Polycom KIRK 6000, KWS6000 Installation And Configuration Manual

Download

Polycom

KIRK

Wireless Server 6000

Installation and

Configuration Guide

14168000 Version 2.1

KIRK Wireless Server 6000 Installation and Configuration Guide

Catalog No. 14168000

Version 2

Proprietary and Confidential

The information contained herein is the sole intellectual property of Polycom, Inc. No distribution, reproduction or unauthorized use of these materials is permitted without the expressed written consent of Polycom, Inc. Information contained herein is subject to change without notice and does not represent commitment of any type on the part of Polycom, Inc. Polycom and Accord are registered trademarks of Polycom, Inc.

Notice

While reasonable effort was made to ensure that the information in this document was complete and accurate at the time of printing, Polycom, Inc., cannot assume responsibility for any errors. Changes and/or corrections to the information contained in this document may be incorporated into future issues.

Contents

Preface

Introduction to KIRK Wireless Server 6000

Contents

Important Information Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1

Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4

Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5

Components of the KIRK Wireless Server 6000 Solution . . . . . . . . . . . . . 2–2

KIRK Wireless Server 6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2

Wireless Bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3

KIRK Media Resource . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3

Codec Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4

KIRK Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–4

KIRK Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–5

KIRK Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6

Auto Login and Handover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6

KIRK SIO Application Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–6

KIRK Maintenance Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7

Administrative Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7

Requirements for the KIRK Wireless Server 6000 Solution . . . . . . . . . . . . 2–7

KIRK Wireless Server 6000/KIRK Media Resources . . . . . . . . . . . . . 2–7

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–7

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8

KIRK Base Stations and KIRK Repeaters . . . . . . . . . . . . . . . . . . . . . . . 2–8

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8

Electrical Requirements for Base Station . . . . . . . . . . . . . . . . . . . . 2–9

Electrical Requirements for Repeater . . . . . . . . . . . . . . . . . . . . . . . 2–9

KIRK Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10

KIRK Maintenance Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10

Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10

Installation Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–11

KIRK Wireless Server 6000 Installation and Configuration Guide

Deploying KIRK Wireless Server 6000

Recommendations for KIRK Base Station/KIRK Repeater Placement . . 3–2

Deployment of a KIRK Wireless Server 6000 Multi-Cell . . . . . . . . . . . . . . 3–3

Sync over Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3

Examples of Synchronization Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4

Sync Chain With One Sync Master (Primary Sync Ways) . . . . . 3–5

Sync Chain With Alternative Sync Ways . . . . . . . . . . . . . . . . . . . . 3–6

Sync Chain With and Without Alternative Sync Ways . . . . . . . . 3–9

Installing KIRK Wireless Server 6000 and KIRK Media Resource

Description of KWS6000/KIRK Media Resource . . . . . . . . . . . . . . . . . . . . 4–2

Types and Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2

KWS6000 Types and Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . 4–2

KIRK Media Resource Types and Part Numbers . . . . . . . . . . . . . 4–2

KWS6000/KIRK Media Resource Appearance and Components . . 4–3

KWS6000/KIRK Media Resource LED Indicators . . . . . . . . . . . . . . . . 4–5

Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5

Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–5

KWS6000/KIRK Media Resource - Reset Button . . . . . . . . . . . . . . . . . 4–6

Resetting the KWS6000/KIRK Media Resource Hardware . . . . 4–6

Installing the KWS6000/KIRK Media Resource . . . . . . . . . . . . . . . . . . . . . 4–7

Installing KIRK Codec Module

Description of KIRK Codec Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2

KIRK Codec Module Type and Part Number . . . . . . . . . . . . . . . . . . . 5–2

KIRK Codec Module Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–2

Installing the KIRK Codec Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–3

Installing KIRK Base Station

KIRK Base Station Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1

KIRK Base Station provides RF Channels to KIRK Handsets . . . . . . 6–1

KIRK Base Station Types and Part Numbers . . . . . . . . . . . . . . . . . . . . 6–2

KIRK Base Station Appearance and Components . . . . . . . . . . . . . . . . 6–2

KIRK Base Station LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4

Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4

Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4

KIRK Base Station - Reset Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–5

Resetting the KIRK Base Station Hardware . . . . . . . . . . . . . . . . . 6–5

Installing the KIRK Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–5

Wall Mounted (Vertical) Installation RF Coverage . . . . . . . . . . . . . . . 6–5

Recording the Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6

Installing KIRK Repeater

KIRK Repeater Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–1

KIRK Repeater provides RF Channels to KIRK Handsets . . . . . . . . . 6–1

KIRK Repeater Types and Part Numbers . . . . . . . . . . . . . . . . . . . . . . . 6–2

KIRK Repeater - Appearance and Components . . . . . . . . . . . . . . . . . 6–3

KIRK Repeater LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4

Installing the KIRK Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–4

Environmental requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–5

Recording the Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7

Checking Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7

Powering the KIRK Repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7

Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–7

Programming a KIRK Repeater with the KIRK Programming Kit . . . . . 6–7

Content of the KIRK Programming Kit Repeater . . . . . . . . . . . . . . . . 6–7

Set up of the Hardware for Repeater Programming . . . . . . . . . . . . . . 6–8

Programming the KIRK Repeater with the ServiceTool . . . . . . . . . . . 6–9

Use of KIRK Repeater With External Antenna . . . . . . . . . . . . . . . . . . . . . 6–18

Synchronization Ways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–18

Contents

Preparing KIRK Handset for Use

KIRK Handset Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–1

KIRK Handset Types and Part Numbers . . . . . . . . . . . . . . . . . . . . . . . 8–2

KIRK Charger Types and Part Numbers . . . . . . . . . . . . . . . . . . . . . . . 8–2

Power Supply Types and Part Numbers . . . . . . . . . . . . . . . . . . . . . . . 8–3

Installing Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–4

Installing Battery on KIRK 3040 Handsets . . . . . . . . . . . . . . . . . . . . . . 8–5

Installing Battery on KIRK 4020/KIRK 4040/KIRK 4080 Handsets . 8–5

Installing Battery on KIRK 5020 and KIRK 5040 Handsets . . . . . . . . 8–6

Charging KIRK Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–7

Using the Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–7

Charging Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9

KIRK 3040/KIRK 4020/KIRK 4040 and KIRK 4080 Handsets . . 8–9

KIRK 5020/5040 Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–10

Retrieving the Serial Number of the KIRK Handset . . . . . . . . . . . . . . . . 8–12

Retrieving Serial Number on KIRK 3040 Handsets . . . . . . . . . . . . . . 8–12

Retrieving Serial Number on KIRK 4020/KIRK 4040/KIRK 4080

Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–13

KIRK Wireless Server 6000 Installation and Configuration Guide

Retrieving Serial Number on KIRK 5020/5040 Handsets . . . . . . . . 8–14

Basic Network Configuration

Recommended Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–1

Assigning DHCP Server Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–2

Assigning DHCP Server Reservations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–2

Configuring KIRK Wireless Server 6000

Powering up the KWS6000 Server and Media Resource . . . . . . . . . . . . . 10–1

Local Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–2

Connecting a Computer to the KWS6000 . . . . . . . . . . . . . . . . . . . . . . . . . . 10–2

Accessing the Web Based Administration Page . . . . . . . . . . . . . . . . . . . . 10–3

How to Change Internet Protocol Properties using Windows XP . 10–3

How to Access the Administration Page . . . . . . . . . . . . . . . . . . . . . . 10–5

Entering a System User Name and Password . . . . . . . . . . . . . . . 10–6

Configuring a KIRK Wireless Server 6000 Using Static IP Address . . . 10–7

General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–8

Wireless Server Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–9

Built-In Media Resource Configuration . . . . . . . . . . . . . . . . . . . . . . . 10–9

SIP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–10

Security Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–12

Configuring a KIRK Wireless Server 6000 Using DHCP . . . . . . . . . . . . 10–13

General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–13

Wireless Server Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–14

Built-In Media Resource Configuration . . . . . . . . . . . . . . . . . . . . . . 10–15

SIP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–15

Security Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–15

Checking Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10–15

Making a Back-Up of the Configuration File . . . . . . . . . . . . . . . . . . . . . . 10–15

Configuring KIRK Media Resources

Powering up the KIRK Media Resource . . . . . . . . . . . . . . . . . . . . . . . . . . 11–1

Connecting a Computer to the KIRK Media Resource . . . . . . . . . . . . . . 11–2

Accessing the Web Based Administration Page . . . . . . . . . . . . . . . . . . . . 11–3

Configuring a KIRK Media Resource Using DHCP . . . . . . . . . . . . . . . . . 11–6

Local Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–2

How to Change Internet Protocol Properties using Windows XP . 11–3

How to Access the Administration Page . . . . . . . . . . . . . . . . . . . . . . 11–5

Entering a System User Name and Password . . . . . . . . . . . . . . . 11–5

Configuring a KIRK Media Resource Using Static IP Address . . . . . . . 11–7

General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–7

Media Resource Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–7

Checking Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11–7

Making a Back-Up of the Configuration File . . . . . . . . . . . . . . . . . . . . . . . 11–8

Configuring KIRK Base Station

Powering up the KIRK Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–1

Connecting a Computer to the KIRK Base Station . . . . . . . . . . . . . . . . . . 12–2

Accessing the Web Based Administration Page . . . . . . . . . . . . . . . . . . . . 12–3

How to Change Internet Protocol Properties using Windows XP . 12–3

How to Access the Administration Page . . . . . . . . . . . . . . . . . . . . . . 12–5

Entering a System User Name and Password . . . . . . . . . . . . . . . 12–5

Configuring a KIRK Base Station Using DHCP . . . . . . . . . . . . . . . . . . . . 12–6

General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–7

Security Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–7

Sync. Ways Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–8

Configuring a KIRK Base Station Using Static IP Address . . . . . . . . . . . 12–9

General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–10

Base Station Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–11

Security Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–11

Sync. Ways Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–11

Checking Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12–11

Making a Back-Up of the Configuration File . . . . . . . . . . . . . . . . . . . . . . 12–11

Contents

KIRK Handset Registration and Subscription

Registering KIRK Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–1

Subscribing KIRK Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–3

KIRK 3040-Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–3

Subscribing Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–5

Subscribing a Handset to Different Systems . . . . . . . . . . . . . . . . 13–5

KIRK 4020/4040/4080-Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–6

Subscribing Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–8

Subscribing a Handset to Different Systems . . . . . . . . . . . . . . . . 13–8

KIRK 5020/5040/ Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13–9

Creating Login (Subscribing Handset) . . . . . . . . . . . . . . . . . . . . 13–10

Subscribing a Handset to Different Systems . . . . . . . . . . . . . . . 13–11

KIRK Handset Management

Viewing Handset/User Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–2

KIRK Wireless Server 6000 Installation and Configuration Guide

Searching for Handset/User Information . . . . . . . . . . . . . . . . . . . . . . . . . 14–2

Unsubscribing KIRK Handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–3

KIRK 3040/4020/4040/4080 Handset . . . . . . . . . . . . . . . . . . . . . . . . . 14–3

KIRK 5020/5040 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–4

Removing KIRK Handsets from the List (Deregistering) . . . . . . . . . . . . 14–4

Changing User Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–6

Exporting Handset Registration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–7

Restoring Handset Registration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–9

Importing Handset Registration Data - CSV Format . . . . . . . . . . . . . . . 14–11

Adjusting the KIRK Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14–13

Content of the KIRK Programming Kit Handset . . . . . . . . . . . . . . . 14–13

Set up of the Hardware for KIRK Handset Adjustment . . . . . . . . . 14–14

Adjusting the KIRK Handset with the ServiceTool . . . . . . . . . . . . . 14–14

System Management

KIRK Wireless Server 6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–2

Changing System User Name and Password . . . . . . . . . . . . . . . . . . . 15–2

Reading System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–3

General Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–3

Logs Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–4

Wireless Server Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–5

Reading Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–6

Wireless Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–6

Media Resource . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–7

Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–8

Active Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–8

Abnormal Releases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–8

Traffic Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–9

Making a Back-Up of the Configuration File . . . . . . . . . . . . . . . . . . 15–10

Restoring Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–12

Updating the KIRK Wireless Server 6000 . . . . . . . . . . . . . . . . . . . . . 15–13

Updating KIRK Wireless Server 6000 Firmware . . . . . . . . . . . 15–13

Restarting the KIRK Wireless Server 6000 . . . . . . . . . . . . . . . . . . . . 15–14

Operating System of KIRK Wireless Server 6000 . . . . . . . . . . . 15–15

KIRK Wireless Server 6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–16

Administration Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–16

KIRK Media Resource . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–17

Changing System User Name and Password . . . . . . . . . . . . . . . . . . 15–17

Reading System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–18

General Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–18

Logs Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–19

Reading Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–21

Updating the KIRK Media Resource Firmware . . . . . . . . . . . . . . . . 15–21

Updating KIRK Media Resource Firmware . . . . . . . . . . . . . . . 15–21

KIRK Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–23

Changing System User Name and Password . . . . . . . . . . . . . . . . . . 15–23

Reading System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–24

General Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–24

Logs Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–25

Reading Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–26

Sync State of Base Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–26

Checking Sync State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15–27

Updating the KIRK Base Station Firmware . . . . . . . . . . . . . . . . . . . 15–28

Updating KIRK Base Station Firmware . . . . . . . . . . . . . . . . . . . 15–28

Messaging over MSF

Description of Different Types of MSF Messages . . . . . . . . . . . . . . . . . . . 16–1

Sending Text Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16–3

Contents

Regulatory Notices

International Regulatory and Product Information . . . . . . . . . . . . . . . . . 17–1

Important Safety Instructions and Product Information . . . . . . . . . . . . . 17–7

Open Source Software Notice

Open Source Software Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18–1

KIRK Wireless Server 6000 Installation and Configuration Guide

Preface

This guide is intended for qualified technicians who will install, configure and maintain the KIRK Wireless Server 6000 (KWS6000) Solution. To qualify to install the KWS6000 Solution, you must have successfully completed the KWS6000 technical training. The guide provides all the necessary information for successful installation and maintenance of the wireless solutions.

This includes the installation and configuration of:

• KIRK Wireless Server 6000

• KIRK Media Resource

• KIRK Codec Module

• KIRK Base Station

• KIRK Repeater

• KIRK Handset

The Installation Guide also provides you with information about:

• Web based Administration Page of the KWS6000, media resource and base station

Important Information Before You Begin

This guide assumes the following:

• that users have a working knowledge of the call handlers operations

• that the call handler is installed and initialized and is working correctly

• that you have a working knowledge of deployment in general

• that a site survey has been conducted and that the installer has access to

these plans

Note

The site survey should determine the number of handsets and how many RF channels are needed.

1–1

KIRK Wireless Server 6000 Installation and Configuration Guide

Chapter Overview

Where is it? What is it about? When to use it?

Chapter 2 Introduction to KIRK

Wireless Server

Chapter 3 Deploying the KIRK

Wireless Server 6000

Chapter 4 Installing KIRK Wireless

Server 6000 and KIRK Media Resource

Chapter 5 Installing KIRK Codec

Module

Chapter 6 Installing KIRK Base

Station

Chapter 7 Installing KIRK Repeater To learn about the KIRK Repeater

Chapter 8 Preparing KIRK Handset

for Use

Chapter 9 Basic Network

Configuration

6000

To learn about the different components in a typical KWS6000 configuration.

To learn how to deploy a KWS6000 Multi-cell installation.

To learn about KWS6000/KIRK Media Resource and to install it.

To learn about the KIRK Codec Module and to install it in a KIRK Media Resource.

To learn about the KIRK Base Station and to mount it onto wall indoors.

and to mount repeater onto wall or ceiling indoors.

To prepare KIRK Handsets for use, installing and charging battery.

To learn about DHCP and TCP/IP Setup and to assign options to DHCP server.

1–2

Chapter 10 Configuring KIRK

Wireless Server 6000

Chapter 11 Configuring KIRK Media

Resource

To power up the KWS6000, connect a computer to the KWS6000, access the web based Administration Page and configure the KWS6000 using DHCP or TCP/IP Setup.

To power up the KIRK Media Resource, connect a computer to the KIRK Media Resource, access the web based Administration Page and configure the KIRK Media Resource using DHCP or TCP/IP Setup.

Where is it? What is it about? When to use it?

Preface

Chapter 12 Configuring KIRK Base

Station

To power up the KIRK Base Station, connect a computer to the KIRK Base Station, access the web based Administration Page and configure the KIRK Base Station using DHCP or TCP/IP Setup.

Chapter 13 KIRK Handset

Registration and

To register and subscribe KIRK Handsets.

Subscription

Chapter 14 KIRK Handset

Management

To unsubscribe and deregister KIRK Handsets. To change user configuration and adjust handsets.

Chapter 15 System Management To define and view different

settings of the system, reading statistics, making a backup of configuration file, updating system software, and resetting the system.

Chapter 16 Messaging over MSF To enable the MSF messages

function.

Chapter 17 Regulatory Notices To learn about safety regulation for

the KWS6000.

Chapter 18 Open Source Software

Notice

To provide information about the Open Source Software.

1–3

KIRK Wireless Server 6000 Installation and Configuration Guide

Related Documentation

For further information about the KWS6000 not covered by this manual, refer to the following documentation:

Subject Documentation

Deployment Kit Deployment Guide

Handset Operation Handset User’s Guide

Pre and Mid Call Services

Release Notes Every softare release is accompanied by a release

Pre and Mid Call Services User Guide

note. The release note describes software changes, bug fixes, outstanding issues, and hardware compability considerations for the new software release.

Read the release note before you begin a software upgrade!

To obtain the release note, see www.polycom.com

1–4

Acronyms

Preface

AC Authentication Code

ARI no. Access Rights Identity - Serial number of the KWS6000

CLI Command Line Interface

dB Decibels (deciBells)

DECT Digital Enhanced Cordless Telecommunications

DHCP Dynamic Host Configuration Protocol

DNS Domain Name System

e.i.r.p. Equivalent Isotropic Radiated Power

GAP Generic Access Profile

HW PCS Hardware Product Change Status - Hardware edition

IP Internet Protocol

IPEI International Portable Equipment Identity - Serial number of the

handset - SN

IWU Inter Working Unit

KWS KIRK Wireless Server

KWS6000 KIRK Wireless Server 6000

LAN Local Area Network

LED Light Emitting Diode

MAC Media Access Control - hardware address of a device connected to

a network

MTU Maximum Translation Unit

MWI Message Weighing Indication

NIC Network Interface Card

NTP Network Time Protocol

PBX Private Branch eXchange

PCS Product Change Status (Edition)

PoE Power over Ethernet

PP Portable Parts - wireless handset

RSSI Received Signal Strength Indicator

RTP Real-time Transport Protocol

SIP Session Initiated Protocol

SW PCS Software Product Change Status - Software edition

TFTP Trivial File Transfer Protocol

UDP User Datagram Protocol

1–5

KIRK Wireless Server 6000 Installation and Configuration Guide

VoIP Voice over Internet Protocol

WLAN Wireless Local Area Network

WRFP Wireless Radio Fixed Part - Wireless Repeater

1–6

Introduction to KIRK Wireless Server 6000

This section provides a description of the KWS6000 solution.

A typical KWS6000 configuration includes a number of the following components, in addition to the KWS6000:

• Media resources

• Base stations

• Repeaters

• Handsets and accessories

Figure 2-1 Overview of the Whole Solution

2–1

KIRK Wireless Server 6000 Installation and Configuration Guide

This section provides information about:

• “Components of the KIRK Wireless Server 6000 Solution” on page 2-2

• “Requirements for the KIRK Wireless Server 6000 Solution” on page 2-7

• “Installation Prerequisites” on page 2-11

Components of the KIRK Wireless Server 6000 Solution

This section provides information about:

• “KIRK Wireless Server 6000” on page 2-2

• “Wireless Bands” on page 2-3

• “KIRK Media Resource” on page 2-3

• “KIRK Base Station” on page 2-4

• “KIRK Repeater” on page 2-5

• “KIRK Handset” on page 2-6

• “KIRK Maintenance Software” on page 2-7

• “Administrative Computer” on page 2-7

KIRK Wireless Server 6000

Below you will find an overview of the system capacity of the KWS6000.

Table 2-1 Overview of System Capacity

Description Capacity

Max. number of base stations.

Note: A minimum of 1 base station is required, as the KWS6000 does not have a built-in radio.

Max. number of simultaneous calls on each base station 11

Max. number of repeaters on each base station 6

Max. number of simultaneous calls on a KWS6000/media resource (G.711)

Max. number of media resources 32

Max. number of simultaneous calls with 32 media resources 1024

255

2–2

Introduction to KIRK Wireless Server 6000

Table 2-1 Overview of System Capacity

Description Capacity

Wireless Bands

Max. number of simultaneous calls on each KWS6000/media resource with Codec Module

Max. number of simultaneous calls with 32 media resources with Codec Module.

768

Note: If the Codec Module is used, it is recommended to install it in al media resources.

Max. number of registered handsets

4096

The KWS6000 controls the wireless infrastructure. It manages media resources, base stations, repeaters and the IP interface to the call handler.

The communication protocol between the KWS6000 and the call handler is SIP

A KWS6000 is installed directly on the LAN and must be managed as part of the corporate network.

For more information about the KWS6000, refer to “Deploying KIRK Wireless

Server 6000” on page 3-1, “Installing KIRK Wireless Server 6000 and KIRK Media Resource” on page 4-1 and “Configuring KIRK Wireless Server 6000”

on page 10-1.

The wireless solution supports two wireless bands, allowing operation in various countries and regions. Supported wireless bands are:

• ETSI DECT (1880-1900 Mhz), referred to as DECT

• USA DECT (1920-1930 Mhz), referred to as 1G9

The wireless band used by a KWS6000 solution is determined by the base stations and handsets ordered with the solution.

KIRK Media Resource

The media resource performs media conversion between the call handler and the KWS6000 and is the media termination point for incoming and outgoing calls.

A maximum of 32 media resources can be added to a KWS6000. Each media resource adds 32 voice channels to the system. Adding 32 media resources makes it possible to have 1024 calls at the same time.

Note

The KWS6000 contains one media resource.

2–3

KIRK Wireless Server 6000 Installation and Configuration Guide

Codec Module

It is possible to install a Codec Module in the media resource. The Codec Module adds a number of codecs, allowing the wireless server to interface to G.729A/G.723.1 and other codec standards.

Note

KIRK Base Station

When installing a Codec Module, the media resource only adds 24 voice channels to the system. Adding 32 media resources with codec modules makes it possible to have 768 calls at the same time.

For more information about media resources, refer to “Installing KIRK

Wireless Server 6000 and KIRK Media Resource” on page 4-1 and “Configuring KIRK Media Resources” on page 11-1.

For more information about installing the Codec Module, refer to “Installing

KIRK Codec Module” on page 5-1.

The base stations are positioned in the area to send and receive calls between the wireless server and the handset. The base station contains internal antennas and handles 11 speech channels simultaneously. A base station is able to synchronize with other base stations. When the base station is synchronized with other base stations, a person speaking in a handset can move between base stations without any interference.

Transmission length is up to 100 meters/329 feet according to IEEE 802.3u on a twisted pair cable, e.g. cat.5e. The base station is a class 1 PoE device (802.3af) and must be powered accordingly (maximum power supply consumption

3.0W according to PoE 802.3af). The radius coverage of the base station is up

to 90 meters/295 feet indoor and up to 300 meters/984 feet outdoor, with a handset in line-of-sight.

Coverage area decreases depending on choice of building materials and obstructive elements. To ensure proper coverage in the areas required, it is necessary to conduct a site survey and deployment by certified technicians. For more information about deployment, refer to the Deployment Guide accompanying the Deployment Kit.

For more information about the base station, refer to “Installing KIRK Base

Station” on page 6-1 and “Configuring KIRK Base Station” on page 12-1.

2–4

KIRK Repeater

Introduction to KIRK Wireless Server 6000

The repeater can be used to extend the coverage area in a wireless solution. Depending on the repeater type, it can be mounted either on the wall or on the ceiling. The wireless repeater is used in areas with limited voice traffic, where cabling is difficult. The repeater does not increase the number of traffic channels, but increases the coverage area established with the base station. Up to three repeaters can be placed in cascade formation directing coverage in a certain direction.

The base station can support up to 6 repeaters.

For more information about the repeater, refer to “Installing KIRK Repeater” on page 6-1.

2–5

KIRK Wireless Server 6000 Installation and Configuration Guide

KIRK Handset

The handset is a lightweight, ergonomically designed wireless unit that includes an LCD display and keypad.

The handset is a portable unit compatible with DECT GAP standard.

The handset is designed to provide the subscriber with most of the features available for a wired phone, in addition to its roaming and handover capabilities.

The KWS6000 supports up to 4096 registered handsets.

For more information about the handset, refer to “Preparing KIRK Handset for

Use” on page 8-1, “KIRK Handset Registration and Subscription” on page 13-1

and “KIRK Handset Management” on page 14-1.

Auto Login and Handover

Auto login refers to the ability to log on to more than one system, enabling you to use the same handset on up to 10 different systems. If a handset is subscribed to two or more systems, you can use Auto Login type A or Auto Login type B to change between the systems automatically:

• Auto Login type A is used if a handset is subscribed to two or more systems. Auto Login A should only be used in separate systems without overlaps.

• Auto Login type B is used if a handset is subscribed to two systems only. Auto Login B can be used in separate systems which are overlapping each other.

Note

Auto Login type B is only supported in 4020/4040/4080 Handsets.

For more information about Auto Login, refer to “Subscribing KIRK

Handsets” on page 13-3.

Handover refers to the ability to move between the coverage areas of different radio units on the same system while talking, without interruptions in the conversation.

KIRK SIO Application Interface

The SIO Application Interface is a communication platform allowing text messaging between the wireless server and a handset. With the SIO API, which is a fundamental part of all our solutions, and a third party application program, the customer is offered a wide range of usage opportunities in a variety of vertical markets.

2–6

KIRK Maintenance Software

The following software application for the installation and maintenance of the KWS6000 Solution is provided:

• ServiceTool

Used for programming of the repeater, adjustment of the handset and software download to repeater/handset.

Introduction to KIRK Wireless Server 6000

Note

ServiceTool is not used for adjustment of the 5020 Handset.

The ServiceTool application can be downloaded from www.polycom.com.

Administrative Computer

An administrative computer is required for configuration and maintenance of the KWS6000, media resource and base station. This computer may be temporarily connected directly to the device or to the network. A dedicated computer is not required.

Requirements for the KIRK Wireless Server 6000 Solution

This section provides information about the environmental and electrical requirements and software requirements for the KWS6000 solution.

KIRK Wireless Server 6000/KIRK Media Resources

Environmental Requirements

The installation area must:

• be clean, free of traffic and excess dust, dry, and well ventilated

• be within the temperature ranges of 10°C and 40°C/50°F and 104°F

• be between 20% and 80% non-condensing relative humidity

Note

The installation area must be of sufficient height from the floor to prevent water damage.

2–7

KIRK Wireless Server 6000 Installation and Configuration Guide

Electrical Requirements

The following electrical requirements must be met:

• Power consumption: 8V/500 mA

• Typical power consumption: 5W per unit

• The supplied power for the AC adaptor power supply must be 110 to 240

ac nominal, 50/60 Hz.

• Power supply must be LPS

KIRK Base Stations and KIRK Repeaters

Environmental Requirements

• Avoid installing base stations and repeaters on large concrete or marble columns because these columns affect radio coverage. If possible, place the base station a minimum of one meter/3.3 feet from these types of columns.

• Do not install a base station or repeater with the antenna housings near metal objects. Be careful not to damage existing wiring or panels.

• Do not position base stations and repeaters in ducts, plenums, or hollow spaces used to transport environmental air except where the duct, plenum or hollow space is created by a suspended ceiling having lay-in panels. When you need more than one base station in a cell to meet traffic requirements, position the base stations at the same cell center.

• Keep the base station and repeater away from steel constructions.

• Do not position base stations and repeaters directly on metallic surfaces. If

possible, place the base station a minimum of one meter/3.3 feet from these types of surfaces.

• Do not position base station and repeaters behind furniture.

• Only position base stations and repeaters where the signal is needed.

• The installation area must be clean, free of traffic and excess dust, dry, and

well ventilated.

• The installation area must be within the temperature ranges of 10°C and 40°C/50°F and 104°F.

• The installation area must be between 20% and 80% non-condensing relative humidity.

2–8

Introduction to KIRK Wireless Server 6000

• Minimum distance between two base stations varies depending on material and construction of buildings, but there must always be synchronization chains and radio coverage overlap between the two base stations or handover between radio units. The time it takes a person to cross the common coverage area must be 10 seconds or more, as the handset needs time to scan for an alternative base station.

Electrical Requirements for Base Station

The following electrical requirements must be met:

• The base station operates on standard twisted pair ethernet cable - e.g. minimum Cat.5e - to prevent disturbances from other equipment.

• Maximum power supply consumption is 3.0W (IEEE 802.3af class 1 device).

• The max. radiated output power for the antenna is 10mW e.i.r.p/channel.

Electrical Requirements for Repeater

• The supplied power (power supply) for the charger must be 110 V to 120 V ac nominal (or 220 V to 230 V ac nominal), 50/60 Hz.

2–9

KIRK Wireless Server 6000 Installation and Configuration Guide

KIRK Handsets

Environmental Requirements

• The area where the handset is used must be within the temperature ranges of 0°C and 40°C/32°F and 104°F.

• For correct battery charging, the room temperature must be between 0°C and 25°C/32°F and 77°F. Therefore, the handset must not be placed in direct sunlight. The battery has a built-in heat sensor which will stop charging if the battery temperature is too high.

• For battery information, refer to “Installing Battery” on page 8-4.

• The area where the handset is used must be between 20% and 80%

non-condensing relative humidity.

Electrical Requirements

The following electrical requirement must be met:

• The supplied power (power supply) for the charger must be 110 V to 120 V ac nominal (or 220 V to 230 V ac nominal), 50/60 Hz.

KIRK Maintenance Software

This section describes the computer requirements to run the installation and maintenance tools of the handset and repeater.

Software Requirements

• OS: Windows 2000 (SP4), Windows XP (SP2), Windows Vista

• CPU: Minimum 400MHz (2000/XP), 1GHz (Vista)

• RAM: Minimum 256 MB (2000/XP), 1 GB (Vista)

• GPU/Display: XGA (1024x768)

• Harddisk: Minimum recommended harddisk size by OS and other

installed applications + 25 MB free space for the application.

Note

Depending on other applications running on the system, CPU, RAM and harddisk may vary.

2–10

Installation Prerequisites

Introduction to KIRK Wireless Server 6000

Note

Ensure that a site survey and deployment have been conducted and that the installer has access to these plans before proceeding any further. For more information about deployment, refer to “Deploying KIRK Wireless Server

on page 3-1.

6000”

Before you start the installation you need to find the following information and perform the following tasks:

• ARI codes (serial numbers) for the KWS6000 (see label on the rear of the KWS unit)

• Serial numbers for handsets. Refer to “Retrieving the Serial Number of the

KIRK Handset” on page 8-12.

• AC codes (authentication codes)

The AC is a customer-defined optional subscription pin code of a maximum of eight digits for the individual handset. The AC can be used when connecting the handset to the KWS.

• Repeaters:

Mark each repeater with the number of the related base station. This way you can easily configure the system on site.

• Handsets:

To use the handsets, you must first install the radio infrastructure, e.g. base stations and repeaters to transmit and receive radio signals to and from the handsets. There are no direct connections between the handset and the system. For more information about base station and repeater installation, refer to “Installing KIRK Base Station” on page 6-1 and

“Installing KIRK Repeater” on page 6-1.

• Charging battery

When charging the handset battery for the first time, leave the handset in the charger for 14 - 16 hours to ensure that the battery is fully charged and the handset ready for use. Refer to “Charging KIRK Handsets” on page 8-7.

2–11

KIRK Wireless Server 6000 Installation and Configuration Guide

2–12

Deploying KIRK Wireless Server 6000

Before you install the KWS6000 solution, it is necessary to perform a complete site survey and determine the exact location of KWS6000, base stations, repeaters and number of handsets required.

A wel l planned installat ion shoul d start wit h an RF cove rage site s urvey. A si te survey is designed to determine the optimal location for base stations and repeaters and the amount of wireless voice traffic to be supported by the installation (i.e., how many handsets must maintain voice conversations at the same time, in any given area).

Due to the unexpected nature of RF propagation in an indoor environment, an actual on-site test must be performed before the installation is complete. While an extensive guide to effective RF coverage planning is outside the scope of this manual, the following points should be taken into consideration when planning the site, prior to base station and repeater installation:

• The base station/repeater provides typical RF coverage of up to 50 meters/164 feet in a typical indoor office environment and up 300 meters/984 feet in an open area (line-of-sight), extending in all directions from the base station/repeater. The exact coverage range depends on the building architecture, wall material and surroundings.

• The wireless solution can support a maximum of 4096 handsets.

• The wireless solution supports a maximum of 255 base stations.

• Handset handover: handsets can move between coverage areas of base

stations and repeaters while receiving continuous service and maintaining conversations in progress.

• For efficient handover of conversations between base stations, deploy base stations with wide overlap between them (i.e., plan for some areas to be covered by more than one base station). Overlaps are necessary to maintain seamless handover and to establish synchronization chains. A good example may be a cafeteria during lunch hour where temporary

3–1

KIRK Wireless Server 6000 Installation and Configuration Guide

concentrations of handsets may occur. The overlap carries the excess call load to adjacent base station to provide uninterrupted services to subscribers.

• Typically, installations such as office buildings, hotels and hospitals should be equipped with base stations/repeaters on several floors to create uniform and complete RF coverage.

• Open areas can be covered with a sparse network of base stations. In such applications, the base stations/repeaters cover an extended range due to the extended line-of-sight RF propagation capability.

• Ensure that there is not a residential DECT system (home DECT) on the site.

This section provides information about:

• “Recommendations for KIRK Base Station/KIRK Repeater Placement” on

page 3-2

• “Deployment of a KIRK Wireless Server 6000 Multi-Cell” on page 3-3

Recommendations for KIRK Base Station/KIRK Repeater Placement

• In large halls, the base station/repeater (wall) should be installed vertically in the middle of the space below the drop ceiling.

• In corridors, the base station/repeater (wall) should be installed vertically preferably at corridor intersections where propagation patterns follow the corridor patterns. The base station/repeater should point towards the corridor and preferably in the middle height between the floor and the actual ceiling. In case there are high objects in the area, the base station/repeater (wall) should be installed above those objects but still kept distant from the ceiling.

• The repeater (ceiling) should be installed in the middle of corridors and small rooms.

• In multi-story buildings, base stations/repeaters may be installed on opposite sides of the floors to take advantage of the floor-to-floor coverage. The coverage design cannot rely entirely on floor-to-floor propagation; each case must be verified due to variations in local attenuation patterns.

• If the building contains a central open space area with windows to the other areas, base stations/repeaters may be installed in this open space to provide a good coverage for the rooms in the inner circle on all floors (e.g. hotels).

3–2

Deploying KIRK Wireless Server 6000

• If a base station/repeater (wall) hangs vertically on a wall, the RF coverage in front of the base stations/repeaters is twice as large as the coverage at the rear. When a base station/repeater is installed on the outside of an outer wall, the RF coverage behind it is strongly attenuated by the wall.

• Base stations/repeaters should not be installed near large metallic objects.

• Reinforced concrete structures have a high attenuation factor inside the

building. They decrease the RF coverage range of the base stations/repeaters and therefore requires a higher number of base stations/repeaters in the building. Lighter types of construction require fewer base stations since attenuation figures are considerably lower.

Deployment of a KIRK Wireless Server 6000 Multi-Cell

Sync over Air

Note

This section only contains deployment information specific to the KWS6000. For more information about deployment in general, refer to the Deployment Guide accompanying the Deployment Kit. The Deployment Guide provides instructions on how to use the Deployment Kit to determine the most suitable locations for the different radio units.

As a user moves from one base station radio coverage area to another, the call must be handed over to the next radio unit. To create handover between radio units it is necessary to establish synchronization chains. For more information about synchronization chains, refer to “Examples of Synchronization Chains” on page 3-4. If the synchronization between radio units is lost, then handover is not possible and ongoing calls will be terminated.

Each base station must be placed within the radio coverage area of at least one other base station or repeater (radio units).

3–3

KIRK Wireless Server 6000 Installation and Configuration Guide

Examples of Synchronization Chains

Certain rules must be taken into consideration when establishing synchronazation chains:

• The distance over which synchronization can take place is limited to a distance similar to a loss of max. 25 dB. If the loss of signal is higher than 25 dB, there is no guarantee that synchronization is stable.

Note

It is recommended that a base station synchronizes with at least two other radio units, that an alternative sync way is defined to ensure system redundancy. If the primary sync way is not working, then the alternative sync way takes over and the synchronization chain is not broken.

Synchronization chains for the KWS6000 Solution can be made with base stations and repeaters.

As you can only configure a repeater to synchronize on one radio ID, it is not possible to define alternative sync ways for repeaters.

As the KWS6000 uses the DECT interface to synchronize on, one base station is configured as the Sync Master.

This section provides information about:

• “Sync Chain With One Sync Master (Primary Sync Ways)” on page 3-5

• “Sync Chain With Alternative Sync Ways” on page 3-6

• “Sync Chain With and Without Alternative Sync Ways” on page 3-9

3–4

Deploying KIRK Wireless Server 6000

• The synchronization chain must always overlap with the base station to sync on.

•No.0 is the Sync Master (can be numbered 0-255).

• Other radio units are connected to the Sync Master through the

synchronization chain.

• If one of the radio units in the synchronization chain is not working, then the synchronization chain is broken and the system will be unstable.

•No. 0 is the Sync Master (can be numbered 0-255).

Note: It is recommended to place the Sync Master in the middle of the building.

• Green line: Shows the primary sync ways.

• Brown line: Only handover overlap is needed.

Note: It is recommended to make a site planner. Every base station must be numbered with Radio ID, Primary sync Radio ID, and Alternative

sync Radio ID.

Sync Chain With One Sync Master (Primary Sync Ways)

Figure 3-1 Synchronization Chain

Figure 3-2 Synchronization Chain Layout without Alternative Sync Ways

3–5

KIRK Wireless Server 6000 Installation and Configuration Guide

•No. 0 is the Sync Master (can be numbered 0-255).

•No. 10 and No. 20: Primary and alternative sync on No. 0.

•No. 11: Primary sync on No. 10 and alternative sync on No. 21.

•No. 21: Primary sync on No. 20 and alternative sync on No. 11.

Sync Chain With Alternative Sync Ways

Figure 3-3 Synchronization Chain with Alternative Sync Ways

3–6

Deploying KIRK Wireless Server 6000

•No. 0 is the Sync Master (can be numbered 0-255).

•No. 10 and No. 20: Primary and alternative sync on No. 0.

•No. 11: Primary sync on No. 10 and alternative sync on No. 21.

•No. 21: Primary sync on No. 20 and alternative sync on No. 11.

•No. 0 is the Sync Master (can be numbered 0-255).

•No. 10, No. 20, No. 30, and No. 40: Primary and alternative sync on No. 0.

•No. 11: Primary sync on No. 10 and alternative sync on No. 21.

•No. 21: Primary sync on No. 20 and alternative sync on No. 11.

•No. 31: Primary sync on No. 30 and alternative sync on No. 41.

•No. 41: Primary sync on No. 40 and alternative sync on No. 31.

In the example below, base station No. 10 is down. As a consequence, base station No. 11 must use the alternative sync way on No. 21.

Figure 3-4 Synchronization Chain with Alternative Sync Ways

Figure 3-5 Synchronization Chain with Alternative Sync Ways

3–7

KIRK Wireless Server 6000 Installation and Configuration Guide

•No. 0 is the Sync Master (can be numbered 0-255).

Note: It is recommended to place the Sync Master in the middle of the building.

• Green line: Shows the primary sync ways.

• Red line: Shows the alternative sync ways.

Note: It is recommended to make a site planner. Every base station must

be numbered with Radio ID, Primary sync Radio ID, and Alternative sync Radio ID.

Figure 3-6 Synchronization Chain Layout with Alternative Sync Ways

3–8

Deploying KIRK Wireless Server 6000

•No. 0 is the Sync Master (can be numbered 0-255).

•No. 10 and No. 20: Primary and alternative sync on No. 0.

•No. 11, No. 12 and No. 13: Only primary sync.

•No. 14 and No. 15: Primary sync and alternative sync.

•No. 21, No. 22 and No. 23: Only primary sync.

•No. 41: Primary sync on No. 40 and alternative sync on No. 31.

•No. 11 and No. 21: Only handover overlap (Marked with green).

Sync Chain With and Without Alternative Sync Ways

Figure 3-7 Synchronization Chain With and Without Alternative Sync Ways

3–9

KIRK Wireless Server 6000 Installation and Configuration Guide

•No. 0 is the Sync Master (can be numbered 0-255).

•No. 10 and No. 20: Primary and alternative sync on No. 0.

•No. 74, No. 138 and No. 202: Repeater - no alternative sync possible.

•No. 14 and No. 15: Primary sync and alternative sync on repeater.

•No. 84, No. 148 and No. 212: Repeater - no alternative sync possible.

•No. 24 and No. 25: Primary sync and alternative sync.

•No. 74 and No. 84: Only handover overlap (Marked with green).

Figure 3-8 Synchronization Chain With Repeaters

3–10

Installing KIRK Wireless Server 6000 and KIRK Media Resource

This section provides a description of the KWS6000 and media resource. The section also provides information about resetting the KWS6000 hardware using the Reset button on the KWS6000/media resource faceplate.

Note

The installation of a media resource is optional. Installation of a media resource will augment the number of simultaneous voice calls supported by a stand-alone server.

Before you install the equipment, ensure that a site planner defines the locations of the KWS6000 and media resources.

This section contains the following information:

• “Description of KWS6000/KIRK Media Resource” on page 4-2

• “Installing the KWS6000/KIRK Media Resource” on page 4-7

4–1

KIRK Wireless Server 6000 Installation and Configuration Guide

Description of KWS6000/KIRK Media Resource

This section contains information about:

• “KWS6000 Types and Part Numbers” on page 4-2

• “KWS6000/KIRK Media Resource Appearance and Components” on

page 4-3

• “KWS6000/KIRK Media Resource LED Indicators” on page 4-5

• “KWS6000/KIRK Media Resource - Reset Button” on page 4-6

Types and Part Numbers

KWS6000 Types and Part Numbers

The KWS6000 contains RF circuitry that comply with the local band standards: ETSI DECT and USA DECT 6.0. The table below includes a list of available KWS6000 and their part numbers.

Table 4-1 KIRK Wireless Server 6000 Part Numbers

Variants of KIRK Wireless Server 6000 Part Number

KIRK Wireless Server 6000 1.8/1.9 GHz

• with SIP Protocol

For more information about SIP variants go to www.polycom.com

02344100

KIRK Media Resource Types and Part Numbers

The media resource contains RF circuitry that comply with the local band standards: ETSI DECT and USA DECT 6.0. The table below includes a list of available media resources and their part numbers.

Table 4-2 KIRK Media Resource Part Numbers

Variants of KIRK Media Resources Part Number

KIRK Media Resource 1.8/1.9 GHz

• with SIP Protocol

02344200

4–2

Installing KIRK Wireless Server 6000 and KIRK Media Resource

LED

KWS6000/KIRK Media Resource Appearance and Components

The KWS6000/media resource front cover includes the following:

• LED that indicates the operating status of the unit

Figure 4-1 KWS6000/Media Resource - Front view

4–3

KIRK Wireless Server 6000 Installation and Configuration Guide

ETH Port

Power Supply

Power Indicator

Reset Button

LINK/Activity Indicator

The KWS6000/media resource faceplate includes the following (see figure below).

Figure 4-2 KWS6000/Media Resource - Faceplate

For information about the Reset button, refer to “Resetting the

KWS6000/KIRK Media Resource Hardware” on page 4-6.

4–4

Installing KIRK Wireless Server 6000 and KIRK Media Resource

KWS6000/KIRK Media Resource LED Indicators

Front Cover

The KWS6000/media resource front cover has one indicator describing the faults and failures of the device. The indicator is off when the KWS6000/media resource is not powered. The LED flashes when the KWS6000/media resource initializes. The indicator is on when the KWS6000/media resource is operating.

Table 4-3 LED Indicator Description - Front Cover

LED Indicator Meaning

Steady green OK and idle

Slow green flashing OK and active voice call

Fast green flashing Active, in operation with the maximum active

connections (busy)

Slow red flashing Missing media resource or base station (if it is a

media resource: missing connection to KWS6000)

Fast red flashing Error

Steady red Reset/shutdown in progress

Steady red for 5 seconds followed by fast red flashing

Reset to factory settings

Faceplate

Table 4-4 LED Indicator Description - Faceplate

LED Indicator Meaning

LINK/Activity Indicator - green Link layer software has established

connection

LINK/Activity Indicator - green flashing

Power Indicator - green KWS6000 is connected to Power

Activity

4–5

KIRK Wireless Server 6000 Installation and Configuration Guide

KWS6000/KIRK Media Resource - Reset Button

It is possible to restart or reset the KWS6000/media resource by pressing the Reset button on the faceplate of the KWS6000/media resource. For description of the faceplate, refer to “Faceplate” on page 4-5.

Resetting the KWS6000/KIRK Media Resource Hardware

This section contains a description of the different actions that take place when pressing the Reset button.

Table 4-5 Reset Button Description

Press button Action

Short press (2 to 5 sec.) System restarts when button is released.

Long press (5 to 9 sec.) until front LED flashes red, then release button

Resets the system to factory default settings (original IP settings and empty user data base) and restarts the system.

Firmware version is not affected.

4–6

Installing KIRK Wireless Server 6000 and KIRK Media Resource

Installing the KWS6000/KIRK Media Resource

The KWS6000/media resource is suitable for mounting indoors on a wall.

1 Mount the KWS6000/media resource on the wall, using the anchors and

screws provided.

Note: When you place the KWS6000/media resource on the screws, ensure that the screws do not touch the printed circuit board.

Figure 4-3 KWS6000/Media Resource Wall Mounting

2 Connect the wire into the RJ45 plug on the KWS6000/media resource.

4–7

KIRK Wireless Server 6000 Installation and Configuration Guide

4–8

Installing KIRK Codec Module

This section provides a description of the Codec Module and describes how to unpack and install it in a media resource. The Codec Module adds a number of codecs, allowing the wireless server to interface to G.729A/G.723.1 and other codec standards.

Note

When installing a Codec Module, the media resource only adds 24 voice channels to the system. Adding 32 media resources with codec cards makes it possible to have 768 calls at the same time.

For more information about media resources, refer to “Installing KIRK

Wireless Server 6000 and KIRK Media Resource” on page 4-1.

This section contains the following information:

• “Description of KIRK Codec Module” on page 5-2

• “Installing the KIRK Codec Module” on page 5-3

5–1

KIRK Wireless Server 6000 Installation and Configuration Guide

Description of KIRK Codec Module

This section contains information about:

• “KIRK Codec Module Type and Part Number” on page 5-2

• “KIRK Codec Module Appearance” on page 5-2

KIRK Codec Module Type and Part Number

Table 5-1

Codec Module for KIRK Wireless Server 6000 Part Number

KIRK Codec Module 1.8/1.9 GHz (conforms with standard DECT markets)

KIRK Codec Module Part Number

KIRK Codec Module Appearance

Figure 5-1 Codec Module

02344300

5–2

Installing the KIRK Codec Module

This section describes how to install the Codec Module in a media resource.

Installing KIRK Codec Module

Note

Installation must be performed by authorized personal only and must be performed at an approved ESD workstation.

How to install the Codec Module 1 Power off the media resource. 2 Remove the cover of the media resource carefully:

— Place the media resource face down on a desk.

— Apply sufficient pressure to the tabs located at each of the four corners

of the unit while gently lifting the cover from the chassis.

— Once separated, set the front cover aside in a safe location.

3 Snap the two support posts into the printed circuit board of the media

resource.

4 Carefully insert the Codec Module into the Codec Module connector and

the two support posts on the printed circuit board.

Figure 5-2 Installing Codec Module on Pinted Circuit Board

5 Replace the cover by aligning the tabs with the proper positions and

6 Connect the LAN cable to the media resource. 7 Power up the media resource.

gently press the cover onto the chassis until the tabs lock into place.

5–3

KIRK Wireless Server 6000 Installation and Configuration Guide

8 When accessing the web based Administration Page of the KWS6000

under Administration/Media Resource, you can now see that more codecs are available.

For information about accessing the web based Administration Page, refer to “Accessing the Web Based Administration Page” on page 10-3.

5–4

Installing KIRK Base Station

This section provides information about the base station and how to install it.

Before you install the equipment, ensure that a site planner defines the location of the base stations.

This section includes information about:

• “KIRK Base Station Description” on page 6-1

• “Installing the KIRK Base Station” on page 6-5

• “Recording the Installation Information” on page 6-6

KIRK Base Station Description

This section contains information about:

• “KIRK Base Station provides RF Channels to KIRK Handsets” on page 6-1

• “KIRK Base Station Types and Part Numbers” on page 6-2

• “KIRK Base Station Appearance and Components” on page 6-2

• “KIRK Base Station LED Indicators” on page 6-4

• “KIRK Base Station - Reset Button” on page 6-5

KIRK Base Station provides RF Channels to KIRK Handsets

The base station is a compact device that contains RF circuitry and transmit/receive antennas. The main function of the base station is to provide audio and data communication between the handsets and the KWS6000. The base station supports 11 RF channels for DECT or USA DECT bands.

Note

The base station is also termed by some manufacturers as the RFP (Radio Fixed Part).

6–1

KIRK Wireless Server 6000 Installation and Configuration Guide

LED

The RF communication is provided according to the band standard at the site:

• Base station - DECT provides 11 RF channels of 1.8 GHz, DECT standard, used in Europe, Australia and South America.

• Base station - USA DECT provides 11 RF channels of the 1.9 GHz, USA DECT standard, used in North America.

KIRK Base Station Types and Part Numbers

The base station contain RF circuitry that comply with the local band standards: UPCS, DECT, or ETSI DECT. The table below includes a list of available base stations and their part numbers.

Table 6-1 KIRK Base Station Part Numbers

Variants of KIRK Base Stations Part Number

KIRK Base Station 12 1.8 GHz (conforms with standard DECT markets)

KIRK Base Station 12 1.9 GHz (for North America) 02337301

KIRK Base Station Appearance and Components

The base station front cover includes the following:

• LED that indicates the operating status of the unit

Figure 6-1 Base Station - Front view

02337300

6–2

Installing KIRK Base Station

ETH Port (Power supply by PoE)

LINK/Activity Indicator

Reset Button

The base station faceplate includes the following (see figure below).

Figure 6-2 Base Station - Faceplate

For information about the Reset button, refer to “Resetting the KIRK Base

Station Hardware” on page 6-5.

6–3

KIRK Wireless Server 6000 Installation and Configuration Guide

KIRK Base Station LED Indicators

Front Cover

The base station front cover has one indicator describing the base station faults and failures. The indicator is off when the base station is not powered. The LED flashes when the base station initializes. The indicator is on when the base station is operating.

Table 6-2 LED Indicator Description - Front Cover

LED Indicator Meaning

Steady green OK and idle

Slow green flashing OK and active voice call

Fast green flashing Active, in operation with the

Slow red flashing Missing media resource or base

maximum active connections (busy)

station (if it is a media resource: missing connection to KWS6000)

Fast red flashing Error

Steady red Reset/shutdown in progress

Steady red for 5 seconds followed by fast red flashing

Reset to factory settings

Faceplate

Figure 6-3 LED Indicator Description - Faceplate

LED Indicator Meaning

LINK/Activity Indicator - green Link layer software has

established connection

LINK/Activity Indicator - green flashing

Power Indicator - green KWS6000 is connected to Power

Activity

6–4

KIRK Base Station - Reset Button

It is possible to restart or reset the base station by pressing the Reset button on the faceplate of the base station. For description of the faceplate, refer to

“Faceplate” on page 6-4.

Resetting the KIRK Base Station Hardware

This section contains a description of the different actions that take place when pressing the Reset button.

Table 6-3 Reset Button Description

Press button Action

Short press (2 to 5 sec.) System restarts when button is

Installing KIRK Base Station

released.

Long press (5 to 9 sec.) until front LED flashes red, then release button

Resets the system to factory default settings (original IP settings and empty user data base) and restarts the system.

Firmware version is not affected.

Installing the KIRK Base Station

The base station is suitable for mounting indoors on a wall.

Note

Wall Mounted (Vertical) Installation RF Coverage

Before beginning the installation, determine the position of the base station for best coverage. The coverage depends on the construction of the building, architecture, and the choice of building materials. Refer to

“Environmental Requirements”

on page 2-8 for more information about

environmental requirements for base stations.

For best RF coverage, the base station must be mounted vertically on walls. The antennas must always be kept perpendicular to the floor.

Caution:

The base station must not be installed at any angle other than vertical. If the base station is placed upside-down, the coverage area of the base station is decreased by 40 - 50% and it might not transmit or receive effectively.

6–5

KIRK Wireless Server 6000 Installation and Configuration Guide

Caution:

Do not mount the base station on soft surfaced walls such as those covered with canvas, metal or sponge-like materials.

1 Mount the base station on the wall using the anchors and screws

accompanying the product.

Note: When you place the base station on the screws, ensure that the screws do not touch the printed circuit board.

Figure 6-4 Base Station Wall Mounting

2 Connect the RJ45 plug to the ethernet connector at the bottom of the base

station.

Figure 6-5 Base Station - Ethernet Connector

Recording the Installation Information

After completing the installation of the base stations, record the location of each base station and add a descriptive text in the Administration Page of the KWS6000 under Administration/Base stations.

6–6

Installing KIRK Repeater

This section provides information about the repeater and how to unpack and install it. Installing repeaters requires a software installation as well as a hardware installation.

Before you install the equipment, ensure that a site planner defines the location of the repeaters.

This section includes information about:

• “KIRK Repeater Description” on page 6-1

• “Installing the KIRK Repeater” on page 6-4

• “Recording the Installation Information” on page 6-7

• “Checking Indicators” on page 6-7

• “Powering the KIRK Repeater” on page 6-7

• “Programming a KIRK Repeater with the KIRK Programming Kit” on

page 6-7

KIRK Repeater Description

This section contains information about:

• “KIRK Repeater provides RF Channels to KIRK Handsets” on page 6-1

• “KIRK Repeater Types and Part Numbers” on page 6-2

• “KIRK Repeater - Appearance and Components” on page 6-3

• “KIRK Repeater LED Indicators” on page 6-4

KIRK Repeater provides RF Channels to KIRK Handsets

The KIRK Repeater is a building block to be used to extend the coverage area in a KIRK solution. The repeater does not increase the number of traffic channels, however it provides a larger physical spreading of the traffic channels and thereby increases the coverage area established with the KIRK

6–1

KIRK Wireless Server 6000 Installation and Configuration Guide

Base Stations.The repeaters are mainly used in areas with limited traffic. The KIRK Repeater is available with either 2 or 4 voice channels. It is wireless and does not need physical connection to the KIRK Wireless Server, making it very easy to install. The repeaters can be supplied with an external antenna making it possible to create radio coverage in a remote area without cabling to the rest of the installation.

Note

The repeater is also termed by some manufacturers as the WRFP (Wireless Radio Fixed Part).

The RF communication is provided according to the band standard at the site:

• Repeater - DECT provides four RF channels of 1.88 GHz, DECT standard, used in Europe, Australia and South America.

• Repeater - USA DECT provides four RF channels of 1.9 GHz, USA DECT standard, used in North America.

KIRK Repeater Types and Part Numbers

The repeater contains RF circuitry that comply with the local band standards: UPCS, DECT, or ETSI DECT. The wall mounted repeater and the ceiling mounted repeater is available as a full slot repeater. A full slot repeater covers four simultaneous speech channels. These channels are borrowed from the attached base station, and are not additional channels to the total number of channels on the system.

The table below includes a list of available repeaters and their part numbers.

Table 6-1 KIRK Repeater - Wall - Part Number

6–2

Variants of KIRK Repeaters Part Number

KIRK Repeater 1.8 GHz, 2 channels

(Supported on KWS500, KWS600 and KWS600v3 single cell).

KIRK Repeater Residential 1.8 GHz, 4 channels

(Supported on KWS500, KWS600 and KWS600v3 single cell).

KIRK Repeater Business 1.8 GHz, 4 channels

(Supported on KWS300, KWS500, KWS600, KWS600v3 single and multi cell, KWS1500, KWS3000 and KWS6000).

KIRK Repeater Business 1.9 GHz, 4 channels

(Supported on KWS300, KWS500, KWS600, KWS600v3 single and multi cell, KWS1500, KWS3000 and KWS6000).

0244 0300

0233 4600

0233 4601

0233 8200

Installing KIRK Repeater

Table 6-1 KIRK Repeater - Wall - Part Number

Variants of KIRK Repeaters Part Number

KIRK Repeater with external antenna 1.8 GHz, 2 channels

(Supported on KWS300, KWS500, KWS600, KWS600v3 single and multi cell, KWS1500, KWS3000 and KWS6000).

KIRK Repeater with external antenna 1.8 GHz, 4 channels

(Supported on KWS300, KWS500, KWS600, KWS600v3 single and multi cell, KWS1500, KWS3000 and KWS6000).

KIRK Repeater with external antenna 1.9 GHz, 4 channels

(Supported on KWS300, KWS500, KWS600, KWS600v3 single and multi cell, KWS1500, KWS3000 and KWS6000).

KIRK Repeater - Appearance and Components

The repeater connection panel includes the following:

• Power supply connection (connection for programming the repeater as well).

Note: The power supply for the repeater is to be ordered separately (Part no. UK version: 84642421, Part no. EU version: 84642420, Part no. US version: 84642432).

0244 0000

0244 1600

0244 0200

• Antenna connector for repeaters supplied with external antenna connection.

Note: The external antenna incl. antenna cable is to be ordered separately (part no. 02319505).

• LED that indicates whether or not the unit is functioning.

6–3

KIRK Wireless Server 6000 Installation and Configuration Guide

LED

Figure 6-1 Repeater

KIRK Repeater LED Indicators

The repeater has one LED indicator describing the repeater operations: The indicator is off when the repeater is not powered. When the LED flashes after the repeater has been powered, sync has still not been established. As soon as sync has been established the LED is on. Each time a handset connects to the repeater, the LED flashes shortly. Each time a handset makes handover to a repeater, the LED flashes shortly.

Installing the KIRK Repeater

Before beginning the installation, determine the position of the repeater for best coverage. The coverage depends on the construction of the building, architecture, and the choice of building materials.

6–4

Installing KIRK Repeater

Environmental requirements

• Avoid installing repeaters on large concrete or marble columns because these columns affect radio coverage. If possible, place the base station a minimum of one meter/3.3 feet from these types of columns.

• Do not install a repeater with the antenna housings near metal objects. Be careful not to damage existing wiring or panels.

• Do not position repeaters in ducts, plenums or hollow spaces used to transport environmental air except where the duct, plenum or hollow space is created by a suspended ceiling having lay-in panels.

• Keep the repeater away from steel constructions.

• Do not position repeaters directly on metallic surfaces. If possible, place

the base station a minimum of one meter/3.3 feet from these types of surfaces.

• Do not position repeaters behind furniture.

• Only position repeaters where the signal is needed.

• The installation area must be clean, free of traffic and excess dust, dry, and

well ventilated.

Note

Caution

• The installation area must be within the temperature ranges of 10°C and 40°C/50°F and 104°F.

• The installation area must be between 20% and 80% non-condensing relative humidity.

The repeater does not add channels, it only adds additional coverage area.

The repeater can be registered on the system 1) when placed within the coverage area of a base station 2) when placed within the coverage area of an already-installed repeater or 3) when placed outside the coverage area using an external antenna.

For best RF coverage, the repeater must be mounted vertically on walls. The antennas must always be kept perpendicular to the floor.

The repeater must not be installed at any angle other than vertical. If the repeater is placed upside-down, the coverage area of the repeater is decreased by 40 - 50% and it might not transmit or receive effectively.

6–5

KIRK Wireless Server 6000 Installation and Configuration Guide

RepeaterExternal Antenna Only for repeaters supplied with external antenna connection)

Figure 6-2 Connect Power to the Bottom of the Repeater and External Antenna

Cable to the Rear of the Repeater

Holes for

wall

mounted

screws

External

antenna

cable (only

for repeaters

supplied

with

external

antenna

connection

Power

supply

cable

1 Connect the power supply cable into the RJ11 connector in the bottom of

the repeater. For repeaters with external antenna, connect the external antenna cable to the antenna connector in the rear of the repeater as well.

2 Mount the repeater onto the wall using the screws accompanying the

repeater.

Figure 6-3 Repeater and External Antenna Installed on the Wall

6–6

Note: The external antenna used for the transmitter is to be fixed-mounted on indoor permanent structures providing a separation distance of at least 20 cm / 8 inches from all persons during normal operation and must not be co-located or operating in conjunction with any other antenna or transmitter. The maximum radiated output power is 1W e.i.r.p. For more information and technical support, please refer to www.polycom.com.

Recording the Installation Information

After completing the installation of the repeaters, record the location of each repeater.

Checking Indicators

Verify that the repeater LED indicator is continuously on, indicating that the repeater is functional.

Installing KIRK Repeater

Powering the KIRK Repeater

Power Options

The power supply for the repeater is 9VDC, 300mA.

Programming a KIRK Repeater with the KIRK Programming Kit

This section provides information about:

• “Content of the KIRK Programming Kit Repeater” on page 6-7

• “Set up of the Hardware for Repeater Programming” on page 6-8

• “Programming the KIRK Repeater with the ServiceTool” on page 6-9

Content of the KIRK Programming Kit Repeater

The Programming Kit Repeater (Part no. 02319508) consists of:

6–7

KIRK Wireless Server 6000 Installation and Configuration Guide

Splitter

Serial cable

• splitter

• serial cable

Note

For programming the repeater you also need the programming software (ServiceTool) and the power supply for the repeater. The ServiceTool is not part of the Programming Kit Repeater but can be downloaded from www.polycom.com. The power supply for the repeater is to be ordered separately (Part no. UK version: 84642421, Part no. EU version: 84642420, Part no. US version: 84642432).

Figure 6-4 Programming Kit Repeater

Set up of the Hardware for Repeater Programming

1 Unplug the repeater power supply and insert the splitter. 2 Connect the repeater power supply to the splitter and the mains. LED

3 Connect the serial cable to the splitter and Com port of your computer.

6–8

flashes.

Note: Ensure that you have the appropriate power supply for the local requirements.

The repeater is now ready for programming via the ServiceTool.

Note: The above mentioned order of the set up (point 1, 2 and 3) is important.

Programming the KIRK Repeater with the ServiceTool

The ServiceTool is the tool you access from your desktop and use for repeater programming, handset adjustment and software download to the handset and repeater.

The ServiceTool identifies the type of repeater, and with this software it is possible to program the KIRK Repeater to connect to the KIRK DECT Radio Infrastructure solutions.

Before you start programming the repeater, ensure that the repeater is connected to the computer and the mains.

In a single cell solution the numbers assigned to the repeaters must be between 2 and 7. The number of the base station is default set to 1.

In a multi cell solution, the numbering of the base stations and repeaters has to follow the numbering in the table below.

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

0 64 128 192

1 65 129 193

2 66 130 194

3 67 131 195

4 68 132 196

5 69 133 197

6 70 134 198

7 71 135 199

8 72 136 200

9 73 137 201

10 74 138 202

11 75 139 203

12 76 140 204

13 77 141 205

14 78 142 206

15 79 143 207

16 80 144 208

17 81 145 209

18 82 146 210

19 83 147 211

20 84 148 212

21 85 149 213

Installing KIRK Repeater

6–9

KIRK Wireless Server 6000 Installation and Configuration Guide

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

22 86 150 214

23 87 151 215

24 88 152 216

25 89 153 217

26 90 154 218

27 91 155 219

28 92 156 220

29 93 157 221

30 94 158 222

31 95 159 223

32 96 160 224

33 97 161 225

34 98 162 226

35 99 163 227

36 100 164 228

37 101 165 229

38 102 166 230

39 103 167 231

40 104 168 232

41 105 169 233

42 106 170 234

43 107 171 235

44 108 172 236

45 109 173 237

46 110 174 238

47 111 175 239

48 112 176 240

49 113 177 241

50 114 178 242

51 115 179 243

52 116 180 244

53 117 181 245

54 118 182 246

55 119 183 247

56 120 184 248

6–10

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

57 121 185 249

58 122 186 250

59 123 187 251

60 124 188 252

61 125 189 253

62 126 190 254

63 127 191 255

64 128 192 0

65 129 193 1

66 130 194 2

67 131 195 3

68 132 196 4

69 133 197 5

70 134 198 6

71 135 199 7

72 136 200 8

73 137 201 9

74 138 202 10

75 139 203 11

76 140 204 12

77 141 205 13

78 142 206 14

79 143 207 15

80 144 208 16

81 145 209 17

82 146 210 18

83 147 211 19

84 148 212 20

85 149 213 21

86 150 214 22

87 151 215 23

88 152 216 24

89 153 217 25

90 154 218 26

91 155 219 27

Installing KIRK Repeater

6–11

KIRK Wireless Server 6000 Installation and Configuration Guide

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

92 156 220 28

93 157 221 29

94 158 222 30

95 159 223 31

96 160 224 32

97 161 225 33

98 162 226 34

99 163 227 35

100 164 228 36

101 165 229 37

102 166 230 38

103 167 231 39

104 168 232 40

105 169 233 41

106 170 234 42

107 171 235 43

108 172 236 44

109 173 237 45

110 174 238 46

111 175 239 47

112 176 240 48

113 177 241 49

114 178 242 50

115 179 243 51

116 180 244 52

117 181 245 53

118 182 246 54

119 183 247 55

120 184 248 56

121 185 249 57

122 186 250 58

123 187 251 59

124 188 252 60

125 189 253 61

126 190 254 62

6–12

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

127 191 255 63

128 192 0 64

129 193 1 65

130 194 2 66

131 195 3 67

132 196 4 68

133 197 5 69

134 198 6 70

135 199 7 71

136 200 8 72

137 201 9 73

138 202 10 74

139 203 11 75

140 204 12 76

141 205 13 77

142 206 14 78

143 207 15 79

144 208 16 80

145 209 17 81

146 210 18 82

147 211 19 83

148 212 20 84

149 213 21 85

150 214 22 86

151 215 23 87

152 216 24 88

153 217 25 89

154 218 26 90

155 219 27 91

156 220 28 92

157 221 29 93

158 222 30 94

159 223 31 95

160 224 32 96

161 225 33 97

Installing KIRK Repeater

6–13

KIRK Wireless Server 6000 Installation and Configuration Guide

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

162 226 34 98

163 227 35 99

164 228 36 100

165 229 37 101

166 230 38 102

167 231 39 103

168 232 40 104

169 233 41 105

170 234 42 106

171 235 43 107

172 236 44 108

173 237 45 109

174 238 46 110

175 239 47 111

176 240 48 112

177 241 49 113

178 242 50 114

179 243 51 115

180 244 52 116

181 245 53 117

182 246 54 118

183 247 55 119

184 248 56 120

185 249 57 121

186 250 58 122

187 251 59 123

188 252 60 124

189 253 61 125

190 254 62 126

191 255 63 127

192 0 64 128

193 1 65 129

194 2 66 130

195 3 67 131

196 4 68 132

6–14

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

197 5 69 133

198 6 70 134

199 7 71 135

200 8 72 136

201 9 73 137

202 10 74 138

203 11 75 139

204 12 76 140

205 13 77 141

206 14 78 142

207 15 79 143

208 16 80 144

209 17 81 145

210 18 82 146

211 19 83 147

212 20 84 148

213 21 85 149

214 22 86 150

215 23 87 151

216 24 88 152

217 25 89 153

218 26 90 154

219 27 91 155

220 28 92 156

221 29 93 157

222 30 94 158

223 31 95 159

224 32 96 160

225 33 97 161

226 34 98 162

227 35 99 163

228 36 100 164

229 37 101 165

230 38 102 166

231 39 103 167

Installing KIRK Repeater

6–15

KIRK Wireless Server 6000 Installation and Configuration Guide

Table 6-2 Repeater Numbering in a Multi Cell Solution

Base Station Repeater 1 Repeater 2 Repeater 3

232 40 104 168

233 41 105 169

234 42 106 170

235 43 107 171

236 44 108 172

237 45 109 173

238 46 110 174

239 47 111 175

240 48 112 176

241 49 113 177

242 50 114 178

243 51 115 179

244 52 116 180

245 53 117 181

246 54 118 182

247 55 119 183

248 56 120 184

249 57 121 185

250 58 122 186

251 59 123 187

252 60 124 188

253 61 125 189

254 62 126 190

255 63 127 191

Note

Repeater and base station numbers must not be the same. Neither can the repeater have a number similar to another base station or another repeater in a situation where common overlap is present between the actual units (Numbers with red colour show where numbering could be identical between different units). If this occurs, handover between the different units is not possible.

6–16

Installing KIRK Repeater

Table 6-3 Example of a Normal Base Station/Repeater Configuration

Numbering of base stations and repeaters in a normal configuration

First repeater No. of base station + 64

Base to synchronize on: Number of base station

Second repeater No. of base station + 128

Base to synchronize on: Number of base station

Third repeater No. of base station + 192

Base to synchronize on: Number of base station

Table 6-4 Example of Repeater Jump Configuration

Numbering of repeaters in a repeater jump configuration

First repeater in chain No. of base station + 64

Base to synchronize on: Number of base station

Second repeater in chain No. of base station + 128

Base to synchronize on: Number of previous repeater

Third repeater in chain No. of base station + 192

Base to synchronize on: Number of previous repeater

For more information about programming the repeater with the ServiceTool, refer to the Help File in the ServiceTool. The ServiceTool is to be downloaded from www.polycom.com.

6–17

KIRK Wireless Server 6000 Installation and Configuration Guide

Base Station

Radio Link

Use of KIRK Repeaters without External Antenna

Use of KIRK Repeater with external Antenna

Use of KIRK Repeater With External Antenna

If radio coverage between a base station and a repeater is not needed, it is possible to synchronize between the radio units using a repeater with external antenna.

Figure 6-5 Use of Repeaters

Synchronization Ways

The distance from the repeaters without external antenna to the base station must correspond to a RSSI loss of maximum 25dB.

Be aware that inside the area named “radio link” there is no radio coverage, and therefore a wireless handset cannot be used in this area.

The distance between the base station and the repeater with external antenna depends on the type of antenna used as well as on the signal attenuation created by surroundings such as buildings, trees, etc.

The repeater with external antenna, 4 channels, can be programmed to obtain synchronization on two radio units (base station, wireless server or repeater).

If a situation occurs where the primary sync for some reason breaks down, the repeater will obtain sync on the alternative sync.

Be aware that the primary sync has priority; the alternative sync is only in use as long as the primary sync is down.

6–18

Preparing KIRK Handset for Use

This section provides information about how to prepare the handset for use, to install and charge the battery and how to retrieve the serial numbers on the different handsets.

This section includes information about:

• “KIRK Handset Description” on page 8-1

• “Installing Battery” on page 8-4

• “Charging KIRK Handsets” on page 8-7

• “Retrieving the Serial Number of the KIRK Handset” on page 8-12

Note

For more information on the different handsets, refer to the handset user guides.

The charger and the power supply for the charger are to be ordered separately (refer to “KIRK Charger Types and Part Numbers” on page 8-2 and “Power Supply Types and Part Numbers” on page 8-3 for information on part numbers).

KIRK Handset Description

The handset is a lightweight, ergonomically designed wireless unit that includes and LCD display and keyboard.

8–1

KIRK Wireless Server 6000 Installation and Configuration Guide

KIRK Handset Types and Part Numbers

Table 8-1 Variants of KIRK Handsets

Variants of KIRK Handsets

Handset sets from one of the following categories (including batteries):

KIRK 4020 Handset

KIRK 4040 Handset

KIRK 4080 Handset

KIRK 5020 Handset

KIRK 5040 Handset

KIRK 6020 Handset

KIRK 6040 Handset

KIRK 7010 Handset

KIRK 7020 Handset

KIRK 7040 Handset

KIRK Charger Types and Part Numbers

Table 8-2 Variants of KIRK Charger

Variants of KIRK Chargers

KIRK Single Charger (For KIRK 4020 and KIRK 4040)

(Part no. 84642450) (EU, UK)

(Part no. 84642462) (US)

KIRK Single Charger (For KIRK 4080)

(Part no. 84642458) (EU, UK)

KIRK Single Charger - Ordinary (For KIRK 5020/5040)

(Part no. 84642464) (countries outside US)

(Part no. 84642472) (US)

8–2

Table 8-2 Variants of KIRK Charger

Variants of KIRK Chargers

KIRK Single Charger - USB (For KIRK 5020/5040)

(Part no. 84642466) (countries outside US)

(Part no. 84642473) (US)

USB cable (Part no. 84718504)

kIRK Single Charger - Ordinary (For KIRK 6020/6040) (Part no. 84642488) (countries outside US)

USB cable (Part no. 84642489)

KIRK Single Charger - Ordinary (For KIRK 7010/20/40)

(Part no. 84642493) (countries outside US)

USB cable (Part no. 84642494)

Power Supply Types and Part Numbers

Preparing KIRK Handset for Use

Table 8-3 Variants of Power Supplies

Variants of Power Supplies

Power Supply (For KIRK 4020, 4040 and 4080)

(Part no. 84642420) (EU)

(Part no. 84642421) (UK)

(Part no. 84642432) (US)

Power Supply for KIRK Multicharger (For KIRK 4020 and KIRK 4040)

(Part no. 84642439) (EU, UK)

Power Supply (For KIRK 5020(/5040)

(Part no. 84642481) (EU)

(Part no. 84642470) (UK)

(Part no. 84642471) (US)

Power Supply (For KIRK 6020/6040/7010/7020/7040) (Part no. 84642481) (EU)

(Part no. 84642470) (UK)

8–3

KIRK Wireless Server 6000 Installation and Configuration Guide

Installing Battery

Read the following information before you handle the batteries:

• Do not replace the batteries in potentially explosive environments, such as rooms where flammable liquids or gases are present.

• The battery will explode if disposed of in a fire.

• Do not charge the batteries unless you use the approved charger and the

proper batteries.

• Only use battery type 84743411 in the 3040 Handset, 4020 Handset and 4040 Handset. Do not use these batteries with other products. These batteries were designed specifically for use with the 3040 Handset, 4020 Handset and 4040 Handset and the charger ONLY. Improper use of the batteries may result in fire hazard.

• Only use battery type 84743416 in the 4080 Handset. Do not use this battery with other products. This battery was designed specifically for use with the 4080 Handset and the charger ONLY. Improper use of the battery may result in fire hazard.

• Only use battery type 84743418 (ICP73048) in the 5020 Handset. Do not use this battery with other products. This battery was designed specifically for use with the 5020 Handset and the charger ONLY. Improper use of the battery may result in fire hazard.

• Do not do anything that would cause the battery to short circuit.

• Do not let the battery or the charger come into contact with conductive

metal objects.

8–4

Installing Battery on KIRK 3040 Handsets

This section describes how to install the battery on a 3040 Handset.

1 To install the battery press down the back cover and push it 5 mm

towards the headset plug.

Figure 8-1 Remove Back Cover from Handset

2 Lift off back cover. 3 Place the battery plug in the slot in the battery box.

Preparing KIRK Handset for Use

4 Insert battery with the label readable. 5 Replace the back cover.

Installing Battery on KIRK 4020/KIRK 4040/KIRK 4080 Handsets

Note

Warning

The battery is connected to the handset when it is shipped from the factory.

The battery in a 4080 Handset must not be removed in a potentially explosive atmosphere. Only use battery type 84743416 in the 4080 Handset.

8–5

KIRK Wireless Server 6000 Installation and Configuration Guide

This section describes how to install the battery on a 4020/4040/4080 Handset.

1 To change the battery unscrew the plate on the rear of the handset to

access the battery compartment. Use a normal screw driver.

2 Insert the screwdriver into the small crack behind the blind cover and

break to open the handset.

Figure 8-2 Remove Back Cover from Handset with Screw Fastener

3 Place the battery plug in the slot in the battery box. 4 Insert battery with the label readable. 5 Replace the back cover.

Installing Battery on KIRK 5020 and KIRK 5040 Handsets

This section describes how to install the battery on a 5020 Handset.

1 To install the battery press down the back cover and slide it towards the

bottom of the handset.

Figure 8-3 Remove Back Cover from Handset

2 Lift off back cover.

8–6

3 Insert battery with the label readable. 4 Replace the back cover by pressing the back cover back in the locked

position (when you hear a click the back cover is in position).

Charging KIRK Handsets

Using the Charger

Each handset is charged through the use of a handset charger, a compact desktop unit designed to charge and automatically maintain the correct battery charge levels and voltage.

The charger for the 3040/4020/4040/4080 Handset is powered by an AC (115VAC or 230VAC) adapter that supplies the 9VDC at 230mA charger requirement.

The charger for the 5020 Handset is powered by an AC (110VAC to 240VAC) adapter that supplies the 8VDC at 350mA charger requirement.

Preparing KIRK Handset for Use

Figure 8-4 Single Charger for 3040 Handset

8–7

KIRK Wireless Server 6000 Installation and Configuration Guide

Figure 8-5 Single Charger for 4020 Handset and 4040 Handset

Figure 8-6 Single Charger for 4080 Handset

8–8

Figure 8-7 Multicharger for 4020 Handset and 4040 Handset

Figure 8-8 Single Charger for 5020 Handset

Figure 8-9 Single Charger for 5040 Handset

Preparing KIRK Handset for Use

Charging Battery

Warning

Note

KIRK 3040/KIRK 4020/KIRK 4040 and KIRK 4080 Handsets

When charging the battery for the first time, it is necessary to leave the handset in the charger for 14 - 16 hours before the battery is fully charged and the handset ready for use.

Do not charge 4080 Handset in a potentially explosive atmostphere. Use only the dedicated charger (orange) for charging of 4080 Handset.

During normal operation, it takes approximately 3 1/2 hours to charge the handset from fully discharged to its full capacity.

8–9

KIRK Wireless Server 6000 Installation and Configuration Guide

• Place the handset in the charger.

For correct charging, be sure the room temperature is between 0°C and 25°C/32°F and 77°F. Do not place the handset in direct sunlight. The battery has a built-in heat sensor which will stop charging if the battery temperature is too high.

If the handset is turned off when placed in charger, only the LED indicates the charging. When handset is turned off, the LED flashes at a low frequency while charging and lights constantly when the charging is finished. There will be no reaction for incoming calls.

If the handset is turned on when charging, the display shows the charging status. It will not vibrate. B-answer is inactive. The handset reacts normally for incoming calls. The display goes back to normal mode when fully charged.

It is necessary to recharge the battery when the display shows BATTERY LOW, or if the handset cannot be turned on. When the battery is fully discharged, up to 10 minutes may pass before charging begins (display lights up). When the charger begins the charging, status is shown on the display if the handset is turned on.

The handset displays a progress indicator bar that shows how fully charged the battery is.

Note

The handset LED gives the following indication:

• LED continuously on - handset is fully charged

• LED flashing - handset is charging

KIRK 5020/5040 Handsets

When charging the battery for the first time, it is necessary to leave the handset in the charger for 14 - 16 hours before the battery is fully charged and the handset ready for use.

During normal operation, it takes approximately four hours to charge the handset from fully discharged to its full capacity.

• Place the handset in the charger.

For correct charging, be sure the room temperature is between 0°C and 40°C/32°F and 104°F. Do not place the handset in direct sunlight. The battery has a built-in heat sensor which will stop charging if the battery temperature is too high.

If the handset is turned off when placed in charger, nothing indicates the charging. There will be no reaction for incoming calls.

8–10

Preparing KIRK Handset for Use

If the handset is turned on when charging, the display shows a blue charging icon. The charging icon turns green when fully charged (when handset is removed from charger, the charging icon disappears). It will not vibrate. B-answer is inactive. The handset reacts normally for incoming calls.

It is necessary to recharge the battery when the handset display shows the battery low icon, or if the handset cannot be turned on.

8–11

KIRK Wireless Server 6000 Installation and Configuration Guide

Retrieving the Serial Number of the KIRK Handset

To enable service to the handset, the serial number must be programmed into the system database via the web based Administration Page of the KWS6000. (For more information, refer to “Registering KIRK Handsets” on page 13-1).

The serial number (IPEI number) of each handset is found either on a label, which is placed behind the battery, or on the packaging label.

To show the serial number on the handset display (3040 Handset/4020 Handset/4040 and 4080 Handset), press *99984*, and then press number appears on the handset display. Press < for 5 seconds to exit the menu.

To show the serial number on the handset display (5020/5040 Handset), press Menu, select Status and then select Firmware version. Press exit to exit the menu.

Retrieving Serial Number on KIRK 3040 Handsets

This section describes how to retrieve the serial number on a 3040 Handset.

3; the serial

Note

1 Press down the back cover and push it 5 mm towards the headset plug.

Figure 8-10 Remove Back Cover from Handset

2 Lift off back cover. 3 Lift the battery and read the serial number. 4 Replace battery and back cover.

To show the serial number on the handset display, press *99984*, and then

3; the serial number appears on the handset display. Press < for 5

press seconds to exit the menu.

8–12

Preparing KIRK Handset for Use

Retrieving Serial Number on KIRK 4020/KIRK 4040/KIRK 4080 Handsets

This section describes how to retrieve the serial number on a 4020/4040/4080 Handset.

1 Use a screwdriver to unscrew the plate on the rear of the handset to

access the battery compartment.

2 The plate on the rear of the 4080 Handset must not be removed in a

potentially explosive atmostphere.

3 Insert the screwdriver into the small crack behind the blind cover and

press to open the handset.

Figure 8-11 Remove Back Cover from Handset with Screw Fastener

Note

4 Lift the battery and read the serial number. 5 Replace battery and back cover.

To show the serial number on the handset display, press *99984*, and then

3; the serial number appears on the handset display. Press < for 5

press seconds to exit the menu.

8–13

KIRK Wireless Server 6000 Installation and Configuration Guide

Retrieving Serial Number on KIRK 5020/5040 Handsets

This section describes how to retrieve the serial number on a 5020 Handset.

1 Press down the back cover and slide it towards the bottom of the handset.

Figure 8-12 Remove Back Cover from Handset

2 Lift off back cover. 3 Lift the battery and read the serial number. 4 Replace battery and back cover.

Note

To show the serial number on the handset display (5020 Handset), press Menu,

select Status and then select Firmware version. Press exit to exit the menu.

8–14

Basic Network Configuration

This section provides you with information on basic network configuration. Basic network settings can be derived from a DHCP server or entered manually through TCP/IP Setup.

Using DHCP the device requests and obtains an available IP address from a DHCP server. The device also obtains other parameters such as the default gateway, subnet mask, DNS server, Time server and other IP parameters from the DHCP server.

Using manual TCP/IP Setup the IP addresses and other networking parameters are entered manually through the web based Administration Page. The static IP addresses are unique, provided and managed by your system administrator.

This section contains information about:

• “Recommended Network Configuration” on page 9-1

• “Assigning DHCP Server Options” on page 9-2

• “Assigning DHCP Server Reservations” on page 9-2

Recommended Network Configuration

When configuring a KWS6000 Solution, it is strongly recommended to configure:

• KWS6000 using static IP address

• Media resources using DHCP

• Base stations using DHCP

Note

When using DHCP on base stations and media resources, the KWS6000 must have either a static IP address or IP address reservations assigned to the DHCP server.

9–1

KIRK Wireless Server 6000 Installation and Configuration Guide

If the KWS6000 Solution is configured as recommended above, it is possible to assign options to the DHCP server making it extremely easy to configure all media resources and base stations. For more information about assigning options to the DHCP server, refer to “Assigning DHCP Server Options” on page 9-2.

If the KWS6000 is configured using DHCP, it is necessary to assign a reservation for the device on the DHCP server. For more information about assigning reservations to the DHCP server, refer to “Assigning DHCP Server

Reservations” on page 9-2.

Assigning DHCP Server Options

You can provide information about the static IP address of the KWS6000 in the DHCP server through DHCP options. When defining the IP address of the KWS6000 in the DHCP server, all media resources and base stations are configured automatically.

Below you will find a description of how to assign options to a DHCP server when opening a DHCP server console (MS 2000/2003 DHCP Server):

• When adding a new class you must enter the following information:

— Display name: KIRK IP6000

— Description: KIRK Wireless Server 6000 Solution

— ASCII: KIRK.IP6000 (case sensitive)

• When adding a new option you must enter the following information:

— Name: KWS6000

— Type: String

— Code: 43

• Select options 43.

• Enter the IP address of the KIRK Wireless Server 6000.

Assigning DHCP Server Reservations

If the KWS6000 is configured using DHCP, it is necessary to assign a reservation for the device on the DHCP server.

9–2

Configuring KIRK W ireless Server 6000

This section provides you with information on how to power up the KWS6000 and connect the unit to a computer. It also provides information on how to configure a KWS6000 through the web based Administration Page using either DHCP or static IP address.

Note

The KWS6000 is pre-configured to use a static IP address.

This section includes information about:

• “Powering up the KWS6000 Server and Media Resource” on page 10-1

• “Connecting a Computer to the KWS6000” on page 10-2

• “Accessing the Web Based Administration Page” on page 10-3

• “Configuring a KIRK Wireless Server 6000 Using Static IP Address” on

page 10-7

• “Configuring a KIRK Wireless Server 6000 Using DHCP” on page 10-13

• “Checking Indicators” on page 10-15

• “Making a Back-Up of the Configuration File” on page 10-15

Powering up the KWS6000 Server and Media Resource

After installing the KWS6000 server you need to power up the unit using:

• Power supply for KWS6000: 8VDC, 1 W maximum when using local power supply.

After installing the KWS6000 base station you need to power up the unit using:

• Power supply for KWS6000: 48VDC, 1 W maximum when using local

power supply.

10–1

KIRK Wireless Server 6000 Installation and Configuration Guide

Local Power Supply

Powering the KWS6000 with a local power supply can be done using the power input on the unit.

Note

The power supply for the KWS6000 is to be ordered separately (Part no. EU, UK and US version: 84642468).

Connecting a Computer to the KWS6000

The KWS6000 communicates with the computer through a cross-over patch cable.

Note

The LAN port of the KWS6000 is a RJ45 connector.

Figure 10-1 Cross-over patch cable (RJ45)

1 Connect the cross-over patch cable to the computer.

10–2

Configuring KIRK Wireless Server 6000

2 Connect the cross-over patch cable to the ETH port of the KWS6000.

Accessing the Web Based Administration Page

In order for your computer to communicate with the KWS6000 it is necessary to change the computer’s Internet Protocol Properties to use the following:

• IP address: 192.168.0.2

• Sub-net mask: 255.255.255.0

How to Change Internet Protocol Properties using Windows XP

1 From the Start menu, point to Connect to and then click Show all

connections.

A Network Connections window appears.

10–3

KIRK Wireless Server 6000 Installation and Configuration Guide

2 Under Lan or High-Speed Internet, right-click on Local Area

Connection and click Properties.

A Local Area Connection Properties dialog box appears.

Figure 10-2 Local Area Connection Properties dialog box

3 In the General tab, select Internet Protocol (TCP/IP), and then click

Properties.

An Internet Protocol (TCP/IP) Properties dialog box appears.

Figure 10-3 Internet Protocol Properties dialog box

10–4

4 Click Use the following IP address, and then type 192.168.0.2 in the IP

address field.

5 In the Subnet mask field, type 255.255.255.0. 6 Click OK.

You can now reach the KWS6000 using a standard web browser.

How to Access the Administration Page

The web based Administration Page is accessed through a standard web browser.

1 Open a web browser. 2 In the browsers Address bar, type http://192.168.0.1, and then press

ENTER.

The KWS6000 Administration Page appears.

Figure 10-4 Main page of the Administration Page for wireless server

Configuring KIRK Wireless Server 6000

10–5

KIRK Wireless Server 6000 Installation and Configuration Guide

Entering a System User Name and Password

First time you access the Administration Page, you need to log on with user name and a password.

Note

The default user name of the system is admin and the default password of the system is ip6000. It is strongly recommeded to change the password, refer to “Changing System User Name and Password”

Figure 10-5 Adm. Page: Enter Network Password dialog box

1 In the User Name field, type admin. 2 In the Password field, type ip6000. 3 Click OK.

on page 15-2.

10–6

Configuring KIRK Wireless Server 6000

Configuring a KIRK Wireless Server 6000 Using Static IP Address

This section describes how to configure a KWS6000 using static IP address.

Note

The KWS6000 is pre-configured to use a static IP address. It is strongly recommended to configure the KWS6000 using static IP address.

Figure 10-6 KWS6000 installation

For information on accessing the web based Administration Page, refer to

“Accessing the Web Based Administration Page” on page 10-3.

This section contains information about:

• “General Configuration” on page 10-8

• “Wireless Server Configuration” on page 10-9

• “Built-In Media Resource Configuration” on page 10-9

• “SIP Configuration” on page 10-10

• “Security Configuration” on page 10-12

10–7

KIRK Wireless Server 6000 Installation and Configuration Guide

General Configuration

On the Configuration/General page you define IP, DNS and NTP settings for the KWS6000.

1 Click Configuration, and then click General.

Figure 10-7 Adm. Page WS: Configuration/General page

2 Click Use Static IP Address. 3 In the IP Addr field, type the IP address of the KWS6000. 4 In the Netmask field, type a new network mask (optional).

Contact your system administrator for more information.

5 In the Gateway field, type the IP address of the default gateway

(optional).

The default gateway serves as an access point to another network.

Contact your system administrator for more information.

6 In the MTU field (Maximum Translation Unit), type the size of the largest

packet, that your network protocol can transmit (optional).

7 In the Domain field, type the domain name of the system (optional). 8 In the Server field (under DNS - Domain Name System), type the IP

address of the DNS server (optional).

9 In the Server field (under NTP - Network Time Protocol), type the IP

address of the NTP server from which the system will obtain the current time (optional).

10 From the Time Zone list, select the wanted time zone (optional). 11 Click Save to save your general configuration data.

10–8

Wireless Server Configuration

On the Configuration/Wireless Server page you configure the KWS6000 to allow subscription. If the system does not allow subscription, it is not possible to subscribe a handset.

1 Click Configuration, and then click Wireless Server.

2 Select the Subscription Allowed check box (optional).

Note: If not selected, you cannot subscribe a handset.

3 Click Save.

Built-In Media Resource Configuration

On the Configuration/Media Resource page you configure the built-in Media Resource.

Configuring KIRK Wireless Server 6000

1 Click Configuration, and then click Media Resource.

Figure 10-8 Adm. Page WS: Configuration/Media Resource page

2 In the Host field, type localhost if you want to activate the built-in media

resource.

3 Click Save.

10–9

KIRK Wireless Server 6000 Installation and Configuration Guide

SIP Configuration

On the Configuration/SIP page you define general SIP settings, information about authentication, DTMF signalling, message waiting indication and media.

1 Click Configuration, and then click SIP.

Figure 10-9 Adm. Page WS: Configuration/SIP page

2 In the Local Port field, type the local port number.

3 In the Default Domain field, type the name of the domain.

4 In the Proxy field, type a SIP proxy (optional).

10–10

The default local port number is 5060.

The local port is the port on which the KWS6000 listens for

Note:

incoming SIP-signalling.

Note:

If no user specific domain is configured, the handsets registered on

the KWS6000 will use the default domain as the domain part of the SIP URI; e.g. John Doe <sip:1234@somecompany.com>.

Note: The proxy is the SIP URI of the SIP-proxy. The KWS6000 will route all outgoing SIP signalling to the proxy, e.g. SIP registrations and outgoing calls.

Polycom KIRK 6000, KWS6000 Installation And Configuration Manual

Specifications and Main Features

Frequently Asked Questions

User Manual