
Beschreibung
Der optische Testsender OME 100 wird zur Überprüfung des passiven optischen
Netzwerkes (PON) verwendet. Ausgestattet mit FC/PC bzw. SC/PC Adapter und
einer optischen Leistung von -7 dBm ist der Sender sehr flexibel einsetzbar. Es
können die beiden wichtigen Wellenlängen für Singlemode und Multimode-Fasern,
1310 nm und 1550 nm, genutzt werden
Features
- Handliche Abmessungen und einfache Bedienung
- Großes, gut ablesbares und beleuchtetes LCD-Display
- Automatische Abschaltfunktion
- Hohe Stabilität der Ausgangsleistung
- Möglichkeit des Netzbetriebes (Netzteil im Lieferumfang enthalten)
Lieferumfang
- 1 x OME 100 Testsender
- 1 x Aufbewahrungstasche mit Tragegurt
- 1 x Bedienungsanleitung
- 3 x Batterien Typ AA
- 1 x Reinigungsstäbchenset (25 Stück)
- 1 x 230 V Netzteil
Sicherheitsvorschriften
- Nicht in den Laserstrahl schauen!!
- Wird der OME 100 Testsender über das Netzteil betrieben sind die
Batterien zu entfernen
Wartung
- Der optische Anschluss muss regelmäßig gereinigt werden
- Nach Benutzung das Gerät ausschalten und die Staubschutzkappe
aufstecken
- Das Netzteil darf nur in dem spezifizierten Spannungsbereich verwendet
werden

Montage- und Sicherheitshinweise
ACHTUNG!
1) Nach Öffnen des Gehäuses nicht den optischen Wandler öffnen um
Verschmutzung oder Zerkratzen des SC/APC-Steckers zu vermeiden.
2) Der optische Eingangspegel sollte nicht höher als 30 dBm sein, andernfalls wird
das optische Modul beschädigt.
3) Das Gerät muss vor abnormalem Druck geschützt sein.

Batterie- / Netzbetrieb
Bitte beachten:
Es können Batterien oder Akkus (3 x Mignon AA) verwendet werden.
Die Aufladung der Akkus muss in einem externen Ladegerät vorgenommen
werden.
Dauer des Batteriebetrieb ca. 45 Stunden.
Klappe zur
Benutzung als
Tischgerät

Bedienung
Ein / Aus – Taster: Dient zum Ein – bzw. Ausschalten des Gerätes.
Bei ausgeschaltetem Gerät wird durch einfaches Drücken des Tasters das
Gerät eingeschaltet. Ist das Gerät in Betrieb muss der Taster zum
Ausschalten ca. 1 Sekunden gehalten werden,
Die Auto-Off Funktion ist standardmäßig eingeschaltet, zu erkennen an
dem Schriftzug „Auto-off“. Somit schaltet sich das OME100 automatisch
nach ca. 10 Minuten aus. Um dies zu deaktivieren genügt ein Tastendruck
auf .
CW Auswahl der Modulation: Durch betätigen des Taster wird zwischen
den verschiedenen Modulationen umgeschaltet: 270 Hz, 1 kHz, 2 kHz.
λ Auswahl der Wellenlänge: Umschalten der optische Wellenlänge
1310 nm / 1550 nm. Diese ist im Display ablesbar.
Anzeige ob
Netzbetrieb
230 V
Anzeige ob
Auto-off aktiviert

Messverfahren
Überprüfung eines PON (Passiven optischen Netzwerkes)
1. Stecken Sie das gereinigte Ende des optischen Kabels (Beginn des PON)
in die Messbuchse des OME 100. Kerbe des Steckers beachten!
2. Schalten Sie den optischen Sender OME 100 ein, bitte die automatische
Abschaltung beachten und gegebenenfalls deaktivieren (siehe Seite 5).
3. Im Display des OME 100 wird nun die Messwellenlänge angezeigt, für
SAT-ZF Übertragung wird üblicherweise 1310 nm genutzt.
BK-Gemeinschaftsanlagen mit Vor- und Rückweg können mit 1310 nm und
1550 nm überprüft werden.
4. Schließen Sie das OME 200 an das zu überprüfende und gereinigte Ende
des PON. Kerbe des Steckers beachten!
5. Schalten Sie das optische Messgerät ein, bitte die automatische
Abschaltung beachten und gegebenenfalls deaktivieren (siehe Seite 5).
6. Im Display werden die eingestellte Wellenlänge sowie die anliegende
optische Leistung angezeigt. Die Wellenlänge muss mit dem an der Quelle
eingestellten Wert übereinstimmen. SAT-ZF üblicherweise 1310 nm.
7. Die angezeigte Leistung ergibt sich aus der Quellen-Leistung (bei OME 100
-7 dBm) abzüglich der Dämpfung aller angeschlossenen Komponenten
(Kabel, Verteiler, Adapter, usw.).
Typische Dämpfungswerte:
2-fach Verteiler (z.B.: Polytron OSF 200)
3-fach Verteiler (z.B.: Polytron OSF 300)
4-fach Verteiler (z.B.: Polytron OSF 400)
8-fach Verteiler (z.B.: Polytron OSF 800)

Description
The optical test transmitter OME 100 is used to check the passive optical network
(PON). Equipped with FC/PC or SC/PC adapter and an optical output power of
-7 dBm the device is very flexible useable. The both important wavelengths for
monomode and multimode transmission 1310 nm and 1550 nm can be used.
Features
- Convenient size and easy handling
- Large and good readable backlit LC-Display
- Automatic switch off function
- High stability of the output signal
- Mains operation (Power supply included)
Included parts
- 1 x OME 100 test transmitter
- 1 x Bag with shoulder strap
- 1 x Manual
- 3 x Batteries Type AA
- 1 x Cleaning swabs set (25 Stück)
- 1 x 230 V power supply
Safety instructions
- Don’t look in the laser light of OME 100!!
- If the OME 100 device is used with the power supply, the batteries have to
be removed.
Maintenance
- The optical connector has to be cleaned in regular intervals.
- After use, the device should be switched off and the dust cover should be
put on the optical connector.
- It is only allowed to use the power supply in the specified voltage range.

Mounting and safety instructions
ATTENTION!
1) After opening the unit please do not open the optical adapter converter to avoid
pollution and scratching of the SC/APC connector.
2) Input of optical power should not be higher than 3 dBm, otherwise the optical
modules will be damaged.
3) The unit must be protected against abnormal pressure.

Battery / Mains Operation
Please pay attention:
It´s possible to use battery or accu (3 x Mignon AA).
The accu charge process must be done in an external charging device.
Battery operation approx. 45 hours.

Handling
On / Off – Button: Switches the device on or off.
If the device is switched off it can be started by pressing the „on“ button . If the
device is on, this button has to pressed for 1 sec to switch it off.
The auto-off function is regularly on, shown by displaying „Auto-off“. In this
case the measurement device will switched off automatically after 10 minutes.
By pressing the button this function can be switched off .
CW Selection of the modulation: By pressing the button the different modulations
will be set: 270 Hz, 1 kHz, 2 kHz.
λ Switches the possible wavelengths: 1310 nm and 1510 nm. The selected
wavelength is shown in the display.
Display of
mains operation
mode
Charge state of
the battery
Displays if „auto
off“ is activated

Measurement methode
Check a PON (Passive optical networks)
1. Connect the cleaned end of the optical cable (begin PON) to the
measurement socket of OME 100. Pay attention to the notch!
2. Switch the optical transmitter OME 100 on, pay attention to the switch-off
automatic and deactivate this if necessary (page 11).
3. At the display of OME 100 is now the measurement wavelength shown. For
SAT-IF transmission is regularly used 1310 nm. CATV-systems with
forward- and return path can be measured with 1310 nm and 1550 nm.
4. Connect the OME 200 to the cleaned end of the PON you want to measure.
Pay attention to the notch!
5. Switch the optical measuremrent device on, pay attention to the switch-off
automatic and deactivate this if necessary (page 11)
6. At the display is the selected wavelength and the incoming optical power
shown. The wavelength has to match with the selected value of the source.
SAT-IF normally 1310 nm.
7. The displayed level is the result of the source level (at OME 100 -7 dBm)
minus the attenuation of all connected components (cables, splitter,
adapter, etc.).
Typical attenuation values:
2-way splitter (e.g.: Polytron OSF 200)
3- way splitter (e.g.: Polytron OSF 300)
4- way splitter (e.g.: Polytron OSF 400)
8- way splitter (e.g.: Polytron OSF 800)

Technische Daten / Technical data:
Polytron-Vertrieb GmbH
Postfach 10 02 33
75313 Bad Wildbad
Zentrale/Bestellannahme
H.Q. Order department + 49 (0) 70 81 / 1702 - 0
Technische Hotline
Technical hotline + 49 (0) 70 81 / 1702 - 0
Telefax + 49 (0) 70 81 / 1702 - 50
Internet http://www.polytron.de
eMail info@polytron.de
Technische Änderungen vorbehalten
Subject to change without prior notice
Copyright © Polytron-Vertrieb GmbH
Artikelnummer
Article number
Ausgangsleistung
Output power
CW / 270 Hz, 1 kHz, 2 kHz
Spannungsversorgung
Power supply
3 x 1,5 V AA, 9 V power supply
Betriebstemperatur
Operating temperature
Abmessungen (B x H x T)
Housing (W x H x D)