Polycom realpresence group convene Setup Manual

1

ENGLISH

www.polycom.com

© 2015, Polycom, Inc. All rights reserved. POLYCOM® and the names and marks as-

sociated with Polycom’s products are trademarks and/or service marks of Polycom,

Inc. and are registered and/or common law marks in the United States and various

other countries. No portion hereof may be reproduced or transmitted in any form or

by any means, for any purpose other than the recipient’s personal use, without the

express written permission of Polycom.

P/no. MFL69143011 (1503-REV00)

Set Up the Polycom® RealPresence® Group Convene™

Display AC/DC adapter 4 AC Power

adapters

Stand body

Stand base Screws (4 pcs)

(M4 X L10)

Cable cover Rear cover

HDMI cable DC-to-DC jumper

cable

2 Screws and

2 T-Nuts

Easy Setup Guide

*MFL69143011*

ENGLISH

2

ASSEMBLE THE STAND

1

2

3

Use the packing material from the
lower portion of the display as a
platform for assembly.

Do not stand the unit up until the
installation and cabling are complete.

INSTALL THE CAMERA

Unpack the RealPresence Group Series co­dec and camera. Reserve the codec power
supply for future use.

Power supply

Only use the power supply
provided with the display
accessory.

Open the hinge on the camera and insert the hinge into the camera
bracket on the rear top of the display.
Gather the excess cable and secure with the cable ties.

3

ENGLISH

Open the hinge on the camera and insert the hinge into the camera
bracket on the rear top of the display.
Gather the excess cable and secure with the cable ties.

Do not carry display by holding the base.

Do not carry the display upside down by just holding the
base. This may cause the display to fall off the stand and
could result in personal injury.

ENGLISH

4

CONNECT CABLES

Plug the DC-to-DC jumper between the
display and the codec.
Connect and route all cables through the
cable management channel.

Note: Generic cables

If you use generic cables

not certied by LG and

Polycom, the screen may
not display or there may
be image noise.

Install the RealPresence Group Series codec by inserting the T-nuts into
the keyholes on the back of the display.

Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer
to the RealPresence Group Series 500 Setup Sheet for details.

Route the LAN and DC power supply cables between the codec and dis-
play and then through the cable channel at the rear of the stand.

PREPARE THE CODEC

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

5

ENGLISH

INSTALL THE CODEC

Install the RealPresence Group Series codec by inserting the T-nuts into
the keyholes on the back of the display.

Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer
to the RealPresence Group Series 500 Setup Sheet for details.

Route the LAN and DC power supply cables between the codec and dis­play and then through the cable channel at the rear of the stand.

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

ENGLISH

6

Stand Hinge

Cable cover

MANAGE THE CABLES

Arrange the cables so that they run below the stand hinge and then cover
them with the cable cover from the bottom up.
You can disassemble the cable cover by following the assembly instruc­tions in reverse order.

Install the rear cover on the stand by tting the hooks on the cover into

the slots on the back of the display and sliding into place.

7

ENGLISH

INSTALL THE REAR COVER

Install the rear cover on the stand by tting the hooks on the cover into

the slots on the back of the display and sliding into place.

ENGLISH

8

CONNECT THE HEADPHONES (OPTIONAL)

CONNECT POWER

DC Switch

(shipped

with codec)

Caution: Power on DC switch rst.

Power on the DC switch on the bottom of the product
before turning on the display.

Four AC power adapter cables are supplied with the display. Select the ap­propriate AC power adapter cable for your geographic region. Connect the
cable to the power supply input. Connect the AC power cable, provided
with the RealPresence Group Series codec, to the AC power adapter cable.

9

ENGLISH

CONNECT THE HEADPHONES (OPTIONAL)

Bottom Center of

the Display

ENGLISH

10

Power/Menu buttons

POWER ON THE SYSTEM

Power on the display. When the Automatic Standby message appears,
select Yes to disable Automatic Standby. Otherwise, the display will go
into Automatic Power Down after four hours and it will not wake up for
a video call without manually turning on the display. When the codec

nishes booting up, refer to the Polycom RealPresence Group Series
Administrator Guide for details on codec settings conguration and IP

connectivity.

Automatic Standby

Automatic Standby is currently set at 4 hours.
Would you like to disable Automatic Standby?

Yes

No

Press "OK" button to select.

OK EXIT

11

ENGLISH

ADJUST THE ANGLE

Front

Rear

-515

Warnings

-515

When you adjust the angle, do not hold the stand as shown on the

following illustration. You may injure your ngers.

Be careful not to touch or press the screen area when adjusting the
angle of the monitor.

-515

ENGLISH

12

LICENSES

The terms HDMI and HDMI High­Definition Multimedia Interface,
and the HDMI logo are trademarks
or registered trademarks of HDMI
Licensing LLC in the United States
and other countries.

For more information about the components of the RealPresence Group
Series Media Center, refer to the documentation at

http://support.polycom.com/PolycomService/support/us/support/video/
group_series/group_packaged_solutions.html

.