Porter-Cable PC1500HGA, PC1500HG Instruction Manual
Two Speed Variable
Temperature Heat Gun
Instruction manual
Manuel d'instructions
Manual de'instrucciones
www.portercable.com
INSTRUCTIVO DE OPERACIÓN,
CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA.
ADVERTENCIA: LÉASE ESTE
INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
CATALOG
NUMBERS
PC1500HG,
PC1500HGA
Pistolet thermique à
température variable et à
deux vitesses
Pistola de calor de dos
velocidades y
temperatura variable
Important Safety Warnings and Instructions
WARNING: When using electric tools, basic safety precautions should always be
followed to reduce risk of fire, electric shock, and personal injury, including the following.
READ ALL INSTRUCTIONS
TO REDUCE RISK OF INJURY:
• Before any use, be sure everyone using this tool reads and understands all safety
instructions and other information contained in this manual.
• Save these instructions and review frequently prior to use and in instructing others.
General Safety Warnings and Instructions for All Tools
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• CONSIDER WORK AREA ENVIRONMENT. Donʼt expose power tools to rain. Donʼt use
power tools in damp or wet locations. Keep work area well lit. Do not use in presence of
flammable liquids or gases. Motors in these tools normally spark, and the sparks may
ignite the fumes.
• GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces.
For example; pipes, radiators, ranges, refrigerator enclosures. Use extreme caution when
drilling, driving, or cutting into walls, floors, ceilings or other areas or wherever live
electrical wires may be contacted, do not touch any metal parts of the tool. Hold the tools
only by the plastic handle to prevent electric shock.
• KEEP CHILDREN AWAY. Do not let children and visitors contact tool or extension cord.
All children and visitors should be kept away from work area.
• STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-
up place–out of reach of children.
• DONʼT FORCE TOOL. It will do the job better and safer at the rate for which it was
intended.
• USE RIGHT TOOL. Donʼt force small tool or attachment to do the job of a heavy-duty
tool. Donʼt use tool for purposes not intended.
• DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in
moving parts. Heavy duty gloves to protect hands and non-skid footwear are
recommended when working outdoors. Wear protective hair covering to contain long hair.
• USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or
safety glasses with side shields, complying with applicable safety standards and, when
needed, a face shield. Also use face or dust mask if cutting operation is dusty. This
applies to all persons in the work area. Also use a hard hat, hearing protection, gloves,
safety shoes and dust collection systems when specified or required.
• DONʼT ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
• SECURE WORK. Use clamps or a vise to hold work. Itʼs safer than using your hand and it
frees both hands to operate tool.
• DONʼT OVERREACH. Keep proper footing and balance at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect tool
cords periodically and if damaged, have repaired by authorized service facility. Inspect
extension cords periodically and replace if damaged. Keep handles dry, clean, and free
from oil and grease.
• DISCONNECT TOOLS. Unplug the tool when not in use, when moving tool from place to
place, before servicing, and when changing accessories (such as blades, bits, cutters) or
making adjustments.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that
keys and adjusting wrenches are removed from tool before turning it on.
• AVOID UNINTENTIONAL STARTING. Donʼt carry tool with finger on switch. Be sure
switch is off when plugging in.
• OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
• STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when
you are tired or otherwise impaired.
2
3
• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and
perform its intended function. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or replaced by an
authorized service center. Do not use tool if switch does not turn it on and off.
• REPAIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in
this manual should be performed by Porter Cable authorized service centers or other
qualified service organizations, always using identical replacement parts.
• USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or
attachment not recommended for use with the tool could be hazardous. Note: Refer to the
accessory section of this manual for further details.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual.
The information it contains relates to protecting YOUR SAFETY and PREVENTING
PROBLEMS. The symbols below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION: Used without the safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in property damage.
Additional Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS FOR HEAT GUNS
1. Remember that hidden areas such as those behind walls, ceilings, floors, soffit boards
and other panels may contain flammable materials that could be accidentally ignited
when stripping paint from the panel. Such a fire would not be readily apparent, and could
cause considerable damage and danger of injury. This heat gun is capable of producing
temperatures in excess of 1000° F (538° C).
2. Do not use this tool as a hair dryer.
3. Always turn heat gun off, disconnect from power source and let the tool cool down for at
least 30 minutes before moving or storing it. Do not lay the heat gun on flammable
surfaces when operating the gun or immediately after shutting it off. Always set the gun
on a flat level surface so that the nozzle tip is pointed upward when allowing to cool.
For easy storage, the tool can hang from the hang hole. The heat gun should be stored
indoors.
4. Always use good quality scrapers and stripping knives.
5. Never obstruct the air intake or nozzle outlet.
6. Be sure to direct the hot air blast in a safe direction; away from other people or flammable
objects.
7. Keep fingers away from metal nozzle; it becomes very hot.
8. Donʼt touch the nozzle to any surface while running or shortly after running.
9. Avoid poking anything down inside the nozzle.
10. Know your work environment. Remember that areas behind soffit board, ceilings, and
floors may contain highly flammable materials. Check these areas before applying heat.
11. Clean dry paint from the nozzle after use; it could ignite.
12. Clean your scraper blade frequently during use; it could ignite.
13. Do not use the heat gun in combination with chemical strippers.
14. Do not use accessory nozzles as scrapers.
15. Keep nozzle away from cord.
16. Do not use to cook or warm food.
17. Be constantly aware that this tool can ignite flammable materials, and soften or melt
others. Regardless of the task you are performing, shield or keep away from these
materials that are close to the work area.
You may occasionally notice some slight smoking of the tool after it is turned off. This is the
result of heating the residual oil that was deposited on the heating element during the
manufacturing process.
IMPORTANT NOTICE:
In order for this tool to be an effective paint stripper, it must produce extremely high
temperatures. As a consequence, the stripper is capable of igniting paper, wood, paint and
varnish residue and similar materials.
As you become more familiar with the tool and develop the proper technique, the danger of
accidental ignition will be greatly reduced. In establishing the proper technique, the best thing
to do is practice! Work on simple stripping projects, preferably outdoors, until you get a “feel”
for how to use your stripper safely and effectively.
As you practice, observe the following procedures for safety:
1. Always be sure the tool is turned off and disconnected from power supply when unattended.
2. Clean the scraper blade often during use. Built up residue on the blade is highly
flammable.
3. Experiment to find the optimum distance from the toolʼs nozzle to the surface being
stripped. This distance (usually 1-2 inches)(25-50 mm) will vary depending on the
material being removed.
4. Keep the heat gun moving ahead of the scraper blade at all times.
5. As you work, clean up loose pieces of paint as they accumulate around the work area.
6. When working indoors, keep away from curtains, papers, upholstery and similar
flammable materials.
7. Above all, remember that this is a serious power tool that is capable of producing
excellent results when used properly. Practice on simple projects until you feel
comfortable with your stripper. Only then will you have mastered the proper technique.
WARNING: Extreme care should be taken when stripping paint. The peelings, residue
and vapors of paint may contain lead, which is poisonous.Any pre-1977 paint may contain
lead and paint applied to homes prior to 1950 is likely to contain lead. Once deposited on
surfaces, hand to mouth contact can result in the ingestion of lead. Exposures to even low
levels of lead can cause irreversible brain and nervous system damage; young and unborn
children are particularly vulnerable.
Before beginning any paint removal process you should determine whether the paint you are
removing contains lead. This can be done by your local health department or by a
professional who uses a paint analyzer to check the lead content of the paint to be removed.
Lead based paint should only be removed by a professional and should not be
removed using a heat gun.
Persons removing paint should always follow these guidelines:
1. Move the work piece outdoors. If this is not possible, keep the work area well ventilated.
Open the windows and put an exhaust fan in one of them. Be sure the fan is moving the
air from inside to outside.
2. Remove or cover any carpets, rugs, furniture, cooking utensils, and air ducts.
3. Place drop cloths in the work area to catch any paint chips or peelings. Wear protective
clothing such as extra work shirts, overalls and hats.
4. Work in one room at a time. Furnishings should be removed or placed in the center of the
room and covered. Work areas should be sealed off from the rest of the dwelling by
sealing doorways with drop cloths.
4
5
5. Children, pregnant women or potentially pregnant women and nursing mothers should
not be present in the work area until the work is done and all clean up is complete.
6. Wear a dust respirator mask or a dual filter (dust and fume) respirator mask which has
been approved by the Occupational Safety and Health Administration (OSHA), the
National Institute of Safety and Health (NIOSH), or the United States Bureau of Mines.
These masks and replaceable filters are readily available at major hardware stores. Be
sure the mask fits. Beards and facial hair may keep masks from sealing properly. Change
filters often. Disposable paper masks are not adequate.
7. Use caution when operating the heat gun. Keep the heat gun moving as excessive heat
will generate fumes which can be inhaled by the operator.
8. Keep food and drink out of the work area. Wash hands, arms and face and rinse mouth
before eating or drinking. Do not smoke or chew gum or tobacco in the work area.
9. Clean up all removed paint and dust by wet mopping the floors. Use a wet cloth to clean
all walls, sills and any other surface where paint or dust is clinging. Do not sweep, dry dust
or vacuum. Use a high phosphate detergent or trisodium phosphate (TSP) to wash and
mop areas.
10.At the end of each work session put the paint chips and debris in a double plastic bag,
close it with tape or twist ties, and dispose of properly.
11.Remove protective clothing and work shoes in the work area to avoid carrying dust into
the rest of the dwelling. Wash work clothes separately. Wipe shoes off with a wet rag that
is then washed with the work clothes. Wash hair and body thoroughly with soap and water.
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min........................minutes ......................alternating
current
......................direct current
n
o ........................no load speed
..........................
Class II Construction
........................earthing terminal
........................safety alert symbol .../min ..................revolutions or
reciprocations per minute
WARNING: Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the
skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may
cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA
approved respiratory protection appropriate for the dust exposure. Direct particles
away from face and body.
WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty.
ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• ANSI S12.6 (S3.19) hearing protection
• NIOSH/OSHA/MSHA respiratory protection
6
U
SE OF EXTENSION CORDS
Make sure the extension cord is in good condition before using. Always use the proper
size extension cords with the tool – that is, proper wire size for various lengths of cord and
heavy enough to carry the current the tool will draw. Use of an undersized cord will cause
a drop in line voltage resulting in loss of power and overheating. For proper size cords see
chart below.
MOTOR
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means
your tool will operate on standard 60 Hz household power. Do not operate AC tools on
DC. A rating of 120 voltsAC/DC means that you tool will operate on standard 60 Hz AC or
DC power. This information is printed on the nameplate. Lower voltage will cause loss of
power and can result in over-heating. All Porter Cable tools are factory-tested; if this tool
does not operate, check the power supply.
Tool Operation
SWITCH - FIGURE B
The position of the switch controls both the fan speed and the heat output of the gun.
There is considerable overlap in the temperature ranges with the use of the temperature
adjustment knob.
• To turn the tool on in low air speed, low heat, slide the switch (1)
to the position marked “I”.
• To turn the tool on in high air speed, high heat , slide the switch
(1) to the position marked “II”.
• To turn the tool off, slide the switch (1) to the position marked “0”.
Minimum Gauge for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V 0-50 51-100 101-200 201-300
(0-15,2m) (15,2-30,4m)(30,4-60,9m) (60,9-91,4m)
Ampere Rating
More Not more American Wire Gage
Than Than
0-6 18 16 16 14
6-10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
FUNCTIONAL DESCRIPTION
1. Two speed switch
2. Hang hole
3. Air vents
4. Hot air nozzle
5. Temperature adjustment knob
1
2
4
A
B
5
3
1
7
TEMPERATURE ADJUSTMENT KNOB FIGURE C
• To raise the air temperature, turn the
knob (5) clockwise.
• To lower the air temperature turn the
knob (5) counterclockwise.
REMOVING PAINT - FIGURE D
Efficient paint removal requires the
development of technique. Follow the
guidelines in this manual and youʼll find
that you will have mastered the procedure
after a few simple projects.
Turn on the tool and hold the nozzle
about one inch (25mm) from the surface
to be stripped, as shown in figure D.
(Give the unit about 15-20 seconds
running time to reach its full heat
potential.) The paint being heated will
usually begin to blister when it reaches
the proper temperature for stripping.
When it reaches this point begin scraping
with smooth, even strokes. If the paint is
sufficiently hot and the scraper is properly
suited to the surface being stripped, the
paint should come off in a strip equal to
the full width of the scraper. Move the unit
slightly ahead of the scraper to assure
that the paint being stripped is softened.
Best results will be achieved if the heat
gun is moved slowly, but constantly, from
side to side to evenly distribute heat. Do
not linger or pause in one spot.
Remember that splinters and small
particles of stripped paint can be ignited
and blown through holes and cracks in
the surface being stripped.
HINTS ABOUT PAINT STRIPPING
A smooth, downward scraping action will give good results and will help to prevent
gouging the work surface.
With some paints, prolonged heating will actually make them tougher to strip. Try a few
different heating times until you develop the technique best suited to your particular
application.
The heat gun is designed to remove both oil based and latex based paints.
It will not remove stains or primer coats that have impregnated the wood grain.
Scrape paint as soon as it softens, it will soon cool and harden again. Clean the edge of
your scraper often to retain a clean, sharp edge. Shield areas adjacent to where youʼre
scraping. For example: shield the door with nonflammable materials if youʼre stripping the
door frame.
Donʼt concentrate the tools heat on a window pane or other glass surface. Excessive heat
may crack the glass. Use some nonflammable material to shield the glass when stripping
the window frame.
OTHER USES
For hands free operation, place the heat gun on a flat surface as shown in figure E.
Aside from stripping paint, your heat gun has a wide array of other uses. Use it for
softening linoleum and floor tile and for loosening heat sensitive adhesives. Itʼs perfect for
use with heat shrinkable tubing and anywhere you need a portable heat source. You can
even use it to thaw frozen metal water pipes.
D
C
5
8
A
utomotive uses include reducing set up
t
ime on body fillers or drying time on paints
(the product manufacturerʼs
recommendations must be followed.)
Caution must be exercised around
gasoline, automotive fluids, tires, gaskets,
upholstery and hoses, etc. to prevent
damage or fires. Be constantly aware that
this tool can ignite flammable materials
and soften or melt others. Avoid
overheating adjacent flammable materials
such as wood, insulation, electrical wiring
jackets or plastic. Thaw only those metal
pipe sections that are fully exposed. Do
not attempt to thaw pipes that are inside
walls, floors, ceilings, or otherwise
enclosed. Do not attempt to thaw pipes
that are wrapped in insulation.
ACCESSORIES
WARNING: The use of any accessory
not recommended for use with this tool could be hazardous.Always unplug the tool before
attaching or removing accessories. Do not remove accessory tips until the tool has cooled
to room temperature.
The following attachments are included with the PC1500HGA Heat Gun.
E
FAN NOZZLE
Wider distribution of the hot air, for working on
large surfaces- floors, doors, etc.
GLASS PROTECTOR
Safer working near glass. Distributes heat away
from area to be protected.
CONE NOZZLE
For precise operations- concentrates the air onto a
smaller surface area.
SPOOL REFLECTOR
Evenly dispenses air around whole object. Ideal for
soldering pipework, shrink sealing electrical cable.
CAUTION: These nozzles remain hot after use. Use care in handling them.
9
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE POSSIBLESOLUTION
• Unit will not start. • Cord not plugged in. • Plug tool into a working outlet.
• Circuit fuse is blown. • Replace circuit fuse. (If the
product repeatedly causes the
circuit fuse to blow, discontinue
use immediately and have it
serviced at a Porter Cable service
center or authorized servicer.)
• Circuit breaker is tripped. • Reset circuit breaker. (If the
product repeatedly causes the
circuit breaker to trip,
discontinue use immediately
and have it serviced at a Porter
Cable service center or
authorized servicer.)
• Cord or switch is damaged. • Have cord or switch replaced
at a Porter Cable Service
Center or Authorized Servicer
For assistance with your product, visit our website at www.portercable.com for a list of service
centers, or call the Porter-Cable Customer Care Center at (888) 848-5175.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to orderparts, visitourservice website at
www.portercable.com. You can alsoorder parts from your nearest Porter-Cable Factory Service
Center or Porter-Cable Authorized Warranty Service Center. Or, youcancall our Customer Care
Center at (888) 848-5175.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about
Porter-Cable, its factory service centers orauthorized warranty service centers,visit our website at
www.portercable.com orcall our Customer Care Center at(888) 848-5175.All repairs made by our
service centers are fully guaranteed against defective material and workmanship. We cannot
guarantee repairsmade or attempted by others.
You can alsowrite to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,
Tennessee 38305, (888) 848-5175 -Attention: Product Service. Be sure to include all of the
information shownon the nameplateof yourtool (model number, type, serial number, etc.).
ACCESSORIES
WARNING: Since accessories, other than those offered by Porter-Cable, have not
been tested with this product, use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only Porter-Cable recommended accessories should be
used with this product.
A complete line of accessories is available from your Porter-Cable Factory Service
Center or a Porter-Cable Authorized Warranty Service Center. Please visit our Web Site
www.portercable.com for a catalog or for the name of your nearest supplier.
10
THREE YEAR LIMITED WARRANTY
PORTER-CABLE will repair or replace, without charge, any defects due to faulty
materials or workmanship for three years from the date of purchase for tools (two years
for batteries). This warranty does not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty repair information, visit
www.portercable.com or call (888) 848-5175. This warranty does not apply to
accessories or damage caused where repairs have been made or attempted by others.
This warranty gives you specific legal rights and you may have other rights which vary in
certain states or provinces.
In addition to the warranty, PORTER-CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the
performance of your PORTER-CABLE Power Tool for any reason, you can return it within
90 days from the date of purchase with a receipt for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained in the
packaging, call the local company or see website for warranty information.
To register your tool for warranty service visit our website at www.portercable.com
.
WARNING LABEL REPLACEMENT
If your warning labels become illegible or are missing, call (888) 848-5175 for a free
replacement.
The following are PORTER-CABLE trademarksforoneor morepower tools and accessories: a gray
and black colorscheme; a “four point star”design; and three contrasting/outlined longitudinal stripes.
The following are also trademarks for one or more Porter-Cable and Deltaproducts: 2 BY 4®, 890™,
Air America®,AIRBOSS™,Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders Saw®,
ChargeAir®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's Saw®, Delta®,
DELTA®, DeltaIndustrial®, DELTA MACHINERY & DESIGN™, Delta ShopmasterandDesign®,
Delta X5®, Deltacraft®, DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND DESIGN®, EASY
AIR®, EASYAIR TO GO™, ENDURADIAMOND®, Ex-Cell®, FrontBevel Lock®,GetYours While
the Sun Shines®,Grip to Fit®, GRIPVAC™, GTF®,HICKORY WOODWORKING®,Homecraft®,
HPFRAMER HIGH PRESSURE®,IMPACT SERIES™, Innovation That Works®, Jet-Lock®,Job
Boss®, Kickstand®, LASERLOC®, LONG-LASTINGWORK LIFE®, MAX FORCE™, MAX LIFE®,
Micro-Set®, Midi-Lathe®, Monsoon®, MONSTER-CARBIDE™,Network®, OLDHAM®,Omnijig®,
PCEDGE®, Performance Crew™, Performance Gear®, Pocket Cutter®, Porta-Band®,PortaPlane®, Porter Cable®, Porter-Cable Professional Power Tools®, Powerback®, POZI-STOP™,
PressureWave®,PRO4000®, Proair®, Quicksand and Design®, Quickset II®, QUIET DRIVE
TECHNOLOGY™, QUIET DRIVE TECHNOLOGY AND DESIGN™, Quik-Change®, QUIK-TILT®,
RAPID-RELEASE™, RAZOR®, Redefining Performance®, Riptide®, Safe GuardII®, Sand Trap
and Design®,Sanding Center®, Saw Boss®, Shop Boss®, Sidekick®, Site Boss®, Speed-Bloc®,
Speedmatic®, Stair Ease®, SteelDriver Series®, SUPERDUTY®, T4 & DESIGN®, THE
AMERICANWOODSHOP®,THE PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®,
TIGERCLAW®,TIGERCLAW AND DESIGN®, Torq-Buster®, TRU-MATCH®,T-Square®,
Twinlaser®, Unifence®,Uniguard®, UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®,
Versa-Feeder®, VIPER®, VT™, VTRAZOR™, Water Driver®, WATER VROOM®, Waveform®,
Whisper Series®, X5®,YOUR ACHIEVEMENT. OUR TOOLS.®
Trademarks noted with ® are registered in the United States Patent and Trademark Officeandmay
also be registered in other countries. Other trademarks may apply.
4825 Highway45 North
Jackson,Tennessee 38305
(888) 848-5175
www.portercable.com
Loading...