Page 1
Setting Up the Polycom®
RealPresence® EduCart
EagleEye IV Camera
Poles
Base with
Locking Wheels
TM
500
Speakers
Flat Screen Display
Note that your display may
look different than the display
shown in this document.
H Frame
Back
“Grab”
Handles
Cover
Basket
RealPresence
Group 500
Codec
Power Bar
© 2014, Polycom, Inc. All rights reserved. POLYCOM® and the names and marks associated with Polycom’s products are trademarks and/or service marks of
Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. No portion hereof may be reproduced
or transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without the express written permission of Polycom.
www.polycom.com
Polycom, Inc.
6001 America Center Drive
San Jose, CA 95002, USA
1725-08449-001/B
Page 2
Place the base on the floor and lock the wheels.
1
Insert each pole into the base with the threaded
inserts lined up with the holes at the rear of the
base. Loosely insert two 3/8” bolts with flat washers
on the back side and one in the bottom of each pole.
Tighten with a 9/16” wrench.
Loosen and rotate the camera bracket and slide it
3
out to avoid hitting the display during installation.
The camera bracket is rotated for packaging and
must be rotated to the correct position.
Remove the basket and basket bracket from the
2
H frame by removing the two screws circled in
red.
Attach the codec to the H frame with the
4
M3 x 8 Phillips pan head screws.
Setting up the Polycom® RealPresence® EduCartTM 500
2
Page 3
Remove the display from packaging. If possible,
5
leave the display on the bottom portion of the
packaging. Using four long M8 x 25 screws and
spacers between the H frame and the dislay, attach
the H frame to the rear of the display using the
holes indicated below. If the packaging interferes,
either cut the foam or lift the display out.
If this system is not used with a Polycomsupplied display, the display used must have
VESA 400 mm x 400 mm or 400 mm x 600 mm
mounting and must not exceed any of the
following parameters:
Diagonal size: 55” (1400 mm)
Depth: 2.6” (65 mm)
Weight: 66.1 lbs (30 kg)
Note that some displays require M6 screws
that are not supplied.
Ensure that the cart casters are locked. With a
7
person on each side, lift the display, by the handles,
onto the cart at the desired height. Ensure that
all four M8 screws installed in step 6 are hooked
into the keyhole slots in the cart poles. Tighten the
four M8 screws through the holes.
Insert four M8 x 16 screws on the back of the frame
6
and hand tighten to about half way. The screws
must be loose to fit onto the cart.
Loosen the two pre-mounted screws in the codec
8
power supply bracket above the codec. Slide the
power supply into the bracket and tighten the
two screws.
Setting up the Polycom® RealPresence® EduCartTM 500
3
Page 4
Adjust the handles by loosening the two screws
9 11
on each bar (four screws per side). Extend the
handle at or beyond the display by 1-2”. Replace
the screws and tighten. Use the same hole in the
series of holes on both sides. These handles will be
used to move the cart.
Place the speaker inside the grill bracket and
fasten to the bracket with two M5 screws on
each side. Only one side is shown in the photo.
Connect the speaker wires. Refer to the wiring
diagram at the end of this document for details.
Place the speaker brackets grill forward and
10
directly under the display on the outside of the
poles. Attach them with U-shaped brackets using
nuts and a 7/16” wrench.
Attach the vanity plate on the front of
12
the cart between the speakers.
Setting up the Polycom® RealPresence® EduCartTM 500
4
Page 5
Attach the storage basket to the bottom of the H
13
bracket under the power bar using the two screws
removed in step 2.
Loosen the two screws on the camera bracket
15
and lower the camera shelf to the top of the
display. Tighten the screws. Route the camera
cable behind the camera bracket and through
the hole.
Attach the EagleEye IV camera to the camera
14
mounting bracket using four M3 x 6mm Phillips
flat head screws.
Attach and route the cables. Run the power cord
16
from the power bar, down the adjacent pole, and
exit the cord end at the hole at the bottom of the
pole. Run an ethernet cable the same way. Store
excess cable with the cable wrap bracket at the
bottom of the cart base.Refer to the wiring
diagram at the end of this document for details.
Only EduCart 500 components should be
plugged into the power outlet block. Do not
power any other electrical equipment from this
power outlet.
Setting up the Polycom® RealPresence® EduCartTM 500
5
Page 6
Install the magnetic back cover over the codec and
17
cables and fasten with the two supplied screws.
Regulatory Notices and General Warnings:
This equipment is intended for indoor use only.
This equipment is intended to be suitable for institutional use.
Do not use a power cord that is damaged. This could cause
fire or electric shock. Contact the manufacturer for a
replacement cord, if necessary.
Only use a power cord which is appropriately rated and
approved relevant to the country of use.
This equipment should be used only on even surfaces.
This equipment has lockable wheels which should be
applied while the cart is stationary.
When connecting to the mains supply, connect only to an
earthed supply outlet which is installed near the equipment
and is easily accessible.
Keep ventilation openings free from any obstructions.
The ambient operating temperature rating of this equipment
is 0 - 40ºC and should not be exceeded.
Do not immerse the system in any liquid or place any liquids
on it.
Do not spray liquids directly onto the system when cleaning.
Always apply the liquid first to a static-free cloth.
For further information concerning the individual components
of this equipment, please refer to the respective product
literature.
For support or service, please contact your Polycom®
distributor or go to Polycom Support at
www.polycom.com/support.
Child Safety Warnings:
Death or serious injury may occur when children climb on
audio and/or video equipment furniture. A remote control or
toys placed on the furnishing may encourage a child to climb
on the furnishing and as a result the furnishing may tip over
onto the child.
Relocating audio and/or video equipment to furniture not
specifically designed to support audio and/or video
equipment may result in death or serious injury due to
furniture collapsing or overturning onto a child.
Mains Input Rating:
Voltage: 100-240 VAC, 50/60Hz
Current: 3.4A (max)
Weight:
Assembled System: 144 lbs (65 Kgs)
Sampo 55” LED Display (Model PME55MA):
66.1 lbs (30 Kgs)
Setting up the Polycom® RealPresence® EduCartTM 500
6
Page 7
EduCart 500 Wiring Diagram
Setting up the Polycom® RealPresence® EduCartTM 500
7
Loading...