Porta Phone TD900HDM User Manual

USER MENU

1. Power

Power ON: Press and hold the power button till to BLUE LED light up.
Power OFF: Press and hold the power button till to the RED LED flashing.

2. Pairing/Register mode

a). Press and hold the power button to turn headset power ON, the power LED should

c). Press the power ON/OFF switch of Master headset to select register to Line(Group) 1,
Line 2 or Line 3.

d). The LED of Remote headset will turn RED after paired, press the power button to quit

e). Repeat the above step “a” to “d” for more Remote headset register on same Master,

ON/OFF

blinking in BLUE color.

b). Press the volume down button at 3 times continually, then press and hold the

o the (REMOTE) RED and Blue LED blinking at alternately or (MASTER)

volume up
RED LED blinking.

LINE condition indicate: Line 1: RED LED blinking; Line 2: BLUE LED blinking; Line 3:

ORANGE LED blinking.

the pairing mode.

till t

press the power

button to finish the register.

①

he Master headset can accept maximum 8 remote register in line 1 (Group) and

(Note:

Line 2 communication in duplex, total register number over 250 headset available on Line

3 but listening only after the 8

②. The the power ON/OFF switch of Master headset for select the Line(GROUP) of the

headset connection. Press power ON/OFF button to select the headset register under the
Line(Group) 1, 2 or Line3 (Line 3 for listening only).

3. Talking and listening

a). The master and remote headset will start to search each other after powerON,theBLUE
LED flash 1 time each 3 seconds. The headset will be link together automatically when the
pairing ID confirmed by master and LED turn ON in blue color.

b). Press the volume up
c).

The

separate the Line (Group) 1, 2 or make all conference.

. T

th

adsetregisteredonLine1and2.

he

butto

and d

own

side switch of Master headset for CONFERENCE ON/OFF. Press the switch to

n to adjust speaker sound volume.

d). The side switch of Remote headset for select the connection to Line(Group) 1 or
Line(Group) 2.

4. Mic Muted

Swivel up the Mic boom to MUTE the microphone and swivel down to back the normal
talking.

CC Warning:

F

This

device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

A

ny Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.



Exposur

This is a radio transmitter and receiver. It is designed and manufactured not to exceed the
emission limitsfor exposure to radio frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S.Government. These limits are part of
comprehensive guidelines and establish permitted levels of RF ene rgy for the general
population. The guidelines are based on the safety standards previously set by both U.S. and
international standards bodies. These standards include a substa ntial safety margin designed
to assure the safety of all persons,regardless of age and health. This device and its antenna
must not be co-located or operating in conjunction with any other antenna or transmitter. This
product has been shown to be capable of compliance for localized specific absorption rate
(SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE
Std. C95.1-1992 and

e to Radio Frequency (RF) Signals

ad

h

been tested in accordance with the measurement procedures

ISEDC Warning:

This devi



following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
The device has been tested and compliance with SAR limits, users can obtain Canadian
information on RF exposure and compliance
Le présent appareil est conforme Après examen de ce matériel aux conformité aux limites
DAS et/ou aux limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition au x
radiofréquences et la conformité and compliance d’acquérir

ISEDC

SAR l’utilisation des règle
fonctionnant dans tous les essais à la certification, même si la puissance suprême a

décidé le niveau, utilisation spécifique peut être très en deçà de la valeur de référence
maximale.Types de matériel sont vendus au public un ancien, d’essai et de certification
de l’exposition, limite maximum sma, chaque document et l’emplacement du matériel
d’essai et conformément au document.Le modèle en physique, matériel d’essai et
conforme aux directives d’exposition des radiofréquences sma quand une annexe
désigné pour ce produit lors de leur utilisation ou des pièces de rechange ne contiennent
pas de métal.

ce complies with ISEDC licence-exempt RSS standard(s). Operation is subject to the

Radiation Exposure Statement:

s sma l’emplacement

matériel de transmission et

Le