Keep proper

footing and balance at all times. This enables better control of the power tool in
unexpected situations.

• Do not restart the cutting operation in the workpiece. Let the tool reach full

speed and carefully re-enter the cut.

• Do not “jam” the cut-off saw blade or apply excessive pressure. Do not

attempt to make an excessive depth of cut.

• Keep your hands away from cutting area. Do not reach under the material being cut.

• Do not use dull or damaged blades. Bent blade can break easily or cause

kickback. Exercise extreme caution when handling the accessories. The
accessories are very sharp. Wear protective gloves when changing cutting
accessories. Accessories become hot after prolonged usage.

• Before scraping, check workpiece for nails. If there are nails, either remove

them or set them well below intended finished surface. Striking a nail with
accessory edge could cause the tool to jump.

• Do not wet sand with this tool. Liquids entering the motor housing are an

electrical shock hazard.

• Never work in area which is soaked with a liquid, such as a solvent or water,

or dampened such as newly applied wallpaper. There is an electrical shock

hazard when working in such conditions with a power tool and heating of the liquid
caused by scraping action may cause harmful vapors to be emitted from workpiece.

• Do not use sandpaper intended for larger sanding pads. Larger sandpaper will

extend beyond the sanding pad causing snagging, tearing of the paper or kick-back.
Extra paper extending beyond the sanding pad can also cause serious lacerations.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety

glasses. Also use face or dust mask. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CPA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the state of California to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products,
arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury. Always use NOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from face
and body.

WARNING: Always wear proper personal hearing protection that conforms

to ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise
from this product may contribute to hearing loss.

Precautions To Take When Sanding Paint

1. Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of
controlling the contaminated dust. The greatest danger of lead poisoning is to children
and pregnant women.

2. Since it is difficult to identify whether or not a paint contains lead without a chemical
analysis, we recommend the following precautions when sanding any paint:

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 4

5

PERSONAL SAFETY

1. No children or pregnant women should enter the work area where the paint

sanding is being done until all clean up is completed.

2. A dust mask or respirator should be worn by all persons entering the work area.

The filter should be replaced daily or whenever the wearer has difficulty breathing.
See your local hardware store for the proper N.I.O.S.H. approved dust mask.

3. NO EATING, DRINKING or SMOKING should be done in the work area to prevent

ingesting contaminated paint particles. Workers should wash and clean up
BEFORE eating, drinking or smoking. Articles of food, drink, or smoking should not
be left in the work area where dust would settle on them.

ENVIRONMENTAL SAFETY

1. Paint should be removed in such a manner as to minimize the amount of dust

generated.

2. Areas where paint removal is occurring should be sealed with plastic sheeting of 4

mils thickness.

3. Sanding should be done in a manner to reduce tracking of paint dust outside the

work area.

CLEANING AND DISPOSAL

1. All surfaces in the work area should be vacuumed and thoroughly cleaned daily for

the duration of the sanding project. Vacuum filter bags should be changed frequently.

2. Plastic drop cloths should be gathered up and disposed of along with any dust

chips or other removal debris. They should be placed in sealed refuse receptacles
and disposed of through regular trash pick-up procedures. During clean up,
children and pregnant women should be kept away from the immediate work area.

3. All toys, washable furniture and utensils used by children should be washed

thoroughly before being used again.

Symbols

• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current

n

o ................no load speed

................Class I Construction ..................earthing terminal

(grounded) ................safety alert symbol

................Class II Construction opm ..............oscillations per minute

(double insulated)

• When using an extension cord, be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The table shows the correct size to use depending
on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gauge
Than Than
0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 5

6

Components

A.) On/Off switch

B.) Variable speed dial

C.) 10 foot cord

D.) Tool-Free accessory change

A

1

B

C

Accessories included:
E.) Kitbox

F.) Wood blade (32mm)

G.) Precision wood blade (32mm)

H.) Wood / Metal blade (32mm)

I.) 1/2 Segment wood / drywall blade

J.) Ridged scraper

K.) Flexible scraper

L.) Carbide grout removal

M.) Sanding platen

N.) Sandpaper

SAVE THESE INSTRUCTIONS

D

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 6

7

INTENDED USE

Detail Sanding

Sanding in extremely tight areas otherwise difficult to reach and require hand sanding.
Select a high oscillating frequency. Sand with continuous motion and light pressure.
Applying excessive pressure does not increase material removal; but will prematurely
wear sanding sheets.

Flush Cutting

Remove excess wood from door jamb, window sill and/or toe kick. Removing excess
copper or PVC pipe.

Removal Work

Carpets & backing, old tile adhesives, caulking on masonry, wood and other surfaces.

Removal of Excess Materials

Tile grout, plaster, mortar splatters, concrete on tiles, sills.

Preparation of Surfaces

New floors and tiles.

ASSEMBLY

WARNING:

Disconnect the plug from the power source before making any
assembly, adjustments or changing accessories. Such preventive safety measures
reduce the risk of starting the tool accidentally.

WARNING: Risk of lacerations or burns. Do not touch workpiece or blade

immediately after operating the tool. They can become very hot. Handle carefully.
Always allow accessories and workpiece to cool before handling.

Installing/Removing Accessories

The PC250MT features an exclusive tool-free accessory changing system. This allows
for faster accessory changes without the need for wrenches or hex keys like other
oscillating tool systems.

• Grasp the tool and squeeze the
accessory clamping lever as shown in
figure 2.

• Clean any residual debris from the tool
shaft and the accessory holder.

2

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 7

• Slide the accessory between the shaft
and the accessory holder making sure
the accessory engages all eight pins on
the holder and is flush with the shaft
(figure 3).

• Release the accessory clamp lever.

• Some accessories, such as scrapers
and blades can be mounted at an angle
if required as shown in figure 4.

Installing/Removing Sanding Sheets - Figure 5

A diamond shaped platen uses a hook
and loop adhesion system to attach the
sanding sheets. The platen allows you
to use it on large flat surfaces and tight
spots or corners.

• Attach the sanding platen as described
under “Installing/Removing
Accessories”.

• Align the edges on the sanding sheet,
with the edge of the sanding platen and
press the sanding sheet onto the platen.

• Firmly press the base with the sanding
sheet attached against a flat surface
and briefly switch the tool on. This
provides for good adhesion between the
platen and the sanding sheet and also
helps to prevent premature wear.

• When the tip of the sanding sheet
becomes worn, detach the sheet from
the platen, rotate and reapply.

8

4

5

3

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 8

9

OPERATION

Switch

CAUTION:

Because the PC250MT has a separate speed dial for setting the
speed (10,000 - 20,000 OPM), the tool will start at the speed where the speed dial is
set. Be sure switch is fully OFF before plugging in the power cord.

• Plug in power cord.

• To turn the tool ON, hold it as shown in
figure 6 and push the slide switch
forward.

• To turn the tool OFF, push the slide
switch backward.

Variable Speed Dial

To operate the tool, select the speed
setting you wish with the speed dial,
shown in figure 7, and slide the ON/OFF
switch forward. The speed setting can be
adjusted either with the tool on or off.

CAUTION: Because the PC250MT

has a separate speed dial for setting the
speed (10,000 - 20,000 OPM), the tool
will start at the speed where the speed
dial is set. Be sure switch is fully OFF
before plugging in the power cord.

The numbered positions,1 through 6
inscribed on the variable speed dial, do
not indicate any precise speed but are
good reference points. The higher the
number, the higher the tool speed.

The approximate speed at each setting is:
SPEED SETTING 1 2 3 4 5 6
APPROXIMATE SPEED 10,000 12,000 14,000 16,000 18,000 20,000
(Actual OPMʼs on your tool may vary.)
Be sure to select the proper speed for your oscillating tool operation. If in doubt about

the proper speed for your operation, test the performance at low speed settings and
gradually increase until a comfortable speed is found.

HELPFUL HINTS

• Always ensure the workpiece is firmly held or clamped to prevent movement. Any
movement of the material may affect the quality of the cutting or sanding finish.

• Do not start sanding without having the sandpaper attached to sanding platen.

• Use coarse grit paper to sand rough surfaces, medium grit for smooth surfaces and
fine grit for the finishing surfaces. If necessary, first make a test run on scrap material.

• Excessive force will reduce the working efficiency and cause motor overload.
Replacing the accessory regularly will maintain optimum working efficiency.

• Do not allow the sandpaper to wear away, it will damage the sanding pad.

• If the tool overheats, especially when used at low speed, set the speed to maximum
and run it with no load for 2-3 minutes to cool the motor. Avoid prolonged usage at
very low speeds. Always keep the blade sharp.

6

7

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 9

10

MAINTENANCE

CAUTION: Never use solvents or other harsh chemicals for cleaning the non-

metallic parts of the tool.
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at
www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory
Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our
Customer Care Center at [phone].

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about
PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our
website at www.portercable.com or call our Customer Care Center at [phone]. All repairs
made by our service centers are fully guaranteed against defective material and workmanship. We
cannot guarantee repairs made or attempted by others.
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,
Tennessee 38305, [phone] - Attention: Product Service. Be sure to include all of the
information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

WARNING: Since accessories, other than those offered by PORTER-CABLE, have

not been tested with this product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only PORTER-CABLE recommended
accessories should be used with this product.

A complete line of accessories is available from your PORTER-CABLE Factory Service
Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our
Web Site www.portercable.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace, without charge, any defects due to faulty
materials or workmanship for three years from the date of purchase for tools (two
years for batteries). This warranty does not cover part failure due to normal wear or
tool abuse. For further detail of warranty coverage and warranty repair information,
visit www.portercable.com or call [phone]. This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you may have other rights
which vary in certain states or provinces.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Cord not plugged in. • Plug tool into a working outlet.

• Circuit fuse is blown. • Replace circuit fuse. (If the
product repeatedly causes the
circuit fuse to blow, discontinue
use immediately and have it
serviced at a Porter Cable
service center or authorized
servicer.)

• Circuit breaker is tripped. • Reset circuit breaker. (If the
product repeatedly causes the
circuit breaker to trip,
discontinue use immediately
and have it serviced at a Porter
Cable service center or
authorized servicer.)

• Cord or switch is damaged. • Have cord or switch replaced
at a Porter Cable Service
Center or Authorized Servicer

For assistance with your product, visit our website at www.portercable.com for a list of
service centers, or call the PorterCable Customer Care Center at [phone].

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 10

11

In addition to the warranty, PORTER-CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn

parts caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performance of your PORTER-CABLE Power Tool for any reason, you can return it
within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific
warranty information contained in the packaging, call the local company or see website
for warranty information.

To register your tool for warranty service visit our website at www.portercable.com

.

WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call [phone] for a free
replacement.

The following are PORTER-CABLE trademarks for one or more power tools and accessories: a
gray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal
stripes. The following are also trademarks for one or more PORTER-CABLE and Delta products:
Les éléments ci-dessous sont des marques de commerce des outils et des accessoires de
PORTER-CABLE : un agencement de couleurs grise et noire; un motif dʼ « étoile à quatre pointes
» et trois bandes longitudinales contrastantes/à contours. Les marques suivantes sont également
des marques de commerce se rapportant à un ou plusieurs produits PORTER-CABLE ou Delta :
Las siguientes son marcas comerciales PORTER-CABLE que distinguen a una o más
herramientas y accesorios: un gráfico de color gris y negro; un diseño de “estrella de cuatro
puntas” y tres franjas longitudinales contrastantes/delineadas. Las siguientes también son marcas
comerciales para uno o más productos de PORTER-CABLE y Delta: 2 BY 4®, 890™, Air
America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders Saw®,
Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's Saw®, Delta®,
DELTA®, Delta Industrial®, DELTA MACHINERY & DESIGN™, Delta Shopmaster and Design®,
Delta X5®, Deltacraft®, DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND DESIGN®,
EASY AIR®, EASY AIR TO GO™, ENDURADIAMOND®, Ex-Cell®, Front Bevel Lock®, Get
Yours While the Sun Shines®, Grip to Fit®, GRIPVAC™, GTF®, HICKORY WOODWORKING®,
Homecraft®, HP FRAMER HIGH PRESSURE®, IMPACT SERIES™, Innovation That Works®,
Jet-Lock®, Job Boss®, Kickstand®, LASERLOC®, LONG-LASTING WORK LIFE®, MAX
FORCE™, MAX LIFE®, Micro-Set®, Midi-Lathe®, Monsoon®, MONSTER-CARBIDE™,
Network®, OLDHAM®, Omnijig®, PC EDGE®, Performance Crew™, Performance Gear®,
Pocket Cutter®, Porta-Band®, Porta-Plane®, PORTER-CABLE®, PORTER-CABLE Professional
Power Tools®, Powerback®, POZI-STOP™, Pressure Wave®, PRO 4000®, Proair®, Quicksand
and Design®, Quickset II®, QUIET DRIVE TECHNOLOGY™, QUIET DRIVE TECHNOLOGY
AND DESIGN™, Quik-Change®, QUIK-TILT®, RAPID-RELEASE™, RAZOR®, Redefining
Performance®, Riptide®, Safe Guard II®, Sand Trap and Design®, Sanding Center®, Saw
Boss®, Shop Boss®, Sidekick®, Site Boss®, Speed-Bloc®, Speedmatic®, Stair Ease®, Steel
Driver Series®, SUPERDUTY®, T4 & DESIGN®, THE AMERICAN WOODSHOP®, THE
PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®, TIGERCLAW®, TIGERCLAW AND
DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®,
UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT
RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR
ACHIEVEMENT. OUR TOOLS.®

Trademarks noted with ® are registered in the United States Patent and Trademark Office and
may also be registered in other countries. Other trademarks may apply. Les marques de
commerce suivies du symbole ® sont enregistrées auprès du United States Patent and
Trademark Office et peuvent être enregistrées dans dʼautres pays. Dʼautres marques de
commerce peuvent également être applicables. Las marcas comerciales con el símbolo ® están
registradas en la Oficina de patentes y marcas comerciales de Estados Unidos (United States
Patent and Trademark Office), y también pueden estar registradas en otros países. Posiblemente
se apliquen otras marcas comerciales registradas.

4825 Highway 45

North Jackson, TN 38305

[phone]

www.portercable.com

90571150 PC250MT REVISED OScillating Tool*.qxd:??????-00 Cir Saw book 1/14/11 11:31 AM Page 11