Model No.
RP9524/SF5040
~
'!'F?!f.'?.!e:Ef
Instruction
2 in 1 Cambi Nailer/Stapler
Ga.18 Staples(1.25x1
Crown:5.7mm
Length:16mm-40mm(5/8" -1-5/8" )
Ga.18 Brad Nai1(1.25x1
Length:15mm-50mm(5/8" -2" )
f!Ei
Manual
.Omm)
.Omm)
IMPORTANT:
rules, operating instructions before first ues
for future reference.
Upon receipt
of
the product, read and follow all safety
it.
And retain this manual
RP2011
,.:
* Technical Data
Capacity . . . . . . . . . . . . . . . .
Nail length
Staple length
Fastener size
Operation pressure
Air inlet
Dimension
Weight
..................................................................
...............................................................
................................................................
................................................................
......................................................................
...................................................................
........................................................................
...................................................
.........................................................
IO
Op
cs
15-50mm(5/8"-2")
16-40mm (5/8"-l 5/8")
18Gauge (1.25 X
18Gauge(l .25 X l
60-
IOOPSI
( 4-Thar)
l/4''N.P.
T.
55
X 245 X 250mm
1.5kgs
* Important Safety Rules
I.
KEEP
CHILDREN
let them handle the tool.
2. USE SAFETY GLASS AND
in work area should always wear safety glass to prevent the injury from fasteners
and flying debris when loading and unloading this tool. Maybe the noise would harm
your hearing, wear the ear protection to safeguard. (See fig 1.)
3.
NEVER
USE OXYGEN, COMBUSTIBLE
power source or would cause explosion and serious personal injury. (See fig 2.)
4.
DO
NOT
120psi.
5.
DO
NOT
PLACE
operator's unexpected tripping .Make sure all connections are tight
CARRING
6.
yoke mechanism to avoid unintentional firing
7.
KEEP
THE
and keep hands, any body parts away rear area to Safety guard against possible injury.
8. DISCONNECT
prevent a fastener from being fired during connection. (See fig3.)
DO
NOT
9.
or the unintentional firing
KEEP
AWAY.
CONNECT
OVER-LONG
TOOL
ONLY BY
TOOL
POINTED
TOOL
THE
All children should be kept away from the work area.
EAR
PROTECTION:
TOOL
TO
COMPRESSED
AIR
HOSE
THE
HANDLE do not keep the trigger pull on safety
AWAY
FROM
FROM
AIR
SUPPLY
TIRGGER
OR
SAFETY DEPRESSED during loading fasteners
of
a fastener would cause personal injury.
Air tool operators and others
OR
ANY
OTHER
AIR
in working area in case
of
fastener.
YOURSELF
BEFORE
and others at all time
LOADING fasteners to
which pressure exceeds
BOTTLE
of
the
GAS
l.OOmm)
.OOmm)
Don't
as
a
nails
staples
-2-
10.
DISCONNECT
maintenance, alter the accessories
11.
DO
NOT
working on airtight case, and vehicles.
NOT
12. DO
The workpiece would split allowing fastener to fly ftee or ricochet causing personal injury.
13.
DO
NOT
personal injury.
13.
NEVER
the screws and securely tightened.
14.
MAKE
the tool can operate well.
15. ONLY USE PARTS AND
DRIVE
DRIVE
DRIVE
USE A
DAILY
TOOL
FROM
AIR
SUPPLY
or
during non-operation.
FASTENER
FASTENERS
FASTENER ON
TOOL
INSPECTION
ON
SCAFFOLDINGS,LADDERS and on such similarly construction, not
CLOSE
TO
TOP
that is leaking air, had missing or damaged parts or requires repair and make sure all
FOR
FREE
ACCESSORIES
HOSE
and close the compressor before performing
THE
EDGE
OF
THE
WORK
OF
NAILED
MOVEMENT
recommend by manufacturer.
FASTENER, or the fastener can ricochet causing
of
trigger, safety mechanism and spring to insure
PIECE.
* Ope.rating instruction
Description
Model SF5040 drives Ga.18 finish nails from l 5mm
in
40mm length. 2
provide more power
comfmi even during extended use. Features 360-degree exhaust port can be adjusted to any direction. Continue
firing for high efficient working. Narrow nose
work, finish paneling, decorative trims, furniture making and etc.
J magazine ,shoot staples and finish nails without adjustment. Large cast aluminum body
to
easily drive nails
in
to hard wood. Comfort grip rubber handle for improved control and
is
to
50mm length and Ga.18 staples from l 6mm to
idea for door and window trims, exterior trims, and cabinet
Air
supply
I.
Use clean, Dry and Regulated compressed air at 4-7 bar (60-!00psi)
2.
Never exceed maximum and minimum pressure. Too low or too high pressure would cause noise, fast-worn or
misfiring.
3.
When connecting air supply always keep hands and body ftom discharge area
4.
A filter-regulator-lubrication
5.
Keep air filter clean. A ditty filter will reduce the air pressure to the tool causing a reduction in power and
efficiency.
6.
For better performance, install a quick connector in your tool and quick coupler
7. Be sure all connections
is
required and should be located as close to tool as possible.
in
air supply system are sealed
to
prevent air loss.
of
tool.
on
the hose
if
possible.
-3-
Loading fastener and operation
Myl;iMii~(M
Always disconnect the tool from the compressed air before loading. When loading
the tool always point the tool away from yourself and others. Make sure that you are not holding the
tool with trigger depressed while loading the tool.
1.
Insert a strip
2.
Release the latch and pusher, slid the pusher against the nails.
3.
Connect the tool to the air supply. Make sure the air pressure is in the correct range denoted in the Technical
Data.
4.
Then test the driving depth in a sample piece
not far enough, adjust the regulator to provide less air pressure or more air pressure.
5.
Never operate tool unless safety nose is contact with workpiece. Do not operate tool without fasteners or
damage to tool may result.
6.
Never fire fasteners into air because fasteners may injury operator or others and damage to tool may result.
7.
The air tool
work. hold gun body firmly and press safety stand on workpiece where fastener is to be applied. Pull the
trigger to drive fastener into workpiece.
8.
This operating procedure provides rapid-fire fastener driving. Never operate tool unless safety stand
contact with workpiece.
of
fasteners into magazine Keeping it point down.
of
wood before using.
is
equipped with safety stand mechanism that disable tool unless safety stand is pushed against
If
the fasteners are being driven too far or
is
* Maintenance
in
@M:iMii~MDisconnect
the tool from the air compressor before adjusting, clearing jams,
servicing, relocating and during non operation.
• Regular lubrication,
tool oil into the air inlet before each work day or after 2 hours
workpiece or type
• Check and change all worn or damaged a-rings, seals, etc. Tight all the screws and caps in case personal
injury.
of
• Inspect trigger and safety mechanism
if
your tool without using the in-liner autoniatic oilier, place 2 or 6 drops
of
continuous use depending on the characteristic
fasteners.
to
assure safe system
is
complete and functional: no
loose and missing parts, no building or sticking parts.
• Keep magazine and nose
of
tool clean and free
of
any dirt lint or abrasive particles.
-4-
of
pneumatic
of
-
* Troubleshooting
The following form lists the common operating system with problem and solutions. Please read the form
carefully and follow
qyl1iQaiaM1f
immediately, or serious personal injury could
perform repairs or replacement
Disconnect tool from air supply before attempting repair or adjustment When replacing
lubricate with air tool oil before assembly.
it
any
of
the following symptoms appears during your operating, stop using the tool
result
Only a qualified persons or an authorized service center can
of
tool.
0-rings or Cylinder,
SYMPTOM
Air leak near top
in trigger area 2.Trigger valve head are damage. 2.Check and replace.
Air leak near bottom
Air leak between body
cylinder cap.
Blade driving
deep.
Tool does not operate well: L Inadequate air supply.
can not drive
operate sluggishly.
Tool skips fasteners.
Tool jams.
of
tool or LO-ring in trigger valve are damage.
3.Trigger valve stem ,seal or
damaged.
of
tool. L Loose screws.
2.
and
L Loose screws.
2.
fastener too
fastener
1.
2.
or
2.
3. Worn or damaged
4.Exhaust
blocked.
1.
Worn bumper or damaged spring.
2.Dirt in front plate. 2.Clean drive channel on front plate.
.Dirt or damage prevents fasteners from 3 .Magazine needs
3
4.Worn or dry
5.Cylinder cover seal leaking. 5.Replace
l
.lnconect or damaged fasteners.
2.Damaged or worn driver guide.
3 .Magazine or nose screw loose. 3.Tighten the magazine.
4.Magazine
PROBLEM
1.
0-ring
are 3.Check and replace trigger valve stem,
seal or
!.Tighten screws.
Worn or damaged
Worn or damaged
Worn bumper.
Air pressure
Inadequate lubrication. 2.Place 2 or 6 drops
moving freely in magazine.
lubrication.
0-rings
or bumper.
0-rings
or seals.
is
too high.
0-rings
or seals.
port in cylinder head is
0-ring
on piston or lack
is
dirty. 4.Clean the magazine.
2.
!.
2.
!.Replace bumper.
2.Adjust the air pressure.
I.Verify adequate air supply.
3.Check and replace
4.Replace damaged internal parts.
l .Repalce bumper or pusher spring.
4.0-ring
of
I.Change and use
2.Check and replace the driver.
SOLUTIONS
Check and replace 0-ring.
0-ring
Check and replace
Tighten screw.
Check and replace
need to be replaced.
And lubricate.
Sealing washer.
conect
0-rings
0-rings
of
oil into air
0-rings
to
be cleaned.
or bumper.
or bumper.
inlet
or seal.
fastener.
-5-
J
@t-'
C"r~
Ci}--~
@Y~
w<d)
i
/j
=-~--'-"''"''
[_,..---
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Compressed Spring
0-ring 31.2 X
0-ring
0-ring
Model
Description No.
Bolt
Deflector Spring
Air
DeOector 23
Bolt
Spring
Cylinder Cover
0-ring
Flat
Switch Valve
Sealing
0-ring
Collar
0-ring
Sealing Washer
Cylinder 38
29.7
Main piston
SF5040
M5x20
Washer 25
IJ.7x2.4
Washer
Washer
24.Sx3.5
2.5
42.6x2.35
30X
1.8
XJ.55
Parts
21
22
24
26 ! Trigger Valve Stem
27
28
29
30
31
32
33
34
35
36
37 Spring 57
39
40
Description
Bumper
Gun
I
I
I
L_
I
I
I
Body
Rubber
Washer 43
Rectangle Washer
Trigger Valve Seat
0-ring
l.7X2
Trigger Valve
0-ring
ll.2X2
Compressed
Step Pin
Trigger
E-ring 02. 5 53
Safoty Spacer 54
Pin
2.5X
Safety stand
Snap Retainer
Tip Stand 59
Pin
Spring
List
Guide
16
-6-
No.
41
42
44
45
46
47
48
49
50
51
52
55
56
58
60
Description
Adj. Nut
Cap 62 Driver
Safety Stand
Slice 64
Bolt
M4x12
Bolt
M4X6
0-ring
2.4 X J
NutM4
Pusher
Pusher
Pipe 70
0-ring
4.5 X 1.2
Compressed Spring
Fixed Lever
Compressed Spring 74
Bolt M4x35
Fixed
Scat
Step Pin
Pipe
Sticker Plate
Indicate Label
No. Description
.8
61
63
65
66
67
68
69 Inlay Slice
71
72
73
75
76
77
78
Movable Magazine
Guide
Spacer
Bolt
M4X
12
BoltM4X
JO
Safety
Cover
Driver Guide
Rubber Handle Case
Cover
Pinl.5Xl2
Fixed Magazine
Supp011
Seat
BoltM4X8
NutM4
Bolt
M4X
16
0-ring 36.3 X 3.55
End
Cap
Air Inlet Plug
The
Famous Name
ZHEJIANG RONGPENG AIR TOOLS CO.,L TD.
p~
In
Tools
WINW.RONGPENG.COM
IN
MADE
Ei
CHINA
Loading...