Porter-Cable PC1800DS, 90550099 User Manual

Cordless Detail Sander

www.portercable.com

INSTRUCTIVO DE OPERACIÓN,
CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA.

ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.

CATALOG NUMBER

PC1800DS

Ponceuse pour travaux
détaillés

Lijadora inalámbrica para
detalles

Instruction manual

Manuel d'instructions
Manual de'instrucciones

Batteries and chargers sold separately

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 1

2

General Power Tool Safety Warnings

Read all safety warnings and instructions. Failure to follow

the warnings and instructions may result in electric shock, fire and/or serious
injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust. Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric

shock.

f) If operating a power tool in a damp location is unavoidable, use a ground

fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the

risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energising power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in
personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust-related hazards.

:

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 2

3

4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was
designed.

b) Do not use the power tool if the switch does not turn it on and off. Any

power tool that cannot be controlled with the switch is dangerous and must be
repaired.

c) Disconnect the plug from the power source and/or the battery pack from

the power tool before making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended

could result in a hazardous situation.

5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that

is suitable for one type of battery pack may create a risk of fire when used with
another battery pack.

b) Use power tools only with specifically designated battery packs. Use of any

other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another. Shorting the battery

terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid

contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may

cause irritation or burns.

6) Service
a) Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power tool is

maintained.

SPECIFIC SAFETY RULES

• Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a

"live" wire will make exposed metal parts of the tool "live" and shock the operator.

• When working on a ladder or on scaffolding be sure to lay the tool down on its

side when not in use. Some tools with large battery packs will stand upright but may
be easily knocked over.

• Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and
may lead to loss of control.

ALWAYS use safety glasses. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if drilling operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CPA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

:

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 3

4

Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the state of California to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

Use of this tool can generate and/or disperse dust, which may cause
serious and permanent respiratory or other injury. Always use NOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles away
from face and body.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

• When using an extension cord, be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a drop in line voltage resulting in
loss of power and overheating. The following table shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier the cord.

:

:

:::

:

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gage
Than Than
0-6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 4

5

Symbols

• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current

n

o ................no load speed

................Class I Construction ..................earthing terminal

(grounded) ................safety alert symbol

................Class II Construction .../min or rpm...revolutions or

(double insulated) reciprocation per minute

sfpm ............surface feet per minute

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for

battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery
pack, and product using battery pack.

Shock hazard. Do not allow any liquid to get inside charger.

Burn hazard. To reduce the risk of injury, charge only designated

PORTER-CABLE batteries. Other types of batteries may burst causing personal injury
and damage.

Under certain conditions, with the charger plugged in to the power

:

:

:

LI-ION Battery Packs and Chargers

Battery: LI-ION 18V

Charger: LI-ION

PC18BL

PC18BLX

PC18BLEX

PCLMVC

PCXMVC

Description Cat. #

NI-CD Battery Packs and Chargers

This product can accept any of the batteries and chargers listed in the chart below.

Battery: NI-CD 18V
Charger: NI-CD

PC18B

PCMVC

PCXMVC

Description Cat. #

FUNCTIONAL DESCRIPTION

1. On/Off Switch

2. Sanding Base

3. Vacuum Port

4. Battery Compartment

5. Finger Attachment

6. Vacuum Port Adaptor

1

2

3

4

A

6

5

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 5

supply, the charger can be shorted by foreign material. Foreign materials of a
conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup
of metallic particles should be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery pack in the cavity. Unplug
charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any chargers other than the

ones in this manual. The charger and battery pack are specifically designed to
work together.

• These chargers are not intended for any uses other than charging designated

PORTER-CABLE rechargeable batteries. Any other uses may result in risk of fire,
electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk

of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over,

or otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper

extension cord could result in risk of fire, electric shock, or electrocution.

• An extension cord must have adequate wire size (AWG or American Wire

Gauge) for safety. The smaller the gauge number of the wire, the greater the

capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When
using more than one extension to make up the total length, be sure each individual
extension contains at least the minimum wire size.

• Do not place any object on top of charger or place the charger on a soft

surface that might block the ventilation slots and result in excessive internal
heat. Place the charger in a position away from any heat source. The charger is

ventilated through slots in the top and the bottom of the housing.

• Do not mount charger on wall or permanently affix charger to any surface. The

charger is intended to use on a flat, stable surface (i.e., table top, bench top).

• Do not operate charger with damaged cord or plug — have them replaced

immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way. Take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service

or repair is required. Incorrect reassembly may result in a risk of electric shock,
electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This

will reduce the risk of electric shock. Removing the battery pack will not reduce this
risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard household electrical power

(120 Volts). Do not attempt to use it on any other voltage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION FOR BATTERY PACKS

For safe operation, read this manual and manuals originally supplied

with tool before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack
and charger, read the safety instructions below. Then follow charging procedures
outlined.

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack even if it is severely damaged or is

completely worn out. The battery pack can explode in a fire. Toxic fumes and

materials are created when LI-ION battery packs are burned.

• Do not charge or use battery in explosive atmospheres, such as in the presence

of flammable liquids, gases or dust. Inserting or removing the battery from the

charger may ignite the dust or fumes.

• If battery contents come into contact with the skin, immediately wash area with

mild soap and water. If battery liquid gets into the eye, rinse water over the open eye

:

6

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 6

7

for 15 minutes or until irritation ceases. If medical attention is needed, the battery
electrolyte for LI-ION batteries is composed of a mixture of liquid organic carbonates
and lithium salts. For NI-Cd batteries it is a 25-35% solution of potassium hydroxide.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh
air. If symptoms persists, seek medical attention.

Burn hazard. Battery liquid may be flammable if exposed to spark or

flame.

• Charge the battery packs only in PORTER-CABLE chargers.

• DO NOT splash or immerse in water or other liquids. This may cause premature

cell failure.

• Do not store or use the tool and battery pack in locations where the
temperature may reach or exceed 105°F (40˚C) (such as outside sheds or metal
buildings in summer).

Never attempt to open the battery pack for any reason. If battery pack
case is cracked or damaged, do not insert into charger. Do not crush, drop or damage
battery pack. Do not use a battery pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,
stepped on). Damaged battery packs should be returned to service center for recycling.

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the
battery is out of the tool or charger. Remove cap before placing battery in
charger or tool.

Fire hazard. Do not store or carry battery so that metal objects can
contact exposed battery terminals. For example, do not place battery in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals
inadvertently come in contact with conductive materials such as keys, coins, hand
tools and the like. The US Department of Transportation Hazardous Material

Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes
(i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected
from short circuits. So when transporting individual batteries, make sure that the battery
terminals are protected and well insulated from materials that could contact them and
cause a short circuit. NOTE: LI-ION batteries should not be put in checked baggage.

STORAGE RECOMMENDATIONS

1. The best storage place is one that is cool and dry away from direct sunlight and
excess heat or cold.

2. Long storage will not harm the battery pack or charger. Under proper conditions
LI-ION batteries, can be stored for 5 years or more.

CHARGING PROCEDURE
PORTER-CABLE chargers are designed to charge PORTER-CABLE battery packs in

30-60 minutes depending on the pack being charged.

1. Plug the charger into an appropriate outlet before
inserting the battery pack.

2. Insert the battery pack into the charger

(figure B).

:::

Battery Cap

B

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 7

3. The LED will flash indicating that the battery is being charged.

4. The completion of charge is indicated by the LED remaining on continuously.
The pack is fully charged and may be used at this time or left on the charger.

CHARGER DIAGNOSTICS

This charger is designed to detect certain problems that can arise with the battery packs or
the power source. Problems are indicated by one LED flashing in different patterns.

BAD BATTERY

The charger can detect a weak or damaged battery. The LED flashes in the pattern
indicated on the label. If you see this bad battery blink pattern, do not continue to
charge the battery. Return it to a service center or a collection site for recycling.

HOT/COLD PACK DELAY

When the charger detects a battery that is excessively hot or excessively cold, it
automatically starts a Hot/Cold Pack Delay, suspending charging until the battery
has normalized. After this happens, the charger automatically switches to the
Pack Charging mode. This feature ensures maximum battery life. The light
flashes in the pattern indicated on the label.

PROBLEM POWER LINE

When the charger is used with some portable power sources such as generators
or sources that convert DC to AC, the charger may temporarily suspend
operation. The LED flashes in the pattern indicated on the label. This indicates
that the power source is out of limits.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected with the LED glowing indefinitely.
The charger will keep the battery pack fresh and fully charged. This charger features
an automatic tune-up mode which equals or balances the individual cells in the battery pack
to allow it to function at peak capacity. Battery packs should be tuned up weekly or
whenever the battery no longer delivers the same amount of work. To use the automatic
tune-up mode, place the battery pack in the charger and leave it for at least 8 hours.

IMPORTANT CHARGING NOTES

1. Longest life and best performance can be obtained if the battery pack is charged
when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).
This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a
normal condition, and does not indicate a problem. To facilitate the cooling of the
battery pack after use, avoid placing the charger or battery pack in a warm
environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp or other appliance
b. Check to see if receptacle is connected to a light switch which turns power off
when you turn out the lights.
c. Move charger and battery pack to a location where the surrounding air
temperature is approximately 65°F - 75°F (18°- 24°C).
d. If charging problems persist, take the tool, battery pack and charger to your
local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on

jobs which were easily done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also charge a partially used pack
whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool,

aluminum foil, or any buildup of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply when there is no battery
pack in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

Shock hazard. Do not allow any liquid to get inside charger.

Never attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a service center for recycling.

:

:

8

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 8

9

Safety Warnings and Instructions: Sanders

• ALWAYS WEAR EYE AND RESPIRATORY PROTECTION.

• Clean your tool out periodically.

Other Important Safety Warnings and Instructions

Sanding

Lead based paint

Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling
the contaminated dust. The greatest danger of lead poisoning is to children and
pregnant women.

Since it is difficult to identify whether or not a paint contains lead without a chemical
analysis, we recommend the following precautions when sanding any paint:

Personal safety

• No children or pregnant women should enter the work area where the paint sanding is
being done until all clean up is completed.

• A dust mask or respirator should be worn by all persons entering the work area. The
filter should be replaced daily or whenever the wearer has difficulty breathing.

NOTE: Only those dust masks suitable for working with lead paint dust and fumes
should be used. Ordinary painting masks do not offer this protection. See your local
hardware dealer for the proper (NIOSH approved) mask.

• NO EATING, DRINKING or SMOKING should be done in the work area to prevent
ingesting contaminated paint particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the
work area where dust would settle on them.

Environmental safety

• Paint should be removed in such a manner as to minimize the amount of dust
generated.

• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils
thickness.

• Sanding should be done in a manner to reduce tracking of paint dust outside the work
area.

Cleaning and disposal

• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the
duration of the sanding project. Vacuum filter bags should be changed frequently.

• Plastic drop cloths should be gathered up and disposed of along with any dust chips or
other removal debris. They should be placed in sealed refuse receptacles and
disposed of through regular trash pick-up procedures. During clean up, children and
pregnant women should be kept away from the immediate work area.

• All toys, washable furniture and utensils used by children should be washed thoroughly
before being used again.

INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL

Make certain the switch is off to prevent switch actuation before removing

or installing battery.

TO INSTALL BATTERY PACK: Insert battery pack
into tool as shown in figure C.

:

C

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 9

10

TO REMOVE BATTERY PACK: Depress the battery
release button as shown in figure D and pull battery
pack out of tool.

Operating Instructions

To reduce the risk of serious personal injury, read and follow all important

safety warnings and instructions prior to using this tool.

Switch

To turn the tool ON, hold it as shown in figure E and push the portion of the switch
marked "I". To turn the tool OFF, push the portion of the switch marked "O".

Operation (Figure E)

Grasp product as shown in figure E and turn it on.
NOTE: Do not rest fingers on platen during use.

Move it in long sweeping strokes across the surface,
letting it do the work. Light pressure is all that is
required for sanding. Excessive pressure will slow the
tool and produce inferior results. Check your work
often, product is capable of removing material rapidly.

Shock hazard. Under no circumstances should this product be used near

water.

To reduce the risk of injury, turn off and remove battery from the tool

before making any adjustments or removing or installing attachments or accessories.

Detail Sanding

Your tool is equipped with a teardrop base which allows you to use it on large flat surfaces
and tight spots or corners.

The pad tips may wear unevenly, depending on use. The pads are designed to allow you
to interchange and /or rotate the diamond tip.

Fitting sanding sheets (figure F)

• Detach the two diamond-shaped tips from the
sanding sheet.

• Hold the tool with the sanding base facing upwards.

• Place the sanding sheet onto the sanding base.
The diamond-shaped tip can be reversed and

replaced when worn.

• When the front part of the tip is worn, detach it from
the sheet, reverse it and press it onto the sanding
base again.

• When the whole tip is worn, remove it from the
sanding base and fit a new tip.

:

:

D

E

:

F

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 10

11

Tip of the Sanding Base (figure G)

• When the sanding base tip is worn, it can be
reversed or replaced.

• Reverse or replace the worn part.

Finger Attachment (figure H)

The finger attachment is used for fine detail
sanding.

• Remove the screw.

• Remove the diamond-shaped tip holder from the
sanding base.

• Fit the finger attachment onto the sanding base.

• Fit and tighten the screw.

• Align the sanding sheet with the finger attachment.

Dust Collection / Vacuum Port Adaptor
(figure I)

A vacuum hose can be attached to the sander to
allow for dust collection.

Fire hazard. Collected sanding dust from sanding surface coatings
(polyurethane, linseed oil, etc.) can self-ignite in sander dust canister or elsewhere and
cause fire. To reduce risk, empty canister frequently and strictly follow sander manual and
coating manufacturer's instructions.

Fire hazard. When working on metal surfaces, do not use a vacuum cleaner
because sparks are generated. Wear safety glasses and a dustmask. Due to the danger
of fire, do not use your sander to sand magnesium surfaces. Do not use for wet sanding.

Hints for optimum use

• Do not place your hands over the ventilation slots.

• Do not exert too much pressure on the tool.

• Regularly check the condition of the sanding sheet. Replace when necessary.

• Always sand with the grain of the wood.

• When sanding new layers of paint before applying another layer, use extra fine grit.

• On very uneven surfaces, or when removing layers of paint, start with a coarse grit.
On other surfaces, start with a medium grit. In both cases, gradually change to a fine
grit for a smooth finish.

:

:

G

H

I

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 11

12

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
LI-ION or NI-CD battery (or battery pack) indicates that the costs to recycle the
battery (or battery pack) at the end of its useful life have already been paid by
PORTER-CABLE.
RBRC™ in cooperation with PORTER-CABLE and other battery users, has
established programs in the United States to facilitate the collection of spent
LI-ION or NI-CD batteries. Help protect our environment and conserve natural
resources by returning the spent LI-ION or NI-CD battery to an authorized
PORTER-CABLE service center or to your local retailer for recycling. You may also
contact your local recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at
www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory
Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our
Customer Care Center at [phone].

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about
PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our
website at www.portercable.com or call our Customer Care Center at [phone]. All repairs
made by our service centers are fully guaranteed against defective material and workmanship. We
cannot guarantee repairs made or attempted by others.
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,
Tennessee 38305, [phone] - Attention: Product Service. Be sure to include all of the
information shown on the nameplate of your tool (model number, type, serial number, etc.).

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Battery pack not installed properly. • Check battery pack
installation.

• Battery pack not charged. • Check battery pack
charging requirements.

• Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into
charger until LED
appears.

• Charger not plugged in. • Plug charger into a
working outlet. Refer to
“Important Charging Notes”
for more details.

• Surrounding air temperature • Move charger and battery

too hot or too cold. pack to a surrounding air

temperature of above 40
degrees F (4,5°C) or below
105 degrees F (+40,5°C).

SPECIAL NOTES FOR USE WITH LITHIUM BATTERIES

• Unit shuts off abruptly. • Battery pack has reached its • Allow battery pack to cool
maximum thermal limit. down.

• Out of charge. ( To • Place on charger and

maximize the life of the allow to charge.
battery pack it is designed
to shutoff abruptly when
the charge is depleted.)

For assistance with your product, visit our website at www.portercable.com for a list of service
centers, or call the PORTER-CABLE Customer Care Center at [phone].

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 12

13

ACCESSORIES

Since accessories, other than those offered by PORTER-CABLE, have
not been tested with this product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only PORTER-CABLE recommended
accessories should be used with this product.

A complete line of accessories is available from your PORTER-CABLE Factory Service
Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our
Web Site www.portercable.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace, without charge, any defects due to faulty
materials or workmanship for three years from the date of purchase for tools (two
years for batteries). This warranty does not cover part failure due to normal wear or
tool abuse. For further detail of warranty coverage and warranty repair information,
visit www

.portercable.com or call [phone]. This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and you may have other rights
which vary in certain states or provinces.

In addition to the warranty, PORTER-CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn

parts caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performance of your PORTER-CABLE Power Tool for any reason, you can return it
within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained in
the packaging, call the local company or see website for warranty information.

To register your tool for warranty service visit our website at www

.portercable.com.

W

ARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call [phone] for a free
replacement.

The following are PORTER-CABLE trademarks for one or more power tools and accessories: a
gray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal
stripes. The following are also trademarks for one or more PORTER-CABLE and Delta products: 2
BY 4®, 890™, Air America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®,
Builders Saw®, Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's
Saw®, Delta®, DELTA®, Delta Industrial®, DELTA MACHINERY & DESIGN™, Delta Shopmaster
and Design®, Delta X5®, Deltacraft®, DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND
DESIGN®, EASY AIR®, EASYAIR TO GO™, ENDURADIAMOND®, Ex-Cell®, Front Bevel
Lock®, Get Yours While the Sun Shines®, Grip to Fit®, GRIPVAC™, GTF®, HICKORY
WOODWORKING®, Homecraft®, HP FRAMER HIGH PRESSURE®, IMPACT SERIES™,
Innovation That Works®, Jet-Lock®, Job Boss®, Kickstand®, LASERLOC®, LONG-LASTING
WORK LIFE®, MAX FORCE™, MAX LIFE®, Micro-Set®, Midi-Lathe®, Monsoon®, MONSTER­CARBIDE™, Network®, OLDHAM®, Omnijig®, PC EDGE®, Performance Crew™, Performance
Gear®, Pocket Cutter®, Porta-Band®, Porta-Plane®, PORTER-CABLE®, PORTER-CABLE
Professional Power Tools®, Powerback®, POZI-STOP™, Pressure Wave®, PRO 4000®,
Proair®, Quicksand and Design®, Quickset II®, QUIET DRIVE TECHNOLOGY™, QUIET DRIVE
TECHNOLOGY AND DESIGN™, Quik-Change®, QUIK-TILT®, RAPID-RELEASE™, RAZOR®,
Redefining Performance®, Riptide®, Safe Guard II®, Sand Trap and Design®, Sanding Center®,
Saw Boss®, Shop Boss®, Sidekick®, Site Boss®, Speed-Bloc®, Speedmatic®, Stair Ease®,
Steel Driver Series®, SUPERDUTY®, T4 & DESIGN®, THE AMERICAN WOODSHOP®, THE
PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®, TIGERCLAW®, TIGERCLAW AND
DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®,
UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT
RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR
ACHIEVEMENT. OUR TOOLS.®

Trademarks noted with ® are registered in the United States Patent and Trademark Office and
may also be registered in other countries. Other trademarks may apply.

4825 Highway 45 North

Jackson, Tennessee 38305

[phone] www.portercable.com

:

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 13

14

Manuel d'instructions

www.portercable.com

Ponceuse pour
travaux détaillés

N° DE CATALOGUE

PC1800DS

Blocs-piles et chargeurs vendus séparément

90550099 PC1800DS Crdl Sander REVISED 4/1/09 1:52 PM Page 14