Portech MV-372 User Manual

MV-372

VoIP GSM Gateway

User Manual

PORTech Communications Inc.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

【Content】

1.INTRODUCTION ................................................................................................................. 1

2.FUNCTION DESCRIPTION ...............................................................................................1

3.PARTS LIST .......................................................................................................................... 1

4.DIMENSION..........................................................................................................................2

5.CHART OF THE DEVICE .................................................................................................. 3

6.CABLING............................................................................................................................... 4

7.WEB PAGE SETTING ......................................................................................................... 5

8.SYSTEM INFORMATION. ................................................................................................. 6

9. ROUTE .................................................................................................................................. 6

10.MOBILE.............................................................................................................................12

11.NETWORK ........................................................................................................................ 19

12.SIP SETTING .................................................................................................................... 23

13. NAT TRANS ..................................................................................................................... 32

14.SYSTEM AUTH. ............................................................................................................... 33

15.SAVE CHANGE ................................................................................................................ 34

16.UPDATE.............................................................................................................................35

17.REBOOT ............................................................................................................................37

18. IP SETTING .....................................................................................................................38

19.SPECIFICATION ............................................................................................................. 40

20. APPENDIX: SETUP MV-370 WITH ASTERISK........................................................41

21.HOW TO SETUP ASTERISK TO RECEIVE CALLER ID FROM MV-372 ............47

22. SIMPLE STEPS................................................................................................................57

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-1-

1.Introduction

MV-372 is a 2 channels VoIP GSM Gateway for call termination (VoIP to
GSM ) and origination (GSM to VoIP). It is SIP based and compatible
with Asterisk. It can enable to make 2 calls simultaneously from IP
phones to GSM networks and GSM network to IP phone.

2.Function description

2.1 VoIP(SIP)、GSM(MV-372) conversion.

2.2 50 sets of LAN->MOBILE routes setting，50 sets of MOBILE->LAN

routes setting.

2.3 Voice response for setting and status (dial in from mobile).

2.4 Series connections to save bills.

2.5 Standard SIP(RFC2543,RFC3261) protocol，

Communicates with other gateway or PC.

3.Parts list

Please check the parts for any missing parts. If do, please contact

our agents：

3.1 「MV-372」main body

3.2 Power adaptor AC-DC (110V AC – 12V DC) or (220V AC – 12V DC)

3.3 Network cable

3.4 Antenna

3.5 User Manual

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-2-

4.Dimension

(1)

(2)

(4)

(3)

14.5cm

17cm

3.9

cm

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-3-

5.Chart of the device

5.1 Antenna：Antenna connector.

5.2 DC 12V：Power input.

5.3 LAN：LAN port. It also can be DHCP Server.

5.4 WAN: RJ-45 internet connector，standard RJ-45 socket，connect to

HUB.

5.5 PWR (Power LED)：Light up when power is normal.

5.6 VoIP1：an indicator light of VoIP1

5.7 VoIP2：an indicator light of VoIP2

5.8 LINK Indicator：Light up when network is connected.

5.1

5.2

5.3

5.4

5.5

5.6

5.7

5.8

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-4-

6.CABLING

6.1 Connect the internet cable from HUB to the ‘WAN’ connector of the

MV-372.

*If you need to stack up more MV-372,you can stack up as follows.

6.2 Connect the antenna and put it in proper position to get the best

signal reception.

6.3 Insert the SIM card from back of the main body. (take the slide off

first).

6.4

Click reset button 3 sec. MV-372 will restore default IP. Other

setting as usual.

6.5 Connect the power adaptor. The ‘POWER’ LED should be light up.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-5-

7.Web Page Setting

When the IP setting is done, the operator may setup all the rest

parameters via web page. Browse the IP address from Internet

Explorer (e.g. http://192.168.0.100

)。The following page shows up：

Enter the username and password for authentication. (default

username=voip, password=1234). The page follows when the

username and password are correct.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-6-

8.System Information.

8.1 When you login the web page, you can see the demo system current
system information like firmware version, company… etc in this
page.

8.2 Also you can see the function lists in the left side. You can use
mouse to click the function you want to set up.

9. Route

Important:

The route table -50 sets can share by two channels

The setting,please refer 10.2 Mobile setting

ex: Mobile 1 use the route table for item 0-24,

Mobile 2 use the route table for item 25-49

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-7-

9.1 Mobile TO LAN Settings

The operator may assign 50 sets of routing rule to transfer the call

incoming from MOBILE to LAN.

The MV-372 will transfer to the URL according to the caller ID of the
Mobile.

*CID：

(1) may enter the whole number, e.g. 0911111111

(2) only part of the number (prefix) e.g. 0911* means any number

starting with 0911 will be accepted

(3) * means all numbers can be accepted

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-8-

(4) N means the calls without the CID

Please note the priority of the rules. The item which has more digits will

have higher priority. If the digits are the same, then former one gets the

higher priority.

*URL：The IP address to transfer this call

(1) may enter the whole IP address, e.g. 192.168.0.101 or proxy

extension or phone number.

(2) If this field is blank or simply ‘N’, it means refuse to transfer.

(3) If an ‘*’ entered, it means 2-stages-dialing. The call will be

answered and prompt dial tone again to receive the IP address/sip

extension or any phone number as the destination. The caller may

enter the IP such as 192*168*0*101#.

*If the device have register proxy server/Asterisk ,you can enter any

destination phone number. Please note the proxy server/Asterisk

need to set the route of destination phone number.

Example:
(1) Mobile to Lan: 0932*,0911123456

MV-372 have register proxy server/Asterisk
The proxy server/Asterisk have the route “09”
When the caller’s prefix number is 0932,MV-372 will connect
0911123456 automaticlly

(2) Mobile to Lan: *,*

Any caller call the MV-372’s sim,MV-372 will prompt dial tone.Caller
can enter IP or sip extension or phone number.
*sip extension or phone number both need to register SIP Proxy

Server or Asterisk.

*Phone number, SIP Proxy Server or Asterisk need to set the route

of this phone number.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-9-

9.2 Mobile to LAN Speed Dial Settings

When you set Mobile to LAN Speed Dial Settings and Mobile to
LAN at the same time,MV-372 will give priority to Mobile to LAN Speed
Dial Settings.

*The call will be answered and prompt dial tone again. When the caller

may enter the “Num”, system will connect the “URL” as destination.

E.g Num:0 Name:test URL:192.168.0.107

When the caller hear dial tone and enter 0, system will connect

192.168.0.107

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-10-

9.3 LAN to Mobile Settings

The operator may assign 50 sets of routing rule to transfer the call

incoming from LAN to MOBILE.

The MV-372 will transfer to the mobile number according to the incoming

URL
*URL：The IP address of the incoming call.

may enter the whole IP address, e.g. 192.168.0.101 or proxy server’s

extension. If a simple ‘*’ is entered, means no restriction for the

incoming IP address.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-11-

*Call Num：

1.may enter the whole number, e.g. 0911111111

2.a simple *”means 2-stages-dialing. The call will be answered and

prompt dial tone again to receive the called number as the

destination, e.g. 0911111111 or 0911111111#

3.#['d'n]['a'ppp] for one-stage dialing

[...] is option

'd'n means to delete the beginning n codes,

'a'ppp means to add 'ppp' in front.

for example #d2a09 means one-stage dialing,

delete the first 2 codes from your destination number,

then add 09 in front as the new destination number.

Example:

Lan to Mobile: *, #
(1)MV-372 and Lan Phone both need to register proxy server or Asterisk.
(2)Proxy server/asterisk set the route that the prefix of destination number
(3)When you dial any destination phone number from lan phone,MV-372 will connect

this call auto.

Example of Application:

When you call the ch.1 MV-372 gsm number,it will provide dial tone and you enter a
destination number.
Then ch.2 MV-372 will dial this number and connect.
ch.1 MV-372: mobile to lan set route table *,*
ch.2 MV-372:lan to mobile set route table *,#
Additionally, two channels MV-372 both need to register proxy server or Asterisk.
And proxy server/asterisk set the route that the prefix of destination number dial out
from ch.2 MV-372.
*The channel 2 MV-372's ip: the first ip + :5062 (e.g http://192.168.0.100:5062)

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-12-

10.Mobile

10.1 Mobile Status

(1)Network Registration：The telecom carrier which the SIM card been

registered.

(2)SIM Card ID：SIM card ID.
(3)Signal Quality：Signal quality.

(4)GSM S/N : IMEI Number

(5)Incoming IP：The IP address of the last incoming call from LAN.

(6)Incoming IP Name: proxy server name
(7)Outgoing IP：The IP address of the last outgoing call to LAN.

(8)Incoming Mob：The caller ID of the last incoming call from MOBILE.
(9)Outgoing Mob：The called number of the last outgoing call to MOBILE.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-13-

10.2 Mobile Setting

(1) VoIP Tx Gain: To adjust the volume of LAN side.

(2) VoIP Rx Gain: To adjust the volume of Mobile side.

GSM

VoIP

Codec

LAN

(6)Rx

(5) Tx

DTMF

(1)VoIP Tx Gain

(2) VoIP Rx Gain

(1) (2)

(3)

(6) (7)

(8)

(9)

(10)

(11)

GSM

Codec

Rx

Tx

DTM

F

Mobile 1:

Mobile 2:

(4)

(12)

(5)

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-14-

(3)LAN Dialtone Gain: DTMF Reciver is not good,you can adjust gain

down.

(4) ON/Off: If you use this channel,please click on. Otherwise,please

click off.

(5)Routing Range:The route table -50 sets can share by two channels

ex: Mobile 1 use the route table for item 0-24,

Mobile 2 use the route table for item 25-49

(6)CODEC Tx Gain: as above

(7)CODEC Rx Gain: as above

(8) SIP From: Caller ID transfer

 Tel/User(Standard): If you need to register to Asterisk and proxy

server,please choose this option. And how to transfer the caller ID

to LAN,please refer 21.How to setup Asterisk to receive Caller ID

from MV-372 (page 42)

MV-372 will send the message as follows in the Packet.

From: " caller number " <sip:3001@192.168.0.228>;tag=51088abb

 Tel/Tel :

MV-372 will send the message as follows in the Packet.

From: "caller number" <sip: caller number @192.168.0.228>;tag=6ac93f7c

※Please note:If you choose this option,please don’t register to

Asterisk and proxy server. Please only fill proxy server ip and

choose Active: on (else field empty) in sip setting/service demain

 User/Tel

MV-372 will send the message as follows in the Packet.

From: " Username " <sip: caller number @192.168.0.228>;tag=7f130947

※ If you choose this option,please don’t register to Asterisk and

proxy server. Please only fill proxy server ip,Username and

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-15-

choose Active: on (else field empty) in sip setting/service

demain

(9)Presentation CLIR : If you need to block the Caller Id for call

termination,please choose Suppression

(10)Mobile PIN Code:If you need to unlock pin code via MV-372,you can

click “On” and enter pin code.

(11)LAN Answer Mode:

Answered : when mobile answer,then connect the call
Alerted : when the mobile is ringing back tone,then connect the call
Income : when lan dial out,then connect soon

(12)Answer Delay: Delay for incoming call when the ring.

(13)When you buy Quad band,you need to choose your GSM frequency

10.3 Mobile / Forward Setting :

When the first route are busying, SIP can transfer phone call to
another free route. When the device are busying, the phone call
can be transfer to another device (external equipments).

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-16-

*

"Forward Enable" is not motivate on Defualt value.

So please, mark "Forward Enable" this blank to motivate this function.
Take SJ Phone for example: Profiles -> Edit -> Advanced -> Accept
redirection replies (Turn on the "Forward Enable", therefore the SJ
Phone can designate a port which are free to use.)

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-17-

Name

URL:Port

Fwd to Mobile1:

192.168.0.100:5060

Fwd to Mobile2:

192.168.0.100:5062

Fwd to External:

The Explanation of Picture:

Fwd to Mobile1:192.168.0.100 : 5060, it means when 5062 Port are
busying, SJ Phone can transfer the call to 5060 Port (192.168.0.100).

Fwd to Mobile2:192.168.0.100 : 5062, it means when 5060 Port are
busying, SJ Phone can transfer the call to 5062 Port (192.168.0.100).

 If both 5060 port and 5062 port are busying at same time, you can set

up "Fwd to External", then you can transfer the phone call to another
designate device.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-18-

10.4 Mobile / SMS Agent :

(1) Rx List: Read received SMS
(2) Dest Num: the Receiver’s phone number
(3) Message: Please fill the message that want to send to receiver.

When you click Rx List, you can view all received SMS as follows.

Click the serial no,you can view message as follows.

Read received SMS

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-19-

11.Network

In Network you can check the Network status, configure the WLAN
Settings , LAN Setting and SNTP settings.

11.1 Network Status: You can check the current Network setting in this

page.

11.2 WAN Settings: You can check the current Network setting in this

page.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-20-

(1) The TCP/IP Configuration item is to setup the WAN port’s network

environment. You may refer to your current network environment to
configure the system properly.

(2) The PPPoE Configuration item is to setup the PPPoE Username and

Password. If you have the PPPoE account from your Service
Provider, please input the Username and the Password correctly.

(3) The Bridge Item is to setuo the system Bridge mode Enable/Disable.

If you set the Bridge On, then the two Fast Ethernet ports will be
transparent.

(4) When you finished the setting, please click the Submit button.

11.3 LAN Settings: You can check the current Network setting in this

page.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-21-

(1) The TCP/IP Configuration item is to setup the WAN port’s network

environment. You may refer to your current network environment to
configure the system properly.

(2)DHCP Server: You may refer to your current network environment to

configure the system properly

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-22-

11.4 SNTP Settings:

SNTP Setting function: you can setup the primary and second SNTP
Server IP Address, to get the date/time information. Also you can base
on your location to set the Time Zone, and how long need to synchronize
again. When you finished the setting, please click the Submit button.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-23-

12.SIP Setting

In SIP Setting you can setup the Service Domain,Port Settings,Codec
Settings,RTP setting,RPort Setting and Other SettingS. If the VoIP
service is provided by ISP,you need to setup the related informations
correctly then you can register to SIP Proxy Server correctly.

12.1 In Servcie Domain Function you need to input the account and the

related informations in this page,please refer to your ISP Provider.
You can register three SIP accounts . You can dial the VoIP phone
to your friends via first enable SIP account and receive the phone
from the tree SIP account.

First you need to click Active to enable the Service Domain,then you can
input the following items.
(1)No.,: choose Mobile 1 or Mobile 2
(2) Display name: you can input the name you want to display.
(3) User name: you need to input the User Name get from your ISP.
(4) Register Name: you need to input the Register Name get from your

ISP.

(5) Register Password: you need to input the Register Password get

from ISP.

(6) Domain Server:you need to input the Domain Server get from your

ISP.
(7) Proxy Server:you need to input the Proxy Server get from your ISP.
(8) Outbound Proxy: you need to input the Outbound Proxy get from your

ISP. If your ISP does not provide the information,then you can skip

this item.
(9) You can see the Register Status in the Status item.
(10) When you finished the setting,please click the Submit button.

Remember to click “Save Charge”

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-24-

Example:
Register VoipBuster

Your Voipbuster username

Your Voipbuster password

Proxy Server’s IP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-25-

12.2 Port Setting
You can setup the SIP and RTP port number in this page. Each ISP
provider will have different SIP/RTPport setting, please refer to the ISP
to setup the port number correctly. When you finished the setting, please
click the Submit button.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-26-

12.3 Codec Settings:
You can setup the Codec priority, RTP packet length in this page. You
need to follow the ISP suggestion to setup these items. When you
finished the setting, please click the Submit button.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-27-

12.4 Codec ID Setting
You can setup the Codec ID in this page.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-28-

12.5 DTMF Setting
You can setup the DTMF Setting in this page.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-29-

12.6 RPort Function:
You can setup the RPort Enable/Disable in this page. To change this
setting, please following your ISP information. When you finished the
setting, please click the Submit button.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-30-

12.7 SIP Responses

12.7.1 486(busy here), 503(Service unavailable): When Device are

busying, you can select 486 or 505 to response to SIP.

12.7.2 180 Ring on/off: LAN TO MOBILE two stage dialing can be turn

off, therefore there will be no the Ring Back Tone, all the phone call will

be transferred to Voice-Mail directly. (For this function, 183 must be turn

on)

12.7.3 183(Session Progress)-->[It means"on progressing"] : When you

turn 183 on, it means you can hear voicemail while GMS side are

busying. We recommend you to turn this on if you use SIP Proxy.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-31-

12.8 Other Settings
Other Settings: you can setup the Hold by RFC and QoS in this page. To
change these settings. please following your ISP information. When you
finished the setting, please click the Submit button. The QoS setting is to
set the voice packets’ priority. If you set the value higher than 0, then the
voice packets will get the higher priority to the Internet. But the QoS
function still need to cooperate with the others Internet devices.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-32-

13. NAT Trans

In NAT Trans. you can setup STUN and uPnP function. These functions
can help your VoIP device working properly behind NAT.

13.1 STUN Setting: you can setup the STUN Enable/Disable and STUN

Server IP address in this page. This function can help your VoIP
device working properly behind NAT. To change these settings
please following your ISP information. When you finished the
setting, please click the Submit button.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-33-

14.System Auth.

In System Authority you can change your login name and password.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-34-

15.Save Change

In Save Change you can save the changes you have done. If you want to
use new setting in the VoIP system, You have to click the Save button.
After you click the Save button, the system will automatically restart and
the new setting will effect.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-35-

16.Update

In Update you can update the system’s firmware to the new one or do the
factory reset to let the system back to default setting.

16.1 Update firmware
(1) In New Firmware function you can update new firmware via HTTP in

this page. You can upgrade the firmware by the following steps:
(2)Select the firmware code type, Risc code.
(3)Click the “Browse” button in the right side of the File Location or you

can type the correct path and the filename in File Location blank.
(4)Select the correct file you want to download to the system then click

the Update button.

(5) Please click update/default setting after update firmware

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-36-

16.2 Restore Default Settings
In this page: Update/ Default Settings, you could restore the factory
default settings to the system.

All setting will restore default setting.

IP will retain original IP as usual not default IP.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-37-

17.Reboot

Reboot function you can restart the system. If you want to restart the
system, you can just click the Reboor button, then the system will
automatically.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-38-

18. IP Setting

The operator can setup or query the network parameters by dialing in the

mobile number which it SIM card has been put in the main body. The

status or result is response by voice. In the first 20 seconds after

power-on, the VoIP GSM Gateway enters the IP setting mode. The

operator may dial in the mobile number during this period to set or query

the network parameters.

Item

IVR Action IVR Menu Choice

Notes

1 Reboot #195#

After you hear “Option
Successful,” hang-

up. Unit will

reboot automatically.

2 Factory Reset #198#

System will automatically
Reboot.WARNING: ALL
User-Changeable”
NONDEFAULT SETTINGS
WILL BE LOST! This will
include network and service
provider data.

3 Check IP Address #120#

IVR will announce the current
IP

address , Default :

192.168.0.100

4 Check IP Type #121#

IVR will announce if DHCP in
enabled or disabled.

default : OFF

5 Check Network

Mask

#123#

IVR will announce the current

network mask.Default :

255.255.255.0

6

Check Gateway

IP
Address

#124#

IVR will announce the current
gateway IP address,

Default : 192.168.0.254

7 Check Primary #125#

IVR will announce the current

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-39-

DNS Server

setting in the Primary DNS
field.

Default : 192.168.0.1

8 Check Firmware

Version

#128#

IVR will announce the version
of the firmware running

9

Set as DHCP

client

#111#

The system will change to
DHCP
Client type

10 Set Static IP

Address

#112xxx*xxx*xxx
*xxx#

DHCP will be disabled and
system will change to the
Static IP type.
Enter IP address using

numbers on the telephone key

pad. Use the * (star) key when

entering a decimal point.

11 Set Network Mask #113xxx*xxx*xxx

*xxx#

Must set Static IP first.

Enter value using numbers on

th

e telephone key pad. Use

the * (star) key when entering

a decimal point.

12 Set Gateway IP

Address

#114xxx*xxx*xxx
*xxx#

Must set Static IP first.

Enter IP address using

numbers on the telephone key

pad. Use the * (star) key

when entering a decimal

point.

13 Set Primary DNS

Server

#115xxx*xxx*xxx
*xxx#

Must set Static IP first.

Enter IP address using

numbers on the telephone key

pad. Use the * (star) key

when entering a decimal

point.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-40-

19.Specification

19.1 Protocols

SIP (RFC2543,RFC3261)

19.2 TCP/IP

IP/TCP/UDP/RTP/RTCP/

CMP/ARP/RARP/SNTP

DHCP/DNS Client

IEEE802.1P/Q

ToS/DiffServ

NAT Traversal

STUN

uPnP

IP Assignment

Static IP

DHCP

PPPoE

19.3 Codec

G.711 u-Law

G.711 a-Law

G.723.1 (5.3k)

G.723.1 (6.3k)

G.729A

G.729A/B

19.4 Voice Quality

VAD

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-41-

CNG

AEC, LEC

Packet loss

19.5 GSM (MV-372)

Dual BAND: 900/1800 MHZ

Tri BAND(BenQ M23): 900/1800/1900 MHZ

Tri BAND(Siemens MC56): 850/1800/1900 MHZ

Quad BAND: 900/1800/1900/850 MHZ

20. Appendix: Setup MV-372 with Asterisk

20.1 Usage

A typical usage of such a gateway is to be able to give a call with your

normal mobile to any destination at voip cost :

Your mobile <----gsm network----> MV-372 <--lan--> Asterisk

<--internet--> VOIP provider <--whatever--> landline

To do such a call, you just call your MV-372 number (it has its own

simcard), then you get an invitation tone, then you dial the number which

is handled by Asterisk.

If you have some special deals with your mobile operator, like free

special number, you can call your MV-372 for free.

You can then call all around the world from your mobile at voip cost :-)

20.2 MV-372 Configuration

Once you've configured everything in the box, one good advice is to

unplug the power and to restart it. By this way you should have all the

parameters taken into account.

To have the MV-372 to work with Asterisk, you need first to configure the

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-42-

box.

Here are some screen shots showing all the important parameters.

You have to note that in all the configuration process, the MV-372 is

considered as extension '103' of the IPBX.

In Bold are the parameters depending on your installation

Here the '#' is important to avoid the two stage dialing when you give a

call from Asterisk to GSM.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-43-

The mobile number you give in that page are the authorised mobile

which can call GSM to Asterisk.

These mobile number must be defined as your GSM provider displays

the number.

If you don't know how it is displayed, just give a call to the box and check

the number given in the 'Incoming Mob' field of the 'Mobile Status' page.

Any number which is not in that list won't have acces to the LAN side, so

to Asterisk.

If you want to allow any number, just set '*' in that field ... but beware of

the bill ;-)

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-44-

Once Asterisk configuration is made, you should get 'Registered' on the

Realm1.

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-45-

It is very important to use only u-law or a-law as all DTMF is inband.

So if you want to be able to do some DISA when you call from GSM to

Asterisk, it has to be one of these 2 codecs.

These settings seem to be ok, just adjust ...

20.3 Antenna position

Another important thing is to properly place the provided antenna.

If your gsm reception is good, you should get around 18 or 19 as Signal

Quality in the "Mobile Status" page.

With that level of signal quality, your audio quality will be very good.

On the other end,the signal quality down to 11, audio becomes very jerky.

So, maximum signal quality = maximum audio quality.

20.4 Asterisk configuration

Once the MV-372 is set, you have to configure Asterisk.

On that side, you have to setup files as follow :

20.5 sip.conf

; GSM VOIP Gateway MV-372

[103]

type=friend

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-46-

username=103

fromuser=103

regexten=103 ; When they register, create extension 401

secret=xxxxxxx ; Asterisk extension password

context=gateway ; Incoming calls context

dtmfmode=inband ; Very important for DISA to work

call-limit=1 ; Limit to 1 call max

callerid=GSM Gateway <103>

host=dynamic

nat=no ; Gateway is not behind a NAT router

canreinvite=no ; Typically set to NO if behind NAT

insecure=very

qualify=yes

disallow=all

allow=ulaw ; prefered codec for DTMF detection

allow=alaw

20.6 extensions.conf

; ******* GSM Gateway incoming calls **********
[gateway]
exten => _103,1,Answer()
exten => _103,2,DigitTimeout(3) ; give enough time to do second stage
dialing
exten => _103,3,ResponseTimeout(5)
exten => _103,4,DISA(no-password|outgoing) ; here 'outgoing' is the
normal context to deal with the dial plan

[outgoing]
...
; example of LAN to GSM call
; call the MV-372 sim card mail box thru GSM
exten => _888,1,SetCallerID("xxxxxxxxxx")
exten => _888,2,Dial(SIP/${EXTEN}@103,60,r)
exten => _888,3,Hangup()

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-47-

21.How to setup Asterisk to receive Caller ID from MV-372

Test version

trixbox-2.2

SIP Softphone

 SJPhone 1.60.289a
 X-Lite 1105x

Modify file

 Add the following setting to/etc/asterisk/sip.conf

[1000]
type=friend
secret=1000
qualify=yes
nat=yes
host=dynamic
canreinvite=no
context=internal

[1001]
type=friend
secret=1001
qualify=yes
nat=yes
host=dynamic
canreinvite=no
context=internal

[1002]
type=friend
secret=1002
qualify=yes

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-48-

nat=yes
host=dynamic
canreinvite=no
context=internal

 Add the following setting to /etc/asterisk/extensions.conf

[internal]
exten => 1000,1,Dial(SIP/1000)
exten => 1001,1,Dial(SIP/1001)
exten => 1002,1,Dial(SIP/1002)

configure:
trixbox-2.2: address=192.168.66.202:5060
SJPhone: address=192.168.66.145:5060; username=1000,
displayname=user_1000
X-Lite: address=192.168.66.145:7331; username=1001, displayname=user_1001
MV-372: address=192.168.66.203:5060; username=1002, displayname=user_1002

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-49-

test1

pstn  call 0928492911(mobile number)  MV-372  hear the second dial tone,call

SoftPhone’s number  SoftPhone  show pstn caller id

This Is X-Lite receiving packet, red word is pstn number. Test ok.

INVITE sip:1001@192.168.66.145:7331 SIP/2.0
Via: SIP/2.0/UDP 192.168.66.202:5060;branch=z9hG4bK3d0bbaf7;rport
From: "035678238" <sip:1002@192.168.66.202>;tag=as580472a7
To: <sip:1001@192.168.66.145:7331>
Contact: <sip:1002@192.168.66.202>
Call-ID: 20fa417265e6a26d0b0aae4f551f06f3@192.168.66.202
CSeq: 102 INVITE
User-Agent: Asterisk PBX
Max-Forwards: 70
Date: Tue, 22 May 2007 02:50:37 GMT
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Content-Type: application/sdp
Content-Length: 242

v=0
o=root 2737 2737 IN IP4 192.168.66.202
s=session
c=IN IP4 192.168.66.202
t=0 0
m=audio 15852 RTP/AVP 0 8 101
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
a=silenceSupp:off - - - -

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-50-

SIP/2.0 200 Ok
Via: SIP/2.0/UDP 192.168.66.202:5060;branch=z9hG4bK3d0bbaf7;rport
From: "035678238" <sip:1002@192.168.66.202>;tag=as580472a7
To: <sip:1001@192.168.66.145:7331>;tag=677373503
Contact: <sip:1001@192.168.66.145:7331>
Call-ID: 20fa417265e6a26d0b0aae4f551f06f3@192.168.66.202
CSeq: 102 INVITE
Content-Type: application/sdp
Server: X-Lite release 1105x
Content-Length: 254

v=0
o=1001 4804366 4807851 IN IP4 192.168.66.145
s=X-Lite
c=IN IP4 192.168.66.145
t=0 0
m=audio 8000 RTP/AVP 0 8 3 101
a=rtpmap:0 pcmu/8000
a=rtpmap:8 pcma/8000
a=rtpmap:3 gsm/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv

test 2

SoftPhone  call 1002  MV-372  hear second dial tone and call pstn  pstn
answer  show caller id-mobile number 0928492911

This Is X-Lite receiving packet. Test ok.

INVITE sip:1002@192.168.66.202 SIP/2.0

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-51-

Via: SIP/2.0/UDP

192.168.66.145:7331;rport;branch=z9hG4bK4C4315351FC84CA582D14FB8C25F
C3BF
From: user_1001 <sip:1001@192.168.66.202:7331>;tag=1121869743
To: <sip:1002@192.168.66.202>
Contact: <sip:1001@192.168.66.145:7331>
Call-ID: F4B32CA6-1835-4E68-941A-C685B39C43FF@192.168.66.145
CSeq: 63148 INVITE
Proxy-Authorization: Digest
username="1001",realm="asterisk",nonce="0d3b2879",response="8aaaaa5b5ad53
654bf0a2ab0fa9bb118",uri="sip:1002@192.168.66.202",algorithm=MD5
Max-Forwards: 70
Content-Type: application/sdp
User-Agent: X-Lite release 1105x
Content-Length: 254

v=0
o=1001 5111461 5111501 IN IP4 192.168.66.145
s=X-Lite
c=IN IP4 192.168.66.145
t=0 0
m=audio 8000 RTP/AVP 0 8 3 101
a=rtpmap:0 pcmu/8000
a=rtpmap:8 pcma/8000
a=rtpmap:3 gsm/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-15
a=sendrecv

SIP/2.0 200 OK
Via: SIP/2.0/UDP

192.168.66.145:7331;branch=z9hG4bK4C4315351FC84CA582D14FB8C25FC3BF
;received=192.168.66.145;rport=7331

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-52-

From: user_1001 <sip:1001@192.168.66.202:7331>;tag=1121869743
To: <sip:1002@192.168.66.202>;tag=as2a2fbf98
Call-ID: F4B32CA6-1835-4E68-941A-C685B39C43FF@192.168.66.145
CSeq: 63148 INVITE
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Contact: <sip:1002@192.168.66.202>
Content-Type: application/sdp
Content-Length: 242

v=0
o=root 2737 2737 IN IP4 192.168.66.202
s=session
c=IN IP4 192.168.66.202
t=0 0
m=audio 13798 RTP/AVP 0 8 101
a=rtpmap:0 PCMU/8000
a=rtpmap:8 PCMA/8000
a=rtpmap:101 telephone-event/8000
a=fmtp:101 0-16
a=silenceSupp:off - - - -

register issue

The packet date from Asterisk as follows.
Please note, user_1002’s display name don’t appear
So the website’s Display Name is not available

<-- SIP read from 192.168.66.203:5060:
REGISTER sip:192.168.66.202 SIP/2.0
Via: SIP/2.0/UDP

192.168.66.203:5060;rport;branch=z9hG4bK590e92b551233a10a0ae71944c19b5
aa
From: <sip:1002@192.168.66.202>;tag=4e36d8f1

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-53-

To: <sip:1002@192.168.66.202>
Call-ID: 7e45b773130f1fc945efcee502f84042@192.168.66.203
Contact: <sip:1002@192.168.66.203:5060>
CSeq: 10 REGISTER
Expires: 300
Authorization: Digest
username="1002",realm="asterisk",nonce="3ca93a1e",response="4d39ccb0dae64
bb2f1341e9896ac1ea7",uri="sip:192.168.66.202",algorithm=MD5
User-Agent: CMI CM5K
Content-Length: 0

--- (11 headers 0 lines) --­Using latest REGISTER request as basis request
Sending to 192.168.66.203 : 5060 (NAT)
Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP

192.168.66.203:5060;branch=z9hG4bK590e92b551233a10a0ae71944c19b5aa;rec
eived=192.168.66.203;rport=5060
From: <sip:1002@192.168.66.202>;tag=4e36d8f1
To: <sip:1002@192.168.66.202>
Call-ID: 7e45b773130f1fc945efcee502f84042@192.168.66.203
CSeq: 10 REGISTER
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Contact: <sip:1002@192.168.66.202>
Content-Length: 0

--­Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 401 Unauthorized

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-54-

Via: SIP/2.0/UDP

192.168.66.203:5060;branch=z9hG4bK590e92b551233a10a0ae71944c19b5aa;rec
eived=192.168.66.203;rport=5060
From: <sip:1002@192.168.66.202>;tag=4e36d8f1
To: <sip:1002@192.168.66.202>;tag=as13a32ae8
Call-ID: 7e45b773130f1fc945efcee502f84042@192.168.66.203
CSeq: 10 REGISTER
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
WWW-Authenticate: Digest algorithm=MD5, realm="asterisk", nonce="5def9231"
Content-Length: 0

--­Scheduling destruction of call
'7e45b773130f1fc945efcee502f84042@192.168.66.203' in 15000 ms
asterisk1*CLI>
<-- SIP read from 192.168.66.203:5060:
REGISTER sip:192.168.66.202 SIP/2.0
Via: SIP/2.0/UDP

192.168.66.203:5060;rport;branch=z9hG4bK672fa67f59c2223275f5ee286d27597a
From: <sip:1002@192.168.66.202>;tag=4e36d8f1
To: <sip:1002@192.168.66.202>
Call-ID: 7e45b773130f1fc945efcee502f84042@192.168.66.203
Contact: <sip:1002@192.168.66.203:5060>
CSeq: 11 REGISTER
Expires: 300
Authorization: Digest
username="1002",realm="asterisk",nonce="5def9231",response="046a412f4e7ed4
e98fd507416994a80a",uri="sip:192.168.66.202",algorithm=MD5
User-Agent: CMI CM5K
Content-Length: 0

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-55-

--- (11 headers 0 lines) --­Using latest REGISTER request as basis request
Sending to 192.168.66.203 : 5060 (NAT)
Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 100 Trying
Via: SIP/2.0/UDP

192.168.66.203:5060;branch=z9hG4bK672fa67f59c2223275f5ee286d27597a;recei
ved=192.168.66.203;rport=5060
From: <sip:1002@192.168.66.202>;tag=4e36d8f1
To: <sip:1002@192.168.66.202>
Call-ID: 7e45b773130f1fc945efcee502f84042@192.168.66.203
CSeq: 11 REGISTER
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Contact: <sip:1002@192.168.66.202>
Content-Length: 0
12 headers, 0 lines
Reliably Transmitting (NAT) to 192.168.66.203:5060:
OPTIONS sip:1002@192.168.66.203:5060 SIP/2.0
Via: SIP/2.0/UDP 192.168.66.202:5060;branch=z9hG4bK7b92dd8a;rport
From: "Unknown" <sip:Unknown@192.168.66.202>;tag=as5dee3942
To: <sip:1002@192.168.66.203:5060>
Contact: <sip:Unknown@192.168.66.202>
Call-ID: 5ebc2211278e2cb7699911ad39454d4e@192.168.66.202
CSeq: 102 OPTIONS
User-Agent: Asterisk PBX
Max-Forwards: 70
Date: Tue, 22 May 2007 03:11:54 GMT
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Content-Length: 0

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-56-

--­Transmitting (NAT) to 192.168.66.203:5060:
SIP/2.0 200 OK
Via: SIP/2.0/UDP

192.168.66.203:5060;branch=z9hG4bK672fa67f59c2223275f5ee286d27597a;recei
ved=192.168.66.203;rport=5060
From: <sip:1002@192.168.66.202>;tag=4e36d8f1
To: <sip:1002@192.168.66.202>;tag=as13a32ae8
Call-ID: 7e45b773130f1fc945efcee502f84042@192.168.66.203
CSeq: 11 REGISTER
User-Agent: Asterisk PBX
Allow: INVITE, ACK, CANCEL, OPTIONS, BYE, REFER, SUBSCRIBE, NOTIFY
Expires: 300
Contact: <sip:1002@192.168.66.203:5060>;expires=300
Date: Tue, 22 May 2007 03:11:54 GMT
Content-Length: 0

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-57-

22. Simple Steps

Step 1. Change the Network setting if you need (Network/network setting)
Step 2. Register SIP proxy Server or Asterisk or VoipBuster if you need

(sip setting/service domain)

Step 3. Set Route ( request )

mobile to lan:

(1) *,* --->it is two stage dialing.

when mobile call in,MV-372 will provide dial tone

and you can enter

ip or asterisk extension or phone number.

*

If you want to enter phone number,please note your asterisk need

to have route of destination number.

(2) *, specific extension or IP or phone number

when mobile call in,MV-372 will connect with this specific extension
or IP or phone number auto

*

If you want to set specific phone number,please note your asterisk

need to have route of destination number.

Lan to Mobile:

(1)

*,* --->it is two stage dialing.

when lan phone call in,MV-372 will provide dial tone and you can
enter mobile number.

(2) *, specific mobile number

when lan phone call in,MV-372 will connect with the specific mobile
number auto.

(3) *,#--->It is 1 stage dialing

When lan phone and MV-372 both register Asterisk,
you can dial any destination number from lan phone directly.

*

Please note:Asterisk need to set route of destination number that
dial out from MV-372

* All changes both need to click "save and change"

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

-58-

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]