Polycom SpectraLink 8000 SVP100, SpectraLink 8000 SVP020, SpectraLink 8000 SVP010 Administration Manual

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

SpectraLink 8000 SVP Server

SVP100, SVP020, SVP010

Administration Guide

for SIP

November 2009 Edition
1725-36033-001
Version E

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Patent Information

The accompanying product is protected by
one or more US and foreign patents and/or
pending patent applications held by
Polycom, Inc.

Copyright Notice

© 2009, Polycom, Inc. All rights reserved.
POLYCOM®, the Polycom "Triangles" logo
and the names and marks associated with
Polycom's products are trademarks and/or
service marks of Polycom, Inc. and are
registered and/or common law marks in
the United States and various other
countries. All other trademarks are property
of their respective owners. No portion
hereof may be reproduced or transmitted in
any form or by any means, for any purpose
other than the recipient's personal use,
without the express written permission of
Polycom.

All rights reserved under the International
and pan-American copyright Conventions.

No part of this manual, or the software
described herein, may be reproduced or
transmitted in any form or by any means, or
translated into another language or format,
in whole or in part, without the express
written permission of Polycom, Inc.

Do not remove (or allow any third party to
remove) any product identification,
copyright or other notices.

Every effort has been made to ensure that
the information in this document is
accurate. Polycom, Inc. is not responsible
for printing or clerical errors. Information in
this document is subject to change without
notice and does not represent a
commitment on the part of Polycom, Inc.

Notice

Polycom, Inc. has prepared this document
for use by Polycom personnel and
customers. The drawings and specifications
contained herein are the property of
Polycom and shall be neither reproduced in
whole or in part without the prior written
approval of Polycom, nor be implied to
grant any license to make, use, or sell
equipment manufactured in accordance
herewith.

Polycom reserves the right to make changes
in specifications and other information
contained in this document without prior
notice, and the reader should in all cases
consult Polycom to determine whether any
such changes have been made.

NO REPRESENTATION OR OTHER
AFFIRMATION OF FACT CONTAINED IN
THIS DOCUMENT INCLUDING BUT NOT
LIMITED TO STATEMENTS REGARDING
CAPACITY, RESPONSE-TIME
PERFORMANCE, SUITABILITY FOR USE,
OR PERFORMANCE OF PRODUCTS
DESCRIBED HEREIN SHALL BE DEEMED
TO BE A WARRANTY BY POLYCOM FOR
ANY PURPOSE, OR GIVE RISE TO ANY
LIABILITY OF POLYCOM WHATSOEVER.

Contact Information

Please contact your Polycom Authorized
Reseller for assistance.

Polycom, Inc.
4750 Willow Road,
Pleasanton, CA 94588

http://www.polycom.com

2

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

About This Document

This document explains how to configure and maintain one or more
SpectraLink 8000 SVP Servers (models SVP100, SVP020, SVP010)
within IP telephony environments.

Polycom Model Numbers

This document covers the following registered model number:

SVP100

Related Documents

SpectraLink 8020/8030 Wireless Telephone: Administration Guide for SIP

(1725-36038-001)

Available at.

http://www.polycom.com/usa/en/support/voice/w

Polycom VIEW Certified Products Guide (1725-36040-001)

VIEW Configuration Guide 1725-36xxx-001 where xxx indicates a

number corresponding to the type of access point)

Available at

http://www.polycom.com/support/voi

Deploying Enterprise-Grade Wi-Fi Telephony
Best Practices Guide for Deploying SpectraLink 8020/8030 Wireless
Telephones

Available at

http://www.polycom.com/products/voice/wireless_solutions/wifi
_communications/handsets/spectralink_8020_wireless.html

i-fi/wi-fi.html

ce/wi-fi/view_cer

tified.html

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Customer Support

Polycom wants you to have a successful installation. If you have
questions, please contact our Customer Support Hotline at (800) 775-

5330.

The hotline is open Monday through Friday, 6 a.m. to 6 p.m.
Mountain time.

For Technical Support:

For Knowledge Base:

http://www.polycom.com/usa/en/sup

For Return Material Authorization: [e-mail]

Icons and Conventions

This manual uses the following icons and conventions.

Caution! Follow these instructions carefully to avoid danger.

Note these instructions carefully.

Label

This typeface indicates a key, label, or button on Polycom
hardware.

[e-mail]

port/voice/voice.html

4

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Contents

0 About This Document ................................................................3

1 SpectraLink 8000 SVP Server Overview ....................................7

Polycom Model Numbers..................................................................3

Related Documents.............................................................................3

Customer Support...............................................................................4

Icons and Conventions.......................................................................4

SpectraLink Voice Priority (SVP) and Quality of Service ............7

SpectraLink 8000 SVP Server Models ..............................................8

The Timing Function ..........................................................................8

Multiple SVP Servers..........................................................................8

Multiple SVP Server Capacities ......................................................10

Notes on System Configuration......................................................12

System Diagram ................................................................................13

System Components .........................................................................14

The Front Panel of the SVP Server..................................................16

2 Installing the SpectraLink 8000 SVP Server..............................19

Required Materials............................................................................19

Locate the SVP Server.......................................................................20

Install the SVP Server .......................................................................20

3 Configuring the SpectraLink 8000 SVP Server..........................23

Connecting to the SVP Server .........................................................23

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

The NetLink SVP-II System Menu .................................................24

Network Configuration....................................................................25

SendAll .........................................................................................26

SVP Server Configuration................................................................29

QoS Configuration ............................................................................33

Change Password..............................................................................35

4 Swapping/Adding/Deleting SVP Servers.................................37

Adding an SVP Server................................................................37

Removing an SVP Server ...........................................................37

SVP Server Failure ......................................................................38

5 Software Maintenance............................................................39

Software Updates..............................................................................39

6 Troubleshooting via System Status Menu .................................41

Error Status ........................................................................................42

Network Status..................................................................................43

Software Version...............................................................................45

7 Safety Notices ........................................................................47

8 Index .....................................................................................85H49

6

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

SpectraLink 8000 SVP Server
Overview

The SpectraLink 8000 SVP Server is an Ethernet LAN device that
works with access points (APs) to provide QoS on the wireless LAN.
Voice packets to and from the SpectraLink 8000 Wireless Telephones
are intercepted by the SVP Server and encapsulated for prioritization
as they are routed to and from an IP telephony server.

1

SpectraLink Voice Priority (SVP) and
Quality of Service

SpectraLink Voice Priority (SVP) is the SpectraLink quality of service
(QoS) mechanism that is implemented in the wireless telephone and
AP to enhance voice quality over the wireless network. SVP gives
preference to voice packets over data packets on the wireless medium,
increasing the probability that all voice packets are transmitted
efficiently and with minimum delay. SVP is fully compatible with
IEEE 802.11b standards.

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

SpectraLink 8000 SVP Server Models

The SVP Server is available in three models. Which model is selected
for your facility depends on current and expected capacity. All SVP
Servers within a subnet must be the same model type.

• SVP100: Serves 80 calls simultaneously.

• SVP020: Serves 20 powered-on handsets.

• SVP010: Serves 10 powered-on handsets.

See the following capacity tables for multiple SVP Server system
capacities.

All SVP Server models are installed, configured and administered
according to the instructions in this document. The model information
is available on the Software Version screen. See Chapter 6
Troubleshooting via System Status Menu, section Software Version.

The Timing Function

SVP Servers provide the connection or "gateway" to the IP PBX for the
wireless telephones and the "timing" function for active calls. This
"gateway" function is distributed across the SVP Servers.

The number of active SVP Servers is determined dynamically.
Whenever SVP Servers are added to or removed from the system, the
distribution of the "timing" function for active calls is affected.

Multiple SVP Servers

Multiple SVP Server environments are those which have more than
one SVP Server. Up to four SVP010 models or up to two SVP020
models may be installed in any one subnet. Up to 16 models of
SVP100 Servers may be installed in any one subnet. All SVP Servers
must be in the same subnet.

When more than one SVP Servers are installed, the wireless telephone
load is balanced across the available Servers, both for the
communication path between the SVP Server and the wireless

8

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server Overview

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

telephones, and between the SVP Server and the PBX (or other far-end
device).

SVP Server availability

A SpectraLink handset registers to a single SVP Server the first time it
is powered on. Once the handset has contacted this Registration
Server, it obtains a list of all SVP Servers in the system. The handset
then maintains this list in non-volatile memory and updates it only
when rebooted. When a handset later attempts to check in and cannot
contact the ordained Registration Server, it will then fall back to its list
of other Servers and attempt to check in elsewhere. After the handset
has successfully checked into the system once, it never requires that
the Registration Server be present unless the handset is reconfigured
back to factory defaults, or the entire system of SVP Servers is
changed out. See section Swapping/Adding/Deleting SVP Servers.

Registration Server identification

The handsets identify the SVP Server in three possible ways. These
are outlined in the Administration and Configuration document for the
handset model(s) and the IP protocol being used in your facility.
Essentially, the SVP Server can be identified by a static IP address in
the Admin menu, by a DHCP option 151 specification, or by a DNS
query of “SLNKSVP2”. The address found identifies the Registration
Server.

PN: 1725-36033-001_E.doc

9

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Multiple SVP Server Capacities

The system capacity of each SVP Server model is shown in the tables
below. Note that SVP Server models may not be combined within one
subnet.

SpectraLink SVP010 and SVP020 Server capacity

The system capacity of the SVP010 and SVP020 is measured by
number of powered-on handsets. If this number exceeds the
maximum, the handset that cannot be served will display an error
and will not connect to the SVP Server. Other handsets will not be
affected.

Number of handsets Number of SVP

Servers

1 10 20
2 20 40
3 30 N/A
4 40 N/A

SVP010 SVP020

SpectraLink SVP100 Server capacity

The capacity of the SVP100 Server is determined by active calls. The
table below shows the capacity of an IP gateway in a multiple-SVP
Server environment. The table shows the total possible calls at 100%
active calls. However, since it is unlikely that all handsets will be in
use at the same time, the table then analyzes the number of handsets
that could be installed in any given system where 10%, 15% or 20% of
the handsets are in active calls at any one time. The calculations are

1

not linear due to the Erlang

1

An Erlang is a unit of telecommunications traffic measurement. Strictly speaking, an Erlang represents the continuous use of one

voice path. In practice, it is used to describe the total traffic volume of one hour.

Erlang traffic measurements are made in order to help telecommunications network designers understand traffic patterns within
their voice networks. This is essential if they are to successfully design their network topology and establish the necessary trunk
group sizes.

Erlang traffic measurements or estimates can be used to work out how many lines are required between a telephone system and a
central office (PSTN exchange lines), or between multiple network locations.

Please visit www.erlang.com

for additional information.

calculation for telephony traffic. The

10

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server Overview

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

possible installed handsets figures are approximate and meant as a
guideline and not as an absolute recommendation for any facility.

Number

of SVP

Servers

Number

of calls

possible

per Server

Total possible

installed handsets

@ 100% in
active calls

Erlang

Possible installed handsets

@ 10%

in active

calls

@ 15%

in active

calls

@ 20%

in active

calls

1 80 80 65 500 433 325
2 64 128 111 1000 740 555
3 60 180 160 1500 1067 800
4 58 232 211 2000 1407 1055
5 57 285 262 2500 1747 1310
6 56 336 312 3000 2080 1560
7 56 392 367 3500 2447 1835
8 55 440 415 4000 2767 2075

9 55 495 469 4500 3127 2345
10 55 550 524 5000 3493 2620
11 55 605 578 5500 3853 2890
12 54 648 621 6000 4140 3105
13 54 702 674 6500 4493 3370
14 54 756 728 7000 4853 3640
15 54 810 782 7500 5213 3910
16 54 864 836 8000 5573 4180

PN: 1725-36033-001_E.doc

11

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Notes on System Configuration

In an IP system using subnets to differentiate telephony areas, each
subnet must have its own APs. Each subnet may require an SVP
Server to maintain voice quality, but this depends on traffic volume
and router capacity.

Multiple SVP Server environments are those which have more than
one SVP Server.

SVP Server models may not be combined within one subnet. More
than one SVP Server model type may be used within a facility if
installed on different subnets.

Wireless telephones cannot roam with uninterrupted service
between subnets unless specific LAN components are present.
Certain AP/Ethernet switch combinations establish a layer-2 tunnel
across subnets that enables the handsets to roam. Without this
capability, any call in progress will be dropped when the user
moves out of range and the handset must be power cycled in order
to resume functionality in the new subnet area.

Please see Best Practices for Deploying Enterprise-Grade Wi-Fi
Telephony for detailed configuration information when installing
multiple SVP Server models across several different subnets.

IP multicast addresses are used when SpectraLink i640 and 8030
Wireless Telephones are installed. This requires that multicasting
be enabled on the subnet used for the SpectraLink 8000 Wireless
Telephones, SVP Server, and telephony gateways.

Routers are typically configured with filters to prevent multicast
traffic from flowing outside of specific domains. The wireless LAN
can be placed on a separate VLAN or subnet to reduce the effects
of broadcast and multicast traffic from devices in other network
segments.

The SVP Server requires a Cat. 5 cable connection between its
network port and the Ethernet switch. The SVP Server auto­negotiates to the type of port on the Ethernet switch and supports
10Base-T, 100Base-T, full-duplex and half-duplex port types.

12

PN: 1725-36033-001_E.doc

System Diagram

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

The following diagram shows multiple SVP Servers residing on a
network with an IP telephony gateway and IP telephony server,
wireless LAN APs, and Ethernet switch:

Access point

SpectraLink

Wireless Telephones

TFTP server

Ethernet switch

SpectraLink 8000 SVP Server Overview

SpectraLink 8000

SVP Server

SpectraLink 8000

SVP Server

SpectraLink 8000

SVP Server

optional multiple

SVP Servers)

(showing

Optional

Wireless

POS

Access point

IP gateway

PSTN

or

PBX

SpectraLink

Wireless Telephones

SpectraLink 8000

System Components

Ethernet cable
Phone cable

SpectraLink 8000 System Integrated into IP Telephony System

IP phones

PN: 1725-36033-001_E.doc

13

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

System Components

SpectraLink e340/h340/i640 and
8020/8030 Wireless Telephones

Employees can carry wireless telephones to make and receive calls as
they move through the WLAN coverage area. The wireless telephones
are to be used on-premises; they are not cellular or satellite phones.
Just like wired telephones, they can receive calls directly, receive
transferred calls, transfer calls to other extensions, and make outside
and long distance calls (subject to the restrictions applied in your
facility.)

Access points

Supplied by third party vendors, APs provide the connection between
the wired Ethernet LAN and the wireless (802.11) LAN. APs must be
positioned in all areas where wireless telephones will be used. The
number and placement of APs will affect the coverage area and
capacity of the wireless system. Typically, the requirements for use of
SpectraLink 8000 Wireless Telephones are similar to those of wireless
data devices. Contact Polycom, or a certified Polycom distributor, for
specific information about your facility’s needs.

The SpectraLink 8000 System must connect to APs that utilize
SpectraLink Voice Priority (SVP). Contact Polycom, or a certified
Polycom distributor, to verify that your AP and its software version
are supported.

Ethernet switch

A component in the wired Ethernet LAN infrastructure. Switches
interconnect multiple network devices, including APs and other
components. Ethernet switches are required to provide the higher
performance network connections needed to handle combined voice
and data traffic.

14

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server Overview

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Router

A router is an optional component in the wired Ethernet LAN
infrastructure that separates a wired LAN into segments so that
network traffic is restricted to those segments that are directly
involved in the communication. Installation of a network router is
recommended in larger networks, where there may be significant
network traffic not related to the wireless LAN. A router will isolate
the wireless LAN from the associated wired LAN so that they are not
impacted by each others’ traffic. The SVP Servers, the APs, and their
associated Ethernet switch must all be on the same “side” of the
router.

SpectraLink 8000 SVP Server

The SVP Server manages call network traffic as detailed in this
document.

Administrative computer

An administrative computer is required for setup and maintenance of
the SVP Server. This computer may be temporarily connected directly
to the component or to the network; a dedicated computer is not
required. Some installations use a laptop to configure and maintain
system components.

TFTP server

Required in an IP system to distribute software to the wireless
telephones and SVP Server. May be on a different subnet than the IP
gateway, IP telephony server, and APs.

PN: 1725-36033-001_E.doc

15

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

The Front Panel of the SVP Server

The SVP Server’s front panel contains ports to connect to power, the
LAN, and to an administrative computer via an RS-232 port. Status
LEDs supply information about the SVP Server’s functioning.

RS-232

3 4 51 2

L

ACC
N
K
O

O

NETWORK

E
R
R

O

Status

PWR

RS-232 Port: male DB-9 connector (DTE) used for RS-232 connection to

a terminal, terminal emulator, or modem for system administration.

LEDs

LNKOK: Lit when there is a network connection.

ACT: Lit if there is system activity.

COL: Lit if there are network collisions.

NETWORK: Port to wired (Ethernet) LAN.

ERROR: Lit when the system has detected an error.

STATUS: Indicate system error messages and status.

1: Heartbeat, indicates gateway is running.

2: If active calls.

3: SVP Server is locked.

4: Currently unused.

5: This SVP Server is the cluster master.

PWR (power jack): Connects to the AC adapter supplying power to the

system.

Use only the Polycom-provided Class II AC Adapter with output 24V
DC, 1A.

16

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server Overview

7

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Note that the model designation may be found on the label which is
on the side of the SVP Server.

PN: 1725-36033-001_E.doc

1

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Installing the SpectraLink 8000
SVP Server

As shown in the system diagram, the SVP Server is connected to the
Ethernet switch. The specifications covered here allow for great
flexibility in physical placement of the components within stated
guidelines.

See the Configuration and Administration document for your vendor’s
IP system for information on LAN requirements, network
infrastructure and IP addressing.

2

This unit must be installed by a service person familiar with the
installation of electronic equipment.

Do not power up the unit before it has been properly grounded to a
protective earth. See Grounding instructions below.

Required Materials

The following equipment must be provided by the customer.

 Power outlet – AC adapter provided by Polycom.
 Backboard space – the SVP Server is designed to be wall- mounted

to ¾" plywood securely screwed to the wall.

 Screws – required to mount the SVP Server to the wall. Four #8

3/4" panhead wood screws (or similar device) are required.

 Cat. 5 cable – RJ-45 connector at the SVP Server. Connection to

Ethernet switch.

 Grounding materials per section below Grounding Instructions.

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Locate the SVP Server

The SVP Server measures approximately 4 x 12.5 x 7 inches, and
weighs about five pounds. The unit can be wall- mounted, vertically
or horizontally, over ¾" plywood. The SVP Server can also be rack­mounted using a rack- mount kit (sold separately).

Locate the SVP Server in a space with:

• Sufficient backboard mounting space (for wall mount) and

proximity to the LAN access device (switched Ethernet hub) and
power source.

• Easy access to the front panel, which is used for cabling.

• A maximum distance of 325 feet (100 meters) from the Ethernet

switch.

Install the SVP Server

The SVP Server may be mounted on a rack or to a wall.

Mount the SVP Server on a rack

The rack-mount kit is designed for mounting equipment in a standard
19- inch rack and should contain the following equipment:

 Mounting plates – two for each SVP Server to be mounted.
 Screws – four rack-mount screws for each SVP Server to be

mounted.

To rack-mount the SVP Server:

1. Remove the corner screws from the SVP Server.

2. Screw the U-shaped end (round screw holes) of the two mounting

plates to the SVP Server.

3. Screw the other end of the two mounting plates (oblong screw

holes) to the rack.

4. Repeat steps 1-3 for each additional SVP Server. The mounting

plate is designed to provide the correct minimum spacing
between units. When mounting multiple units, stack the units in
the rack as closely as possible.

20

PN: 1725-36033-001_E.doc

Installing the SpectraLink 8000 SVP Server

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Mount the SVP Server to a wall

The SVP Server can be mounted either horizontally or vertically.

To mount the SVP Server to a wall:

1. Using a 1/8-inch drill bit, drill four pilot holes, on 1.84-inch by

12.1-inch centers (approximately equivalent to 1-13/16” by
12-1/8”).

2. Insert the #8 3/4-inch screws in the pilot holes and tighten,

leaving a 1/8-inch to 1/4-inch-gap from the wall.

Grounding instructions



Safety

Warning

The metal chassis of this unit may contain leakage currents (i.e.,
"touch" current) which is cumulative when multiple units are
connected together to form a system. To prevent the summation of
leakage currents from being present on exposed metal surfaces, the
following installation procedure must be followed.

All system units must be grounded to a protective earth by means of
the grounding stud located on the rear panel. Refer to the illustration
below for recommended continuity connection.

No more than 15 units may be grounded through one connection to
the protective earth ground. Systems involving more than 15 units
must be broken up into groups of 15 or fewer units with each group
provided with an independent protective earthing conductor.

PN: 1725-36033-001_E.doc

21

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Connect SVP Server to LAN

Using a Cat. 5 cable, connect the NETWORK port on the SVP Server to
the connecting port on the Ethernet switch.

Connect power

1. Once the units have been properly grounded, connect the power

plug from the AC adapter to the jack labeled
Server.

Use only the provided Class II AC Adapter with output 24V DC, 1A.

2. Plug the AC adapter into an 110V AC outlet to apply power to the

SVP Server.

3. Verify that leakage current ("touch" current) is below 250 μA rms

on exposed metal surfaces.

PWR on the SVP

4. If leakage is excessive, power off the system and re-verify ground

path continuity.

5. The system will cycle through diagnostic testing and the LEDs

will blink for about one minute. When the system is ready for use:

— The ERROR LED should be off.
— Status 1 should be blinking.

22

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

3

Configuring the SpectraLink 8000
SVP Server

During initial setup of the SVP Server the IP address is established
and the maximum number of active calls per AP is set. Optionally,
you may enter a hostname and a location for software updates via
TFTP.

Connecting to the SVP Server

The initial connection to the SVP Server must be made via a serial
connection to establish the SVP Server’s IP address. After the IP
address is established, connection to the SVP Server may be done via
the network using telnet. It is recommended that the basic setup
actions occur while the serial connection is made.

Connect via the serial port

1. Using a DB-9 female, null-modem cable, connect the SVP Server to

the serial port of a terminal or PC.

2. Run a terminal emulation program (such as HyperTerminal™) or

use a VT-100 terminal with the following configuration:

Bits per second: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

3. Press Enter to display the SVP Server login screen.

4. Enter the default login: admin and default password: admin.

These are case sensitive.

5. The

PN: 1725-36033-001_E.doc

NetLink SVP-II System menu will display.

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Connecting via telnet

Telnet can only be used after the SVP Server’s IP address is
configured.

The telnet method of connection is used for routine maintenance of
the SpectraLink Server for both local and remote administration,
depending on your network.

To connect via telnet, run a telnet session to the IP address of the SVP
Server. Once you connect and log in, the
displays.

The NetLink SVP-II System Menu

The main menu displays as shown here:

NetLink SVP-II System menu

System Status

Menu for viewing error messages, status of operation and software
code version.

SVP-II Configuration

Allows you to set the mode and reset the system.

24

PN: 1725-36033-001_E.doc

Network Configuration

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Allows you to set network configuration options, including IP
address and hostname.

Change Password

Allows you to change the password for SVP Server access.

Network Configuration

The IP address and other network settings are established via the

Network Configuration screen. This is also where you may optionally

establish a hostname and enter the IP address of the location of any
software updates you may obtain from Polycom. See Chapter 5
Software Maintenance for more information about installing software
updates via TFTP.

Configuring the SpectraLink 8000 SVP Server

Scroll to
similar to the following appears:

Network Configuration and select by pressing Enter. A screen

Note the navigation options at the bottom of the screen. Press Enter to
change a value, ESC to exit the screen, and the arrow keys to move
the cursor.

PN: 1725-36033-001_E.doc

25

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

SendAll

In an IP system with multiple SVP Servers, the SendAll option is
provided to speed configuration and to ensure identical settings. The

S=SendAll option allows you to send that configuration parameter to

every SVP Server on the LAN.
address is established on EACH SVP Server via the serial connection.
If you anticipate identical settings across the LAN, set just the IP
address and custom hostname (if desired) for each SVP Server using
the initial serial connection. Then connect via the LAN and use
to set identical configuration options for all SVP Servers.

If

SendAll is to be utilized in your system, all passwords must be

identical. DO NOT CHANGE THE PASSWORD AT THE INITIAL
CONFIGURATION IF THE
default password and change it globally if desired after a LAN
connection is established for all SVP Servers.

If independent administration of each SVP Server is desired, the
passwords may be set at initial configuration.

SendAll can only be used after the IP

SendAll

SendAll OPTION IS DESIRED. Use the

The following options must be configured:

IP Address

Enter the IP address of the SVP Server, defined by your network
administrator. Enter the complete address including digits and
periods.

The SVP Server will automatically lock for maintenance if the IP
address is changed. When this
must be reset upon exit. All active calls are terminated during a reset.

DHCP may be entered.

Maintenance Lock occurs, the SVP Server

Hostname

(Optional) change the default host name, if desired. This is the name
of the SVP Server to which you are connected, for identification
purposes only. You cannot enter spaces in this field.

The host names for each SVP Server and OAI Gateway on the
system must be unique.

Subnet Mask

The network administrator must define the subnet mask.

26

PN: 1725-36033-001_E.doc

Configuring the SpectraLink 8000 SVP Server

7

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Default Gateway

The IP address of a router on the local subnet.

SVP-II TFTP Download Master

This entry indicates the source of software updates for the SVP Server.
See Chapter 5 Software Maintenance for more information. Valid source
location entries are:

• NONE: disables.

• IP Address: The IP address of a network TFTP server that will be

used to transfer software updates to the SVP Server.

DNS Server and DNS Domain

These settings are used to configure Domain Name services. Consult
your system administrator for the correct settings. These can also be

DHCP. This will cause the DHCP client in the SVP Server to

set to
attempt to automatically get the correct setting from the DHCP server.
The DHCP setting is only valid when the IP address is also acquired
using DHCP.

WINS Servers

These setting are used for Windows Name Services. Consult your
system administrator for the correct settings. These can also be set to

DHCP. This will cause the DHCP client in the SVP Server to attempt to

automatically get the correct setting from the DHCP server. The
DHCP setting is only valid when the IP address is also acquired using
DHCP.

When the name services are set up correctly, the SVP Server can
translate hostnames to IP addresses. Using telnet, it is also possible
to access the SVP Server using its hostname instead of the IP
address.

Workgroup

As set in WINS.

PN: 1725-36033-001_E.doc

2

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Syslog Server

Logging may be set to either DHCP (see DNS above), an [IP address] or

NONE. If Syslog is set, a message is sent to the syslog server when an

alarm is triggered.

Disable Telnet service

Prevents Telnet access into the SVP Server. Reset the SVP Server for
the change to take effect. Upon reset the Telnet protocol server is not
started.

The SVP Server must be reset in order to set the configuration options.
If the SVP Server is in
selecting the
pressing Y upon exit.

Reset option in the SVP-II Configuration screen and then

Maintenance Lock, you must manually reset it by

28

PN: 1725-36033-001_E.doc

SVP Server Configuration

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

The SVP-II Configuration screen is where you set the mode of the SVP
Server. It is also where you can lock the SVP Server for maintenance
and reset the SVP Server after maintenance. The type of gateway you
are using determines the mode of the SVP Server.

Configuring the SpectraLink 8000 SVP Server

From the main menu, scroll to
pressing Enter.

Ensure the SVP-II Mode is set to NetLink IP as shown in the above screen.

SVP-II Configuration and select by

The following options must be configured:

Phones per Access Point

AP specifications are detailed in the Configuration Notes for each brand
and type. Refer to these notes when entering the number of
simultaneous calls supported for your type.

802.11 Rate

Select 1MB/2MB to limit the transmission rate between the wireless
telephones and APs. Select
to determine its rate.

PN: 1725-36033-001_E.doc

Automatic to allow the wireless telephone

29

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

First Alias IP Address/Last Alias IP Address

The SVP Server uses an IP address when acting as a proxy for the
wireless telephone. Therefore, one alias IP address is required for
every installed Wireless Telephone. These IP addresses must be
entered as a range and must be assigned solely for this purpose.

When multiple SVP100 Servers are installed, a different range must be
configured in each SVP Server. In determining how many addresses
to configure per SVP Server, use this formula: (# of handsets / # of
SVP Servers) + 30%. This formula will accommodate the possibility of
unequal distribution of handsets among the available SVP Servers.

All alias addresses must be on the same subnet as the SVP Server
and cannot be duplicated on other subnets or SVP Servers. There is
no limit to the number of addresses that can be assigned, but the
capacity of each SVP Server is 500 wireless telephones.

Alias IP Addresses are not necessary in Cisco systems.

Enable H.323 Gatekeeper

In certain H.323 protocol systems, the SVP Server may function as a
gatekeeper. Enter Y to have the SVP Server function as the gatekeeper
in the H.323 protocol environment.

Ethernet link

The SVP Server will auto-negotiate unless there is a need to specify a
link speed.

Check-in throttling

The check-in throttling option regulates the number of handsets that
can check-in simultaneously. The error
caused by a massive check-in that has overwhelmed the server. If
persisting, throttling may be raised. However, a setting that is too
high may slow check-in performance. The option allows for a setting
from 0 to 4, with 0 being the least amount of throttling and 4 being the
most. Consult with Customer Support for help in determining if
throttling is advised for your system.

Maximum payloads reached is

30

PN: 1725-36033-001_E.doc

Configuring the SpectraLink 8000 SVP Server

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Missed ding limit

The Missed ding limit defaults to 3 and should be left at this setting
unless advised by Customer Service to raise or lower it. The DING
message is a proprietary method of communication among system
elements. This setting is designed to assist service engineers in fine­tuning system performance and should not be changed without their
consultation.

System Locked

This option is used to take the system down for maintenance. The
default entry is
starting. Return to

Load balancing enables a locked SVP Server to distribute idle
handsets to other SVP Servers in the cluster. Existing calls will not
be interrupted and the SVP Server will become idle once all calls
are ended and idle phones are transferred to another SVP Server.

N (No). Set it at Y (Yes) to prevent any new calls from

N to restore normal operation.

Maintenance Lock

The system automatically sets this option to Y (Yes) after certain
maintenance activities that require reset, such as changing the IP
address.
that the administrator cannot change this option. It is automatically
set by the system. Reset the system at exit to clear

Maintenance Lock prevents any new calls from starting. Note

Maintenance Lock.

Inactivity Timeout (min)

Set the number of minutes the administrative module can be left
unattended before the system closes it. This number can be from 1 to

100. If it is set to zero (0), the administrative module will not close due
to inactivity.

QoS Configuration

Select this option to set the DSCP tags. See QoS Configuration section
below.

PN: 1725-36033-001_E.doc

31

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Reset System

If this option is selected, you will be prompted to reset the SVP Server
upon exiting this screen.

Reset all SVP Servers

If this option is selected, you will be prompted to reset all SVP Servers
upon exiting this screen. This is necessary if you have changed
configurations on other SVP Servers by using the

The SVP Server should be reset at the end of any maintenance
procedure that requires a reset either via Maintenance Lock or
manually via Reset System.

Note that resetting the SVP Server will terminate any calls in
progress.

SendAll option.

32

PN: 1725-36033-001_E.doc

QoS Configuration

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

DSCP tags set packet priorities for QoS.

Configuring the SpectraLink 8000 SVP Server

DSCP Tag

DSCP (Differentiated Services Code Point) is a QoS mechanism for
setting relative priorities. Packets are tagged with a DSCP field in the
IP header for type of service. The decimal value may be set as a
number from 0-63 and may be different for each traffic class listed on
the screen.

• Administration tags set the priority for telnet, TFTP, and other

administrative traffic. Administrative traffic can have the lowest
priority because it does not require voice quality.

• WT (In call) traffic requires voice quality and may be set to a higher

priority than

• RTP traffic is the audio traffic to the IP PBX. It requires voice

quality.

• PBX traffic is not audio to the PBX.

• Inter-SVP2 traffic is the information-passing protocol that SVP

Servers use to communicate with each other.

WT (Standby) traffic.

PN: 1725-36033-001_E.doc

33

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

When forwarding packets, the SVP Server shall always overwrite the
received DSCP value. The final DSCP tag for packets in each of the
traffic classes are assigned a DSCP value based on the following rules.
(Please see table on next page.)

• If both Administration and the Traffic Class setting is Default, the

Default value as shown in the table below will be used.

• If Administration is set at any number (Value X) other than Default,

that setting (Value X) it will override the

Class.

• If any of the Traffic Class settings are set at any value (Value Y)

other than

Administration setting.

Default, that setting (Value Y) will override the

Default value of the Traffic

Traffic Class

WT (In call)
Priority High

WT (Standby)
Priority Med

RTP
Priority High

PBX
Priority Med

Inter-SVP2
Priority Med

Default 4 X
Value Y Y Y
Default 0 X
Value Y Y Y
Default 4 X
Value Y Y Y
Default 0 X
Value Y Y Y
Default 0 X
Value Y Y Y

Administration

Default Value X

Default DSCP settings will mark traffic for Best Effort handling under
normal circumstances. Please consider changing these values
based on the recommended QoS settings from your network
hardware manufacturer to achieve prioritization for your voice traffic.

34

PN: 1725-36033-001_E.doc

Change Password

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

If desired, the password to access the SVP Server may be changed.

A password must meet the following requirements:

• It must be more than four characters, but cannot exceed 16

characters.

• The first character must be a letter.

• Numbers or letters are allowed.

• No dashes, spaces, or punctuation marks, etc. are allowed.

Configuring the SpectraLink 8000 SVP Server

Select

Change Password from the main menu. A screen similar to the

following will appear:

Enter the information and either select Set Password or press the S key
to set the new password.

If you forget a password, call Polycom Customer Service for
assistance.

PN: 1725-36033-001_E.doc

35

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

4

Swapping/Adding/Deleting SVP
Servers

Whenever an SVP Server is removed from the system, wireless
telephones that are using the SVP Server will be affected and calls
may be lost. If the removal of the SVP Server is intentional, the
administrator should lock and idle the system prior to removing an
SVP Server.

Load balancing enables a locked SVP Server to distribute idle
handsets to other SVP Servers in the cluster. Existing calls will not
be interrupted and the SVP Server will become idle once all calls
are ended and idle phones are transferred to another SVP Server.

Adding an SVP Server

A new SVP Server is detected within two seconds of being added to
the system (booted/configured/connected). When detected, wireless
telephones not active in a call will gradually be forced to reboot and
check in again. Any wireless telephone in a call will immediately
switch to the SVP Server that should provide its "timing" function.
This switch should not be noticeable to the user since it is similar to a
normal handoff between APs. When the wireless telephone ends the
call, it will eventually be forced to reboot and check in again. Only a
few handsets at a time are rebooted to prevent excessive check in
traffic on the network. Handsets scheduled to be rebooted can still
make calls and will be rescheduled for reboot when the call is ended.

Removing an SVP Server

The preferred method for removing an SVP Server from an active
system is to first lock the SVP Server. When an SVP Server is locked
for removal from the system, load balancing enables the locked SVP
Server to distribute idle handsets to other SVP Servers in the cluster.
Active calls will not be interrupted. The locked SVP Server will

PN: 1725-36033-001_E.doc

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

become idle once all calls are ended and idle handsets are registered
to other SVP Servers. Once all handsets have been moved---as
evidenced by the number of
screen---the idle SVP Server may be unplugged and removed from
the system.

During this process, there is a short period where a handset registered
on a locked SVP Server may attempt to initiate a call before it is re­registered to another SVP Server. In this case, if there is an unlocked
SVP Server in the cluster, the SVP Server will tell the handset to
reboot. As it reboots, the handset will check-in with an available SVP
Server and the user may then start a call. Handsets registered on
unlocked SVP Servers are not affected.

Of course if a system only has one SVP Server, no calls will be
possible until the removed SVP Server is replaced.

SVP Server Failure

Telephones in Use on the Network Status

If an SVP Server becomes unable to manage calls or fails, any handset
registered to that SVP Server loses service (and any calls) and will
reboot within 30 seconds. After rebooting, the handset will register
with another SVP (if there is one available) and be able to make new
calls. Handsets not registered on the failed SVP may experience a few
seconds of disruption in audio but are otherwise unaffected.

38

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Software Maintenance

The SVP Server uses proprietary software programs written and
maintained by Polycom Corporation. The software versions that are
running on the system components can be displayed via the

Status

screen.

You may obtain information about software updates from Polycom or
its authorized dealer.

At startup the SVP Server uses TFTP to check the software version it
is running against the version in the TFTP location. If there is a
discrepancy, the SVP Server will download the version in the TFTP
location. See the Configuration and Administration document for your
vendor’s IP system for more information about using TFTP.

5

System

Software Updates

Lock the SVP Server in the SVP-II Configuration screen prior to updating
the software. In multiple SVP Server systems, all SVP Servers must be
locked and upgraded at the same time.

Downloads for the SVP Server are available from

http://www.polycom.com/usa/en/support/voice/wi­fi/spectralink_8000_svp_server.html.

After software updates are obtained from Polycom, they must be
transferred to the TFTP location in the LAN to update the code used
by the SVP Server(s).

Note that locking the SVP Server will prevent new calls from
starting. All calls in progress will be terminated when the SVP Server
is reset.

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

6

Troubleshooting via System Status
Menu

Information about system alarms, and network status displays on
various screens accessed through the
is opened from the main menu of the SVP Server. See the previous
sections for directions on how to connect to the SVP Server and
navigate to the

System Status Menu.

System Status Menu screen, which

Error Status - Displays alarm and error message information.

Network Status - Displays information about the Ethernet network to

which the SVP Server is connected.

Software Versions - Lists the software version for each SpectraLink

component.

Gatekeeper Database - Not used in a SIP environment.

Options on the
operation of the components of the system. Use this data to determine

PN: 1725-36033-001_E.doc

System Status Menu provide a window into the real time

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

system function and to troubleshoot areas that may be experiencing
trouble.

Error Status

The Error Status screen displays any alarms that indicate some system
malfunction. Some of these alarms are easily remedied and others
require a call to Polycom’s Customer Support Department.

From the

System Status Menu, select Error Status. The screen displays

active alarms on the SVP Server.

The following table displays the list of alarms and a description of the
action to take to eliminate the alarm.

Alarm Text Action

Maximum payload usage reached Reduce usage, clear alarm2
Maximum telephone usage reached Reduce usage, clear alarm
Maximum access point usage reached Reduce usage, clear alarm
Maximum call usage reached Reduce usage, clear alarm
SRP audio delayed Reduce usage, clear alarm
SRP audio lost Reduce usage, clear alarm
No IP address Configure an IP address
SVP Server(s) lost

Reduce usage or replace lost
SVP Server. Clear alarm

Press C to clear all clearable alarms.

2

If capacity problems persist, additional SVP Servers may need to be added to the system to improve performance.

42

PN: 1725-36033-001_E.doc

Network Status

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

The SVP Server is connected to the Ethernet network, referred to as
the LAN or Local Area Network. The information about that
connection is provided through the

Troubleshooting via System Status Menu

Network Status screen.

From the
information about the Ethernet network. This information can help
troubleshoot network problems. A sample screen is displayed here.

System Status Menu, select Network Status. The screen displays

Ethernet Address – MAC address of the SVP Server (hexadecimal).

System Uptime – The number of days, hours and minutes since the SVP

Server was last reset.

Net – The type of connection to the Ethernet switch currently utilized.

See SVP100 Capacity for more information.

Data is transmitted over SpectraLink components by proprietary
technology developed by Polycom Corporation. The SpectraLink
Radio Protocol (SRP) packets and bytes can be differentiated from
other types of transmissions and are used to evaluate system
functioning by Polycom customer support and engineering
personnel.

PN: 1725-36033-001_E.doc

43

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

RX – Ethernet statistics concerning the received packets during System

Uptime.

bytes – bytes received

packets – packets received

errors – Sum of all receive errors (long packet, short packet, CRC,

overrun, alignment)

drop – packets dropped due to insufficient memory

fifo – overrun occurred during reception

alignment – nonoctet-aligned packets (number of bits NOT

divisible by eight)

multicast – packets received with a broadcast or multicast

destination address

TX – Ethernet statistics concerning the transmitted packets during

System Uptime.

bytes – bytes transmitted

packets

errors

repeated collision, underrun, carrier)

drop

fifo

carrier – carrier lost during transmission

collisions

SVP-II Access Points in Use – APs in use by wireless telephones, either in

– packets transmitted

– Sum of all transmit errors (heartbeat, late collision,

– packets dropped due to insufficient memory

– underrun occurred during transmission

– packets deferred (delayed) due to collision

standby or in a call. ‘Last’ is current, ‘Max’ is the maximum number in
use at one time.

SVP-II Access Points in Calls – APs with wireless telephones in a call.

SVP-II Telephones in Use – wireless telephones in standby or in a call.

SVP-II Telephones in Calls – wireless telephones in a call.

SVP-II SRP Audio (Delay) – SRP audio packets whose transmission was

momentarily delayed.

SVP-II SRP Audio (Lost) – SRP audio packets dropped due to insufficient

memory resources.

44

PN: 1725-36033-001_E.doc

Software Version

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

The SVP Server and wireless telephones utilize Polycom
Corporation’s proprietary software that is controlled and maintained
through versioning. The
about the version currently running on the SVP Server. This
information will help you determine if you are running the most
recent version and will assist Polycom engineering and/or customer
support in troubleshooting software problems.

This screen also displays the model type.

Troubleshooting via System Status Menu

Software Version screen provides information

From the
displayed here.

System Status Menu, select Software Version. A sample screen is

Note that the software versions on your system may be different from
the versions displayed in the above sample screen.

PN: 1725-36033-001_E.doc

45

SpectraLink 8000 SVP Server: Administration Guide for SIP

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

The table below shows the description, major version numbers, and
filenames of the files that are provided when downloading updates.

Name

Table of contents 173 svp100.toc
Functional code 174 zvmlinux
File system 175 flashfs

Major Version
Number

Filename

The minor version numbers for these three files must all match, as
they do in the screen example (17x.024).

46

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Safety Notices

WARNING: Changes or modifications to this equipment not
approved by SpectraLink Corporation may cause this equipment to
not comply with part 15 of the FCC rules and void the user’s
authority to operate this equipment.

WARNING: SpectraLink products contain no user-serviceable
parts inside. Refer servicing to qualified service personnel.

IMPORTANT SAFETY INFORMATION
Follow these general precautions while installing telephone
equipment:

• Never install telephone wiring during a lightning storm.

• Never install telephone jacks in wet locations unless the jack is

specifically designed for wet locations.

• Never touch uninsulated telephone wires or terminals unless
the telephone line has been disconnected at the network
interface.

• Use caution when installing or modifying telephone lines

• When installing Base Stations outside or in buildings other than

the one containing the System Controller, take the following
precaution:
If wiring for a Base Station exits a building—whether to reach
an outdoor Base Station location or to reach a Base Station in
another building—the wiring must be protected at both ends by
a Quick Clip Fuse from Illinois Tool Works, Linx Division, model
number SCP-2X2. The Quick Clip Fuse replaces the bridging
clips on the 66 blocks for all four connections to the non-internal
Base Station.

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

Index

A

Rack mounting .................................................20

Wall mounting..................................................21

Access point, description.....................................14

Administration of .................................................23

Alarms....................................................................42

C

Configuration

Initial setup .......................................................26

Network ............................................................25

QoS.....................................................................33

Software updates..............................................39

SVP Server.........................................................29

Swap, add, delete.............................................37

Customer Support Hotline....................................4

D

Download master .................................................27

Downloading Software Updates ........................39

E

Error Status............................................................42

Ethernet switch, description................................14

F

M

Multiple SVP Servers .............................................9

N

Network Status .....................................................43

P

Password, set and change....................................35

Power......................................................................19

R

Registration Server .................................................9

S

SendAll...................................................................26

Serial Connection..................................................23

Software Updates..................................................39

SpectraLink Voice Priority (SVP)..........................7

SVP010 Server Capacity.......................................10

SVP020 Server Capacity.......................................10

SVP100 Server Capacity.......................................11

Failure.....................................................................38

Front Panel.............................................................16

G

Grounding .............................................................21

T

Telnet......................................................................24

TFTP Download Master.......................................27

Troubleshooting....................................................41

W

H

Hotline......................................................................4

Wireless Telephone, description.........................14

I

Installation

Location.............................................................20

PN: 1725-36033-001_E.doc

VoIPon www.voipon.co.uk [e-mail] Tel: [phone] Fax: [phone]

PN: 1725-36033-001_E.doc