Daily Ice Output : 18-20kg / 24 hours
Ice Sizes Three (3): small, medium, large
Ice Storage Capacity : 1500g
Compressor High efficiency CFC free R134a
Water Reservoir Capacity : 3.2 Litres
Dimensions: W375 x D408 x H400 mm
Unit Weight Net 13.5Kg
Voltage: AC 220-240V/50Hz
Power cord: 3 pins grounded plug. (to reduce risk of elec tric shock)
Function
Instant making ice
3 different ice size
Ice full alarming,deficient water alarming
Crystalline ice bullet warhead
14pcs of ice cube in 10mintues
2
Before/First Use of Your Ice Maker
1.During transportation, the incline angle of the cabinet should not be over 45° .Do not turn the Ice maker
upside down. Problems could occur in the compressor and sealed system.
2.Remove all packing material and please check carefully overall of your ice maker in Good condition.It must
no breakage on the unit and no damage on the cord/plug.
3.The Ice maker should be placed horizontally on a properly leveled surface.To ensure proper ventilation for
your Ice maker allow 150mm of space at the top, the back and on each side. P l ease do not install the Ice
maker near an oven, radiator, or other heat source.
4.Before using the Ice maker for the first time, pl ease wai t 2 hours after positioning it, and keep the front lid
open for at least 2hours
5.You must confirm that the voltage indicated on the ice maker is corresponded with the voltage in your home.
6.Pure water is not allowed to be used on this unit, spring water is recommended.
Control Panel Operation
START:Press to turn unit on. This button is also used to start the ice making cycle.
STOP: Press to turn unit off.
SELECT: Ice size selection (S) small, (M) medium or (L) large. (The selected mode shall stay as selected
unless changed or there is a power failure) The default setting is medi um.
ADD WATER:This light will come on with long noise 'DI'. You will need to add water and press the 'STOP' then
the 'START' button to restart the Ice maker.
ICEFULL:This light will come on with 'DI, DI' when the ice has reached the maximum capacity of the storage
cabinet. Press button 'STOP' then press button 'START' to restart the Ice maker after some of the ice has been
taken away.
Operating Instructions
STEP 1.
Open the lid and fill the water reservoir with water.
Note: Make sure the water level is not over the Ice c ollecting tray.
STEP 2.
Connect to the power.
STEP 3.
Select desired ice cube size by pressing 'SELECT'
Note: Please select the (S) when ambient temperature is below 15°c.When the ambient
temperature is higher than 30° C, Large ice cube sizes are recommended.
STEP 4
Press 'START' button to turn unit on. The ice maker begins to work.
Note: For the first three cycles,the ice may be small and irregular in size.
3
STEP 5
If indicator 'ADD WATER' is in red with noise 'DI',then take out the bask et first,then add water same as step 1.
Note:If no water is pumped up to the water tray o ver two cycles but the water in water tank is enough,then
please open the drain cap,and let several drops water runs out.
STEP 6
If indicator 'ICEFULL' is in red with noise 'DI DI',please take out the ice with the scoop.
Note: When the ice collecting tray is full please remove the i ce immediately, Do not allow
the ice collecting tray to overfill.
Y ou must press 'STOP' then the 'START' button to restart the ice maker after you add water
or take out some of the ice.
STEP 7
Press 'STOP' button to stop the machine.
STEP 8
Remove the drain plug to drain remaining water from the water reservoi r.Screw the drain plug back in place
after the water has been drained.
Caring
1.Clean the inner liner, ice collecting tray, water box, ice shovel and evapor ator frequently. When cleaning,
unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inside and
the outside surface of the Ice maker. Do not spray Ice maker with chemicals or diluted agents such as acids,
gasoline or oil. Rinse thoroughly before starting.
2.Keep ventilation openings in the appliance enc losure, or in the built-in structure, clear of obstruction. Do not
use mechanical devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer.
3.If the machine is reused after a long time , maybe the water pump cannot pump sufficient water due to the air
inside, the ADD WATER water indicator turns on in this case . To correct this press the START button again,
then the machine will work normally.
4. To ensure the cleanliness of the ice cubes, water in the water reservoir should be replaced every 24 hours.
5.If the compressor stops for any reason such as water shortage, too much Ice, power off, etc. .. Do not start
the system right away, wait 3 minutes, and then re-start the Ice maker.
6.Always change with fresh water before starting ice product i on at initial installation or after long shut-off
periods.
Troubleshooting
1. Please note, if a power failure occurs due to disconnection of the power cord, or t he off power button has
been pushed off during an ice making cycle, small ice c hips may be formed and may lodge in the automatic
shovel causing it to jam. If this occurs, the ice chips may be removed by disconnecting the power cord and
gently pushing the shovel to the rear of the cabinet and rem oving the ice chips, then restarting.
2. Please restart the ice maker by pressing the button STOP and then St art. If the Ice shovel does not push the
Ice into the Ice collector after the formed Ice dropped from the evaporato r finger and at the same time the M
light is twinkling, then check to see if the water tray is horizontal or balanced , if not then adjust by pressing the
Ice shovel lightly with your finger. Then re-start the Ice maker.
4
Problem
The compressor works
Stop the Ice maker and do not restart
2.Open the drain cap,and let several
The water temperature in
the water storage box or
Refrigerant leaks./ Sealed
The lights of ice full and
then press the ”START” button, two
minutes later the machines will restart
abnormally with a Buzzing
noise
Possible Cause Suggested Solutions
The voltage is lower than
recommended
until the voltage is normal.
Water shortage indicator
light is on
Indicator light on display are
not on
The Ice made is too large
and with pieces sticking
together.
Conditions For Ice making
Cycle are right but no ice is
made.
ADD WATER come on in the
same time.
1.There is no water
2.The pump is full of air
1.Press the stop button, fill with water,
wait 3 minutes and press the start
button to restart. When the water has
reached the fill line the ice maker will
restart automatically.
drops water runs out.
Blown fuse/ No power Replace fuse / Turn power on
Stop the machine and reset the ice
making cycle. Restart the machine
ambient is too low
after turning it off.
call for service
system is
blocked
Water tray is blocked by ice
cube
Clear the ice cube under the ice shovel
to pull out the plug and insert It again
.If the supply cord is damaged; it must be replaced by the m anufacturer, its service agent or a
similarly qualified person in order to avoid a hazard.
. Fill only with potable water.
. It is normal for the compressor and condenser surface to reach temperatures between 70°C and 90°C during
operation and surrounding areas may be very hot.
.Due to fast freezing, ice cubes may appear “Cloudy”. This is trapped air in the water and it will not affect
quality or taste of ice.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities or lack of experience and knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not pl ay with the appliance.
Do not immerse in water
5
automatically
WARNING
Instruction manual.
GUARANTEE FORM
Thank you for choosing our Electric Appliance.
We offer one year conditional guarantee on this product from the date of purc hase.
However, please note this guarantee is valid for normal condition operation o f product. Any damaged of
product due to user mis-use or careless handling, we will not responsible for any guarantee.
Model no.
:
(Lot no. )
Product name :
Date of Purchase :
Place of Purchase :
Note : Please fill details in this form and keep your official purchase receipt together with this
6
Some experts believe the incorrect or prolonged use of almost any
product could cause
serious inju
ry or de
a
th. F
or inf
orm
ation th
at
may reduce your risk of serious injury or deathconsult thepoints
below and additionally, the information available at
www.datastreamserver.com/safety
- Consult all docume ntation, packaging and
product labelling before use. Note that some
products feature online documentation which
should be printed and kept with the p roduct.
- Check product for loose / broken / damaged /
missing parts, wear or leaks (if applicable) before
each use. Never use a product with loose / b roken
/ damaged / missing pa rts, wear or leaks (if
applicable).
- Products must be inspected and serviced (if
applicable) by a qualified specialist every 6
months assuming average residential use by a
person of average weight and strength, ab ove
average technical aptitude, on a property
matching average metropolitan specification.
Intended use outside these guidelines could
indicate the product is not suitable for intended
use or may require more regular inspection or
servicing.
- Ensure all possible users of the p roduct have
completed an industry recognised training course
before being given access to the product.
- The product has been supplied by a general merchandise
retailer that may not be familiar with your specific applic ation or
your description of the applic ation. Be sure to attain third party
approval for your application from a qualified specialist before use
regardless of prior assurances by the retailer or its representatives.
- This product is not intended for use where fail-safe operation is
required. As with any product (take an au tomobile, aircraft,
computer or ball poi nt pen for example) there is always a small
chance of a technical issue that needs to be repaired or may
require replacement of the product or a part. If the possibility of
such failure and the associated time it takes to rectify could in any
situation inconvenience the user, business or employee or could
financially affect the user, business or employee then the product
is not suitable for your requirements. This p roduct is not for use
where incorrect operation or a failure of any kind, including but
not limited to a condition requiring product return, replacement,
service by a technician or replacement of parts could cause a
financial loss, loss of employee time or an in c
onvenience
requiring compensation.
- If this item has been purchased in error considering the points
above simply contact the retailer directly for details of their
returns policies if required.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.