Porter-Cable 90550095, PC1800HV User Manual

18 Volt Hand Vac

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

CATALOG NUMBER

PC1800HV

Aspirateur portatif 18 volts

Aspiradora manual de 18 v

Instruction manual

Manuel d'instructions Manual de'instrucciones

Batteries and chargers sold separately

90550095 PC1800HV 4/1/09 1:25 PM Page 1

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE USING THE UNIT.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

Some household dust contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm such as asbestos and lead in lead based paint.

To reduce the risk of fire, electrical shock or injury:

• DO NOT use outdoors or on wet surfaces.

• DO NOT leave vacuum with battery installed. Remove battery from tool when not in use

and before servicing.

• DO NOT allow vacuum to be used as a toy. Close attention is necessary when used by

or near children.

• USE ONLY as described in this manual. Use only manufacturer's recommended

attachments.

• DO NOT use with damaged cord or plug. If vacuum is not working as it should, has

been dropped, damaged, left outdoors, or dropped into water, return it to a service center.

• DO NOT pull or carry by cord, use cord as a handle, close a door on cord, or pull cord

around sharp edges or corners. Keep cord away from heated surfaces.

• DO NOT handle plug or vacuum with wet hands.

• KEEP hair, loose clothing, fingers, and all parts of body away from openings and

moving parts.

• TURN OFF all controls before removing battery.

• USE EXTRA CARE when cleaning on stairs.

• DO NOT use to pick up flammable or combustible liquids such as gasoline or use in

areas where they may be present.

• DO NOT pick up anything that is burning or smoking, such as cigarettes, matches or hot

ashes.

• STORE IDLE TOOLS. When not in use, the vacuum should be stored in a dry, high or

locked up place – out of reach of children.

• MAINTAIN TOOL WITH CARE. Keep fan area clean for best and safest performance.

Follow instructions for proper maintenance.

• DO NOT attempt to repair the vacuum. To assure product safety and reliability,

repairs, maintenance, and adjustments should be performed by authorized PORTER-CABLE service centers.

• DO NOT unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• DO NOT use without filter in place.

• DO NOT use in areas where explosive vapors may be present.

90550095 PC1800HV 4/1/09 1:25 PM Page 2

• DO NOT use to pick up explosive dust, or in areas where air contains explosive dust

such as coal, grain, or other combustible material.

• Static shocks are possible in dry areas or when the relative humidity of the air is low. This is only temporary and does not affect the use of the vacuum. To reduce the frequency of static shocks, add moisture to the air with a console or installed humidifier.

• DO NOT put any objects into openings. Do not use with any opening blocked; keep free of dust, lint, hair and everything that may reduce air flow.

• DO NOT ALLOW THE CORD TO HANG OVER THE EDGE OF A TABLE OR COUNTER OR TOUCH HOT SURFACES. The unit should be placed or mounted away from sinks and hot surfaces.

• DO NOT place outlet of vacuum near eyes or ears when operating.

• DISCONNECT BATTERY PACK FROM VACUUM BEFORE MAKING ANY ADJUSTMENTS, CHANGING ACCESSORIES, SERVICING, MOVING, OR STORING THE VACUUM. Such preventative safety measures reduce the risk of

starting the tool accidentally.

• AVOID ACCIDENTAL STARTING. Be sure the switch is in the OFF position before inserting the battery pack.

• USE RECOMMENDED ACCESSORIES. Consult the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.

• NEVER LEAVE VACUUM RUNNING UNATTENDED. TURN POWER OFF.

• KEEP YOUR WORK AREA CLEAN AND WELL LIT. Cluttered benches and dark areas invite accidents.

• AVOID BODY CONTACT WITH GROUNDED SURFACES SUCH AS PIPES, RADIATORS, RANGES AND REFRIGERATORS. There is an increased risk of electric shock if your body is grounded.

• DO NOT OVERREACH. KEEP PROPER FOOTING AND BALANCE AT ALL TIMES. Proper footing and balance enables better control of the vacuum in unexpected situations.

• USE SAFETY EQUIPMENT. ALWAYS WEAR EYE PROTECTION. Dust mask, non- skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

• DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON OR OFF. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

• SERVICE MUST BE PERFORMED ONLY BY QUALIFIED REPAIR PERSONNEL. Service or maintenance performed by unqualified personnel could result in a risk of injury.

• WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. FOLLOW INSTRUCTIONS IN THE MAINTENANCE SECTION OF THIS MANUAL. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

• This appliance is intended for household use only.

• The label on your tool may include the following symbols. The symbols and their definitions are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current

o ................no load speed

................Class I Construction ..................earthing terminal

....................(grounded) ..................safety alert symbol

................Class II Construction …/min ..........revolutions or reciprocation

....................(double insulated) ....................per minute

90550095 PC1800HV 4/1/09 1:25 PM Page 3

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery chargers.

• Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.

Shock hazard. Do not allow any liquid to get inside charger. Burn hazard. To reduce the risk of injury, charge only designated

PORTER-CABLE batteries. Other types of batteries may burst causing personal injury and damage.

Under certain conditions, with the charger plugged in to the power supply, the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

• When using an extension cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.

7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m

Wire Size AWG

18 18 16 16 14 14 12

FUNCTIONAL DESCRIPTION Figure A

1. On/off trigger

2. Bowl release button

3. Dust bowl

4. Battery port

5. Hose

6. Bowl to hose adaptor

7. Crevice tool

8. Universal adaptor

LI-ION Battery Packs and Chargers

Battery: LI-ION 18V

Charger: LI-ION

PC18BL

PC18BLX

PC18BLEX

PCLMVC

PCXMVC

Description Cat. #

NI-CD Battery Packs and Chargers

This product can accept any of the batteries and chargers listed in the chart below.

Battery: NI-CD 18V Charger: NI-CD

PC18B

PCMVC

PCXMVC

Description Cat. #

90550095 PC1800HV 4/1/09 1:25 PM Page 4

• DO NOT attempt to charge the battery pack with any chargers other than the ones

in this manual. The charger and battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than charging designated

PORTER-CABLE rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger. This will reduce risk of

damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock, or electrocution.

• An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the

cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size.

• Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not mount charger on wall or permanently affix charger to any surface. The charger is intended to use on a flat, stable surface (i.e., table top, bench top).

• Do not operate charger with damaged cord or plug — have them replaced immediately.

• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized service center.

• Do not disassemble charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard household electrical power (120

Volts). Do not attempt to use it on any other voltage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION FOR BATTERY PACKS

For safe operation, read this manual and manuals originally supplied with

tool before using the charger.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created

when LI-ION battery packs are burned.

• Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may

ignite the dust or fumes.

• If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed, the battery electrolyte for Li-ion batteries is composed of a mixture of liquid organic carbonates and lithium salts. For NI-CD batteries it is a 25-35% solution of potassium hydroxide.

• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention.

Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

• Charge the battery packs only in PORTER-CABLE chargers.

90550095 PC1800HV 4/1/09 1:25 PM Page 5

• DO NOT splash or immerse in water or other liquids. This may cause premature cell failure.

• Do not store or use the tool and battery pack in locations where the temperature

may reach or exceed 105°F (40C˚) (such as outside sheds or metal buildings in summer).

Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to service center for recycling.

BATTERY CAP INFORMATION

Battery storage and carrying caps are provided for use whenever the battery is out of the tool or charger. Remove cap before placing battery in charger or tool.

Fire hazard. Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR)

actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. NOTE: LI-ION batteries should not be put in checked baggage.

STORAGE RECOMMENDATIONS

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold.

2. Long storage will not harm the battery pack or charger. Under proper conditions LI-ION batteries, can be stored for 5 years or more.

CHARGING PROCEDURE

PORTER-CABLE chargers are designed to charge PORTER-CABLE battery packs in 30-60 minutes depending on the pack being charged.

1. Plug the charger into an appropriate outlet before inserting the battery pack.

2. Insert the battery pack into the charger. (Fig. B)

3. The LED will flash indicating that the battery is being charged.

4. The completion of charge is indicated by the LED remaining on continuously. The pack is fully charged and may be used at this time or left on the charger.

CHARGER DIAGNOSTICS

This charger is designed to detect certain problems that can arise with the battery packs or the power source. Problems are indicated by one LED flashing in different patterns.

Battery Cap

90550095 PC1800HV 4/1/09 1:25 PM Page 6

BAD BATTERY

The charger can detect a weak or damaged battery. The LED flashes in the pattern indicated on the label. If you see this bad battery blink pattern, do not continue to charge the battery. Return it to a service center or a collection site for recycling.

HOT/COLD PACK DELAY

When the charger detects a battery that is excessively hot or excessively cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery has normalized. After this happens, the charger automatically switches to the Pack Charging mode. This feature ensures maximum battery life. The light flashes in the pattern indicated on the label.

PROBLEM POWER LINE

When the charger is used with some portable power sources such as generators or sources that convert DC to AC, the charger may temporarily suspend operation. The LED flashes in the pattern indicated on the label. This indicates that the power source is out of limits.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left connected with the LED glowing indefinitely. The charger will keep the battery pack fresh and fully charged. This charger features an automatic tune-up mode which equals or balances the individual cells in the battery pack to allow it to function at peak capacity. Battery packs should be tuned up weekly or whenever the battery no longer delivers the same amount of work. To use the automatic tune-up mode, place the battery pack in the charger and leave it for at least 8 hours.

IMPORTANT CHARGING NOTES

1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F (+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. To facilitate the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly: a. Check current at receptacle by plugging in a lamp or other appliance b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. c. Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C). d. If charging problems persist, take the tool, battery pack and charger to your local service center.

4. The battery pack should be recharged when it fails to produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE to use under these conditions. Follow the charging procedure. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited to, steel wool,

aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

Shock hazard. Do not allow any liquid to get inside charger.Never attempt

to open the battery pack for any reason. If the plastic housing of the battery pack breaks or cracks, return to a service center for recycling.

INSTALLING AND REMOVING THE BATTERY PACK FROM THE TOOL

Make certain the lock-off button is engaged to prevent switch actuation

before removing or installing battery.

90550095 PC1800HV 4/1/09 1:25 PM Page 7

• TO INSTALL BATTERY PACK: Insert battery pack into tool as shown in figure C.

• TO REMOVE BATTERY PACK: Depress the battery

release button as shown in figure D and pull battery pack out of tool.

OPERATING INSTRUCTIONS

SWITCHING ON AND OFF

To start, depress the On/Off trigger once until it clicks. To stop, depress the On/Off trigger a second time until it clicks.

CLEANING & EMPTYING THE PRODUCT (FIGURES E-K)

Never use the hand vac without its filter. NOTE: The filter is re-usable. Do not confuse it

with a disposable dust bag, and do not throw it away when the product is emptied. (Use catalog number PCHVF150AR filter).

Removing the Bowl and Filter

• Remove the dust bowl by pressing the dust bowl release button and pulling the bowl down and out (figure E).

• Empty the debris from the bowl (figure F).

90550095 PC1800HV 4/1/09 1:25 PM Page 8

Cleaning the Filter

• Remove the filter from the dust bowl by pulling it straight out (figure G).

• To restore optimum airflow tap filter end cap against a hard surface to loosen debris

(figure H).

Important Filter Cleaning Notes:

• DO NOT BRUSH.

• DO NOT clean filter media with abrasive materials.

• DO NOT scrub to clean between pleats.

• DO NOT spray water or high pressure air from the inside to the outside of filter. This

will permanently damage the filter’s ability to stop

dust.

• To replace the filter, place it back into the bowl aligning the triangle on the filter with the triangle on the bowl as shown in figure I. Important: For best vacuum

results, make sure filter is fully seated in bowl and is properly aligned.

• To replace the bowl, place it back onto the handle and click firmly into position as shown in figure J.

Important: For best vacuum results, empty bowl after every use. Maximum dust collection will only

be obtained with a clean filter and an empty dust bowl. If dust begins to fall back out of the product after it is switched off, this indicates that the bowl is full and requires emptying.

• Never immerse the product in water. A damp cloth and soapy water should be used to clean the exterior (figure K). Always ensure the product is completely dry before re-use or storing.

Bowl

Filter

Triangles

90550095 PC1800HV 4/1/09 1:25 PM Page 9

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the LI-ION or NI-CD battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by PORTER-CABLE. RBRC™ in cooperation with PORTER-CABLE and other battery users, has established programs in the United States to facilitate the collection of spent LI-ION or NI-CD batteries. Help protect our environment and conserve natural resources by returning the spent LI-ION or NI-CD battery to an authorized PORTER-CABLE service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our Customer Care Center at (888) 848-5175.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our website at www.portercable.com or call our Customer Care Center at (888) 848-5175. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others. You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.).

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Battery pack not installed properly. • Check battery pack

installation.

• Battery pack not charged. • Check battery pack charging requirements.

• Battery pack will not charge. • Battery pack not inserted into charger. • Insert battery pack into charger until LED appears.

• Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details.

• Surrounding air temperature • Move charger and battery

too hot or too cold. pack to a surrounding air

temperature of above 40 degrees F (4,5°C) or below 105 degrees F (+40,5°C).

SPECIAL NOTES FOR USE WITH LITHIUM BATTERIES

• Unit shuts off abruptly. • Battery pack has reached its • Allow battery pack to cool maximum thermal limit. down.

• Out of charge. ( To • Place on charger and

maximize the life of the allow to charge. battery pack it is designed to shutoff abruptly when the charge is depleted.)

For assistance with your product, visit our website at www.portercable.com for a list of service centers, or call the PORTER-CABLE Customer Care Center at (888) 848-5175.

90550095 PC1800HV 4/1/09 1:25 PM Page 10

ACCESSORIES

Since accessories, other than those offered by PORTER-CABLE, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only PORTER-CABLE recommended accessories should be used with this product.

A complete line of accessories is available from your PORTER-CABLE Factory Service Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our Web Site www.portercable.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase for tools (two years for batteries). This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www

.portercable.com or call (888) 848-5175. This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, PORTER-CABLE tools are covered by our: 1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year after purchase. 90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performance of your PORTER-CABLE Power Tool for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warranty information.

To register your tool for warranty service visit our website at www

.portercable.com.

ARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (888) 848-5175 for a free replacement. The following are PORTER-CABLE trademarks for one or more power tools and accessories: a gray

and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal stripes. The following are also trademarks for one or more PORTER-CABLE and Delta products: 2 BY 4®, 890™, Air America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders Saw®, Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's Saw®, Delta®, DELTA®, Delta Industrial®, DELTA MACHINERY & DESIGN™, Delta Shopmaster and Design®, Delta X5®, Deltacraft®, DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND DESIGN®, EASY AIR®, EASY AIR TO GO™, ENDURADIAMOND®, Ex-Cell®, Front Bevel Lock®, Get Yours While the Sun Shines®, Grip to Fit®, GRIPVAC™, GTF®, HICKORY WOODWORKING®, Homecraft®, HP FRAMER HIGH PRESSURE®, IMPACT SERIES™, Innovation That Works®, Jet-Lock®, Job Boss®, Kickstand®, LASERLOC®, LONG-LASTING WORK LIFE®, MAX FORCE™, MAX LIFE®, Micro-Set®, Midi-Lathe®, Monsoon®, MONSTER-CARBIDE™, Network®, OLDHAM®, Omnijig®, PC EDGE®, Performance Crew™, Performance Gear®, Pocket Cutter®, Porta-Band®, PortaPlane®, PORTER-CABLE®, PORTER-CABLE Professional Power Tools®, Powerback®, POZISTOP™, Pressure Wave®, PRO 4000®, Proair®, Quicksand and Design®, Quickset II®, QUIET DRIVE TECHNOLOGY™, QUIET DRIVE TECHNOLOGYAND DESIGN™, Quik-Change®, QUIKTILT®, RAPID-RELEASE™, RAZOR®, Redefining Performance®, Riptide®, Safe Guard II®, Sand Trap and Design®, Sanding Center®, Saw Boss®, Shop Boss®, Sidekick®, Site Boss®, SpeedBloc®, Speedmatic®, Stair Ease®, Steel Driver Series®, SUPERDUTY®, T4 & DESIGN®, THE AMERICAN WOODSHOP®, THE PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®, TIGERCLAW®, TIGERCLAW AND DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®, UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR ACHIEVEMENT. OUR TOOLS.®

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Other trademarks may apply.

4825 Highway 45 North

Jackson, Tennessee 38305

(888) 848-5175

www.portercable.com

90550095 PC1800HV 4/1/09 1:25 PM Page 11

+ 25 hidden pages