VERSION
JUNE 2016
FOR MODELS:
22EV125 - EV700
22EV155 - EV900
22EV175 - EV1200
SKIMMER & WATER
FEATURE PUMP
INSTRUCTION MANUAL
888.868.1185
sales@pondmax.com
www.pondmax.com
PMAX US EVOII 700_900_1200 Pump Instructions.indd 1 30/9/16 6:33 am
PONDMAX.COM
WELCOME TO THE WORLD OF PONDMAX™.
YOU MADE THE RIGHT CHOICE INVESTING IN THIS
QUALITY PRODUCT. THANK YOU AND ENJOY.
TECHNICAL SPECIFICATIONS
DESCRIPTION
EV700 EV900 EV1200
MAXIMUM WATER FLOW(GPH)
700 900 1200
MAXIMUM HEAD (FT)
10 14 15.5
POWER CONSUMPTION* (W)
23 32 45
VOLTS (V)
115 115 115
FREQUENCY (HZ) AC
60 60 60
FRONT FILTER CAGE: FLOW ADJUSTER
Yes Yes Yes
FRONT FILTER CAGE: SPONGE PRE-FILTER INC.
Yes Yes Yes
INLET Ø THREAD (INCH)
1 1 1
OUTLET Ø THREAD (INCH)
1 1 1
CABLE LENGTH (FT)
32 32 32
RECOMMENDED TUBING SIZE (INCH) ID
1 1 1
RECOMMENDED FOUNTAIN KIT**
#30 Jet Kit #40 Jet Kit #40 Jet Kit
OTHER MODELS AVAILABLE IN THE EVOII RANGE
EV1800 EV2400 EV3000 EV3600
MAXIMUM WATER FLOW(GPH)
1800 2400 3000 3600
MAXIMUM HEAD (FT)
16 20 21 22
VOLTS (V) & FREQUENCY (HZ) AC
115 / 60 115 / 60 115 / 60 115 / 60
BEFORE USING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY AND
BECOME FAMILIAR WITH THE UNIT. PLEASE KEEP THESE INSTRUCTIONS IN A SAFE
PLACE FOR FUTURE REFERENCE.
* SUBJECT TO VARIATION ACCORDING TO LOAD
** SOLD SEPARATELY
PMAX US EVOII 700_900_1200 Pump Instructions.indd 2 30/9/16 6:33 am
WATERGARDENING TO THE MAXPONDMAX.COM
SKIMMER & WATER
FEATURE PUMPS
DESIGN HIGHLIGHTS
The PondMAX EVOII Skimmer & Water Feature Pumps have been manufactured to provide you with the best quality
pumps for your water feature. Visit our website to view our range of pond filtration, outdoor/underwater lighting, water
treatments and general accessories.
BENEFITS INCLUDE
• SMART MAGTM Motor Protection - Provides longevity by preventing motor burnout.
• Energy Efficient – Exceptionally low power consumption to high-head height / high-volume flow conversion.
• Threaded Inlet & Outlet - Suitable for submersible or external operation and can adapt to different fittings
provided.
• Can Be Installed Vertical or Horizontal - Provides flexibility for installation in many different applications.
• Open Vane Impeller Design – Handles large particles and resists clogging.
• Adjustable Flow Control - Meet the demands of your application and
• PondMax Skimmer & Water Feature pumps are
suitable for use in many different applications
including skimmers, water features, aquatic systems
and hydroponics. Your pump can be used in either
submersible or external applications.
• Skimmer & Water Feature pumps are a magnetically
driven pump, therefore they cannot suck from a water
level that is below the inlet level when used externally.
• Your pump has a single moving part (an impeller)
enabling easy cleaning and maintenance.
• The models EV700 – EV3600 Pumps have SMART
MA
GTM motor protection, which analyses the speed and
torque of the motor.
• SMART MAGTM intelligent circuitry also provides a soft
start for the pump on startup and helps to avoid any
sudden jolting. The intelligent system will change the
motor speed to maximize the flow of water in the
given circumstances.
• Also if the Impeller gets jammed or stops, the circuitry
will sense the state and cut the power automatically
for 3 seconds and then power up again. This
procedure will repeat 3 times. If the rotor is still
jammed, it will activate a prolonged low state, till the
pump is turned off, and adequate maintenance is
carried out. Thus minimizing motor burnout, due to
electrical heat, through lack of water flow through the
motor.
• The motor and electrical components are totally
encapsulated in epoxy resin, ensuring safe operation
under water.
• The pump has a robust bearing and shaft design so no
Oil/grease lubrication is required.
• Skimmer & Water Feature pumps rely on water to
cool and lubricate it. Therefore no harmful oil or
grease lubrication is required.
• PondMAX Skimmer & Water Feature Pumps are
continuous rated therefore are designed to operate
24/7.
• An optional fountain kit can be purchased and fitted
to the models EV700 – EV12
00 pumps. These models
include an optional sponge pre-filter that assists in
straining the partials in the water, to assist the
fountain nozzles becoming blocked up with debris.
See your retailer for options.
PMAX US EVOII 700_900_1200 Pump Instructions.indd 3 30/9/16 6:33 am
PONDMAX.COM
• Any damage to the equipment or unmerited operation
will bring dangers to the surrounding precincts. If there
is any damage of the equipment, it must not to be used.
The equipment should be placed out of reach of
children.
• For your own safety, disconnect from the power supply
before any maintenance. Always unplug the pump from
the power supply when not in use. Never pull the cable
to disconnect the plug from the power supply - grasp
the plug and pull to disconnect. If required, have a
qualified electrician install a weatherproof power supply
point near to the pond or water-feature (within the
cable length of the appliance).
• When used in submerged application, be sure the
equipment is completely in the water. The depth should
not be greater than 6.5Ft.
• Do not operate the pump if the appliance or any
components of the system, such as the power cable,
has been damaged. Check appliance for defects
regularly.
• For safety, plug the pump into an electrical outlet with
a (GCFI) Ground Fault Circuit Interrupter.
• To avoid an electric shock, do not attach the plug to the
power supply socket with wet hands. The drip loop
method should be used to prevent water from traveling
down the cable and onto the plug or power supply.
If the plug does get wet, do not unplug the cable.
Disconnect the circuit breaker that supplies power to
the power supply point. Then unplug and examine the
plug and power supply point for presence of water. If
the power point has become wet, you should consult an
electrician before using the power point again.
• Do not install or store the appliance where it will be
exposed to extreme hot or cold temperatures. Do not
use in water above 95°C.
• Do not cut the cable as this will result in voiding your
warranty.
• Care should be taken to arrange the power cable so
that it cannot be accidentally tripped over or pulled.
• Do not attempt to repair the electrical appliance
yourself. Return to an authorized service center or
place of purchase if a fault occurs, (regular
maintenance is not considered repair and is required by
user).
IMPORTANT SAFEGUARDS
Correct and safe use of the system requires strict compliance with the safety instructions. For
safety reasons, persons less than 16 years of age or persons that are not familiar with these
instructions should not use this equipment.
PRODUCT SPECIFIC SAFEGUARDS
• Do not operate the pump without water in your
plumbing at any time, permanent damage may occur.
• When used in submerged application, be sure the
equipment is completely in the water. The depth
should not be greater than 6.5Ft. If used externally, the
pump must have adequate flooded suction at all times.
• The pump is designed to be used inside skimmers,
directly in a pond or in any other fresh water features.
• The pump should only be used in clean water. Do not
use the pump in, or with, any chemicals such as a
solvent or gasoline.
• The PondMAX Skimmer & Water Feature Pumps are
cooled by water flowing through the inside of the
motor body. If the pump flow becomes restricted it will
overheat and could cause permanent damage. Large
tubing size is strongly recommended to deliver
adequate water flow to cool the pump.
• The pump needs to be cleaned regularly to prevent the
pump becoming blocked, thus causing the pump to
overheat and burn out. This is not a warrantable
event.
It is strongly recommended not to select a pump that is
too small for the job required. The flow rate through the
pump needs to be enough so that a half of the rated
max flow is kept running at all times.
PMAX US EVOII 700_900_1200 Pump Instructions.indd 4 30/9/16 6:33 am
WATERGARDENING TO THE MAXPONDMAX.COM
SKIMMER & WATER
FEATURE PUMPS
7. Fine Daisy
Fountain Nozzle
8. Coarse Daisy
Fountain Nozzle
9. Bell Fountain
Fountain Nozzle
6. Fountain
Nozzle Threaded
Mount
10. Telescopic Riser
with Threaded
Locking Nut
3. Flow
Adjustor
4. 1” Threaded to 1/2”
Threaded Reducing
Adaptor
5. Stepped
Hosetail
2. Dual Control
T-Piece
1. Reducing Nipple
INSTALLATION
For your convenience we have provided two different front filter screen. One has a built in flow control, that can be
used to adjust the water flow if the flow is too fast for a particular installation. It is suggested that this specific front
filter screen be used in clean water features.
The other Front Filter Screen contains a sponge filter insert. This filter is to be connected to the front of the pump to
strain out the larger particles when using a fountain kit. This reduces the frequency of having to cleaning of the
fountain nozzles as often. If using an optional fountain kit, select the filter cage with the sponge insert.
FOUNTAIN KIT SETUP GUIDE
A basic plastic fountain kit is not recommended for pumps that have flow over 1500 GPH. It’s better to use commercial
fountain nozzles for higher flow. See your dealer for examples.
For Pumps, from 250 GPH to 1200 GPH, there are a number of optional fountain kits readily available. PondMAX has
three readily available. For various suggestions of the correct model and fountain type selection see the specification
table on page (page 2).
For the purpose of these guidelines, a PondMAX #30 Jet kit has been selected. The installation principle will be
similar for the other types.
Using the 1” to ½” threaded Reducing Nipple (1), attach onto the Male
Threaded outlet of the pump. Now secure the Dual-Control T Piece
(2)
onto threaded reducing nipple. Now on the top of the Dual-Control T
Piece (2), connect the Threaded Reducing Adaptor (4) on. Now extend
Telescopic Riser with Threaded Locking Nut (10) to the desired height,
then secure onto the top (1” thread) of the Threaded Reducing Adapter
with the threaded locking nut provided. Align Telescopic Riser with
Threaded Locking Nut (10) vertically.
Select the desired nozzle, (7) (8) or (9), and screw into the Fountain
Nozzle Threaded Mount. (6) Then attach the Fountain Nozzle Threaded
Mount to the Telescopic Riser with Threaded Locking Nut (10).
Locate the Stepped Hosetail (5). Attach this to the side outlet of the
Dual-Control T Piece to facilitate an optional accessory, for example; a
small waterfall or spitter. Now, utilizing the two different Flow-Adjuster
knobs (3), on either side of the T-Piece, you can vary the flow to the
fountain head or the optional small waterfall/spitter outlet separately.
Feel free to close off the side outlet of the Dual-Control T Piece, if it is
not required. However if it is required, connect tubing to the Hosetail
provided and direct the hose to your desired location.
Place the pump in desired location; ensure the pump is on a stable
surface that is free of sludge, sand and other debris. Position the device
in the pond horizontally, on a solid base, in such a way that it is fully
covered with water and ensure that the pump is located, at a depth,
in the water, which will not allow it to suck air from the surface. This is
known as cavitation. Cavitation is a cause of premature impeller wear.
The fountain nozzle should now be protruding out of the water. Push the
plug into the power supply outlet to switch on. Use the power supply
switch for turning the unit on and o.
NOTE: PondMAX #30 Jet kit has been selected as a sample.
Fountain kit NOT included with pump. Oered seperately.
PMAX US EVOII 700_900_1200 Pump Instructions.indd 5 30/9/16 6:33 am
PONDMAX.COM
INSTALLATION PLUMBING GUIDE
For your convenience we have provided two dierent plumbing installation scenarios. NOTE If used in submersible
applications, use the Hosetail. If used externally, use the (2) Coupling Fittings provided in the fittings pack.
SUBMERSIBLE USE
When used inside a pond skimmer / water feature
enviroment, follow proceedure as outlined below.
• For best results, use the tubing size recommended in the
Technical Specification table. Depending on the pump
size and your tubing size, select the Hosetail required for
and evaluate which step on the Hosetail will be used. If
you are using 1” hose and you are connecting it to the
3/4”, 1”, 1-1/4”, 1-1/2” Hosetail supplied, remember to saw
off the smaller size connection (I.E.: 3/4” step).
Otherwise it will create a unnecessary restriction in the
plumbing system.
•
Select the 1-1/2” x 1” Reducer Bushing Fitting and thread
onto the outlet of the pump (top). To seal adequately,
the use of thread seal tape may be required (available at
your local dealer).
• The fittings pack includes a red washer designed for
the locking nut on the Hosetail. Place a washer firmly in
the locking nut on the Hosetail fitting. Now thread the
locking nut of the Hosetail onto the 1-1/2” x 1” Reducer
Bushing Fitting on the pump. Fasten firmly but do not
over tighten.
• Now connect the tubing to the Hosetail. Remember to
use Stainless Steel Hose Clamps to fasten the hose on to
the Hosetail barbs. This is to ensure that the pipe does
not blow off at a later time or leak at this point in the
plumbing system.
• Direct the hose to your desired location.
EXTERNAL USE
When installed outside the pond enviroment, follow
proceedure as outlined below.
• •For best results in external applications, the pump must
have adequate flooded suction at all times (installed
outside pond, below elevation of the surface of water).
Also reference the tubing size recommended in the
Technical Specification table to make sure the new or
existing plumbing configuration is sized correctly.
•
In external applications it is necessary to remove the
Front Filter Screen of the pump to expose the threaded
inlet. Do this by removing the Base Plate of pump (see
“Cleaning Instructions” Section) and then turn Front
Filter Screen counterclockwise, t hen pull away from
Pump Motor Body. NOTE: You will not need either of the
Front Filter Screens in an external application, so feel free
to keep with this instruction manual or discard.
• The fittings pack includes (2) 1” x 1” female Coupling
Fittings, which are meant to fit directly onto both the
threaded inlet and outlet on pump.
• Now thread a coupling onto both the inlet and outlet of
the pump. Fasten firmly but do not over tighten. To seal
adequately, the use of thread seal tape may be required
(available at your local dealer).
• Make sure that the suction line (inlet side of plumbing)
has a suction screen or leaf strainer to catch large debris
that could potentially harm pump (ask your local dealer
for further information).
• Now the pump is ready to be connected to new or
existing plumbing configuration. Extra fittings and
adapters may be required (available at your local dealer),
based on the specific application.
CLEANING INSTRUCTIONS
Begin by ensuring that the mains power supply is disconnected before attempting any maintenance of the unit or the
water body. Remove the unit from the water. If your unit is connected to a sponge filter, the front screen and sponge
will clog up over time. Please clean regularly (at least once a month) to ensure strong water flow. Failure to maintain
the unit could result in a burnt out motor and other damage.
• All PondMAX Skimmer & Water Feature Pumps are
water cooled. If pump becomes restricted or blocked,
it may overheat and could cause permanent damage.
• The motor unit of the pump is encapsulated with
epoxy resin and does not need lubrication. Regular
inspections, cleaning and maintenance of impeller is
necessary to ensure longer life. In the center of the
impeller you may notice a small hole opening that
protrudes through the ceramic shaft from front to
back. It is important that this opening is kept
unblocked at all times. This is a cooling channel for the
motor.
• If using a fountain kit, take off the fountain set first by
unscrewing it from the top of the pump. Examine the
nozzles to ensure all ports are unblocked. Clean with a
suitable brush if necessary.
• Maintain the filter sponge regularly according to how
long it takes for the screen to get clogged up. When
the flow starts to be reduced, check and clean if
necessary.
• T
o unclip the front filter screen from the front of
the pump, twist the cage in a counterclockwise
direction and pull forward. See below for diagram.
If available, take out the optional sponge and clean.
. It is recommended that this is done in a bucket of
pond water to ensure the good bacteria present in the
sponge are not killed by the chlorine in tap water.
Check for wear and tear on the sponge and replace if
necessary.
• You can help boost the biological function of your
filter sponge with a bacterial additive, available from
your local dealer.
PMAX US EVOII 700_900_1200 Pump Instructions.indd 6 30/9/16 6:33 am
WATERGARDENING TO THE MAXPONDMAX.COM
SKIMMER & WATER
FEATURE PUMPS
1. Turn the Front Filter Screen in the direction as indicated by the arrow, then pull away from Pump Motor Body.
2. Locate snap-fit release under Base Plate using the arrows above. Using your thumb, apply pressure and unclip Base
Plate until it releases from Pump Motor Body.
3. Remove Base Plate by pulling away from pump motor in the direction of arrow above.
4. T
o remove the impeller of the pump, turn the Impeller Cover Housing in an counterclockwise direction as indicated
by the arrow above, to the stop position. Then separate the Impeller cover from the Pump Motor Body.
5. With one hand gripping the Pump Motor Body, secure grip of other hand tightly on the fins of the Impeller and pull
out the Impeller assembly (take care not to break ceramic shaft.) The black disc behind the fins of Impeller is part
of the Impeller assembly. Clean the Impeller with water and vinegar and a suitable brush taking note to remove fine
sediment on and around the back end of the Impeller, the small hole through the ceramic shaft and the chamber the
Impeller fits into on the Pump Motor Body. (Always inspect the Impeller and replace the Impeller if it seems
necessary.)
6. Ensure to replace the O’ring as shown above when reinstalling the Impeller.
(See “IMPORTANT NOTES” section below for reassembly instructions)
IMPORTANT NOTES
• It is important that this procedure is carried out
regularly as the cooling path inside the motor can
become clogged. If the impeller assembly becomes
worn or damaged it should be replaced (available from
your dealer). Failure to do so may cause serious
damage to pump. Inspect for signs for wear and tear.
The impeller set is a wearable part.
• Once the cleaning and inspection process is
completed, reassemble in the reverses manner.
Reinstall the impeller into the motor body.
To place the Impeller O’ring around the black disc
successfully, firmly hold the disc with one hand, and
using the other hand stretch the O’ring over the disc,
positioning it carefully into the groove. Pay attention
not to allow the O’ring to roll forward, in-between the
black disc and the Pump Motor Body.
With the impeller in the correct position, carefully
place the Impeller Cover Housing on, and then rotate
clockwise back into position.
• If applicable re-insert the internal Sponge back into
the filter screen and re-attach to the pump. On other
models re-attach the Front Filter Screen.
• Now re-attach the Base Plate into position to lock
the impeller cover from turning.
PMAX US EVOII 700_900_1200 Pump Instructions.indd 7 30/9/16 6:33 am
PONDMAX.COM
EXPLODED VIEW
IMPORTANT
These accessories and attachments are recommended for use with your PondMAX product specified in this manual. The use of any other accessories or attachments
might present a risk of injury to persons. Only use the accessory or attachment for its stated purpose.
Front Fiter Screen - for Sponge
Sponge
Flow Control Knob (EV700 - EV1200 Only)
Front Fiter Screen - with Hole For Flow
Control (EV700 - EV1200 Only)
Blanking Cap for Hole in Front Filter Screen
(optional)
1” Coupling Fitting x2 - for Inlet & Outlet
Impeller Cover Housing
Impeller Assembly
Impeller O’ring
Base Plate with Rubber Feet
Pump Motor Body
1” x 1-1/2” Reducer Bushing Fitting
Washer - for Locking Nut (Red)
3/4”, 1”, 1-1/4” & 1-1/2” Barbed Hosetail with
Locking Collar
1
2
3
4
Not
Shown
5
6
7
8
9
10
11
12
13
NOTE: Parts and features dier from model
to model. All images used are for illustrative
purposes only. Not all features depicted
apply to all models in the range and these
are subject to change.
PMAX US EVOII 700_900_1200 Pump Instructions.indd 8 30/9/16 6:33 am
WATERGARDENING TO THE MAXPONDMAX.COM
SKIMMER & WATER
FEATURE PUMPS
SPARE PARTS
PART
NO.
DESCRIPTION
EV700 EV900 EV1200
1
Front Filter Screen - for Sponge
31EV130
2 Sponge
3
Flow Control Knob - [EV700 - EV1200 Only]
31EV127
4
Front Filter Screen - With Hole for Flow Control [EV700 - EV1200 Only]
Not Shown
Blanking Cap for Hole in Front Filter Screen
(optional)
5
1" Coupling Fitting x 2 - for inlet & outlet
31EV126
6
Impeller Cover Housing
31EV125
31EV155
31EV175
7
Impeller Assembly
8
Impeller O'ring
31EV129
9
Base Plate with Rubber Feet
10
Pump Motor Body
11
1” x 1-1/2” Reducer Bushing Fitting
12
Washer - for Locking Nut (Red)
13
3/4”, 1”, 1-1/4” & 1-1/2” Barbed Hosetail
with Locking Nut
5, 11, 12, 13
Complete Kit EV700-EV1200
- Coupling Fitting x2, Reducer Bushing Fittings,
Washer (Red) & Barbed Hosetail with Locking Nut
31EV128
PMAX US EVOII 700_900_1200 Pump Instructions.indd 9 30/9/16 6:33 am
PONDMAX.COM
TROUBLESHOOTING
Problem Reason Solution
WATER PUMP
NOT WORKING
No Power
Check that the plug is connected and
power point turned on.
Filter Screen or Sponge is blocked with
sludge.
Clean the Filter Screen or Sponge.
Impeller is blocked with sludge or lime
scale build up.
Clean the Impeller as per the instructions.
Running without sucient water.
Submerse the equipment underwater
then plug in. Refill if necessary.
Blocked Impeller chamber or
ceramic shaft is broken.
Clean the Impeller. Check for wear.
Replace if necessary.
WATER PUMP
IS NOISY
Blockage in pump. Clear the blockage.
Impeller & Shaft worn out. Replace Impeller Assembly.
Impeller broken. Replace Impeller Assembly.
Water level in feature is too low.
Refill feature with water to appropriate
height.
Unit inlet is blocked or the water pump
outlet is blocked.
Clear all blockages.
The height to which you are pumping is too
high for the given model of pump.
Select a bigger model.
PMAX US EVOII 700_900_1200 Pump Instructions.indd 10 30/9/16 6:33 am
WATERGARDENING TO THE MAXPONDMAX.COM
SKIMMER & WATER
FEATURE PUMPS
LIMITED WARRANTY
• This product is warranted to the initial purchaser to be
free of defects in materials and workmanship at the
time of initial purchase and for a period of 3 years for
PondMAXTM Skimmer & Water Feature Pump Pumps.
Some parts are consumable and may need to be
replaced as part of ongoing product maintenance and
are not covered entirely by this Warranty. The impeller
assembly is a
consumeable part and has a 1-year
warranty. In the event this product malfunctions within
3 years from the date of purchase, the sole obligation
of PondMAXTM International (hereinafter referred to as
PondMAXTM ) will be to repair the unit or replace with
an equivalent new or factory refurbished unit at
PondMAX’s discretion, subject to the following
condition:
• The malfunction is proved attributable to a defect in
materials or workmanship, including repairs performed
under this warranty. Malfunction for any other reasonincluding but not limited to misuse, negligence,
accident, or tampering with parts, incorrect wiring, or
improper installation-will not be remedied under this
warranty.
• PondMAXTM specifically does not guarantee chemical
compatibility, and expressly does not warrant units
from any problems caused by chemical attack or failure
due to incompatibility of fluid being circulated by
pump.
• All warranty repairs must be performed by PondMAXTM
or a PondMAXTM authorized company.
• Purchaser must retain the purchase receipt and present
it with this certificate as proof of ownership and
entitlement to warranty repairs. Unauthorized repairs
will not be compensated by PondMAXTM , and are not
the responsibility of PondMAXTM , and if such repairs
damage the product, such damages are not remedied
under this warranty.
• Purchaser shall bear all shipping, packing and insurance
costs and all other costs, excluding labor and parts
necessary to effectuate repairs under this warranty.
• This warranty is in lieu of all other express warranties
which now or hereafter might otherwise arise with
respect to this product. Any and all limited warranties,
including the warranties of merchantability and fitness
for particular purpose, shall have no greater duration
than the duration period of the express written
warranty applicable to this product, and shall terminate
automatically the expiration of such duration period.
Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not
apply to you. No action shall be brought for breach
of any implied or express warranty after one year
subsequent to the expiration of the duration period of
the express written warranty.
• Incidental and consequential damages caused by
malfunction, defect, or otherwise, and with respect
to breach of any express or implied warranty, are not
the responsibility of PondMAXTM , and, to the extent
permitted by law, are hereby excluded for property
damage, loss of livestock and, to the extent not
unconscionable, for personal injury damage. Some
states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
• This warranty does not apply to any malfunction arising
out of any application of this product other than
normal use, unless such application is upon request
specifically approved in writing by PondMAXTM .
• The provisions of this warranty are severable and if any
provision shall be deemed invalid, the remaining
provisions shall remain in full force and effect.
• Rights under this warranty are not assignable without
the express prior consent in writing by PondMAXTM and,
regardless of the terms of such consent in writing, such
assignee shall have no greater rights than his assignor
had against PondMAXTM .
Please consult your retailer for quality original PondMAX replacement parts. Visit
www.pondmax.com for your nearest dealer.
888.868.1185
sales@pondmax.com
PMAX US EVOII 700_900_1200 Pump Instructions.indd 11 30/9/16 6:33 am
888.868.1185
sales@pondmax.com
PMAX US EVOII 700_900_1200 Pump Instructions.indd 12 30/9/16 6:33 am
Loading...