WK
430 450
Type WE6s32P WK 430 450
dm /min
3
04.2016
04.2016
- 1 -
PPPP
7
aaaa
bbbb
XXXX
XXXX
PPPP
AAAA
BBBB
TTTT
XXXX----XXXX
4WE6 E - 32/G24NZ4 P
5
4
21
3
6
Main elements of directional spool valve type
WE
WEWE
WE
6666
…P
…P…P
…P
are: housing (1), control spool (2), solenoids (3),
centering springs (4), manual overrides (5) and soft-shift
throttle/check valves (6). The spool (2) is shifted when it
is moved into one of end positions by the force of
solenoid (3) affecting it. The return of the spool into
neutral position and centering are secured by the
centering springs (4). The shape of the spool (2) (control
edge spacing) causes change of the hydraulic diagram
performed by the valve. Functions of ports:
P
P P
P - supply port
TTTT - oil return to the tank
AAAA, BBBB - ports for a receiver (a hydraulic cylinder or a
hydraulic motor)
The throttle/check valves (6) allow for setting the speed of
spool (2) position change, independently, at turning on
and turning off the solenoids (3) and in the effect,
eliminating dynamic states (pressure peaks and flow
peaks), causing overload of the receiver and the hydraulic
system, as well as noise generation. In case of power
failure, the shift of the spool (2) can be done manually by
the button (5). The valve can be equipped with a throttling
orifice (7), standard mounted in the P
P P
P port.
NOTE:
NOTE:NOTE:
NOTE:
Prio
PrioPrio
Prior to start of the operation of the valve, it is necessary
r to start of the operation of the valve, it is necessary r to start of the operation of the valve, it is necessary
r to start of the operation of the valve, it is necessary
to thoroughly vent the soft shift valves
to thoroughly vent the soft shift valves to thoroughly vent the soft shift valves
to thoroughly vent the soft shift valves (6666) ports and
ports and ports and
ports and
solenoid chambers
solenoid chambers solenoid chambers
solenoid chambers (5555) ---- see p
see psee p
see page
age age
age 2: requirements
2: requirements 2: requirements
2: requirements for
for for
for
installation and operation
installation and operation installation and operation
installation and operation ---- point 8.
point 8.point 8.
point 8.
NS6
Electrically operated directional spool valve
with a soft-shift function type WE6P
DDDDAAAATTTTAAAA SSSSHHHHEEEEEEEETTTT ---- OOOOPPPPEEEERA
RARA
RATTTTIIIIOOOON
N N
N MA
MAMA
MANUA
NUANUA
NUALLLL
APPLICATION
DESCRIPTION OF OPERATION
Electrically operated directional spool valve type
WE
WEWE
WE
6666
…P
…P…P
…P
is intended for changing the direction of fluid flow in a
hydraulic system allowing change of the direction of
movement of the receiver – usually a piston rod of a
cylinder or a hydraulic motor and also performance of
states:
start, stop
. It can be used to eliminate arising
when overriding adverse dynamic phenomena as a less
expensive alternative to proportionally controlled
directional control valve with electronic controller. It is
adjusted for subplate mounting in any position.
Directional spool valve is complied with the regulations of
directive 2006/95/WE
2006/95/WE2006/95/WE
2006/95/WE for the following voltages:
•50
50 50
50 –––– 250 V
250 V 250 V
250 V for AC
AC AC
AC
•75
75 75
75 –––– 250 V
250 V 250 V
250 V for DC
DCDC
DC
up to 35 MPa
up to 80
Type WE6s32P
WK 430 450 04.2016 - 2 -
DDDDCCCC AAAACCCC
(plug-in connector with rectifier)
222233330000V
V V
V -
- -
- 55550000HHHHz
z z
z 222222220000V
V V
V -
- -
- 55550000HHHHz
z z
z 111111110000V
V V
V -
- -
- 55550000HHHHzzzz11112222V
V V
V 22224444V
V V
V 111111110000VVVV
Weight
with 2 solenoids 2,1 kg
with 1 solenoid 1,5 kg
15000 on/h
33335
5 5
5 MMMMPPPPaaaa
22221
1 1
1 MMMMPPPPaaaa
Viscosity range
Ambient temperature range
mineral oil
Hydraulic fluid
Nominal fluid viscosity
2
o
37 mm /s at temperature 55 C
2
2,8 up to 380 mm /s
recommended
max
Fluid temperature range (in a tank)
40 C up to 55 C
o
o
-20 C up to +70 C
o
o
- 20 C up to +50 C
Re
ReRe
Reqqqquuuuired f
ired fired f
ired flllluuuuid c
id cid c
id cle
lele
leaaaannnnlllliiiine
nene
ness c
ss css c
ss cllllaaaass
ssss
ss
IIIISSSSO
O O
O 4444444400006 c
6 c6 c
6 cllllaaaass
ss ss
ss 22220000////11118888////11115555
port
port port
port TTTT
port
portport
ports P
s Ps P
s P,AAAA, B
B B
B
MMMMaaaaxxxxim
imim
imum
um um
um oper
operoper
operat
atat
atiiiing pres
ng presng pres
ng presssssure
ureure
ure
o o
SSSSupp
uppupp
upply
ly ly
ly vvvvoooolt
ltlt
ltage
age age
age oooof s
f sf s
f soooole
lele
lennnnooooid
idid
idssss
Degree of pr
Degree of prDegree of pr
Degree of pr ooootecti
tectitecti
tectioooonnnn IIIIP
P P
P 66665555
Switching time
Maximum switching frequency
Supply voltage tolerance ±10%
Power requirement (DC) 30 W
Solenoid coil temperature max 150 C
o
ON longer or equal 60 ms
OFF
longer or equal
40 ms
TECHNICAL DATA
INSTALLATION AND OPERATION REQUIREMENTS
1.
1.1.
1. Only fully functional and operational valve, properly
Only fully functional and operational valve, properly Only fully functional and operational valve, properly
Only fully functional and operational valve, properly
connected to electrical installation must be used.
connected to electrical installation must be used.connected to electrical installation must be used.
connected to electrical installation must be used.
Connecting or disconnecting the valve to an electrical
Connecting or disconnecting the valve to an electrical Connecting or disconnecting the valve to an electrical
Connecting or disconnecting the valve to an electrical
installation must only be carried out by qualified
installation must only be carried out by qualified installation must only be carried out by qualified
installation must only be carried out by qualified
personnel.
personnel.personnel.
personnel.
2.
2.2.
2. Ground connection
Ground connection Ground connection
Ground connection ( ) must be connected with
must be connected with must be connected with
must be connected with
protective earth wire
protective earth wire protective earth wire
protective earth wire (PE
PEPE
PE )
in supply system
in supply system in supply system
in supply system
according to appropriate instructions.
according to appropriate instructions.according to appropriate instructions.
according to appropriate instructions.
3.
3.3.
3. Solenoid plug shall precisely adhere to socket and shall
Solenoid plug shall precisely adhere to socket and shall Solenoid plug shall precisely adhere to socket and shall
Solenoid plug shall precisely adhere to socket and shall
be secured with thread bolt screwed in securely in a
be secured with thread bolt screwed in securely in a be secured with thread bolt screwed in securely in a
be secured with thread bolt screwed in securely in a
place.
place. place.
place. It is forbidden to operate
It is forbidden to operateIt is forbidden to operate
It is forbidden to operate the valve if the
the valve if the the valve if the
the valve if the
tightness and suitable clamp of cable in the plug gland
tightness and suitable clamp of cable in the plug gland tightness and suitable clamp of cable in the plug gland
tightness and suitable clamp of cable in the plug gland
are not ensured.
are not ensured.are not ensured.
are not ensured.
4.
4.4.
4. During the period of operation must be kept fluid
During the period of operation must be kept fluid During the period of operation must be kept fluid
During the period of operation must be kept fluid
viscosity acc. to requirements defined in this
viscosity acc. to requirements defined in this viscosity acc. to requirements defined in this
viscosity acc. to requirements defined in this Data
Data Data
Data
Sheet
Sheet Sheet
Sheet ---- Operation
Operation Operation
Operation Manual
ManualManual
Manual
5.
5.5.
5. In order to ensure failure free and
In order to ensure failure free and In order to ensure failure free and
In order to ensure failure free and safe operation the
safe operation the safe operation the
safe operation the
following must be checked:
following must be checked:following must be checked:
following must be checked:
•
• •
• condition of the electrical connection
condition of the electrical connectioncondition of the electrical connection
condition of the electrical connection
•
• •
• proper working of the valve
proper working of the valveproper working of the valve
proper working of the valve
•
• •
• cleanliness of the hydraulic fluid
cleanliness of the hydraulic fluidcleanliness of the hydraulic fluid
cleanliness of the hydraulic fluid
6.
6.6.
6.
Due to heating of electromagnet solenoid coils to
Due to heating of electromagnet solenoid coils to Due to heating of electromagnet solenoid coils to
Due to heating of electromagnet solenoid coils to
high temp., the valve
high temp., the valvehigh temp., the valve
high temp., the valve shall be pla
shall be plashall be pla
shall be pla
ced in such way to
ced in such way to ced in such way to
ced in such way to
eliminate the risk of accidental contact with solenoid
eliminate the risk of accidental contact with solenoideliminate the risk of accidental contact with solenoid
eliminate the risk of accidental contact with solenoid
or valve housing
or valve housingor valve housing
or valve housing
during operation or to apply suitable
during operation or to apply suitable during operation or to apply suitable
during operation or to apply suitable
covers acc. to PN
covers acc. to PNcovers acc. to PN
covers acc. to PN ---- EN ISO 13732
EN ISO 13732EN ISO 13732
EN ISO 13732 ---- 1 and PN
1 and PN1 and PN
1 and PN ---- EN
EN EN
EN 4413
44134413
4413
7.
7.7.
7.
In order to ensure tightness of the directional valve
In order to ensure tightness of the directional valve In order to ensure tightness of the directional valve
In order to ensure tightness of the directional valve
block
blockblock
block,
one should take care of dimension of sealing
one should take care of dimension of sealing one should take care of dimension of sealing
one should take care of dimension of sealing
rings
ringsrings
rings, tightening torques
, tightening torques , tightening torques
, tightening torques
and valve operation
and valve operation and valve operation
and valve operation
parameters given in this Data Sheet
parameters given in this Data Sheet parameters given in this Data Sheet
parameters given in this Data Sheet ---Operation
OperationOperation
Operation Manual
ManualManual
Manual
8.
8.8.
8.
Prior to first use of the valve, one should vent the soft
Prior to first use of the valve, one should vent the soft Prior to first use of the valve, one should vent the soft
Prior to first use of the valve, one should vent the soft
shift valves. It is recommended to set the valve in
shift valves. It is recommended to set the valve inshift valves. It is recommended to set the valve in
shift valves. It is recommended to set the valve in
such a way that the valve settings were directed
such a way that the valve settings were directed such a way that the valve settings were directed
such a way that the valve settings were directed
“upwards”. In order to provide a thorough venting, it
“upwards”. In order to provide a thorough venting, it “upwards”. In order to provide a thorough venting, it
“upwards”. In order to provide a thorough venting, it
is recommended to unscrew the soft shift valves,
is recommended to unscrew the soft shift valves, is recommended to unscrew the soft shift valves,
is recommended to unscrew the soft shift valves,
immerse the ports in oil that is used and override the
immerse the ports in oil that is used and override the immerse the ports in oil that is used and override the
immerse the ports in oil that is used and override the
valve without any load. This process should be
valve without any load. This process should be valve without any load. This process should be
valve without any load. This process should be
rrrr
epeated until the ports are full, and then, the valves
epeated until the ports are full, and then, the valves epeated until the ports are full, and then, the valves
epeated until the ports are full, and then, the valves
can be screwed. After venting, set the valves’ setting
can be screwed. After venting, set the valves’ setting can be screwed. After venting, set the valves’ setting
can be screwed. After venting, set the valves’ setting
to achieve optimal operation of the valve.
to achieve optimal operation of the valve.to achieve optimal operation of the valve.
to achieve optimal operation of the valve.
9.
9.9.
9.
A person that operates the valve must be thoroughly
A person that operates the valve must be thoroughly A person that operates the valve must be thoroughly
A person that operates the valve must be thoroughly
familiar with this Data Sheet
familiar with this Data Sheet familiar with this Data Sheet
familiar with this Data Sheet ---- Operation Manual.
Operation Manual.Operation Manual.
Operation Manual.
Type WE6s32P WK 430 450 04.2016- 3 -
P
T
aaaa
aaaa
0000
0000
bbbb
EEEE
HHHH
JJJJ
EEEEAAAA
HA
HAHA
HA
JA
JAJA
JA
EB
EBEB
EB
HB
HBHB
HB
JB
JBJB
JB
P
T
A
B
P
T
A
B
A
B
0000
bbbb
P
T
A B
aaaa
0000
bbbb
aaaa
0000
P
T
A
B
0000
bbbb
P
T
A
B
P T
A
B
a
aaaa
0000
bbbb
b
a
aaaa
0000
0000
bbbb
b
P
T
A B
P
T
A B
WE6.../
............PPPP
WE6...
BBBB/............PPPP
WE6...
AAAA/............PPPP
versions with positions
aaaa,0000
versions with positi
ons
working and
indirect positions
working
positions
working and
indirect positions
working
positions
working and
indirect positions
working
positions
DDDDiiiiagr
agragr
agraaaams
msms
ms ffffor
oror
or sp
sp sp
spooooooools
lsls
ls
DIAGRAMS
DDDDiiiiagr
agragr
agram
amam
ams f
s fs f
s for
or or
or 3333-p
-p-p
-poooossssit
itit
itiiiioooonnnn
direct
directdirect
directiiiioooonnnnaaaal
l l
l sp
spsp
spooooooool
l l
l vvvvaaaallllves
vesves
ves
DDDDiiiiagr
agragr
agram
amam
ams f
s fs f
s for
or or
or 2222-p
-p-p
-poooossssit
itit
itiiiioooonnnn
direct
directdirect
directiiiioooonnnnaaaal
l l
l sp
spsp
spooooooool
l l
l vvvvaaaallllves
vesves
ves
NNNNOOOOTTTTE:
E:E:
E:
Vers
VersVers
Versiiiioooonnnns
s s
s oooof t
f tf t
f the d
he dhe d
he direct
irectirect
irectiiiioooonnnnaaaal
l l
l vvvvaaaallllve type W
ve type Wve type W
ve type W EEEE6...
6...6...
6...P
P P
P wwwwit
itit
ith
h h
h ooootttther sp
her spher sp
her spoooooooolllls t
s ts t
s to be
o be o be
o be agreed
agreed agreed
agreed wwwwit
itit
ith
h h
h tttthe m
he mhe m
he maaaannnnuuuufact
factfact
facturer.
urer.urer.
urer.
Type WE6s32P
WK 430 450 04.2016 - 4 -
0,63
r
0,01/100
11
aaaa
bbbb
23
42
86 15
1593
47
57
10
9
11
PPPP
TTTT
BBBB
AAAA
154
154
32,5
40,5
17
73
218
310,75
O
5,3
4 holes
O
9,4
4 counterbores
8
1
2
5
3
4 12
7
45
6
O
45
72,5
PPPP
TTTT
BBBBAAAA
5,95
16,25
26,55
0,75
10,3
19
27,8
40,5
10
73 (min)
17
M5 depth 10 - 4 holes
O
7,6 (max) - 4 holes (P, T, A, B)
45 (min)
32,5
31,75
vers
versvers
versiiiioooon
n n
n WWWWEEEE6...
6...6...
6...ZZZZ4...
4...4...
4...PPPP
(electrical connection type
IIIISSSSO
O O
O 4444444400000000
)
OVERALL AND CONNECTION DIMENSIONS
1 - Solenoid on side
aaaa
2 - Solenoid on side
bbbb
3 - Plug-in-connector on side
aaaa -
- -
-
type
ISO 4400
ISO 4400ISO 4400
ISO 4400
(DIN 43650 - A)
4 - Plug-in-connector on side
b -
b -b -
b -
type
ISO 4400
ISO 4400ISO 4400
ISO 4400
(DIN 43650 - A)
5 - Plug-in-connector - type
ISO 4400
ISO 4400ISO 4400
ISO 4400
(DIN 43650 - A)
with
rectifier
6 - Manual override
7 - Soft-shift valve - setting with hexagonal socket
S5
S5S5
S5
(instructions for setting on page 2)
8 -
O-ring
O-ringO-ring
O-ring 9,2 x 1,8
9,2 x 1,8 9,2 x 1,8
9,2 x 1,8
- 4 pcs/set (
PPPP,TTTT,AAAA,BBBB
)
9 - Directional spool valve dimension with
2 s
2 s2 s
2 solen
olenolen
olenoids
oidsoids
oids
on side
aaaa, b
b b
b; 3-po
3-po 3-po
3-possssiti
itiiti
ition
onon
on
springs centere
springs centeresprings centere
springs centere dddd
(spool diagrams:
EEEE,HHHH,JJJJ
- according to page 3)
8 - Directional spool valve dimension with
1 s
1 s1 s
1 solen
olenolen
olenoid
oidoid
oid
on side
aaaa;2-pos
2-pos2-pos
2-positi
itiiti
ition
onon
on springs centered
springs centered springs centered
springs centered
(spool diagrams:
EEEEAAAA, HA
HAHA
HA,JA
JAJA
JA
- according to page 3)
9 - Directional spool valve dimension with
1 s
1 s1 s
1 solen
olenolen
olenoid
oidoid
oid
on side
bbbb;2222-pos
-pos-pos
-positi
itiiti
ition
onon
on springs centered
springs centered springs centered
springs centered
(spool diagrams:
EEEEBBBB,HHHHBBBB, JB
JBJB
JB
- according to page 3)
10 - Porting pattern for directional spool valve - configuration
of connection holes in accordance with the standard
ISO
ISO ISO
ISO 4401
4401 4401
4401
- designation
ISO
ISO ISO
ISO 4401
4401 4401
4401-03
0303
03
-02-0-94 (CETOP 03)
fixing screws
M5 x 50
M5 x 50 M5 x 50
M5 x 50 - 10
- 10- 10
- 10.9
.9.9
.9
in accordance with
PPPPNNNN -
- -
-EEEENNNN IIIISSSSOOOO 4444777766662222
- 4 pcs/set; tightening torque
Md = 9
Md = 9 Md = 9
Md = 9 Nm
NmNm
Nm
11 - Subplate surface required
NNNNOOOOTTTTE:
E:E:
E:
versions
WWWWE6
E6E6
E6...P
...P...P
...P
with
ot
ot ot
other elect
her electher elect
her electrical con
rical conrical con
rical con nectors
nectorsnectors
nectors
see page 5
Type WE6s32P WK 430 450 04.2016- 5 -
aaaa
bbbb
PPPP
TTTT
BBBB
AAAA
23
45
47
64,5
42
156
40,5 17
73
156
221
O
45
32,5
310,75
3
4
O
5,3
4 holes
O
9,4
4 counterbores
aaaa
bbbb
23
45
47
71
1
2
O
5,3
4 holes
O
9,4
4 counterbores
42
PPPP
TTTT
BBBB
AAAA
154
310,75
40,5 17
154
218
73
32,5
45
O
74
72,5
vers
versvers
versiiiioooonnnns:
s:s:
s:
WWWWEEEE6666............GGGG11112222............JJJJ............PPPP; ............GGGG22224444............JJJJ............PPPP
(
electrical connection type
AM
AMAM
AMPPPP JJJJun
unun
uniiiior
oror
or TTTTim
imim
imer
erer
er
)
OVERALL AND CONNECTION DIMENSIONS
vers
versvers
versiiiioooonnnnssss
WWWWEEEE6666............GGGG22224444............DDDD............PPPP
(
electrical connection type
DDDDeu
eueu
euttttssssch
chch
ch
)
1, 2 - Solenoid with connector type
AAAAMMMMP
P P
P JJJJuuuunnnniiiior
or or
or TTTTimer
imerimer
imer
ma
mama
male
lele
le 2222-p
-p-p
-poooole
lele
le
(plug-in-connectors not shown in the
drawing must be ordered separately - Data Sheet
W
W W
W K
K K
K 444499999
9 9
9 999966663333
)
3, 4 - Solenoid with connector type
De
DeDe
Deuuuutsc
tsctsc
tschhhh DDDDTTTT00004444 -2222PPPP
(plug-in connectors
De
DeDe
Deuuuutsc
tsctsc
tschhhh DDDDTTTT00006666
-
2222SSSS
type not
shown in the drawing must be ordered separately Data Sheet
WWWWK
K K
K 444499999
9 9
9 999966663333
)
NNNNOOOOTTTTEEEE
:
Description of other elements of the valve drawing;
porting pattern and requirements of surface state of the
subplate - as in version WE6
…………ZZZZ4444…………PPPP
- see page 4
Type WE6s32P
WK 430 450 04.2016 - 6 -
PPPP
→→→→
AAAA
PPPP
→→→→
B
B B BAAAA
→→→→
TTTT BBBB
→→→→
TTTT
EEEE
HHHH
JJJJ
2222 4444 2222 2222
1111
1111
2222
1111
1111
1111
3333 3333
shifted positions
diagrams according
to page 3
spool symbol
spool symbolspool symbol
spool symbol
ppppeeeerformanc
rformancrformanc
rformanc e dia
e diae dia
e diagram numb
gram numbgram numb
gram numbeeeerrrr
flow direction
0,2
0,20,2
0,2
0,4
0,40,4
0,4
0,6
0,60,6
0,6
0,8
0,80,8
0,8
1,0
1,01,0
1,0
1,2
1,21,2
1,2
0000 10
1010
10 20
2020
20 30
3030
30
40
4040
40 50
5050
50
60
6060
60
70
7070
70
∆
∆
p
p
p
p
[MPa]
[MPa]
[MPa]
[MPa]
QQQQ [[[[dm
dmdm
dm /m
/m/m
/min
inin
in]]]]
3333
4
2
13
80
8080
80
11110000
22220000
33330000
33335555
0000
11110000 22220000 33330000 44440000 55550000 66660000 77770000 88880000
3
1
p [MPa]
p [MPa]
p [MPa]
p [MPa]
Q [d
Q [dQ [d
Q [dm /
m /m /
m /min
minmin
min]]]]
3333
2
EEEE
1111
HHHH 3333
2222
JJJJ
sp
spsp
spooooooool
l l
l symbo
symbosymbo
symbollll
perf
perfperf
performance
ormanceormance
ormance
diagram number
diagram numberdiagram number
diagram number
diagrams according
to page 3
PERFORMANCE CURVES
measured at viscosityν = 41 mm /s and temperature t = 50 C
2
o
Fl
FlFl
Floooow res
w resw res
w resiiiist
stst
staaaance c
nce cnce c
nce cur
urur
urves
vesves
ves
Above
operating
limits are related to symmetrical flow
through all ports i.e. if the oil flows from port PPPP to port AAAA,
then the same flow rate is from port BBBB to port TTTT....
Degree of asymmetry affects adversely the parameters.
NNNNOOOOTTTTE:
E:E:
E:
characteristic curves
p-Q
p-Qp-Q
p-Q
for directional spool valve
type
WWWWEEEE6...
6...6...
6...PPPP
for various spool types
Oper
OperOper
Operat
atat
atiiiing
ng ng
ng llllim
imim
imit
itit
itssss
characteristic curves
∆
pppp(QQQQ
) for directional spool valve type
W
W W
WEEEE6...
6...6...
6...PPPP
for various spool types
Type WE6s32P WK 430 450 04.2016- 7 -
HOW TO ORDER
WE
6
Number of service ports
4-way
=
4
Spool symbol
spool diagrams
- according to
page 3
Series number
(30-39) - connection and installation dimensions unchanged = 3X
series 32
=
32
Manual override
solenoids with manual override
=
N
solenoids without manual override = no designation
Nominal size
(NS)
NS6
=
6
Throttle insert
(in port
PPPP
)
without throttle insert
=
no designation
throttle insertφ0,8 = B 08
throttle insertφ 1,0 = B 10
throttle insertφ 1,2 = B 12
throttle insertφ 1,5 = B 15
Control voltage for solenoids
12V DC = G12
24V DC
=
G24
110V DC = G110
110V AC 50Hz (plug-in-connector with rectifier) = W110R
220V AC 50Hz (plug-in-connector with rectifier) = W220R
230V AC 50Hz
(plug-in-connector with rectifier) =
W230R
Soft-shift function
valve with soft shift function
=
P
Sealing
NBR
(for fluids on mineral oil base) =
no designation
FKM (for fluids on phosphate ester base) = V
Further requirements in clear text
(to be agreed with the manufacturer)
*
P
4
Electrical connection
plug-in-connector type ISO 4400
(DIN 43650 - A)
without LED
=
Z4
plug-in-connector type
ISO 4400
with LED = Z4L
withoput
plug-in-connector, with
2-poles male
AAAAMMMMP
P P
P JJJJuuuunnnniiiior
or or
or TTTTimer
imerimer
imer
type connector (exists for ...
GGGG11112222
... and ...
GGGG22224444
... options only) = J
withoput plug-in-connector, with
DDDDeu
eueu
euttttssssch
chch
ch
type connector
(exists for ...
GGGG22224444
... option only)
= D
NNNNOOOOTTTTEEEES:
S:S:
S:
Directional spool valve should be ordered according to the above coding.
TTTThe
he he
he symbo
symbosymbo
symbolllls
s s
s iiiin b
n bn b
n boooold
ld ld
ld are preferred vers
are preferred versare preferred vers
are preferred vers iiiioooonnnns
s s
s iiiin
n n
n sssshhhhort de
ort deort de
ort delllliiiivery t
very tvery t
very time.
ime.ime.
ime.
Coding example: 4WE6 E - 32/G24 N Z4 P
Type WE6s32P
WK 430 450 04.2016
PONAR Wadowice S.A.
ul. Wojska Polskiego 29
34-100 Wadowice
tel. +48 33 488 21 00
fax.+48 33 488 21 03
www.ponar-wadowice.pl
- 8 -
M
PPPP
TTTT
4W
4W 4W
4WEEEE6 E...P
6 E...P6 E...P
6 E...P
m
AAAA
BBBB
Subplates and screws fixing directional valve
MMMM5
5 5
5 x
x x
x 55550
0 0
0 -
- -
- 11110,
0,0,
0,9999
in accordance with
PPPPNNNN -
- -
- EEEENNNN IIIISSSSOOOO 4444777766662222
- 4 pcs/set
must be ordered separately.
Tightening torque
MMMMd =
d = d =
d = 9 Nm
9 Nm9 Nm
9 Nm
EXAMPLE OF APPLICATION
IN HYDRAULIC SYSTEM
SUBPLATES AND FIXING SCREWS
Subplates must be ordered according to catalogue
sheet
WWWWKKKK 444499996666 444488880000
. Subplate symbols:
G 341/01
- threaded connections
G 1/4
G 342/01
- threaded connections
G 3/8
G 502/01
- threaded connections
G 1/2
G 341/02
- threaded connections
M14 x 1,5
G 342/02
- threaded connections
M16 x 1,5
TTTThe
hehe
he ssssub
ubub
ubppppla
lala
latttteeee ssssymb
ymbymb
ymboooollll iiiinnnn bbbboooolllldddd iiiissss tttthe
hehe
he pre
prepre
prefffferred
errederred
erred
vvvvers
ersers
ersiiiioooonnnn aaaavvvvai
aiai
aila
lala
labbbble
lele
le iiiinnnn sssshhhhor
oror
ortttt de
dede
delllliiiivvvvery
ery ery
ery ttttim
imim
imeeee....
Loading...