Polypipe Touch Screen Programmable Room Thermostat Installation & User Manual

Touch Screen Programmable Room Thermostat

Installation and User Manual

PRTIUM1 NOVEMBER 2009

EFFECTIVE: 1ST NOVEMBER 2009

1

Safety Instruction

Installation and mounting of electrical appliances must be
carried out only by skilled electricians. It is imperative to observe
the generally applicable safety measures, such as:

Before starting work on the appliance, switch off power supply
and secure against switching on.

Positioning

The room thermostat should be positioned away from direct
sunlight or heat producing appliances. It is recommended that
the thermostat is installed 1·2 metres above floor level.

Installation

Step 1:

Open front and rear case with screwdriver, then take off
the front case

Step 2:

Open relay case with screwdriver and take off the relay case

Step 3:

Connect all wires properly (See page 2)

Step 4:

Cover the relay case and screw it properly with screwdriver

Step 5:

Mount and fix rear case with screws in wall

Step 6:

Put 2 x 1·5v AA batteries into battery box observing polarity

Step 7:

Cover front and rear case correctly

COM

NC

NO

2

NO

COM

NC

NO

COM

NC

Wiring details for single zone master unit (PB1ZM)

Wiring details for 4 zone and 6 zone slave (PB4ZS and PB6ZS)

3

4

Time Setting

a) Press the key to flash the following in order:

Year, Month, Day, Hour, Minute.

Use the + or – key to adjust each
b) Press OK when complete to confirm exit
Note: The internal calendar will calculate the correct day of the
week (1=Monday etc.)
Note: The time with change automatically to adjust BST and
GMT on the correct date.

Temperature Setting

There are 3 temperature settings available:
Comfort used when room is permanently occupied e.g. 21°C
Economy used when room is temporarily occupied e.g. 18°C
Night used when the room is unoccupied e.g. 15°C
a) Press the key to flash the following in order:

Comfort, Economy, Night. Use the + or – key to adjust each
b) Press OK when complete to confirm exit.

Mode Setting

a) Press the key to select the following:
Automatic (programme mode). The display will also show the
current temperature at that time e.g. or
Continuous operating at comfort temperature
Continuous operating at economy temperature
Continuous operating at night temperature
Continuous operating at frost protection setting (+7°C)

Quick Set Up

To enable quick set up of the Thermostat, there is a pre­installed programme. Simply enter the year, date and time.
Then switch to Auto.
The programme for each day will be as follows:

6.00 a.m. - 8.00 a.m. Comfort setting Set at 21°C

8.00 a.m. - 6.00 p.m. Economy setting Set at 18°C

6.00 p.m. - 11.00 a.m. Comfort setting Set at 21°C

11.00 a.m. - 8.00 a.m. Night setting Set at 15°C
To change any of the temperatures for these times see
Temperature Setting Instructions. To enter different heating
times for each day proceed to Programme Setting Instructions.

Programme Setting

There are three different kinds of programme during the
automatic mode. That is: Daily programme (different
programme for each day of a week), 5/2 programme (the
same programme for Monday (1) - Friday (2) and the same
programme for Saturday (6) - Sunday (7)), Weekly programme
(the same programme for each day of a week).

Daily Programme

a) Press and hold key for 3 seconds to flash the day (1-7)
b) Press + or – key to set the day which you want to programme
c) After setting the day/days, press key to flash time 0:00

and the corresponding bar dot for programme is flashing

d) Press key to enter into energy saving mode; press key to

enter into comfort (sun) mode; press key to enter into night
(moon) mode

e) Press + or – key to adjust time. Repeat step d) and e) if you

want to change the programmed level temperature

f) When you finish setting one day programme,

press to flash day

g) Set the rest days’ programme of a week as above operation

from step b) to step f), after finishing all settings, press OK to
confirm and exit, or exit automatically in 1 minute (after 15
seconds the display will switch off).

5/2 Programme

a) Press and hold key for 3 seconds to flash date
b) Press + or – key to select days from 1 to 5 (these days are

flashing)

c) Set the programme for Monday-Friday and Saturday-Sunday

by using the same way as Daily Programme A operation

Weekly Programme

a) Press and hold key for 3 seconds to flash date
b) Press the + or – key to select days from 1 to 5 (these days

are flashing)

c) Set the programme by using the same method as Daily

Programme operation.

Copy Function

a) Press and hold key for 3 seconds to flash day and enter into

COPY mode when you are in automatic mode The day
and COPY are flashing

b) Press the + or – key to choose the programme of target day

which you want to copy from

c) Press the key again to stop flashing COPY (the programme

is memorised

d) Press + or – key to choose the day which you want to copy

the programme to
e) Press the key again, the programme has been downloaded
f) In the same way to copy and download programme to the

rest days, after finishing all programmes, press OK to confirm

and exit, or exit automatically in 1 minute (after 15 seconds

the display will switch off).

5

Manual Override
Function

During the automatic mode you can have the
override function
Temporary override (Party)
a) Press + or – key to adjust override temperature: the symbol

indicator will appear on the display

b) After setting the temperature, press OK key to confirm and

exit, or exit automatically in 1 minute (after 15 seconds the
display will switch off). The manual setting temperature and
will be kept until entering next setting programme or

when pressing OK key
Hold hours
a) Press + or – key to adjust override temperature: the symbol

indicator will appear on the display
b) Press key once to display 1H and indicator
c) Press + or – key to set holding time from 1 hour to 24 hours
d) Press OK key to confirm and exit, or exit automatically in

1 minute (after 15 seconds the display will switch off).

The number of hours and the override temperature are

flashing alternately on the top right side of the display.

Press OK to exit from the override function.

Hold Days (Holiday)

a) Press + or – key to adjust override temperature: the symbol

indicator will appear on the display
b) Press key twice to display 1d and indicator
c) Press OK key to confirm and exit, or exit automatically

in 1 minute (after 15 seconds the display will switch off).

The number of hours and the override temperature are

flashing alternatively on the top right side of the display.

Press OK for exit from the override function.

Hold Long Period Running

a) Press + or – key to adjust override temperature: the symbol

indicator will appear on the display
b) Press key three times and will display
c) Press OK key to confirm and exit, or exit automatically

in 1 minute (after 15 seconds the display will switch off).

The temperature will be kept until manually pressing OK key.

Alarm Setting

a) Press and hold key for 3 seconds to display AL
b) Then press key once to display on the top left.

Press + or – key to select the days (1-5, 6-7, 1-7)

c) Press key once to flash hour. Press + or – key to set hours

of alarm clock

d) Press key once again to flash minute. Press + or – key

to set minutes of alarm clock

e) Press OK to confirm. After finishing the setting time, buzzer

ring BI-BI for 30 seconds to the programmed time. Press OK
key to turn off the alarm clock in the midway.

To Cancel Alarm

a) Press and hold key for 3 seconds to display
b) Then press and will disappear, press OK key to confirm

and cancel alarm or exit automatically (after 15 seconds the
display will switch off).

Low Battery Indicator

When low battery occurs the symbol will appear on the
display. Change the batteries in a few minutes and the
programme, temperatures and date setting will remain in
memory, you only need to reset the time clock (hours and
minutes)

Key Lockout Function

Hold OK key for 3 seconds to display OK only, all keys will be
locked out. To unlock the keys, hold the OK key for 3 seconds
to restore the display of the keys. Use this function when for
example you need to clean the display.

6

Technical Data

Dimension H x L x W (mm) 87 x 135 x 32

Operating voltage 2 batteries 1.5v LR6/AA

Temperature control range +5°C / +35°C

Temperature display range +5°C / +37°C

Switching capacity
(changeover contact)
at ohmic loads max 6a 240v 50hz
at inductive loads cos w = 0.6 max 2a 240v 50hz

Switching output Floating

Function modes Heat / Cool

Anti-frost +7°C

Ambient temperature –5°C / +45°C

Programming Daily, Weekly and 5/2

Class of protection II

Index of protection IP20

Displayed temperature update 10s

Reading accuracy +/–1°C at 20°C

Reading resolution +/–0.1°C

Swing 0.2°C

Comply with EMC and LV directives

LVD: EN60730-1, EN60730-2-7, EN 60730-2-9

EMC: EN 55014-1, EN 55014-2, EN 61000-3-2, EN61000-3-3

Subject to technical modifications

Touch Screen Programmable

Room Thermostat

Polypipe Building Products

Broomhouse Lane

Edlington

Doncaster DN12 1ES

Tel: [phone]

Fax: [phone]

www.ufch.com

2410 London Road

Mount Vernon

Glasgow G32 8XZ

Tel: [phone]

Fax: [phone]

Dromore Road

Lurgan, Craigavon

Co. Armagh BT66 7HL

Tel: [phone]

Fax: [phone]

www.polypipe.com