USER MANUAL
Next
Thank you
For purchasing a POM Gear
Basik Bluetooth in-ear budds.
POM Gear products are developed
to give the user Peace Of Mind. In
today’s hectic world, managing our
on-the-go lifestyle is a challenge of
its own. POM’s Mission is to Create
Products that Provide Simple Solutions. Combining the Latest Technology and Top Quality Gear to exceed
all expectations. We’re sure you’ll
have an enjoyable user experience.
To get the most of your new POM
Gear travel wall charger, please read
the user manual carefully before use.
#STAYCONNECTED
PRECAUTIONS
In order to ensure proper and safe
use of the headset, please read this
user manual in detail and comply
with all regulations. Be aware the following guidelines when using your
POM Gear headset:
Please do not use the
headset in potentially
hazardous situations to
ensure your safety.
Please avoid using headset to listen to music and
to make or receive phone
calls while driving in order to avoid distractions.
1
2
Next
Please keep product and
its accessories out of the
reach of children, in order
to avoid danger associated with the inappropriate use of small pieces
provided.
Please keep water away
from this specific unit.
Should water enter the
headset, please remove
and let dry before using
again. Contact with water
or other liquids may
cause damage to the
sound quality and opera-
tional use of the headset.
3
4
Previous
Please avoid playing
music in headphones at
highest volume for long
periods of time. Doing so
will prevent users from
hearing sounds around
them and this can be
dangerous. Prolonged
use on high volume may
also lead to damage of
the ear canal resulting in
hearing loss and tinnitus.
If you feel the volume of
the headset may be set
too high, please reduce
the volume immediately.
Stop using the headset if
you feel an obvious discomfort, irritation or have
other adverse reactions.
5
Next
6
The headset should
not be stored or use
at temperatures below
-15°C (5°F) or above
55°C (134°F) which may
shorten headset or battery life.
Previous
VOL (+) / NEXT
MICROPHONE
POWER BUTTON
VOL (-) / PREVIOUS
Next
Charger and Battery Information
Before charging, make sure the
headset has been switched off.
Plug micro USB cable into the
charging port of the headset:
plug the other side of the USB
cable into the USB charger.
Charging will start and the red
LED light will remain lit on the
headset.
1.
2.
Charging Port
Previous
3.
A full charge takes approximately
1.5-2 hours. When fully charged
the red LED light will switch off.
Please unplug charging cable
when fully charged to avoid
overcharging.
Warning:
Please use original cable for
charging all Bluetooth headset
devices. Use of alternative charging
cables may cause damage to the
headset. Alternate cables must have
a voltage of 5v, and have electric
current exceed 100Ma (5V/100MA)
to ensure safe charging and optimal
use of device. This headset uses a
non-detachable built-in rechargeable battery. In order to prevent
damage of the headset please do
not attempt to remove the battery.
Next
P
owering On:
Hold down the Power Button until
blue LED light blinks and “Power On”
voice prompt is heard.
P
airing Mode:
Hold down the Power Button until
blue and red LED lights begin to blink
alternatively. Voice prompt will state
“Pairing.”
VOL (+) / NEXT
MICROPHONE
POWER BUTTON
VOL (-) / PREVIOUS
Previous
P
owering Off:
Hold down Power Button until red
LED lights blinks then turns off. Voice
prompt will state “Power off.”
Pairing Headset with your Device:
1. Keep the distance between the
headset and devices within 1 meter
(3.2 feet) when pairing.
2. Turn on the headset and hold
Power Button until blue and red LED
lights blink alternatively. The device
will enter pairing mode and voice
prompt will state “Paring.”
3. Initiate Bluetooth function on your
music device and the “POM Basik”
should appear on your device’s Bluetooth list. Select the headset and the
voice prompt will state “Connected.”
Next
4. Some mobile phones and other
devices request that you input a pin
number to pair. If so please input the
pin number “0000” as password and
the headset will automatically connect with our mobile phone. When
the headset is connected to your
device the blue LED light will begin to
blink slowly.
5. Reconnecting the headset to a
previous device is simple. When the
headset is turned on and switched
into pairing mode it will automatically
reconnect with the device it was previously connected to when it finds the
device is still available. If your headset
still does not pair, please turn off the
headset and your devices Bluetooth
and repeat steps 1-4.
Previous
D
isconnecting the Headset with
your Device:
• To switch off the headset hold down
the Power Button until the red LED
lights shuts off.
• You can also move the headset 20
meter (60ft) away from the device it
is connected to and the Bluetooth
will automatically disconnect but the
headset will not power off.
A
nswer Incoming Call:
When there is an incoming
call press the Power Button once to
answer the call. You can also use your
mobile device to answer a call.
Next
R
eject a Call:
When there is an incoming call,
quickly press the Power Button twice
to reject the call. You can also use
your mobile phone to reject the call.
E
nd a Call:
Press the Power Button once or
use your mobile to hang up your
current call.
R
edialing a Call:
When using the headset to make
calls you can quickly double-click the
Power Button to redial your last call.
P
laying and Pausing Music:
Press Power Button once to Play
or Pause music.
Previous
V
olume Adjustment & Music
Selection:
1. Press the Vol (+) and Vol (-) but-
tons as preferred to adjust music or
call volume.
2. Press and hold the Vol (+) button
to skip to the next track.
3. Press and hold the Vol (-) button
to restart the current track or return
to the previous track.
Next
SPECIFICATIONS
Bluetooth Version: V4.1
Bluetooth Profile:
HSP, HFP, A2DP, AVRCP, CSR
Frequency range:
20HZ-20000HZ
Operating distance:
33FT
Rechargeable Battery:
Lithium-ion 3.7V / 120 mAh
Charging Voltage:
DC4.75-5.25
Talking/music-playing time:
6 hours
Charging time: 2 hours
Previous
CARE AND HANDLING
Your POM Gear device is a precision-engineered instrument. To
ensure its continuous optimal performance, you should look after it as you
would any quality consumer electronic product, and use it in accordance
with the following instructions.
We recommend:
1. Avoid leaving your device in direct
sunlight or any area where temperature may exceed 60 degrees Celsius
or 140 degrees Fahrenheit. Remember that on a hot day the temperature
inside a closed car may be significantly high than the outside air temperature.
Next
2. Do not leave your device in any
area exposed to humidity, dust, soot,
smoke, or steam or other foreign
objects, as this may cause your device
to malfunction.
3. Do not use any household or industrial grade detergents or cleaners
to clean your device. If your device
becomes dirty, in most instances a
wipe with a dry or slightly damp cloth
should be sufficient enough to clean
it without damaging it.
4. Do not leave your device plugged
into a wall or car charger for long periods of time after it is fully charged.
Many negative affects can be the
result of over charging.
Previous
5. Before charging your POM Gear
device, make sure that the AC outlet;
adaptor and cable are not damaged.
If you notice any abnormalities please
seek advice from a qualified professional before using the cables as this
can result in personal injury as well as
damage your device.
6. When traveling internationally, ensure that your POM Gear device voltage suits to the local power supply.
We would recommend a secondary
power source product from our Power2Go line so as to enable on-the-go
charging for any device.
First page
7. Should a technical difficulty develop within your POM Gear device that
inhibits you to use it properly, contact
info@pomgear.com for advice on
how to proceed.
8. Do not disassemble or attempt
to modify it or replace any part of
this unit, or you won’t be able to use
your warranty coverage.
9. Do not attempt to operate unit using any other method than directed.
Previous
Loading...