Porta Phone TD900HDR User Manual

USER

1. Power ON/OFF

ON: Press and hold the power button till to BLUE LED light up.

Power
Power OFF: Press and hold the power button till to the RED LED flashing.

2. Pairing/Register mode

a). Press and hold the power button to turn headset power ON, the power LED should

blinking in BLUE color.

b). Press the volume down button at 3 times continually, then press and hold the

he (REMOTE) RED and Blue LED blinking at alternately or (MASTER)

volume up

RED LED blinking.
c). Press the power ON/OFF switch of Master headset to select register to Line(Group) 1,
Line 2 or Line 3.

LINE condition indicate: Line 1: RED LED blinking; Line 2: BLUE LED blinking; Line 3:

ORANGE LED blinking.

d). The LED of Remote headset will turn RED after paired, press the power button to quit

till to t

MENU

the pairing mode.
e). Repeat the above step “a” to “d” for more Remote headset register on same Master,
press the power

button to finish the register.

①

(Note:

Line 2 communication in duplex, total register number over 250 headset available on Line

3 but listening only after the 8

②. The the power ON/OFF switch of Master headset for select the Line(GROUP) of the

headset connection. Press power ON/OFF button to select the headset register under the

Line(Group) 1, 2 or Line3 (Line 3 for listening only).

3. Talking and listening

a). The master and remote headset will start to search each other after powerON,theBLUE
LED flash 1 time each 3 seconds. The headset will be link together automatically when the
pairing ID confirmed by master and LED turn ON in blue color.

b). Press the volume up

. The Master

headset can accept maximum 8 remote register in line 1 (Group) and

th

and down

setregisteredonLine1and2.

head

button to

adjust speaker sound volume.

c).
separate the Line (Group) 1, 2 or make all conference.
d). The side switch of Remote headset for select the connection to Line(Group) 1 or
Line(Group) 2.

4. Mic Muted

Swivel up the Mic boom to MUTE the microphone and swivel down to back the normal
talking.

The s

ide

switch of Master headset for CONFERENCE ON/OFF. Press the switch to

FCC W

arning:

This device c

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

Any C

the user's authority to operate the equipment.



Exposur

This is a radio transmitter and receiver. It is designed and manufactured not to exceed the

emission limitsfor exposure to radio frequency (RF) energy set by the Federal

Communications Commission (FCC) of the U.S.Government. These limits are part of

comprehensive guidelines and establish permitted levels of RF energy for the general

population. The guidelines are based on the safety standards previously set by both U.S. and

international standards bodies. These standards include a substantial safety margin designed

to assure the safety of all persons,regardless of age and health. This device and its antenna

must not be co-located or operating in conjunction with any other antenna or transmitter. This

product has been shown to be capable of compliance for localized specific absorption rate

(SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE

Std. C95.1-1992 and

omplies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

hanges or modifications not expressly approved by the party responsible for compliance could void

e to

Radio Fre

qu

ency (RF) Signals

ad been tested in accordance with the measurement procedures

h

ISEDC Warning:

This device complies with ISEDC licen



following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence.L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

The device has been tested and compliance with SAR limits, users can obtain Canadian

information on RF exposure and compliance

Le présent appareil est conforme Après examen de ce matériel aux conformité aux limites

DAS et/ou aux limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux

radiofréquences et la conformité and compliance d’acquérir

ISEDC Radiation Exposure Statement:

SAR l’utilisation des règles sma l’emplacement Le matériel de transmission et

fonctionnant dans tous les essais à la

décidé le niveau, utilisation spécifique peut être très en deçà de la valeur de référence

maximale.Types de matériel sont vendus au public un ancien, d’essai et de certification

de l’exposition, limite maximum sma, chaque document et l’emplacement du matériel

d’essai et conformément au document.Le modèle en physique, matériel d’essai et

conforme aux directives d’exposition des radiofréquences sma quand une annexe

désigné pour ce produit lors de leur utilisation ou des pièces de rechange ne contiennent

pas de métal.

ce-exempt RSS standard(s). Operation is subject to the

certification, même si la puissance suprême a