RF1G9V1 Module
User Manual
Introduction
RF1G9V1 Module is a DECT (Digital Enhanced Cordless Telecommunications) compatibility products. To the
quality of audio and to the safety offered from the digital technology, It’s offers manifold and useful features
including Full duplex system. The module be application to cordless phone, walkie talkie and other data
communications.
Dimension Drawing
Outside view
Page 1
Block Diagram
,
RF1G9
Pin1-7
Synch-Interface
Syn_clk
Syn_data
RU1
DE19RF19
RFIC Transceiver
EXT-CLK
13.824MHz
Synch-Interface
Pin1- syn_out
Pin2- syn_en
Pin3- syn_clk
Pin4- syn_data
Pin5- slot_ctrl
Pin6- radio_en
Pin7- trdata
Pin8- vcc_dig
Pin9- rstn
Pin10,12-15,17,19-20,22-25,27,30-31.-GND
Pin11- vccrf
Pin16- vccPA
Pin18- A_ctrl2
Pin21- ANT
Pin26- A_ctrl1
Pin28- vccrf
Pin29- bclk
TX Part
RC16,21,24
27,28,63,64,
5
RL4
RX Part
RC4,5,14,15
RL2,3,7,8
RD1
TX,RX
Switch
Page 2
Specificatio
n
Standard DECT6.0 (Digital Enhanced Cordless Telecommunications)
Frequency
Frequency
Channel Separation
Modulation type
Transm
ission speed 1.152 Mbps (Baud rate)
Duplexing
Speech enco
ding ADPCM / 32kbit/s
RF Accessing
TX Power
Not more than 20dBm
Channel 5(USA),
Coverage range
Power Supply
mal condition of use 0
Nor
Storage Temperature
1920 ~1930MHz (USA)
1880 ~1900MHz (EURO)
1.728 MHz
GFSK
Time Division Duplex (TDD)
Time Division Multiple Access (TDMA)
10(EURO)
100m indoor; 400m in open space(PP to FP)
DC 3.3V/ 30-80mA
O
C to 40 O C
O
-10
C to 60 O C
LIMITED W
This lim
ARRANTY
ited warranty only applies to the use of this device with a communications service for which it
is designed. This device alone does not provide the customer with any communications service and
requires a separate subscription to a communications service from a service provider. Altering
service provider-specific settings may void the warranty. This limited warranty does not warrant that
the device will be free of any limitations of voice quality or service caused by (1) the services provided
by the customer’s underlying communications service provider; or (2) interference from other radio
frequencies or transmissions, static electricity, and other electronic devices.
FCC Cautio
n:
Any Chang
authority to operate the equipment.
This device complie
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of
the end product, which integrates this module
The final end product must be labeled in a visible area with the following” Contains
FCC ID:B4HRF190
The module supports the highest gain of antenna is 2.0dBi when install to the end product.
FCC Radiation Exposure S
This eq
equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
es or modifications not expressly approved by the party responsible for compliance could void the user's
s with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
0V1
tatement:
uipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This
ge 3
Pa
IC Warning:
This device complies w
to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
ith Industry Canada licence-exempt RSS standard(s). Operation is subject
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
(2
susceptible d'en compromettre le fonctionnement.
This equipment complies with IC radiation exposure
equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
Le présent appareil
Après examen de ce matériel aux conformité ou aux limites d’intensité de champ RF,
les utilisateurs peuvent sur l’exposition aux radiofréquences et la conformité and compliance d’acquérir
les informations correspondantes.
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of
the end product, which integrates this module
The final end product must be labeled in a visible area with the following”
est conforme
La distance minimale d
limits set forth for an uncontrolled environment .This
u corps à utiliser le dispositif est de 20cm.
contains IC:3064A-RF1900V1.
The module supports the highest gain of antenna is 2.0dBi when install to the end product.
Assemble to main board
The RF module can put on the main board by SMT or hand soldering.
Pa
ge 4
Loading...