MV-370 / MV-372
VoIP GSM Gateway
User Manual
MV-370
MV-372
PORTech Communications Inc.
【Content】
1. Introduction........................................................................................................... 1
2. Function description............................................................................................ 1
3. Parts list ................................................................................................................ 1
4. Dimension: 14.5cm x 17cm x 3.9cm.................................................................... 2
5. MV-370 Panel description.................................................................................... 3
6. MV-372 Panel description.................................................................................... 4
7. CABLING............................................................................................................... 5
8. Web Page Setting ................................................................................................. 6
9. System Information.............................................................................................. 7
10. Route ................................................................................................................... 7
10.1 Mobile TO LAN Settings.................................................................................. 8
10.2 Call Back Service (50 sets)........................................................................... 10
10.3 Mobile to LAN Speed Dial Settings............................................................... 11
10.4 LAN to Mobile Settings.................................................................................. 12
11. Mobile................................................................................................................ 14
11.1 Mobile Status ................................................................................................ 14
11.2 Mobile Setting ............................................................................................... 15
11.3 Mobile / Forward Setting:.............................................................................. 18
11.4 Mobile / SMS Agent: ..................................................................................... 20
11.5 Send Bulk of SMS via Microsoft Excel.......................................................... 22
11.6 use AT Command via Telnet or your program .............................................. 32
11.7 USSD SIM Balance Check via Telnet.......................................................... 33
11.8 SIM Setting ................................................................................................... 35
11.9 Operator Setting............................................................................................ 37
11.10 Cell Info....................................................................................................... 39
11.11 USSD (Unstructured Supplementary Service Data).................................... 44
12. Network ............................................................................................................. 48
13. SIP Setting......................................................................................................... 52
13.7.1 486(busy here), 503(Service unavailable):................................................. 60
13.7.2 180 Ring on/off:.......................................................................................... 60
13.7.3 183(Session Progress)............................................................................... 60
13.7.4 Dial Peer.................................................................................................... 60
13.7.5 Call data to server...................................................................................... 60
14. NAT Trans ......................................................................................................... 65
15. Update ............................................................................................................... 66
16. System Auth...................................................................................................... 68
17. Save Change..................................................................................................... 69
18. Reboot............................................................................................................... 70
19. IP Setting........................................................................................................... 71
20. Specification ..................................................................................................... 73
20.1 Protocols....................................................................................................... 73
20.2 TCP/IP .......................................................................................................... 73
20.3 Codec............................................................................................................ 73
20.4 Voice Quality................................................................................................. 73
20.5 GSM (MV-370/MV-372) ................................................................................ 74
21. Simple Steps..................................................................................................... 75
22. Appendix: Setup MV-370/MV-372 with Asterisk............................................. 76
-1-
1. Introduction
MV-370/MV-372 is a 1/2 channels VoIP GSM Gateway for call
termination (VoIP to GSM) and origination (GSM to VoIP). It is SIP based
and compatible with Asterisk. It can enable to make 1/2 calls
simultaneously from IP phones toGSM networks andGSM network to IP
phone.
2. Function description
2.1 VoIP(SIP)、GSM(MV-370/MV-372) conversion.
2.2 50 sets of LAN->MOBILE routes setting，50 sets of MOBILE->LAN
routes setting.
2.3 Voice response for setting and status (dial in from mobile).
2.4 Series connections to save bills.
2.5 Standard SIP(RFC2543,RFC3261) protocol，
Communicates with other gateway or PC.
3. Parts list
Please check the parts for any missing parts. If do, please contact
our agents：
3.1 「MV-370/MV-372」main body
3.2 Power adaptor AC-DC (110V AC – 12V DC) or (220V AC– 12V DC)
3.3 Network cable
3.4 Antenna
3.5 User Manual
-2-
4. Dimension: 14.5cm x 17cm x 3.9cm
(3.1) MV-370
(2)
(4)
(3)
14.5cm
17cm
3.9cm
(3.1) MV-372
-3-
5. MV-370 Panel description
5.1 Antenna：Antenna connector.
5.2 DC 12V：Power socket.
5.3 LAN: Standard RJ-45 socket, connecting to Hub circuit.
5.4 PWR: Power indicator light, red light. Light is on when system’s
power supply is normal.
5.5 MOBILE: GSM indicator light, green light. Light flashes when
GSM status is normal; light turns on constantly when GSM is
called.
5.6 LAN: LAN indicator light, green light. Light flashes when Lan is
called; light turns off when GSM answered.
5.7 LINK: Link indicator light, green light. Light is on when network
is connected correctly.
(5.1) (5.2) (5.3) (5.4) (5.6)
(5.5) (5.7)
17cm
14.5cm
3.9cm
-4-
6. MV-372 Panel description
6.1 Antenna：Antenna connector.
6.2 DC 12V：Power input.
6.3 LAN：LAN port. It also can be DHCP Server.
6.4 WAN: RJ-45 internet connector，standard RJ-45 socket，connect to
HUB.
6.5 PWR (Power LED)：Light up when power is normal.
6.6 VoIP1：an indicator light of VoIP1
6.7 VoIP2：an indicator light of VoIP2
6.8 LINK Indicator：Light up when network is connected.
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
-5-
7. CABLING
7.1 Connect the internet cable from HUB to the ‘WAN’ connector of the
MV-372.
*If you need to stack up more MV-372, you can stack up as follows.
7.2 Connect the antenna and put it in proper position to get the best
signal reception.
7.3 Insert the SIM card from back of the main body. (Take the slide off
first).
7.4 MV-370/MV-372 support manual switch IP MODE to DHCP and
manual restore to original firmware for update failure.
There are SW1 and SW2 button shows as follow diagram:
7.4.1 SW1 function: Restore the factory default IP 192.168.0.100
STEP: Please press the SW1 in 7~8 seconds till the Mobile and LAN led flash blink.
7.4.2 SW2 function: Switch MV-37X IP to DHCP MODE
-6-
STEP: Please press the SW2 about 7~8 seconds till the Mobile and LAN led flash
blink.
7.4.3 SW1 + SW2 function: Manual restore and restart MV to original firmware for
update failure.
STEP: Please remove the MV power cable, and press the SW1 and SW2 at
meantime. Then plug in the power DC 12V and don’t let go in 4~5 seconds. When
Mobile and LAN led flash blink, you can reboot the device and login to 192.168.0.100
for firmware update procedure.
7.5 Connect the power adaptor. The ‘POWER’ LED should be light up.
8. Web Page Setting
When the IP setting is done, the operator may setup all the rest
parameters via web page. Browse the IP address from Internet
Explorer (e.g. http://192.168.0.100). The following page shows up：
Enter the username and password for authentication. (default
username=voip, password=1234). The page follows when the
username and password are correct.
-7-
9. System Information.
9.1 When you login the web page, you can see the demo system current
system information like firmware version, company… etc in this
page.
9.2 Also you can see the function lists in the left side. You can use
mouse to click the function you want to set up.
10. Route
Important:
The route table -50 sets can share by two channels
The setting,please refer 11.2 Mobile setting
ex: Mobile 1 use the route table for item 0-24,
Mobile 2 use the route table for item 25-49
-8-
10.1 Mobile TO LAN Settings
The operator may assign 50 sets of routing rule to transfer the call
incoming from MOBILE to LAN.
The MV-370/MV-372 will transfer to the URL according to the caller ID of
the Mobile.
*CID：
(1) may enter the whole number, e.g. 0911111111
(2) only part of the number (prefix) e.g. 0911* means any number
starting with 0911 will be accepted
-9-
(3) * means all numbers can be accepted
(4) N means the calls without the CID
Please note the priority of the rules. The item which has more digits will
have higher priority. If the digits are the same, then former one gets the
higher priority.
*URL：The IP address to transfer this call
(1)may enter the whole IP address, e.g. 192.168.0.101 or proxy
extension or phone number.
(2)If this field is blank or simply ‘N’, it means refuse to transfer.
(3)If an ‘*’ entered, it means 2-stages-dialing. The call will be
answered and prompt dial tone again to receive the IP address/sip
extension or any phone number as the destination. The caller may
enter the IP such as 192*168*0*101#.
*If the device have register proxy server/Asterisk ,you can enter any
destination phone number. Please note the proxy server/Asterisk
need to set the route of destination phone number.
Example:
(1) Mobile to Lan: 0932*,0911123456
MV-370/MV-372 have register proxy server/Asterisk
The proxy server/Asterisk have the route “09”
When the caller’s prefix number is 0932,MV-370/MV-372 will
connect 0911123456 automatically
(2) Mobile to Lan: *,*
Any caller call the MV-370/MV-372’s sim,MV-370/MV-372 will prompt dial tone.
Caller can enter IP or sip extension or phone number.
*sip extension or phone number both need to register SIP Proxy
Server or Asterisk.
*Phone number, SIP Proxy Server or Asterisk need to set the route
of this phone number.
-10-
10.2 Call Back Service (50 sets)
You can set call back service as the following steps
(1) CID : set the phone number here (up to 50 sets)
(2) URL: # (# is the command of call back)
Application:
a.Call MV-370/ MV-372
b.MV-370/ MV-372 willdetect the phone number is in call back list or not
c.If yes, MV-370/ MV-372 will reject the call, and call it back
d.You will receive the call from MV-370/ MV-372, and prompt a dial tone
-11-
10.3 Mobile to LAN Speed Dial Settings
When you set Mobile to LAN Speed Dial Settings and Mobile to
LAN at the same time, MV-370/MV-372 will give priority to Mobile to LAN
Speed Dial Settings.
*The call will be answered and prompt dial tone again. When the caller
may enter the “Num”, system will connect the “URL” as destination.
E.g Num: 0 Name: test URL:192.168.0.107
When the caller hear dial tone and enter 0, system will connect
192.168.0.107
-12-
10.4 LAN to Mobile Settings
The operator may assign 50 sets of routing rule to transfer the call
incoming from LAN to MOBILE.
The MV-370/MV-372 will transfer to the mobile number according to the
incoming URL
*URL：The IP address of the incoming call.
may enter the whole IP address, e.g. 192.168.0.101 or proxy server’s extension. If
a simple ‘*’ is entered, means no restriction for the incoming IP address.
*Call Num：
-13-
1. May enter the whole number, e.g. 0911111111
2. A simple *”means 2-stages-dialing. The call will be answered and prompt dial
tone again to receive the called number as the destination, e.g. 0911111111 or
0911111111#
3. # for one-stage dialing
4. # ['d'n]['a'ppp] for one-stage-dialing
[...] is option
'd'n means to delete the beginning n codes,
'a'ppp means to add 'ppp' in front.
For example #d123a456 means one-stage dialing,
delete the first 123 from your destination number,
then add 456 in front as the new destination number.
Example:
Lan to Mobile: *, #
(1)MV-370/MV-372 and Lan Phone both need to register proxy server or Asterisk.
(2)Proxy server/asterisk set the route that the prefix of destination number
(3)When you dial any destination phone number from lan phone,MV-370/MV-372 will
connect this call auto.
Example of Application:
When you call the ch.1 MV-370/MV-372 GSM number, it will provide dial tone and
you enter a destination number.
Then ch.2 MV-370/MV-372 will dial this number and connect.
ch.1 MV-370/MV-372: mobile to lan set route table *,*
ch.2 MV-370/MV-372:lan to mobile set route table *,#
Additionally, two channels MV-370/MV-372 both need to register proxy server or
Asterisk.And proxy server/asterisk set the route that the prefix of destination
number dial out from ch.2 MV-370/MV-372.
*The channel 2 MV-370/MV-372’s IP: the first IP :5062(e.g.
http://192.168.0.100:5062)
-14-
11. Mobile
11.1 Mobile Status
(1)Network Registration： The SIM card of telecom carrier is been
registered
(2)SIM Card ID：SIM card ID.
(3)Signal Quality：Signal quality. (4)GSM S/N : IMEI Number
(5)Motion State: The status of SIM card
(6)Incoming IP：The IP address of the last incoming call from LAN.
(7)Incoming IP Name: proxy server name
(8)Outgoing IP：The IP address of the last outgoing call to LAN.
(9)Incoming Mob：The caller ID of the last incoming call from MOBILE.
(10)Outgoing Mob: The called number of the last outgoing call to
MOBILE.
-15-
11.2 Mobile Setting
(1) VoIP Tx Gain: To adjust the volume of LAN side.
(2) VoIP Rx Gain: To adjust the volume of Mobile side.
GSM
VoIP
Codec
LAN
(6)Rx
(5) Tx
DTMF
(1)VoIP Tx Gain
(2) VoIP Rx Gain
GSM
Codec
Rx
Tx
DTMF
Mobile 1:
Mobile 2:
(1)
(3)
(2)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(13)
Only change “mobile” into “on” or
“off”, just click “submit”, no need
to click “save change”
(12)
(14)
(15)
(16)
-16-
(3)LAN Dial tone Gain: DTMF Receiver is not good, you can adjust gain
down.
(4)Routing Range: The route table -50 sets can share by two channels
ex: Mobile 1 use the route table for item 0-24,
Mobile 2 use the route table for item 25-49
(5)CODEC Tx Gain: as above
(6)CODEC Rx Gain: as above
(7) SIP From: Caller ID transfer
Tel/User (Standard): If you need to register to Asterisk and proxy
server, please choose this option. And how to transfer the caller ID
to LAN, please refer 21.How to setup Asterisk to receive Caller ID
from MV-370/MV-372 (page 42)
MV-370/MV-372 will send the message as follows in the Packet.
From: “caller number” <sip:3001@192.168.0.228>;tag=51088abb
User/User (Standard): If you need to register to Asterisk and proxy
server, please choose this option.
MV-370/MV-372 will send the message as follows in the Packet.
From: " 3001" <sip:3001@192.168.0.228>;tag=51088abb
Tel/Tel :
MV-370/MV-372 will send the message as follows in the Packet.
From: "caller number" <sip: caller number @192.168.0.228>;tag=6ac93f7c
※Please note: If you choose this option, please don’t register to
Asterisk and proxy server. Please only fill proxy server IP and
choose Active: on (else field empty) in sip setting/service domain
User/Tel
MV-370/MV-372 will send the message as follows in the Packet.
From: “Username” <sip: caller number @192.168.0.228>;tag=7f130947
-17-
※ If you choose this option, please don’t register to Asterisk and
proxy server. Please only fill proxy server ip,Username and
choose Active: on (else field empty) in sip setting/service
domain
(8)Answer Delay: Delay for incoming call when the ring.
(9)Presentation CLID: If you need to block the Caller Id for call
termination, please choose Suppression
(10) Restart Dial Fail: In this feature, user can initialize and register the
module while GSM module dials fail in couple times. When GSM
module is dysfunctional, it can avoid the device shut down in
advance.
(11)Mobile PIN Code: If you need to unlock pin code via
MV-370/MV-372, you can click “On” and enter pin code.
(12) Dial Prefix: The prefix number of outgoing calls. When Lan to Mobile,
MV-370/MV-372 will automatically add the “Dial prefix” for outgoing
mobile.
(13)LAN Answer Mode:
*Answered: when mobile answer, and then connect the call
*Alerted: when the mobile is ringing back tone, then connect the
call
*Income: when Lan dial out, then connect soon
(14) Init AT Cmd: User can fill the AT Command for GSM module
(15) Band Type: You can manual setting according to your GSM
Frequency of carrier.
(16) ON/Off: If you use this channel, please click on. Otherwise, please
click off.
-18-
11.3 Mobile / Forward Setting:
When the first route are busying, SIP can transfer phone call to
another free route. When the device are busying, the phone call
can be transfer to another device (external equipments).
*"Forward Enable" is not motivate on Default value.
So please, mark "Forward Enable" this blank to motivate this function.
Take SJ Phone for example: Profiles -> Edit -> Advanced -> Accept
redirection replies (Turn on the "Forward Enable", therefore the SJ
Phone can designate a port which are free to use.)
-19-
Name
URL:Port
Fwd to Mobile1:
192.168.0.100:5060
Fwd to Mobile2:
192.168.0.100:5062
Fwd to External:
The Explanation of Picture:
Fwd to Mobile1:192.168.0.100 : 5060, it means when 5062 Port are
busying, SJ Phone can transfer the call to 5060 Port (192.168.0.100).
Fwd to Mobile2:192.168.0.100 : 5062, it means when 5060 Port are
busying, SJ Phone can transfer the call to 5062 Port (192.168.0.100).
If both 5060 port and 5062 port are busying at same time, you can set
up "Fwd to External", then you can transfer the phone call to another
designate device.
-20-
11.4 Mobile / SMS Agent:
(1) Rx List: Read received SMS
(2) Dest Num: the Receiver’s phone number
(3) Message: Please fill the messages that want to send to receiver.
When you click Rx List, you can view all received SMS as follows.
Click the serial no,you can view message as follows.
Read received SMS
2 mode:
ASC7(ASCII 7 bit)
UCS2(Unicode 16
-21-
-22-
11.5 Send Bulk of SMS via Microsoft Excel
First of all, please open a new Excel file.
Step 1 Format Cells
Here, we need you to format cells to “Text” first.
Please click mouse right key, and choose “Format Cells”
BLANk A
-23-
BLANk B
Step 2
In the Format Cells, please select “Text”
Please do this action for BLANk A and B both.
-24-
Step 3
BLANK A: is for you to key “phone numbers”
BLANK B: is for you to key “text”
Step 4 Save the file
-25-
Save the type as “Unicode Text”
-26-
Step 5
Open MVsms_exe - MV-SMS (Configuration Settings)
Step 6
Please do the configuration as following:
MV-378
-27-
MV-374
MV-372 & MV-370
=2
=1
-28-
Step 7
Run MV-SMS program
Step 8
1. Open File
-29-
2. Open the “Excel file” that you just saved
-30-
Step 9
Sending
-31-
Step 10
Send SMS Complete
-32-
11.6 use AT Command via Telnet or your program
Allows your program or Telnet Send/receive SMS with AT Command
Port: 23
Please enter account
and password
Choose module
Enter “ate1”,then you can see
your at command below
Enter at+cmgs=”phone number”
Enter short message and ctrl+Z
-33-
11.7 USSD SIM Balance Check via Telnet
1. USSD Request: It’s the USSD code for your operator to check balance AR.
2. Module command:
Please enter “15” for Siemens BG2W module
Please enter “0” for Simcom module
You can check this information on main page in Module Description
1. USSD Request
2. Module command
-34-
After you send the USSD request, MV will receive the SMS from operator
Please check the incoming SMS on SMS Agent
-35-
11.8 SIM Setting
1. CU ID: It’s the ID for MV and SIM Server Transfer Protocol, within
1~9999. Each MV under same SIM Sever should setup different CU
ID, and no reusing parameter. E.g. If you put “888” on 1stMV-378 that
you can’t use “888” on 2ndMV-378, and so on.
2. Mode
a. Local: Disable Remote SIM feature
b. Bank: Enable Remote SIM Bank feature, and manage SIM card on
SBK-32 SIM Bank.
c. Server: Enable Remote SIM Server feature, and allocate SIM
cards on SBK-32 SIM Bank.
3. Mobile
a. ID: Put in 8 digits (hexadecimal, also base 16), which used for
GSM Module ID identification to Remote SIM protocol. User can
define the ID. IF it’s Server Mode, just leave it default. If it’s Bank
Mode, No reusing GSM Module ID for same SIM Bank.
-36-
b. Group: Fill in SIM Group number for Remote GSM module. Server
follow SIM Group Number to allocate SIM card to correspond GSM
module
4. Card ID: Put in 8 digits (hexadecimal, also base 16), which used for
SIM Card ID identification to Remote SIM protocol. User can define
the ID. If it’s in Server Mode, Card ID can be blank or default. As for
Bank Mode, Card ID must be corresponding to SIM Card ID of SIM
Bank.
5. Bank URL: If it’s Bank Mode, please fill SIM Bank IP and Port Number.
On other hand, please leave blank for Server Mode.
6. Server URL: If it’s Server Mode, please fill SIM Server IP and Port
Number. On other hand, please leave blank for Bank Mode.
7. Status: User can check the SIM Card ID of GSM module and IP, Port
Number of SIM bank.
-37-
11.9 Operator Setting
1. Operator ID: When GSM module is registered, user can click the List
to show all available operators in that area. You will see like follows
diagram.
-38-
2. Work Mode:
a.Every time reset module:
Fill the assigned Operator ID, then press Submit bottom and save
change. After reboot, GSM module will research the operator ID and
registered the base station.
b.Manual:
Fill the assigned Operator ID, then press Now bottom. GSM module
will search that Operator ID and registered after reboot.
-39-
11.10 Cell Info
It shows BTS (BCCH) cells of the cellular network and register to new
BCCH selection. Support Quad band-BG2W, Quad band-M10 and
firmware V10.185 above only.
Please work with this feature when the mobile status is “Stand by/Active”.
It detects the surrounding active cell, up to 7 cells and shows Cell ID,
signal and best signal (RXlev). The No.0 shows the data of current
registered cell. Follow by No.1 to No.6 cell is based on cell signal (best to
low).
MCC : Mobile Country Code
LAC : Location Area Code
Cell : Cell Identifier
BSIC: Base Station Identity Code
BCCH: Broadcast Control Channel
RxLev: Received Signal level in dbm
-40-
How to Configure
1. You can choose a BCCH channel by clicking on the cell. The module will
automatically register in the new BCCH.
E.g. If you would like to register BCCH channel on No.4 cell, please click no4 select
like below.
-41-
2. System will show the cell number information once you select on Preferred this
Cell form. Please click the submit button and Save Change on left to restart the
module.
-42-
After system restart and turn to Standby, please check on No.0 cell and confirm the
current registered cell you selected. At the point, the GSM module won’t provide the
data of surrounding cell signal, but shows -110dbm on No.1 to No.6 RxLev, which
means GSM signal 0.
-43-
3. If you would like to research all the surrounding BCCH cells again, please cancel
Preferred this Cell selection first and send Submit, Save Change to restart the
gateway. That, System can detect the surrounding active cell, up to 6 cells and
display Cell ID, signal and best signal (RXlev).
-44-
11.11 USSD (Unstructured Supplementary Service Data)
You can check USSD screen for SIM balance remaining and SIM recharge (add
value) automatically. Please work with this feature when the mobile status is “Stand
by/Active”. And ensure your Service provider has given you a USSD
string(Command) for checking SIM Balance and Recharge the SIM Card.
1. Balance (SIM balance remaining)
Step1: Enter Balance checking USSD command in column
Step 2: Click Send button
When selected, system will check the balance of SIM and display the reply of receive
message as below
-45-
2. Recharge (add value)
Step1: Enter the Recharging USSD command in column
Step 2: Click Send button
When selected, system will display the reply of receive message as below
3. Checking (If above ways are failed, please select this)
Step 1: Enter the complete AT command in Cm3 column
Ex. AT+CUSD=1,*145*11#,15
Step 2: Click Send button
When selected, system will display the reply of receive message as below
-46-
4. Rx Decoder
a. None: GSM Format (Default)
b. ASC7: ASCII 7bit
c.UCS2: Unicode 16bit
When user select default GSM Format(None), it may not receive correct GSM code
due to the different operator or GSM module/chipset. Please check below example,
-47-
In this case, user need to select other RX Decoder (ASCII or UCS2) to receive
correct message.
For Example,
None format: When user send command, “*145*11#”, the return message show on
system, “C1F1B80CA797C9”
ASC7 Format: In this format, the return message is “Accepted”
-48-
12. Network
In Network you can check the Network status, configure the WLAN
Settings, LAN Setting and SNTP settings.
12.1 Network Status: You can check the current Network setting in this
page.
-49-
12.2 WAN Settings
(1) The TCP/IP Configuration item is to setup the WAN port’s network
environment. You may refer to your current network environment to
configure the system properly.
(2) The PPPoE Configuration item is to setup the PPPoE Username and
Password. If you have the PPPoE account from your Service
Provider, please input the Username and the Password correctly.
(3) The Bridge Item is to setup the system Bridge mode Enable/Disable.
If you set the Bridge On, then the two Fast Ethernet ports will be
transparent.
(4) When you finished the setting, please click the Submit button.
-50-
12.3 LAN Settings
(1) The TCP/IP Configuration item is to setup the WAN port’s network
environment. You may refer to your current network environment to
configure the system properly.
(2)DHCP Server: You may refer to your current network environment to
configure the system properly
-51-
12.4 SNTP Settings:
SNTP Setting function: you can setup the primary and second SNTP
Server IP Address, to get the date/time information. Also you can base
on your location to set the Time Zone, and how long need to synchronize
again. When you finished the setting, please click the Submit button.
-52-
13. SIP Setting
In SIP Setting you can setup the Service Domain, Port Settings, Codec
Settings,RTP setting,RPort Setting and Other Settings. If the VoIP
service is provided by ISP,you need to setup the related informations
correctly then you can register to SIP Proxy Server correctly.
13.1 In Service Domain Function you need to input the account and the
related informations in this page, please refer to your ISP Provider.
You can register three SIP accounts. You can dial the VoIP phone
to your friends via first enable SIP account and receive the phone
from the tree SIP account.
First you need to click Active to enable the ServiceDomain, thenyou can
input the following items.
(1)No.,: choose Mobile 1 or Mobile 2
(2) Display name: you can input the name you want to display.
(3) User name: you need to input the User Name get from your ISP.
(4) Register Name: you need to input the Register Name get from your
ISP.
-53-
(5) Register Password: you need to input the Register Password get
from ISP.
(6) Domain Server:you need to input the Domain Server get from your
ISP.
(7) Proxy Server:you need to input the Proxy Server get from your ISP.
(8) Outbound Proxy: you needto input the Outbound Proxy get from your
ISP. If your ISP does not provide the information,then you can skip
this item.
(9) You can see the Register Status in the Status item.
(10) When you finished the setting,please click the Submit button.
Remember to click “Save Charge”
Example:
Register VoipBuster
Your Voipbuster username
Your Voipbuster password
Proxy Server’s IP or domain name
-54-
13.2 Port Setting
You can setup the SIP and RTP port number in this page. Each ISP
provider will have different SIP/RTPport setting, please refer to the ISP
to setup the port number correctly. Whenyou finished the setting, please
click the Submit button.
-55-
13.3 Codec Settings:
You can setup the Codec priority, RTP packet length in this page. You
need to follow the ISP suggestion to setup these items. When you
finished the setting, please click the Submit button.
-56-
13.4 Codec ID Setting
You can setup the Codec ID in this page.
-57-
13.5 DTMF Setting
1. Format:
a. 2833: Default RFC2833, the type of DTMF Data Transfer Format
b. Inband: The Type of Inband DMTF Data Transfer Format
c. SIP Info: The Type of SIP-Info DMTF Data Transfer Format;
2. Duration: Default is -1. It’s the duration for MV-374/MV-378 to defect
sender’s DTMF. If the parameter is 0, MV-374/MV-378 won’t detect
sender’s DTMF. Parameter is 0~999 seconds. After that duration,
MV-374/MV-378 won’t detect DTMF.
3. Debounce: Default is 80ms.User can adjust for own. If DTMF is
adding more digits, please increase parameter over 80. If DMTF is
lost digit, please decrease parameter less than 80.
-58-
13.6 RPort Function:
You can setup the RPort Enable/Disable in this page. To change this
setting, please follow your ISP information. When you finished the
setting, please click the Submit button.
-59-
13.7 SIP Responses
Dial Peer Configuration Table corresponding IP
(please read next page)
*** If you have dial peer server, Sip
server/Asterisk set GSM route,please set Dial
Peer server’s IP**
-60-
13.7.1 486(busy here), 503(Service unavailable):
When Device is busy, you can select 486 or 505 to response to SIP.
13.7.2 180 Ring on/off:
LAN TO MOBILE two stage dialing can be turn off, therefore there will be
no the Ring Back Tone, all the phone call will be transferred to prompt
voice directly. (For this function, 183 must be turn on)
13.7.3 183(Session Progress)
[It means "on progressing"]: When you turn 183 on, it means you can
hear the prompt voice while GSM side is busy We recommend you to
turn this on if you use SIP Proxy.
13.7.4 Dial Peer
LAN to mobile: Dial peer software will look for available channel to dial out. E.g When
the first port is busy, MV-378 will use the second port to dail out…and so forth.
13.7.5 Call data to server
MV can provide Call Detail Record (CDR) for traffic and accounting management.
User need to download external Dial Peer software on PC and can monitor traffic.
Data ID: MV will create one default Data ID
Data Server: Please fill the PC’s IP, which is executed External Dial Peer Software
-61-
Edit DialPeer.ini
[Window]
Xpos=512
Ypos=252
Width=471
Height=399
[Info]
Total=16
[VoipIP]
1=192.168.0.100
2=192.168.0.100
3=192.168.0.100
4=192.168.0.100
5=192.168.0.100
6=192.168.0.100
7=192.168.0.100
8=192.168.0.100
9=192.168.0.110
10=192.168.0.110
11=192.168.0.110
12=192.168.0.110
13=192.168.0.110
14=192.168.0.110
15=192.168.0.110
16=192.168.0.110
[SipPort]
1=5060
2=5062
3=5064
4=5066
5=5068
6=5070
7=5072
8=5074
9=5060
10=5062
11=5064
12=5066
13=5068
14=5070
15=5072
16=5074
[RtpPort]
1=60000
2=60002
3=60004
4=60006
5=60008
6=60010
7=60012
8=60014
9=60000
10=60002
11=60004
12=60006
13=60008
14=60010
15=60012
16=60014
[PtcPort]
1=40000
2=40000
3=40008
4=40008
5=40016
6=40016
7=40024
8=40024
9=40000
10=40000
11=40008
12=40008
13=40016
14=40016
15=40024
16=40024
Total ip / port
The first
MV-378
The second
MV-378
The first
MV-378
The second
MV-378
The second
MV-378
The first
MV-378
The second
MV-378
The first
MV-378
The second
MV-378
-62-
Log
-63-
Status
The first MV-378
doesn’t register dial
peer software
The 1,4-8ch of
Second MV-378
turn off
The 2,3ch of
Second MV-378
idle
-64-
13.8 Other Settings
Other Settings: you can setup the Hold by RFC and QoS in this page. To
change these settings. please following your ISP information. When you
finished the setting, please click the Submit button. The QoS setting is to
set the voice packets’ priority. If you set the value higher than 0, then the
voice packets will get the higher priority to the Internet. But the QoS
function still need to cooperate with the others Internet devices.
-65-
14. NAT Trans
In NAT Trans. you can setup STUN and uPnP function. These functions
can help your VoIP device working properly behind NAT.
14.1 STUN Setting: you can setup the STUN Enable/Disable and STUN
Server IP address in this page. This function can help your VoIP
device working properly behind NAT. To change these settings
please following your ISP information. When you finished the
setting, please click the Submit button.
-66-
15. Update
In Update you can update the system’s firmware to the new one or
execute the factory reset to let the system back to default setting.
15.1 Update firmware
(1) Select the firmware code type, Risc code only.
(3)Click the “Browse” button in the right side of the File Location or you
can type the correct path and the filename in File Location blank.
(4)Select the correct file you want to download to the system then click
the Update button.
(5) Please click update/default setting after update firmware
NOTE: Please open the webpage from Internet Explorer, not compatible with FF or
Google Chrome
-67-
15.2 Restore Default Settings
In this page: Update/ Default Settings, you could restore the factory
default settings to the system. All setting will restore default setting.
IP will retain original IP as usual not default IP.
-68-
16. System Auth.
In System Authority you can change your login name and password.
-69-
17. Save Change
In Save Change you can save the changes you have done. If you want to
use new setting in the VoIP system, you have to click the Save button.
After you click the Save button, the system will automatically restart and
the new setting will effect.
-70-
18. Reboot
Reboot function you can restart the system. If you want to restart the
system, you can just click the Reboot button, then the system will
automatically.
-71-
19. IP Setting
The operator can setup or query thenetwork parameters by dialing in the
mobile number which it SIM card has been put in the main body. The
status or result is response by voice. In the first 20 seconds after
power-on, the VoIP GSM Gateway enters the IP setting mode. The
operator may dial in the mobile number during this period to set or query
the network parameters.
Item
IVR Action
IVR Menu Choice
Notes
1
Reboot
#195#
After you hear “Option
Successful,” hang-up. Unit will
reboot automatically.
2
Factory Reset
#198#
All setting (include IP) both
restore to default setting.
WARNING: ALL
User-Changeable”
NONDEFAULT SETTINGS
WILL BE LOST! This will
include network and service
provider data.
3
Check IP Address
#120#
IVR will announce the current
IP
address , Default :
192.168.0.100
4
Check IP Type
#121#
IVR will announce if DHCP in
enabled or disabled.
default : OFF
5
Check Network
Mask
#123#
IVR will announce the current
network mask.Default :
255.255.255.0
6
Check Gateway
IP
Address
#124#
IVR will announce the current
gateway IP address,
Default : 192.168.0.254
-72-
7
Check Primary
DNS Server
#125#
IVR will announce the current
setting in the Primary DNS
field.
Default : 192.168.0.1
8
Check Firmware
Version
#128#
IVR will announce the version
of the firmware running
9
Set as DHCP
client
#111#
The system will change to
DHCP
Client type
10
Set Static IP
Address
#112xxx*xxx*xxx
*xxx#
DHCP will be disabled and
system will change to the
Static IP type.
Enter IP address using
numbers on the telephone key
pad. Use the * (star) key when
entering a decimal point.
11
Set Network Mask
#113xxx*xxx*xxx
*xxx#
Must set Static IP first.
Enter value using numbers on
the telephone key pad. Use
the * (star) key when entering
a decimal point.
12
Set Gateway IP
Address
#114xxx*xxx*xxx
*xxx#
Must set Static IP first.
Enter IP address using
numbers on the telephone key
pad. Use the * (star) key
when entering a decimal
point.
13
Set Primary DNS
Server
#115xxx*xxx*xxx
*xxx#
Must set Static IP first.
Enter IP address using
numbers on the telephone key
pad. Use the * (star) key
when entering a decimal
point.
-73-
20. Specification
20.1 Protocols
SIP (RFC2543,RFC3261)
20.2 TCP/IP
IP/TCP/UDP/RTP/RTCP/
CMP/ARP/RARP/SNTP
DHCP/DNS Client
IEEE802.1P/Q
ToS/DiffServ
NAT Traversal
STUN
uPnP
IP Assignment
Static IP
DHCP
PPPoE
20.3 Codec
G.711 u-Law
G.711 a-Law
G.723.1 (5.3k)
G.723.1 (6.3k)
G.729A
G.729A/B
20.4 Voice Quality
VAD
-74-
CNG
AEC, LEC
Packet loss
20.5 GSM (MV-370/MV-372)
Quad Band:900/1800/1900/850MHZ
3G/UMTS: for all world and Japan (SoftBank Mobile,Docomo)
3G:EDGE/GPRS 850, 900, 1800, 1900 MHz / HSDPA/UMTS 850, 1900,
2100 MHz
CDMA 2000(800MHZ/1900MHZ)
**Please note**
Most CDMA operators don't offer Polarity reversing . So VoIP to
Mobile, MV-370 will connect soon. CDMA operators will start billing
soon. It doesn't wait mobile side answer.
CDMA Version doesn't support SMS Feature and 180/183
unavailable
-75-
21. Simple Steps
Step 1. Change the Network setting as you need (Network/network setting)
Step 2. Register SIP proxy Server or Asterisk or VoipBuster as you need
(sip setting/service domain)
Step 3. Set Mobile setting –adjust your gain as you need
Step 4. Set Route ( request )
mobile to LAN:
(1)
*,* --->it is two stage dialing.
when mobile call in,MV-370/MV-372 will provide dial tone and you can
enter ip or asterisk extension or phone number.
*
If you want to enter phone number,please note your asterisk need to
have route of destination number.
(2)
*, specific extension or IP or phone number
when mobile call in,MV-370/MV-372 will connect with this specific
extension or IP or phone number auto
*
If you want to set specific phone number,please note your asterisk
need to have route of destination number.
LAN to Mobile:
(1)
*,* --->it is two stage dialing.
when LAN phone call in,MV-370/MV-372 will provide dial tone and
you can enter mobile number.
(2)
*, specific mobile number
when LAN phone call in,MV-370/MV-372 will connect with the specific
mobile number auto.
(3)
*,#--->It is 1 stage dialing
When LAN phone and MV-370/MV-372 both register Asterisk,
you can dial any destination number from LAN phone directly.
*
Please note:Asterisk need to set route of destination number that
dial out from MV-370/MV-372
* All changes both need to click "save and change"
-76-
22. Appendix: Setup MV-370/MV-372 with Asterisk
M V -370/372 Settings
Can register Asterisk or not
Asterisk want to transfer
CLID,please choose Tel/Tel
(Not Reg)
-77-
Set your Asterisk IP,extension or *
As Asterisk GSM
Route
-78-
Port Settings:
Mobile1 > Sip port: 5060
Mobile2 > Sip port: 5062 Important!!!
Don't forget to Save changes and then reboot
-79-
Asterisk / Trixbox setting
Add SIP Trunk:
MV-372 must create 2 trunk.
First trunk: MV-372 ip:5060
Second Trunk:MV-372 ip:5062
Type your mobile
number
-80-
Type a trunk
name
Type MV-37X’s ip and port
The channel 2 is 5062 port
-81-
Set GSM Route that dial out via MV-37X
Frequency: Quad Band:900/1800/1900/850MHZ
GSM Module use Simcom sim340
Compliant to GSM phase 2/2+
-Class 4 (2W@850/900 MHz)
-Class 1 (1W@1800/1900 MHz)
The prefix of route :
09XXXXXXXX
After change , please press “Sumbit
changes” and “apply configuration
changes”
Choose SIP Trunk
-82-
15.21
Federal Communications Commission (FCC) Statement
You are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.
15.105(b)
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired
operation of the device.
-83-
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
Loading...