Pool Lift Company Power EZ F-03PEZ, Power EZ F-333PEZNA User Manual
9889 Garrymore Ln
Missoula, MT 59808
888-687-3552 | +1-406-549-0769
www.aquacreek.com
1.
Power EZ
Pool Lift
PART #: F-03PEZ (with anchor)
PART #: F-333PEZNA (without anchor)
400 LB. [181 kg] MAXIMUM WEIGHT CAPACITY
MANDATORY
LEAVE THIS MANUAL WITH LIFT OWNER
Read and follow all instructions.
Lift safety can only be ensured if the lift is installed and
operated according to these instructions.
• NEVER permit children to play on or around the lift
• Do not allow children to use the lift without adult
superivsion
• NEVER apply direct water pressure to the electronics
• NEVER use the lift with a dry pool
READ CAREFULLY
Check entire box and all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the fi gures and parts listed in this document.
It is critical that all parts be carefully inspected prior to installation. If any damage occurred in
transit, Aqua Creek Products, LLC must be notifi ed within three days of receipt of unit.
Proper installation cannot be overstressed, as an improper installation voids Aqua Creek’s
warranty and may affect the safety of the user.
Copyright © 2016 Aqua Creek Products All Rights Reserved
The Pool Lift Company
The Pool Lift Company
The Pool Lift Company T: +44 (0)1256 896000 E: info@poollifts.co.uk W: www.poollifts.co.uk
1
Revised 2/24/16
Power EZ Lift
Table of Contents
PAGE DESCRIPTION PAGE DESCRIPTION
2 Power EZ Components 9 Basic Troubleshooting
3-4 Anchor Installation: Retro-Fit 10 Proper Care of Pool/Spa Lift
5 Anchor Installation: New Construction 11 Parts List
2.
6-7 Assembly Instructions 12
Warranty
8 Operating Instructions 13 Accessories and Options
Power EZ Components
The Power EZ lift will arrive partially assembled in multiple boxes. Begin by removing all parts from
the boxes and locating the parts for your lift in the parts lists below. Refer to the parts breakdown
drawings in the back of this manual for assistance.
BOOM ARM
ASSEMBLY
CONTROL BOX
& BATTERY
COVER
HANDSET
CONTROL
EZ HANGER
BAR
EZ CHAIN
SET
BOX ‘A’ CONTENTS
ITEM # QTY DESCRIPTION
1 1 POWER EZ BOOM ARM & MAST
BOX ‘B’ CONTENTS
MAST ASSEMBLY
EZ TURN-BAR
24V BATTERY
24V CONTROL
BOX
BATTERY
CHARGER
EZ SLING
LINEAR ACTUATOR
EZ ANCHOR
2
The Pool Lift Company T: +44 (0)1256 896000 E: info@poollifts
Copyright © 2016 Aqua Creek Products All Rights Reserved
ITEM # QTY DESCRIPTION
1 1 24 VOLT CONTROL BOX
2 1 24 VOLT BATTERY CHARGER
3 1 HARDWARE BAG
4 1 HANDSET CONTROL
5 1 24 VOLT BATTERY
6 1 EZ SLING [F-034EZS]
7 1 EZ CHAIN SET [F-031EZCH]
8 1 EZ HANGER [F-038EZHB]
9 4 EZ SLING BARS [F-032EZB]
10 1 LINEAR ACTUATOR [340461-00]
11 1 EZ TURN BAR [A-0808EZTB]
12 1 CB/BATTERY COVER [F-BCC-10-C]
13 2 3/8” X 1 3/4” HEX BOLT
14 2 3/8” NYLOCK NUT
15 4 3/8” FLAT WASHER
16 2 2 1/4” HOSE CLAMP
17 3 ZIP TIES
18 1 ANCHOR (IF ORDERED WITH LIFT)
19 1 OWNERS MANUAL
W: www.poollifts.co.uk
Revised 2/24/16
Anchor Installation: Retro-Fit Concrete
NOTE: The concrete deck around the
3.
TOOLS REQUIRED:
TAPE MEASURE 4” CORE DRILL BIT
CORE DRILL FELT TIP MARKING PEN
ELECTRICAL TAPE VACCUM OR COMPRESSED AIR
CARPENTERS LEVEL 2-PART EPOXY (or equivalent)
anchor should be a minimum of 8 inches
thick and reinforced with #4 bars at 10
inches on center, each way. The total
concrete pad area should be at least 60
inches wide and 60 inches long.
1. Determine the best location for the lift. Mount the lift at a location that provides 42 inches [107cm] to
48 inches [122cm] deck level to the bottom of the pool (usually the shallow end). Make sure the location
has enough clear deck space to easily transfer. The lift requires at least 6 feet [1.8 meters] of unobstructed
deck to each side of the lift to accomodate easy maneuvering of the lift over the water and back. Keep in
mind this lift will require assistance so locate an area that can accomodate another person.
2. Locate the concrete anchor socket that came with your lift. Be careful to not lose the protective cap
on the anchor as this will be used to keep dirt and debris out of the socket when the lift is not installed in
the anchor.
3. The setback to the center of the anchor must be no less than 12 inches [30.5cm] and no more than
36 inches [91cm] from the pool wall. The anchor location must also be at least 6 inches [15cm] from any
control joint or edge of concrete slab. Measure the location out using the tape measure and marking
pen. See FIGURE 1 on page 4 for details.
4. Core drill at least a 4 inch [10cm] diameter hole at the desired location for the lift anchor socket.
The hole will need to be 7 inches [18cm] deep to allow for the grounding lug which protrudes from the
bottom of the anchor.
NOTE: Use the electrical tape to make a mark on your drill bit at 7 inches [18cm] as a depth mark to
tell you when to stop drilling.
5. Clean out the hole using a vaccum or compressed air. Check that the hole is deep enough to allow
the anchor to be ush with the nished deck surface.
6. Ground the anchor according to your local code requirements. This may require additional drilling
and/or other tools.
The Pool Lift Company T: +44 (0)1256 896000 E: info@poollifts.co.uk W: www.poollifts.co.uk
Copyright © 2016 Aqua Creek Products All Rights Reserved
3
Revised 2/24/16
Anchor Installation: Retro-Fit
4.
7. Carefully insert the anchor into the hole. Pour a small amount of 2 part epoxy, or equivalent, around
the anchor. Check that the anchor will sit level or ush with the nished deck surface.
NOTE: Fill the hole about 1/3 full of 2 part epoxy, or equivalent, prior to inserting the anchor. As
you insert the anchor, rotate it back and forth so that you can evenly distribute the cement
or epoxy around the anchor.
8. Once anchor is level and ush with deck, pour cement or epoxy into the remaining space around
the anchor making sure there are no void spaces. Let cement or epoxy cure for 24 hours (or minimum
manufacturer’s recommendations) before installing and using lift.
[30.5 cm] 12" MIN
[91 cm]
36"
MAX
ANCHOR SOCKET
42"
TO
48"
[15 cm]
6" MIN
C
L
GROUNDING LUG
CEMEMNT/EPOXY
TOP OF SLAB
[20.3cm]
8" MIN.
4
Copyright © 2016 Aqua Creek Products All Rights Reserved
The Pool Lift Company T: +44 (0)1256 896000 E: info@poollifts.co.uk W: www.poollifts.co.uk
FIGURE 1
Revised 2/24/16
Loading...