POOLEX 90, 150, 120, 200 Installation And User Manual

Download

INSTALLATION

AND

USER MANUAL

for your heat pump

Models 90 / 120 / 150 / 200

Dear Customer,

Thank you for your purchase and for your condence in our products.

These are the result of many years of research in the eld of design and production of heat pumps for swimming pools. Our aim is to provide you with an exceptional high performance quality product.

We have produced this manual with the utmost care so that you get maximum benet from your Poolex heat pump.

Thank you

PLEASE READ CAREFULLY.

These installation instructions are an integral part of the product.

They must be given to the installer and retained by the user.

If the manual is lost, please consult the website:

www.poolex.fr

The instructions and recommendations contained in this manual should be read carefully and understood since they provide valuable information concerning the heat pump’s safe handling and operation. Keep this

manual in an accessible place for easy future reference.

Installation must be carried out by a qualied professional person in accordance with current regulations and the manufacturer’s instructions. An installation error may cause physical injury to persons or animals as well as mechanical damage for which the manufacturer can under no circumstances be held responsible.

After unpacking the heat pump, please check the contents in order to report any damage. Please also check that the pressure indicated on the gauge is higher than 80 psi. If not, this could mean a leak of refrigerant.

Prior to connecting the heat pump, ensure that the information provided in this manual is compatible with the actual installation conditions and does not exceed the maximum limits authorised for this particular product.

In the event of a defect and/or malfunction of the heat pump, the electricity supply must be disconnected and no attempt made to repair the fault.

Repairs must be undertaken only by an authorised technical service organisation using original replacement parts. Failure to comply with the above-mentioned clauses may have an adverse effect on the heat pump’s safe operation.

To guarantee the heat pump’s efciency and satisfactory operation, it is important to ensure its regular

maintenance in accordance with the instructions provided.

If the heat pump is sold or transferred, always make sure that all technical documentation is transmitted with the equipment to the new owner.

This heat pump is designed solely for heating a swimming pool. Any other use must be considered as being inappropriate, incorrect or even hazardous.

! !

Any contractual or non-contractual liability of the manufacturer/distributor shall be deemed null and void for damage caused by installation or operational errors, or due to non-compliance with the instructions provided in this manual or with current installation norms applicable to the equipment covered by this document.

Contents

1. General ............................................................................................................................................................................................ 6

1.1 General Terms of Delivery ......................................................................................................................................................... 6

1.2 Safety instructions....................................................................................................................................................................... 6

1.3 Water treatment ......................................................................................................................................................................... 7

2. Description ...................................................................................................................................................................................... 8

2.1 Package contents ...................................................................................................................................................................... 8

2.2 General characteristics .............................................................................................................................................................. 8

2.3 Technical specications .............................................................................................................................................................. 9

2.4 Unit dimensions ........................................................................................................................................................................ 10

2.5 Exploded view ............................................................................................................................................................................11

3. Installation..................................................................................................................................................................................... 12

3.1 Pre-requirements ...................................................................................................................................................................... 12

3.2 Location .................................................................................................................................................................................... 12

3.3 Installation layout ...................................................................................................................................................................... 13

3.4 Connecting the condensation draining kit ................................................................................................................................. 13

3.5 Installing the unit on noise-damping supports........................................................................................................................... 13

3.6 Hydraulic connection................................................................................................................................................................. 14

3.7 Electrical installation ................................................................................................................................................................. 16

3.8 Electrical connection ................................................................................................................................................................ 17

3.9 Wall–mounting the remote control ........................................................................................................................................... 18

4. Use ................................................................................................................................................................................................. 19

4.1 Wired remote control................................................................................................................................................................. 19

4.2 Operating mode selector........................................................................................................................................................... 19

4.3 Heating Mode............................................................................................................................................................................ 20

4.4 FIX Heating Mode ..................................................................................................................................................................... 21

4.5 ECO Heating Mode ................................................................................................................................................................... 22

4.6 Cooling Mode ............................................................................................................................................................................ 23

4.7 Setting the clock ....................................................................................................................................................................... 24

4.8 Programming Start/Stop ........................................................................................................................................................... 25

4.9 Activating a programme ........................................................................................................................................................... 26

4.10 Deactivating a programme ....................................................................................................................................................... 26

4.11 Status values ............................................................................................................................................................................ 27

4.12 System parameter query........................................................................................................................................................... 28

4.13 Forced de-icing function............................................................................................................................................................ 29

5. Operation....................................................................................................................................................................................... 30

5.1 Operation .................................................................................................................................................................................. 30

5.2 Servo-control of circulating pump ............................................................................................................................................. 30

5.3 Using the pressure gauge ......................................................................................................................................................... 31

5.4 Antifreeze protection ................................................................................................................................................................. 31

6. Maintenance and servicing.......................................................................................................................................................... 32

6.1 Maintenance and servicing ....................................................................................................................................................... 32

6.2 Winter storage .......................................................................................................................................................................... 33

7. Repairs .......................................................................................................................................................................................... 34

7.1 Breakdowns and faults.............................................................................................................................................................. 34

7.2 List of faults ............................................................................................................................................................................... 35

8. Recycling....................................................................................................................................................................................... 36

8.1 Recycling the heat pump .......................................................................................................................................................... 36

9. Warranty ........................................................................................................................................................................................ 37

9.1 General warranty conditions ..................................................................................................................................................... 37

10. Appendices ................................................................................................................................................................................. 38

10.1 Wiring diagrams ....................................................................................................................................................................... 38

All equipment, even if shipped ‘free of carriage and packing’, is dispatched at the consignee’s own risk

The person responsible for receiving the equipment must carry out a visual inspection to identify any damage to the heat pump during transport (refrigerant system, body panels, electrical control box, frame). He/ she must note down on the carrier’s delivery note any remarks concerning damage caused during transport

and conrm them to the carrier by registered letter within 48 hours.

The equipment must always be stored and transported vertically on a pallet and in its original packaging. If

it is stored or transported horizontally, wait at least 24 hours before switching it on.

During installation and servicing

Only a qualied person may undertake installation, start-up, servicing and repairs, in compliance with

current standards.

Before operating or undertaking any work on the equipment (installation, commissioning, usage, servicing), the person responsible must be aware of all the instructions in the heat pump’s installation manual as well

as the technical specications.

Under no circumstances install the equipment close to a source of heat, combustible materials or a building’s air intake.

If installation is not in a location with restricted access, a heat pump protective grille must be tted.

To avoid severe burns, do not walk on pipework during installation, repairs or maintenance.

To avoid severe burns, prior to any work on the refrigerant system, turn off the heat pump and wait several minutes before placing temperature and pressure sensors.

Check the refrigerant level when servicing the heat pump.

Check that the high and low pressure switches are correctly connected to the refrigerant system and that they turn off the electrical circuit if tripped during the equipment’s annual leakage inspection.

Check that there is no trace of corrosion or oil stains around the refrigerant components.

1.2 Safety instructions

1.1 General Terms of Delivery

WARNING:

Please read carefully the safety instructions before using the equipment.

The following instructions are essential for safety so please strictly comply with them.

1. General

1.3 Water treatment

Poolex heat pumps for swimming pools can be used with all types of water treatment systems. Nevertheless, it is essential that the treatment system (chlorine, pH, bromine and/or salt chlorinator metering pumps) is installed after the heat pump in the hydraulic circuit.

To avoid any deterioration to the heat pump, the water’s pH must be maintained between 6.9 and

8.0.

1. General

During use

To avoid serious injuries, never touch the fan when it is operating.

Keep the heat pump out of the reach of children to avoid serious injuries caused by the heat exchanger’s blades.

Never start the equipment if there is no water in the pool or if the circulating pump is stopped.

Check the water ow rate every month and clean the lter if necessary.

During cleaning

Switch off the equipment’s electricity supply.

Close the water inlet and outlet valves.

Do not insert anything into the air or water intakes or outlets.

Do not rinse the equipment with water.

During repairs

Carry out work on the refrigerant system in accordance with current safety regulations.

Brazing should be performed by a qualied welder.

When replacing a defective refrigerant component, use only parts certied by our technical department.

When replacing pipework, only copper pipes conforming to Standard NF EN12735-1 may be used for repairs.

When pressure-testing to detect leaks:

To avoid the risks of re or explosion, never use oxygen or dry air.

Use dehydrated nitrogen or a mixture of nitrogen and refrigerant.

The low and high side test pressure must not exceed 42 bar.

2.1 Package contents

2.2 General characteristics

✔ Heat pump Poolex Jetline Premium Inverter

✔ 2 hydraulic inlet/outlet connectors (50mm diameter)

✔ Extension cable for remote control panel

✔ This installation and user manual

✔ Condensation draining kit

✔ Winter storage cover

✔ 4 anti-vibration pads (fastenings not supplied)

A Poolex heat pump has the following features:

CE certication and complies with the RoHS European directive.

High performance with up to 80% energy savings compared to a conventional heating system.

Clean, efcient and environmentally friendly R410A refrigerant.

Reliable high output leading brand compressor.

Wide hydrophilic aluminium evaporator for use at low temperatures.

User-friendly intuitive remote control.

Heavy duty ABS shell, anti-UV treated and easy to maintain.

Designed to be silent.

Dual antifreeze system to avoid frost damage:

Revolutionary exchanger with patented antifreeze system.

A smart monitoring system to preserve the pipework and liner without emptying the pool in winter.

2. Description

Poolex Jetline Premium Inverter

Test conditions

90 120 150 200

Air

(1)

26°C

Water

(2)

26°C

INVERTER MODE

Heating power (kW) 12.2~2.78 15.1~3.47 20.3~4.67 28.0~6.45

Consumption (kW) 1.79~0.209 2.22~0.261 3.01~0.354 4.11~0.485

COP (Coeff. of performance) 13.3~6.8 13.3~6.8 13.2~6.75 13.3~6.8

Air

(1)

26°C

Water

(2)

26°C

SILENCE MODE

Heating power (kW) 8.8~2.78 10.6~3.47 14.21~4.67 19.6~6.45

Consumption (kW) 1.11~0.209 1.34~0.261 1.81~0.354 2.48~0.485

COP (Coeff. of performance) 13.3~7.9 13.3~7.9 13.2~7.85 13.3~7.9

Air

(1)

15°C

Water

(2)

26°C

INVERTER MODE

Heating power (kW) 9.03~2.09 12.1~2.77 15.1~3.45 20.1~4.62

Consumption (kW) 1.86~0.286 2.49~0.379 3.13~0.479 4.16~0.633

COP (Coeff. of performance) 7.3~4.83 7.3~4.85 7.2~4.83 7.3~4.83

Air

(1)

15°C

Water

(2)

26°C

SILENCE MODE

Heating power (kW) 6.37~2.09 8.4~2.77 10.56~3.45 14.08~4.62

Consumption (kW) 1.15~0.286 1.53~0.379 1.92~0.479 2.56~0.633

COP (Coeff. of performance) 7.3~5.5 7.3~5.5 7.2~5.5 7.3~5.5

Air

(1)

15°C

Water

(2)

26°C

FIX MODE

Heating power (kW) 6,01 8,01 9,5 13,01

Consumption (kW) 1,06 1,425 1,69 2,31

COP (Coeff. of performance) 5,62 5,62 5,61 5,62

Air

(1)

35°C

Water

(2)

27°C

Cooling capacity (kW) 4.8~2.7 6.5~4.01 7.9~4.9 10.5~6.9

Consumption (kW) 1.41~0.586 1.91~0.87 2.32~1.07 3.09~1.5

Avg. EER (Energy Efciency Ratio) 4.6~3.4 4.6~3.4 4.58~3.4 4.6~3.4

Maximum power (kW) 3,202 4,004 5,005 6,01

Maximum current (A) 7,5 10,1 12,5 16,1

Electricity supply 220~240V / 50Hz

Protection IPX4

Heating temperature range 15°C~40°C

Cooling temperature range 8°C~28°C

Operating temperature range -10°C~43°C

Unit dimensions L x W x H (mm) 950 x 355 x 650

1055 x 395 x 703

Unit weight (kg) 56 60 65 73

Sound pressure level at 1 m (dBA)

(3)

40~48 41~50 42~51 43~52

Sound pressure level at 10 m (dBA)

(3)

21~29 23~31 24~32 24~33

Hydraulic connection (mm) PVC 50mm

Heat exchanger PVC tank and titanium heating coil

Min. water ow rate (m³/h) 3.3 / 8.5 4.4 / 10.3 5.2 / 12.5 7.1 / 16.1

Compressor Mitsubishi Mitsubishi Mitsubishi Mitsubishi

Compressor type Twin Rotary Twin Rotary Twin Rotary Twin Rotary

Refrigerant R410A

Refrigerant content (kg) 0.9 1.05 1.2 1.6

GWP 2088 2088 2088 2088

CO2 equivalent 1.88 2.19 2.51 3.34

Load loss (mCE) 1,1 1,1 1,1 1,2

Max. pool volume (m3)

(4)

≤60 ≤75 ≤95 ≤130

Remote control Wired backlit LCD monitor screen

Mode Heating / Cooling

2.3 Technical specications

2. Description

The technical specications of our heat pumps are provided for information purposes only. We reserve the right to make changes without prior notice.

Ambient air temperature

Initial water temperature

Noise at 1 m, at 4 m and at 10 m in accordance with Directives EN ISO 3741 and EN ISO 354

Calculated for an in-ground private swimming pool covered with a bubble cover.

2.4 Unit dimensions

2. Description

Dimensions in mm

Model Jetline Premium Inverter 90 / 120 / 150 Jetline Premium Inverter 200

A 650 702.5

B 950 1053

C 350 395

D 317 370

E 154 182.5

F 610 620

G 154 217.5

H 91 101

I 330 380

J 22 20

K 12 5

E F

H I

2.5 Exploded view

2. Description

1. Front panel

2. Fan blade

3. Fan motor

4. Left panel

5. Evaporator

6. Top panel

7. Electrical box cover

8. Electrical box

9. Pressure gauge

10. Controller

11. Wiring terminal

12. Terminal cover

13. Right panel

14. Heat exchanger

15. Electronic expansion valve

16. Reactive resistance

17. 4-way valve

18. Gas-liquid separator (only model 150 / 200)

19. Compressor

20. ON/OFF switch

Equipment necessary for the installation of your heat pump:

Power supply cable suitable for the unit’s power requirements.

A By-Pass kit and an assembly of PVC tubing suitable for your installation as well as stripper, PVC adhesive and sandpaper.

A set of wall plugs and expansion screws suitable to attach the unit to your support.

We recommend that you connect the unit to your installation by means of exible PVC pipes in order to

reduce the transmission of vibrations.

Suitable fastening studs may be used to raise the unit.

3.1 Pre-requirements

3.2 Location

Please comply with the following rules concerning the choice of heat pump location.

1. The unit’s future location must be easily accessible for convenient operation and maintenance.

2. It must be installed on the ground, xed ideally on a level concrete oor. Ensure that the oor is sufciently stable and can support the weight of the unit.

3. A water drainage device must be provided close to the unit in order to protect the area where it is installed.

4. If necessary, the unit may be raised by using suitable mounting pads designed to support its weight.

5. Check that the unit is properly ventilated, that the air outlet is not facing the windows of neighbouring

buildings and that the exhaust air cannot return. In addition, provide sufcient space around the unit for

servicing and maintenance operations.

6. The unit must not be installed in an area exposed to oil, ammable gases, corrosive products, sulphurous compounds or close to high frequency equipment.

7. To prevent mud splashes, do not install the unit near a road or track.

8. To avoid causing nuisance to neighbours, make sure the unit is installed so that it is positioned towards the area that is least sensitive to noise.

9. Keep the unit as much as possible out of the reach of children.

3. Installation

WARNING: Installation must be carried out by a qualied engineer. This section is provided for information purposes only and must be checked and adapted if necessary according to the actual installation conditions.

Place nothing less than one metre in front of the heat pump.

Leave 50 cm of empty space around the sides and rear of the heat pump.

Do not leave any obstacle above or in front of the unit!

Dimensions in mm.

3.3 Installation layout

3.4 Connecting the condensation draining kit

3.5 Installing the unit on noise-damping supports

While operating, the heat pump is subject to condensation. This will result in a more or less large run-off

of water, depending on the degree of humidity. To channel this ow, we recommend that you install the

condensation drainage kit.

How do you install the condensation drainage kit|?

Install the heat pump, raising it at least 10 cm with solid water-resistant pads, then connect the drainage pipe to the opening located under the pump.

In order to minimise the noise pollution associated with heat pump vibrations, it can be positioned on vibration absorbing pads.

To do this, you simply have to position a pad between each of the unit’s feet and its support, and then x

the heat pump to the support with suitable screws.

3. Installation

Valves 1, 2 and 3: Bypass valves Valves 4 and 5: Regulating valves

(Recommended for facilitating adjustments close to the machine)

Half-open valve Open valve

Key

Heat pump

Water outlet

Water intake

Elevating

studs

Drain

plug

Condensation

draining

Valve 4

Valve 5

Valve 3 Valve 2

Circulating pump

Filtration

Valve 1

Automated treatment system (salt chlorinator, metering pump)

TOWARDS THE POOL

FROM THE POOL

4-way valve

Making a hydraulic connection with the By-Pass kit

Step 1: Take the necessary steps to cut your pipes.

Step 2: Make a straight perpendicular cut through the PVC pipes with a saw.

Step 3: Assemble your hydraulic circuit without connecting it in order to check that it perfectly ts your

installation, then dismantle the pipes to be connected.

Step 4: Chamfer the ends of the cut pipes with sandpaper.

Step 5: Apply stripper to the ends of the pipes to be connected.

Step 6: Apply the adhesive in the same place.

Step 7: Assemble the pipes.

Step 7: Clean off any adhesive remaining on the PVC.

Step 8: Leave to dry for at least 2 hours before putting the hydraulic circuit into water.

3.6 Hydraulic connection

3. Installation

WARNING: Do not run water through the hydraulic circuit for 2 hours after applying the adhesive.

By-Pass assembly

The heat pump must be connected to the pool by means of a By-Pass assembly.

A By-Pass is an assembly consisting of 3 valves that

regulate the ow circulating in the heat pump.

During maintenance operations, the By-Pass permits the heat pump to be isolated from the system without interrupting your installation.

TOWARDS THE POOL

Open valve

Half-open valve

FROM THE POOL

By-Pass assembly for more than one heat pump

By-Pass assembly for one heat pump

The lter located upstream of the heat pump must be regularly cleared so that the water in

the system is clean, thus avoiding the operational problems associated with dirt or clog-

ging in the lter.

3. Installation

Half-open valve

Open valve

Key

TOWARDS THE POOL

Filtration + Pump

Automated treatment system

TOWARDS THE POOL

FROM THE POOL

POOL

FROM THE POOL

3. Installation

To function safely and maintain the integrity of your electrical system, the unit must be connected to a general electricity supply in accordance with the following regulations:

Upstream, the general electricity supply must be protected by a 30 mA differential switch.

The heat pump must be connected to a suitable D-curve circuit breaker (see table below) in accordance with current standards and regulations in the country where the system is installed.

The electricity supply cable must be adapted to match the unit’s rated power and the length of wiring required by the installation (see table below). The cable must be suitable for outdoor use.

For a three-phase system, it is essential to connect the phases in the correct sequence. If the phases are inverted, the heat pump’s compressor will not work.

In places open to the public, it is mandatory to install an emergency stop button close to the heat pump.

Models Electricity supply Max. current

Cable diameter

Protection

Thermal-magnetic (D

curve) protection

Jetline Premium Inverter 90

1-phase

220-240V/1N~50Hz

14.4 A RO2V 3x2,5 mm² 16 A

Jetline Premium Inverter 120

18 A RO2V 3x4 mm² 20 A

Jetline Premium Inverter 150

22.5 A RO2V 3x4 mm² 25 A

Jetline Premium Inverter 200

27 A RO2V 3x6 mm² 32 A

Cable cross-section suitable for max. length 10 metres. For longer than 10 metres, consult an electrician.

3.7 Electrical installation

Please comply with the following instructions to electrically connect the heat pump.

Step 1: Detach the electrical side panel with a screwdriver to access the electrical terminal block.

Step 2: Insert the cable into the heat pump unit by passing it through the opening provided for that purpose.

Step 3: Connect the power supply cable to the terminal block in accordance with the diagram below.

Step 4: Carefully close the heat pump panel.

Servo-control of circulating pump

Depending on the type of installation, you can also connect a circulating pump to terminals P1 and P2 so that this operates in tandem with the heat pump.

3. Installation

3.8 Electrical connection

WARNING: The heat pump’s power supply MUST be disconnected before any operation.

WARNING: Servo-control of a pump whose power exceeds 5A (1000W) requires the use of a power relay.

L N P1 P2

Connecter à l’alimentation

230V / 50Hz

Connecter à la

pompe à filtration

ou un relais de puissance

PHASE NEUTRE TERRE PHASE NEUTRE

Single phase model

Connect to power supply

230V / 50Hz

PHASE NEUTRAL NEUTRALEARTH PHASE

Connect to a ltration

pump or a power

relay

P1 P2

PHASE TERRENEUTRE

Connecter à la

pompe de circulation

ou un relais de puissance

C N

PHASE CPHASE BPHASE A NEUTRE TERRE

Connecter à l’alimentation

Triphasée

400V / 50Hz

3-phase model

PHASE NEUTRAL EARTHPHASE A PHASE B PHASE C NEUTRAL EARTH

Connect to power supply

3-phase

400V/50Hz

Connect to a ltration

pump or a power relay

3.9 Wall–mounting the remote control

Step 1: Detach the remote control from the machine. Pay attention to the communication wire connected to the printed circuit board and separate them carefully.

Step 2: Use a screwdriver to open the casing and separate the remote control.

Step 3: Drill two parallel holes at eye level: 60 mm centre-to-centre.

Step 4: Attach the remote control’s rear cover to the wall.

Step 5: Align the front and rear covers exactly, ensuring that the box is xed rmly to the wall.

Step 6: Carefully connect the communication wire.

WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you may

damage it. When the remote control is xed to the wall, do not pull the communication wire, this may cause a loose contact.

3. Installation

Step 1

Step 4

Step 2

Step 5

Step 3

Step 6

60mm

4.2 Operating mode selector

Prior to setting your required temperature, you must rst select an operating mode for your heat pump:

4. Use

4.1 Wired remote control

Before starting, ensure that the ltration pump is working and that water is circulating through

the heat pump.

Button: On/Off

Button: Clock and Timers

Button: Operating mode

Water temperature

Outside temperature

Clock

Operating mode

FIX Mode (Heating only)

Select the x heating mode for the heat pump to heat the water in your pool constant power.

Heating Mode (inverter)

Select the heating mode for the heat pump to heat the water in your pool intelligently.

Cooling Mode (inverter)

Select the cooling mode for the heat pump to cool the water in your pool intelligently.

ECO Silence Mode

Select the silence heating mode for the heat pump to heat the water at reduced speed.

When the incoming water temperature is less than or equal to the required temperature (setpoint temperature - 1°C), the heat pump will switch to heating mode. The compressor will stop when the temperature of the incoming water is greater than or equal to the required temperature (setpoint temperature + 1°C).

Step 1: Long press 3s to switch on your pump.

Step 2: Long press 3s to switch from one mode to another until the Heating Mode is displayed.

Step 3: Using buttons and select the required temperature (15-40°C).

4. Use

4.3 Heating Mode (inverter)

WARNING: Before starting, ensure that the ltration pump is operating correctly.

WARNING: When the cooling mode switches to heating mode or vice-versa, the heat pump will restart

after 10 minutes.

EXAMPLE: If you have selected 28°C, your screen will display:

Once the symbol stops blinking, the required temperature is validated and is replaced by the water’s current temperature (25° in our example).

Required

temperature“Blinking”

Current water

temperature

Current temperature

of the ambient air

Useful information

Step 1: Long press 3s to switch on your pump.

Step 2: Long press 3s to switch from one mode to another until the FIX Heating Mode is displayed.

Step 3: Using buttons and select the required temperature (15-40°C).

4.4 FIX Mode (heating only)

WARNING: Before starting, ensure that the ltration pump is operating correctly.

WARNING: When the cooling mode switches to heating mode or vice-versa, the heat pump will restart

after 10 minutes.

EXAMPLE: If you have selected 28°C, your screen will display:

Once the symbol stops blinking, the required temperature is validated and is replaced by the water’s current temperature (25° in our example).

Required

temperature“Blinking”

Current water

temperature

Current temperature

of the ambient air

4. Use

Useful information

WARNING: When the cooling mode switches to heating mode or vice-versa, the heat pump will restart after 10 minutes.

Step 1: Long press 3s to switch on your pump.

Step 2: Long press 3s to switch from one mode to another until ECO Heating Mode is displayed.

Step 3: Select the desired temperature by using the buttons and (15-40°C).

4. Use

4.5 ECO silence Mode

WARNING: Before starting, ensure that the ltration pump is operating correctly.

EXAMPLE: If you have selected 28°C, your screen will display:

Once the symbol stops blinking, the required temperature is validated and is replaced by the water’s current temperature (25° in our example).

Required

temperature“Blinking”

Current water

temperature

Current temperature

of the ambient air

Useful information

When the incoming water temperature is higher or equal to the required temperature (setpoint temperature + 1°C), the heat pump will switch to cooling mode. The compressor will stop when the temperature of the incoming water is less than or equal to the required temperature (setpoint temperature - 1°C).

Step 1: Long press 3s to switch on your pump.

Step 2: Long press 3s to switch from one mode to another until the Cooling Mode is displayed.

Step 3: Using buttons and select the required temperature (8-28°C).

WARNING: Before starting, ensure that the ltration pump is operating correctly.

4. Use

4.6 Cooling Mode (inverter)

WARNING: When the cooling mode switches to heating mode or vice-versa, the heat pump will restart after 10 minutes.

EXAMPLE: If you have selected 24°C, for example, your screen will display:

Once the symbol stops blinking, the required temperature is validated and is replaced by the water’s current temperature (27° in our example).

Required

temperature“Blinking”

Current water

temperature

Current temperature

of the ambient air

Useful information

Set the system clock to local time, as follows:

Step 1: Press to set the time, the hours are blinking.

Step 2: Adjust the hours with the buttons and .

Step 3: Press to switch to minutes.

Step 4: Adjust the minutes with the buttons and .

Step 5: Press to validate and return to the main screen.

4. Use

4.7 Setting the clock

Step 3Step 2

Step 5

Step 1

Step 4

This function is for programming the Start/Stop timing. You can programme up to 3 different Start/Stop timings. Setting is as follows:

Refer to the following section to activate the programme

Step 1: Long press 3s to enter into timer functions

Step 2: Select the programme to be congured with the buttons and .

Step 3: Press to programme the start time.

Step 4: Adjust the hours with the buttons and .

Step 5: Press to switch to minutes.

Step 6: Adjust the minutes with the buttons and .

Step 7: Press to programme the stop time.

Step 8: Adjust the hours with the buttons and .

Step 9: Press to switch to minutes.

Step 10: Adjust the minutes with the buttons and .

Step 11: Press to return to the main screen.

4. Use

4.8 Programming Start/Stop

NB: The remote control

returns automatically to the main screen after 10 seconds.

Step 3 Step 4Step 2Step 1

Step 7

Step 11

Step 8Step 6

Step 10

Step 5

Step 9

Once the programme has been dened, it can be activated as follows:

Once the programme has been activated, it can be deactivated as follows:

Step 1: Long press 3s to enter into timer functions

Step 2: Select the programme to be activated with the buttons and .

Step 3: Keep pressing until the ON/OFF indicator lights are displayed and start ashing.

Step 4: Press to return to the main screen.

The ON/OFF lights indicate an active programme; the numeral above the line indicates the number of the active

programme.

Step 1: Long press 3s to enter into timer functions

Step 2: Select the programme to be deactivated with the buttons and .

Step 2: Keep pressing until the ON/OFF indicator lights disappear

Step 3: Press to return to the main screen

The ON/OFF lights indicate an active programme; the numeral above the line indicates the number of the active

programme.

4. Use

4.9 Activating a programme

4.10 Deactivating a programme

Step 3

Step 4

Step 2

Step 1

The status values can be checked via the remote control by following these steps

Status values table

Step 1: Keep pressing until you enter the settings verication mode.

Step 2: Press and to check the status values.

Step 3: Press to return to the main screen.

4. Use

4.11 Status values

N° Description Range

01 Water inlet temperature -20~99°C

02 Water outlet temperature -20~99°C

03 Ambient temperature -20~99°C

04 Air outlet temperature 0~125°C

05 Air inlet temperature -20~99°C

06 Outside coid temperature -20~99°C

07 Inside coil temperature -20~99°C

08 The openness of the expansion valve

09 Reserved

10 Compressor current

11 Temperature of the heat sink

12 DC bus voltage

13 Compressor real speed

Step 3Step 2Step 1

4. Use

4.12 System parameter query

WARNING : This operation is used to assist servicing and future repairs.

The default settings should only be modied by an experienced professional person.

The system’s settings can be checked and adjusted via the remote control by following these steps

Parameters table

Step 1 : Keep pressing 3s on until you enter the settings verication mode.

Step 2 : Press and for see the congured parameters.

Step 3 : Press to select the setting to be modied, the value is blinking.

Step 4 : Press and to adjust the setting value.

Step 5 : Press to set the new value.

Step 6 : Press to return to the main screen.

If not opération for 60s, it will be exited automatically.

Step 3

Step 4

Step 2Step 1

«Blink»

Step 6Step 5

N° Description Adjustment range Factory setting Remarks

01* Adjustment of temperature difference befor restart 2~18°C 1°C Adjustable

02 Reserved - Do not adjust Reserved

03 Reserved - Do not adjust Reserved

04 Adjusting the cooling temperature 8~28°C 27°C Adjustable

05 Setting the heating temperature 15~40°C 27°C Adjustable

06 Ambient air protection temperature 80~125°C 120°C Adjustable

07 Compressor output protection temperature 50~100°C 95°C Adjustable

08 Compressor current protection 2~50A 20°C Adjustable

Setting the compensation coefcient of the temperature water inlet

-5~15°C 0°C Adjustable

10 Reserved - Do not adjust Reserved

11 Auto-activation time before de-icing commences 20~90 min 45 min Adjustable

WARNING : Any change to the reserved settings will automatically void the warranty.

4. Use

12 De-icing activation temperature -15~1°C -3°C Adjustable

13 Maximum de-icing duration 5~20 min 8 min Adjustable

14 De-icing deactivation temperature 1~40°C 20°C Adjustable

Difference before de-icing between air temp. and evaporator temp.

0~15°C 5°C Adjustable

16 Outside temperature before de-icing 0~20°C 17°C Adjustable

17 Reserved - Do not adjust 20~90 s 30 s Reserved

18 Reserved - Do not adjust -5~10°C 0°C Reserved

19 Reserved - Do not adjust 70~125°C 95°C Reserved

20 Reserved - Do not adjust 20~450 300 Reserved

21 Reserved - Do not adjust 50~150°C 100°C Reserved

22 Activation mode of expansion valve 0 - Manual ~ 1 - Auto 1 Adjustable

23 opening steps of expansion valve 20~450 350 Adjustable

24 Reserved - Do not adjust -5~10°C 3°C Reserved

25 Reserved - Do not adjust 20~450 350 Reserved

26 Reserved - Do not adjust 11~45°C 23°C Reserved

27 Reserved - Do not adjust

0 - Ambient

1 - overheat

1 Reserved

28**Filtration pump servo-control mode

0 - Normal 1 - Special

1 Adjustable

* Parameter 01 allows you to change the lost degree interval from the requested temperature so that the

heat pump starts again. Example : If the value of parameter 01 is 3 ° C, after reaching the required temperature (eg 27 °

C), the heat pump will restart when the pool temperature drops to 24 ° C (27 - 3).

* * Parameter 28: Control mode of the circulation pump

When you switch on your heat pump, the circulation pump starts and then 1 minute later, the heat pump compressor is activated. When the heat pump stops running, its compressor and fan shut off, and after 30 seconds, the circulation pump stops. During a defrost cycle, the circulation pump will continue to operate regardless of the mode chosen.

Mode 0 (normal mode) : By selecting this mode, the heat pump will automatically put the circulating pump into continuous operation. Once the circulating pump is operating, the heat pump will start up 1 minute later. Next, when the required temperature is reached, the heat pump will stop working but will not stop the circulating pump, so as to ensure a constant circulation of water in your heat pump.

Mode 1 (special mode: factory setting) : This mode has been designed to maintain ltration in your pool

without using the timetable programmer. When the required temperature is reached, the heat pump will go on standby, then 30 seconds later the circulating pump will shut down. The circulating pump will then be reactivated in special mode: 2 minutes operation, 15 minutes shut down (Setting 11 = 15 by default, adjustable

from 3 to 20 minutes), thus maintaining regular ltering of your pool. With a temperature sensor in the heat

exchanger compartment, this mode allows your heat pump to update your pool’s actual temperature every 15 minutes. We therefore recommend this mode. It is only when the pool temperature goes down by 3°C in

relation to the required temperature that the ltration pump and the heat pump resume their normal operating

mode. (This mode is recommended for a direct connection allowing a delayed start of the circulation pump and the heat pump without going through the timer the circulation pump).

4.13 Forced de-icing function

Long press and 3 secondes to enter forced de-icing.

If you have connected a circulating pump to terminals P1 and P2, it is automatically electrically powered when the heat pump operates.

5.2 Servo-control of circulating pump

5. Operation

5.1 Operation

Conditions of use

For the heat pump to operate normally, the ambient air temperature must be between -5°C and 43°C.

Recommendations prior to start-up

Before activating the heat pump, please:

✔ Check that the unit is rmly secured and stable.

✔ Check that the gauge indicates a pressure greater than 80 psi.

✔ Check that the electrical wiring is properly connected to the terminals.

✔ Check the earthing.

✔ Check that the hydraulic connections are tight and that there is no leakage of water.

✔ Check that the water is circulating correctly in the heat pump and that the ow rate is adequate.

✔ Remove any unnecessary object or tool from around the unit.

Operation

1. Activate the unit’s power supply protection (differential switch and circuit-breaker).

2. Activate the circulating pump if it is not servo-controlled.

3. Check the By-Pass opening and the control valves.

4. Activate the heat pump by pressing once on

5. Adjust the remote control clock.

6. Select the required temperature by using one of the remote control’s mode.

7. The heat pump’s compressor will start up after a few moments.

All you have to do now is wait until the required temperature is reached.

WARNING: Under normal conditions, a suitable heat pump can heat the water in a swimming pool by 1°C to 2°C per day. It is therefore quite normal to not feel any temperature difference in the system when the heat pump is working. A heated pool must be covered to avoid any loss of heat.

5. Operation

5.3 Using the pressure gauge

The gauge is for monitoring the pressure of the refrigerant contained in the heat pump. The values it indicates can vary considerably, depending on the climate, temperature and atmospheric pressure.

When the heat pump is in operation:

The gauge’s needle indicates the refrigerant pressure.

Mean operating range between 250 and 400 PSI, depending on the ambient temperature and atmospheric pressure.

When the heat pump is shut down:

The needle indicates the same value as the ambient temperature (within a few degrees) and the corresponding atmospheric pressure (between 150 and 350 PSI maximum).

If left unused for a long period of time : Check the pressure gauge before starting up the heat pump. It must indicate at least 80 PSI.

If the pressure goes down too much, the heat pump will display an error message and automatically go into ‘safe’ mode.

This means that there has been a leakage of refrigerant and that you must call a qualied technician to

replace it.

5.4 Antifreeze protection

When the heat pump is on standby, the system monitors the ambient temperature and the water temperature in order to activate the antifreeze programme if required.

The antifreeze programme is automatically activated when the ambient temperature or the temperature of the water is less than 2°C and when the heat pump has been shut down for more than 120 minutes.

When the antifreeze programme is running, the heat pump activates its compressor and the circulating pump so as to reheat the water until the water temperature exceeds 2°C.

The heat pump automatically leaves the antifreeze mode when the ambient temperature is greater than or equal to 2°C or when the heat pump is activated by the user.

WARNING: For the antifreeze system to work, the heat pump must be powered and the circulating pump activated. If the circulating pump is servo-controlled by the heat pump, it will be automatically activated.

6. Maintenance and servicing

6.1 Maintenance and servicing

Cleaning

The heat pump’s casing must be cleaned with a damp cloth. The use of detergents or other household products could damage the surface of the casing and affect its properties.

The evaporator at the rear of the heat pump must be carefully cleaned with a vacuum cleaner and soft brush attachment.

Annual maintenance

The following operations must be undertaken by a qualied person at least once a year.

✔ Carry out safety checks.

✔ Check the integrity of the electrical wiring.

✔ Check the earthing connections.

✔ Monitor the state of the pressure gauge and the presence of refrigerant.

WARNING: Before undertaking maintenance work on the unit, ensure that you have disconnected the electrical power supply.

In the winter months when the ambient temperature is lower than 3°C, a shut-down heat pump must be winterised to avoid any frost damage.

Winterising in 4 steps

6.2 Winter storage

Step 1

Disconnect the heat pump from the power supply.

Step 3

Unscrew the drain plug and water pipes in order to drain any water from the heat pump.

Step 2

Open the By-Pass valve. Close the inlet and outlet valves.

Step 4

Screw back the drain plug and pipes or block them with rags so as to prevent any foreign bodies from getting into the circuit. Finally, protect the pump with its winter storage cover.

WARNING

DISCONNECT THE POWER SUPPLY

If a circulating pump is servo-controlled by the heat pump, drain this also.

6. Maintenance and servicing

7. Repairs

In the event of a problem, the heat pump’s screen displays a fault symbol instead of temperature indi-

cations. Please consult the table opposite to nd the possible causes of a fault and the actions to be taken.

Fault code examples:

7.1 Breakdowns and faults

Fault code 03

Fault code 21

Fault code 04

Fault code 32

7. Repairs

7.2 List of faults

Code Fault Possible causes Action

Flow sensor malfunction

Insufcient water in heat exchanger

Check your water circuit operation and the opening of the By-Pass valves

Sensor disconnected or defective Reconnect or replace sensor

Antifreeze protection

Protection activated when the ambient temperature is too low and the unit is on standby

No intervention is necessary

High pressure protection

Insufcient water ow

Check water pump operation and openings of By-Pass inlet/outlet valves

Excess refrigerant gas Readjust the refrigerant volume

Defective 4-way valve Replace the 4-way valve

High pressure switch disconnected or defective Reconnect or replace high pressure switch

Low pressure protection

Insufcient refrigerant gas Readjust the refrigerant volume

Defective 4-way valve Replace valve

Low pressure switch disconnected or defective Reconnect or replace low pressure switch

Connection problem between PCB and wired remote control

Bad connection Check wiring connections between remote control and PCB

Defective wired remote control Replace remote control

Defective PCB Replace PCB

Connection problem between PCB and inverter module

Bad connection Check wiring connections between PCB and inverter module

Defective inverter module Replace inverter module

Defective PCB Replace PCB

Vented air temperature too high Insufcient refrigerant gas Readjust the refrigerant volume

Water intake temperature sensor malfunction Sensor disconnected or defective Reconnect or replace sensor

Outside coil temperature error Sensor disconnected or defective Reconnect or replace sensor

Vented temperature error Sensor disconnected or defective Reconnect or replace sensor

Inverter module protection

Defective inverter module

Power off the heat pump and restart

Replace inverter module

Compressor is defective Replace the compressor

Ambient temperature error Sensor disconnected or defective Reconnect or replace sensor

Water temperature at outlet too low for cooling mode

Insufcient water ow

Check water pump operation and openings of By-Pass inlet/outlet valves

Water outlet error Sensor disconnected or defective Reconnect or replace sensor

Backed temperature error Sensor disconnected or defective Reconnect or replace sensor

Outlet temperature too high for heating mode protection

Insufcient water ow

Check water pump operation and openings of By-Pass inlet/outlet valves

Compressor current protection

The speed of compressor is too high Compressor will be lower the speed auto

Water temperature is too high

Check water pump operation and openings of By-Pass inlet/outlet valves

Ambient temperature is too high, air volume is too little Check the fan is working properly and the air inlet is unobstructed

Inside coil temperature error Sensor disconnected or defective Reconnect or replace sensor

8. Recycling

1 2

Disposing of it at your local

recycling centre

Giving it to a social service organisation for it to be repaired

and put back into circulation.

Returning it to the heat pump

distributor against a new

purchase.

Your heat pump has reached the end of its life and you wish to dispose of it or to replace it. Do not throw it in the rubbish bin.

A heat pump must be disposed of separately with a view to its reuse, recycling or upgrading. It contains substances that are potentially hazardous to the environment but which will be eliminated or neutralised by

recycling.

YOU HAVE THREE SOLUTIONS:

8.1 Recycling the heat pump

Dear Sir/Madam,

Please spend a few minutes lling in the warranty registration card

that you will nd on our website:

http://support.poolex.fr/

We thank you for your trust in our products.

Enjoy your swimming!

9. Warranty

The Poolstar Company guarantees the original owner against defective materials and faults in the manufacture of the Poolex Jetline Premium Inverter heat pump for a period of three (3) years.

The compressor is guaranteed for a period of ve (5) years.

The titanium tube heat exchanger has a lifetime guarantee against chemical corrosion, except for frost damage. The condenser’s other components are guaranteed for three (3) years.

The warranty becomes effective on the date of the rst invoice.

The warranty does not apply in the following cases:

• Malfunction or damage arising from an installation, usage or repair that is not in compliance with the safety instructions.

• Malfunction or damage arising from a chemical agent that is unsuitable for the pool.

• Malfunction or damage arising from conditions that are unsuitable for the equipment’s purposes of use.

• Damage arising from negligence, accident or force majeure.

• Malfunction or damage arising from the use of unauthorised accessories.

Repairs undertaken during the warranty period must be approved prior to being carried out by an authorised technician. The warranty shall be null and void if the repair to the equipment is carried out by a person who is not authorised by the Poolstar company.

The guaranteed parts shall be replaced or repaired at Poolstar’s discretion. Defective parts must be returned to our workshops to be covered during the warranty period. The warranty does not cover labour costs or unauthorised replacements. The return of the defective part is not covered by the warranty.

WARNING:

The contractual warranty cannot be validated with the installer or Poolstar unless your prod-

uct has been registered on our website.

Your details may be treated in accordance with the Data Protection Act of

6 January 1978 and will not be divulged to any third party.

9.1 General warranty conditions

10.1 Wiring diagrams

10. Appendices

Poolex Jetline Premium Inverter 90 / 120 / 150

T3T4T5

Reserved

IN2

IN3

IN4

IN5

Reserved

IN1

12V GND A B

EGND

CN-RAT2

CN-RAT1

Reserved

BLACK（high speed）

BROWN

OUT2

OUT1

OUT3

OUT4

OUT6

OUT5

OUT7

Reactive resistance

Compressor

RED

BLUE

WHITE

RED

BLUE

WHITE

Outlet water temp

Ambient temp

Return gas temp

Cooling coil temp

Exhaust temp

Inlet water temp

Condenser temp

Remote control switch

High Pressure Switch

Low Pressure Switch

RED

YELLOW

Water flow switch

WHITE

RED

Wire controller

GREEN

Power: AC 220-240V/50Hz

To pump

L N

P1 P2

RED

BLACK

Y/G

BLACK

BROWN

220-240V~/50Hz

KM1

BLACK

RED

BLACK

GREEN

BLUE

RED

BLACK

Push-button switch

BLACK

FAN CAPACITOR

ORANGE

RED

WHITE

Y/G

BLUE

BLUE（low speed）

WHITE

BLACK

4-way valve

BLUE

RED

BLACK

Electronic expansion valve

AC-N1

AC-L

E-VAL1

BROWN

10. Appendices

Poolex Jetline Premium Inverter 200

T3T4T5

Reserved

IN2

IN3

IN4

IN5

Reserved

IN1

12V GND A B

EGND

CN-L1

CN-L 2

Reserved

BLACK（high speed）

BROWN

OUT1

OUT3

OUT2

OUT4

OUT5

OUT7

OUT6

OUT8

Reactive resistance

Compressor

RED

BLUE

WHITE

RED

BLUE

WHITE

Outlet water temp

Ambient temp

Return gas temp

Cooling coil temp

Exhaust temp

Inlet water temp

Condenser temp

Remote control switch

High Pressure Switch

Low Pressure Switch

RED

YELLOW

Water flow switch

WHITE

RED

Wire controller

GREEN

Power: AC 220-240V/50Hz

To pump

L N

P1 P2

RED

BLACK

Y/G

BLACK

BROWN

220-240V~/50Hz

KM1

BLACK

RED

BLACK

GREEN

BLUE

RED

BLACK

Push-button switch

BLACK

FAN CAPACITOR

ORANGE

RED

WHITE

Y/G

BLUE

BLUE（low speed）

WHITE

BLACK

4-way valve

BLUE

RED

BLACK

Electronic expansion valve

AC-N1

AC-L

E-VAL2

BROWN

CN6

SILENT EFFICIENCYOZONE FRIENDLY

R410

TOUCH & GO

Poolex is a Poolstar Group trademark www.poolstar.fr

TECHNICAL SUPPORT

www.poolex.fr

Issued June 2018

POOLEX 90, 150, 120, 200 Installation And User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual