Polycom 50” PDP DISPLAY Owner's Manual

OWNERS MANUAL

ユーザーマニュアル

사용 설명서

РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ

MANUAL DEL PROPIETARIO

使用手冊

用户手册

50” PDP DISPLAY

50” PDP DISPLAY

Table of Contents

1

2

3

4

5

02

Important Safety Instructions
Warnings & Precautions

Cleaning & Maintenance
Regulatory Notice

Overview
Checking the Accessories Supplied

Front Panel Controls
Battery Installation
Rear Panel Connections
Remote Control Buttons
Changing Inputs
Using the OSD Menu
On-Screen Display Status Display

Installation

Connecting POLYCOM Video Conferencing System
Connecting a VCR
Connecting a DVD
Connecting a Set-Top Box
Connecting an External Amplifiers
Connecting External Amplified Speaker
External Audio Connections
Connecting a PC

Menu System

Picture Adjustment
Fine Tune RGB Mode
Understanding Widescreen Modes
Adjusting Sound Setting
System Adjustment

Additional Information

Troubleshooting
Specification
RS-232 Connection/Command
Dimension Drawings
Color Scheme
Packing Break Out
Regulatory Label

3
4
5

6
6
6
7
8
9
9
9

10
10
10

11
12
12
12

15
16
17
17
18

19
20
24
26
26
27
28

12

3

6

10

15

19

Read and keep these instructions.
Follow all instructions.
Heed all warnings.
The unit should be operated from the type of power source indicated on the label. If the type of available
power is unknown, consult your dealer or local power company.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instruction.
Do not install near any heat sources such as radiators. Heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type. A polarized plug has two blades with
one wider than other. A grounding type plug has two blades and third grounding prong. The wide blade or
the third prong are provided for you safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged; liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture; does not operate normally; or
has been dropped.
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
Do not hit this panel . Be careful to prevent from getting hurt by broken glass pieces in case the panel breaks.
Be sure to install the display unit according to the installation instruction recommended by the manufacturer.
Upon completion if service or maintenance, request the service technician to perform safety check to ensure
that the display unit is in proper operating condition.

0 0

This display unit only operates within the temperature 0 C to 40 C. Operation outside of the recommendation
may cause damage to your product.

Certain programs may be copyrighted and unauthorized recording in whole or in part may be in violation
of copyright laws in the U.S. and Canada.
FCC/CSA regulations state that any unauthorized modifications to this display may void user authority to
operate it.

03

Important Safety Instructions

Special Notices

Warning & Precautions

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: To reduce the risk of electric shock, do not remove the front or back covers.
No user-serviceable parts inside. Refer servicing to qualified service personnel only.

The lightning flash with arrow-head
with in a triangle is intended to inform
the user that parts inside the product
are a risk of electric shock.

The exclamation point within a triangle
is intended to tell the user that important
operating and servicing instructions are
explained.

!

!

Important Safety Instructions

Disconnect the unit from the main supply and refer servicing to qualified service personnel
under the following conditions:
Power cord or plug is damages or frayed.
Liquid has been spilled into the product and/or the unit has been exposed to water
or moisture.
Unit does not operate normally when the operating instructions are not followed. Adjust
only those controls that are covered by the operating instructions, improper adjustment of
other controls may result in damage which often requires extensive work by a qualified
technician to restore the unit to normal operation.
Unit has been dropped or the cabinet has been damaged.
Unit exhibits a distinct change in performance, indicating a need for service.

Cleaning & Maintenance

Disconnect from the electric outlet before cleaning. Do not use liquid or aerosol cleaners.
Use only a slightly damp cloth for cleaning.

Regulatory Notice

CE Statement

The CE label on this product indicates that it complies with the 89/336/ EEC directive
on electromagnetic compatibility and safety rules as defined in the 73/23/EEC and 93/68/
EEC low voltage directives.
This Product is protected against interferences from other electronic devices, provided that
these devices comply with the standards in force. Sporadic interferences may happen
nevertheless.

FCC Statement

The Federal Communications Commission Radio Frequency Interference Statement includes
the following warming:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television receptions, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one ot more of the
following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/display technician for help.

04

05

Warning

User must use shielded signal interface cables to maintain FCC compliance for the product.
Provided with this display is a detachable power supply cord with IEC320 style terminations.
It may be suitable for connection to any UL Listed personal computer with similar
configuration.
Before making the connection, make sure the voltage rating of the computer convenience
outlet is the same as the monitor and that the ampere rating of the computer convenience
outlet is equal to or exceeds the monitor voltage rating. For 120 Volt supplications, use
only UL Listed detachable power cord with NEMA configuration 5-15 P TYPE
(parallel blades)plug cap.For 240 Volt applications use only UL Listed Detachable
power supply cord with NEMA configuration 6015p type(tandem blades) plug cap .

IC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian interference-Causing
Equipment Regulations of ICES-003.

ROHS Compliance Statement

This display defined in this owner manual is 100% ROHS compliant and meets all the
requirements set forth in European Union Directive 2002/95/EC, Restriction of the
Use of Certain Hazardous Substances in Electrical and Electronic Equipment.

Important Safety Instructions

Used electrical and electronic equipment must be treated separately and
in accordance with legislation that requires proper treatment, recovery
and recycling of used electrical and electronic equipment. When this
crossed- out wheeled bin symbol is attached to a product, it means the
product is covered by the European Directive 2002/979/EC.If you wish to
discard of this product, please contact your local authorities and ask the
correct method of disposal. The correct disposal of your old product will
help prevent potential negative consequences for the environment and
human health.
Attention: If you want to dispose of this equipment, please do not use the
ordinary dust bin!

Information on Disposal for Your Old Product

06

Overview

Checking the Accessories Supplied

PDP Display

Remote Control
with Batteries

User’s Manual

Front Panel Controls

Status LED
Orange-Standby
The LED will illuminate in orange color if
the display is at standby mode and the
main power cord is plugged into the back
of the unit.
Solid Green-Power on

Power(Standby) Button
Turns power on from standby mode.
There is a wait period between
on/standby cycles.

Volume Adjustment Buttons
Use these buttons to adjust volume up and
down. These keys also serve as an navigation
and adjustment keys when On Screen
Display menu is engaged.

Select Buttons
Use these buttons to navigate through the On
Screen Display menu.

Menu Button
Use this button to engage the On Screen
Display menu.

Input Button
Use this button to switch between available
inputs.

Battery Installation

1

1

3

3

2

4

4

5

5 2

6

6

07

Overview

Rear Panel Connections

1

RGB Input

Connect to RGB input of computer or Set-Top Box.

Component Video Input

Auto-detecting component video inputs (Y/Pb/Pr
or Y/Cb/Cr) for connecting to the component
output of video conferencing system, DVD player
or Set-Top Box.

Audio Output

Variable or fixed audio output jacks for connecting
to an external audio amplifier.

Composite/S-Video Input

Connect S-Video signals from external sources
such as VCRs, DVD players or camcorder.

RS-232 Connector

Connect to a computer serial port.

*HDMI, the HDMI logo and High-Definition Multimedia
Interface are trade marks or registered trademarks
of HDMI Licensing LLC

*USB port is provided for after service/engineer
use ONLY.

5

2

6

3

4

15 26 34

Connects to the digital video signals from

HDMI 1 /HDMI 2 Input

a Set-Top Box or PC video connector.

DVI is also supported through HDMI,
using a DVI to HDMI adapter cable.
DVI audio is supported using the DVI
audio input jacks.

Note:

Standby Power On/off

Push this button to turn on the display from Standby mode.
Push it again to Standby mode.

POLYCOM Mode

Pu sh this key to select POLYCOM mo des for
op timal con feren ce perfor mance.

Remote Control Buttons

08

1

2

Press Exit button to close the screen.On Screen Display menu

Number Keypad

These keys are not applicable for this display.

Quick View

This key is not applicable for this display.

Wide

Toggles between various aspect ratio settings.

Menu

Engages the On Screen Display menu.

VOL. / ADJ.

Turns volume up or down. (Only applicable if optional side
mounted or external amplified speakers are connected
directly to the display.)
Use ADJ. keys to scroll through the On Screen Display
menu.

3

4

5

6

7

SEL..

Use SEL. button up or down to
Screen Display menu.

navigate through the On

EXIT

Direct Input Selection Keys

Directly change input signal modes.

Input Select

Press to select input signal modes sequentially.

Sound Mute On/Off

To mute or restore the sound. (Only applicable if optional
side mounted or external amplified speaker are connected

directly to the display.)

Info.

Press to show the status of the display.

Q.Access

This key is not applicable for this display.

Sleep

Press this key to engage sleep timer selection directly.

Recall

Press this key to return to POLYCOM video mode settings for
optimal conference performance.

8

9

10

11

12

13

14

15

16

2

11

12

13

15

16

14

1

4

6

10

7

8

9

5

3

Overview

09

Overview

Press the INPUT key on the control
panel or the key on the remote
control.
Pressing the INPUT key will cycle the
display through all available input
signal sources in the following order.

Simply select the input that you
would like to switch to.

Input Select Key

Direct Input
Select Keys

Changing Inputs

To access the OSD menu, press menu
button on the front control panel or
press key on the remote control.

Navigation through the OSD menu can
be accomplished by using the arrow
keys on the remote control.

The On Screen Display (OSD) menu allows access to setup various parameters equipped
with this display.

After change settings on the OSD menu, the new settings are confirmed automatically
when OSD picture vanish.

OSD Menu
Navigation

OSD Menu
Access

Using the OSD Menu

The On-Screen Status Display show detailed information regarding the operational status of
the display. The status display automatically appears whenever there is a change in the
state of the display such as input change. The status display will automatically disappear
after a timeout period.

RGB Mode

RGB

1920 x 1080p 60Hz

Input Source
Signal Format

AV Mode

AV

(S-Video)

Input Source

HDMI Mode

HDMI

1080p 60Hz

Input Source
Signal Format

Component Mode

Component

1080p 60Hz

Input Source
Signal Format

On-Screen Status Display

To manually
show the
Status Display,
simply press the
key on the
remote control.
For Example:

1

1

2

2

AV

S-VIDEO

COMPONENT

RGB

HDMI1

HDMI 2

Note:

1

1

Refer to the Administrator’s Guide included with the POLYCOM video conferencing system
for configuring the monitor(s) and audio system for optimal performance.

Using Composite/S-Video

Connect the Composite/S-Video(4-pin DIN)
connector from the VCR to the Composite /
S-Video input on the back of display.

Connect the red (R) and white (L) audio jacks
from the VCR to the red (R) and white (L)
audio-in jacks located next to the back of
display.

Using Component Video Input

Connect the green-colored (labeled as Y)
jack from the DVD to the green-colored
jack of the display.

Connect the blue-colored (labeled as PB/CB)
jack from the DVD to the blue-colored PB/CB
jack of the display.

Connect the red-colored (labeled as PR/C )
jack from the DVD to the red-colored PR/CR
jack of the display.

R

Connect the red
jacks from the DVD the R and L audio-in
jacks located next to the PR/CR connector
of the display.

(R) and white (L) audio

Connecting POLYCOM Video Conferencing System

Connecting a VCR

Connecting a DVD

10

1

2

1

2

3

4

Installation

Using Composite/S-Video Input

Connect the Composite/S-Video (4-pin DIN)
connector from the DVD to the
Composite/S-Video input on the back of
display.

Connect the red (R) and white (L) audio
jacks from the DVD to the red (R) and white
(L) audio-in jacks located next to the S-Video
connector.

When Composite and S-Video are both
connected, S-Video will have higher priority.

Using HDMI Input

Connect the HDMI connector from the back
of the Set-Top Box to the HDMI connector
located on the back of the display.

Some Set-Top Boxes may not have a HDMI output. Use Component Video input or RGB
input method if this is the case.
Upon connecting your Set-Top Box to the HDMI input of the display, it may be necessary
to adjust various picture setting on the display or to correctly match the output of the
Set-Top Box. This is caused by the different video timing set by various Set-Top Box
manufacturers.
If the external device has DVI output only, use a DVI to HDMI adapter cable to connect to
the HDMI terminal.

Connecting a DVD (con’t)

Connecting a Set-Top Box

11

1

2

3

1

Notes:

1

2

3

Installation

This display can be connected to an external
amplifier using the AUDIO OUT jacks located
on the back of the display.

Connect the red (R) and white (L) AUDIO
OUT jacks from right side of the connector
panel to the external amplifier.

The AUDIO OUT RCA jacks can be set to either Fixed or Variable audio out levels.

Connect the red(R) and white(L) audio out
sockets located to the right of the connector
panel of the set respectively to the right and
left amplified speaker.

Connecting to an External Amplifiers

Connecting External Amplified Speaker

Using RGB or HDMI Video Input
For most PCs, connect the 15-pin D-Sub

RGB connector from the back of the PC to
the RGB-IN Connector located on the back
of the display.
Connect the red (R) and white (L) audio jacks
from the PC to the R and L jacks located next
to the RGB connector.

Connecting a PC

Installation

12

1

2

1

1

2

Note:

1

13

Setting Up Your Display Using Plug and Play

This display adheres to VESA Plug and Play standard to eliminate complicated and time
consuming setup of displays. This display identifies itself to the computer and automatically
sends the PC its Extended Display Identification Data (EDID) using Display Data Channel
(DDC) protocols.

How To Set Up Your Display with PC (Windows)

The display settings for a typical Windows-based computer are shown below; however,
actual screens on your computer will differ depending on the version of Windows and video
equipped with the computer. Even though the actual screen may look different from example
displayed below, basic set-up routine will apply in most cases.

Go to Window’s CONTROL PANEL by
clicking: START, SETTINGS, CONTROL
PANEL. The CONTROL PANEL Window is
displayed. Select the DISPLAY icon from this
window.

The DISPLAY PROPERTIES dialog box is
displayed. Select the SETTINGS tab to
display your computer’s video output settings.

Set the “Screen Resolution” setting to
1920x1080p PIXELS. For COLOR QUALITY,
select 24 BIT COLOR (might also be
expressed as 16 million colors).

If a vertical-frequency option exists, set the
value to 60Hz.

Click OK to complete the setting.

Note:

Both screen position and size will vary,
depending on the type of PC graphics card
and

its resolution selected.

Connecting to a PC (con’t)

1

2

3

4

5

Installation

1

2

3 4

1

Under HDMI, DVI and RGB modes, this Display supports the following resolutions:

Supported Resolutions

Installation

14

This display does not support Macintosh resolution.
“*”:not available for RGB Mode.

Note:

1

2

There are four preset picture modes that you can choose from to optimize the video picture
according to the type of programming you are watching. (1)POLYCOM; (2)CUSTOM;
(3)MILD; (4)VIVID.

CONTRAST

Adjust Contrast to increase the level of “white” in the video picture. Increasing Contrast will
make white area of the video picture brighter. Contrast works in conjunction with BRIGHTNESS.

BRIGHTNESS

Adjust brightness to enhance the level of dark area in the video picture such as night
scenes and shadow scenes. Increasing brightness will make dark areas more visible.

COLOR

Use color to adjust the color saturation of the picture. Increasing color will make the color
more intense. Reducing color setting will make the color less intense.

SHARPNESS

Use sharpness to adjust the amount of detail enhancement to the video picture. Increase
the setting will enhance the edges of objects in the video picture. Decreasing the setting will
reduce enhancement.

TINT

Use Tint to adjust the color of flesh tones. Increasing color will make the picture with more
red in appearance. Decreasing setting in left direction will shift the picture with more green
in appearance.

3D NR/MPEG NR

To improve the quality of the picture in the case of poor reception.

Picture Adjustment

Explanation of Various Picture Control Settings

Press the on the front panel or remote
control and key to enter Picture menu.
Use to select the PICTURE Option
from the menu.

Various picture settings are available
from the Picture menu. Use to adjust
that you wish and press key to confirm
select.

Menu System

1

2

PICTURE MODE

Note:
Note that the default Picture Mode setting is set to “POLYCOM”. This setting is standard mode,
which is optimized (and recommended) for use with POLYCOM Video conferencing system
all video inputs. As such, many of the adjustment sub-settings are “gray-out” and are not
accessible to the user. In order to make adjustments to these settings, “’CUSTOM” picture mode
must be selected.

15

Picture Quality Adjustment

Due to various PC video cards with different specifications, it is likely that the initial video

picture has subtle noise or imperfections. Please use the following procedures to adjust the

picture quality when using under RGB mode

Press key on the front control panel or remote control.

Use to enter Picture option from the menu.

Use keys to select AUTO ADJUST option from the menu.

Use to change the setting till your video picture is optimal.

Picture Quality Adjustment-Manual Adjustment

In certain cases, users may desire to manually adjust. To do so, please follow below
procedure. Due to various PC video cards with different specifications, it is likely that the
initial video picture may not fit exactly to the size of the display. Please use the following
procedures to adjust the picture position.

Press key on the front control panel or remote control

Use keys to select H-Position or V-Positon from the menu and press keys to confirm
selection.

Use to change the setting till your video picture is best fit within
the display area.

Fine Tuning Under RGB Mode

Menu System

Explanation of Various Picture Control Settings (con’t)

Use to change various screen width modes. There are three modes to choose from:
(1)16:9; (2) 4:3;(3)PANORAMA.

FORMAT

AUTO ADJUST

Use AUTO ADJUST to fine-tune the display to perfectly synchronize to the video signal
source under RGB mode.

COLOR TEMP.

Select the COLOR TEMP. for white balance. There are three setting to choose from:
(1)NORMAL; (2)WARM; (3)COOL.

CLOCK

Use clock to fine-tune the monitor to perfectly ADC PLL divider clock ratio synchronize to
the video signal source under RGB mode.

PHASE

Use phase to fine-tune the monitor to perfectly ADC clock phase synchronize to the video
signal source under RGB mode.

V-POSITION

Use to change vertical position of the picture. Increase to shift the picture up. Decrease to
shift the picture down.

1

2

3

4

1

3

4

Use to enter Picture option from the menu.

2

16

H-POSITION

Use to change horizontal position of the picture. Increase to shift the picture to the right.
Decrease to shift the picture to the left.

Note:
PANORAMA is only available for AV/S-Video Mode.

Press the key on the front panel or
remote control. Use to select the
SOUND option from the menu.

Various sound settings are available
from the SOUND menu. Use to select
the option that you wish to adjust.

Use to change the setting. After
achieving desired setting, press key to
close the OSD
adjusting.

or press key to keep

SOUND EFFECT

There are four preset audio modes that you can choose from: POLYCOM, MUSIC,
MOVIE and CUSTOM.

BASS

Adjusts the BASS level of the sound. For more bass response, increase the BASS level.

TREBLE

Adjust the TREBLE level of the sound. For more vocal and high frequency response,
increase the TREBLE level.

Adjusting Sound Settings

Explanation of Various Sound Control Settings

Understanding Widescreen Modes

This display is capable of displaying a wide-screen image on the native 16:9 aspect ratio
screen. However, not all available video content fits perfectly in a wide-screen (16:9) format
resulting in unused screen space. This display is capable of displaying images in various
formats that is suitable for various types of content depending on its size.

For 4:3 (Square) Content

Content from traditional TV, VCR and some DVD’s are formatted using a “square” 4:3 format.
When viewing content in this “Square” format, the following viewing modes are suitable.

16:9 (WIDE)

The original 4:3 image is proportionally stretched to fill the entire screen.
This is the default setting from factory.

PANORAMA

The original 4:3 image is stretched only on the left and right sides to fill
the screen, leaving the center image unchanged.

4:3 (NORMAL)

In 4:3 mode, the original 4:3 image is preserved but black bar are used
to fill the extra space on the left and right.

1

2

3

17

Menu System

SLEEP TIMER

After user selects the sleep time option, the display will automatically shut-off without
user intervention.

POWER SAVE

When there are no signals detected by the display, the display will automatically go into

sleep mode until signal is restored. Power save mode /feature works with HDMI/ RGB
and Component input options.

FULL SCREEN TYPE
This function is used to eliminate electrically charged residual images. There are two

functions for selection : (1) FULL WHITE; (2)MULTI-COLOR.

FULL SCREEN START

User can select (1) OFF; (2) 30 MIN; (3)60 MIN; (4)120 MIN to start FULLSCREE TYPE
function.

System Adjustment

Explanation of Various System Setting

Explanation of Various Sound Control Settings

Menu System

BALANCE

Adjusts the BALANCE level between left and right channels.

SURROUND

This display is equipped with Surround Sound circuitry. Use Surround Sound to simulate
a surround sound effect if you are not using a muti-channel sound setup.

AUDIO OUTPUT

Set the type of audio output sent from the audio output jacks located in the rear of the
display. When set to VARIABLE, audio output is affected by the display’s internal volume
controls. When set to FIXED, the audio output bypasses the display’s internal audio
control so that function such as bass, treble and volume controls have no effect.

SPEAKER

Set to On to turn on the monitor’s internal amplification and internal speakers. Set OFF
to turn off internal amplification and speakers. This setting will not effect AUDIO
OUTPUT jacks.

Press the on the front panel or remote
control. Use to select the SYSTEM
Option from the menu.

Use to select the option that you wish
to adjust.

Use to change the setting. After
achieving desired setting, press key to

close the OSD or key to keep adjusting.

1

2

3

18

AUTO POWER DOWN

After no more than 4 hours in on mode following the last user interaction, the
display shall be automatically switched from on mode to standby mode.

The following table lists possible problems and methods for remedy. Please refer to this table
prior to contacting a service representative.

Troubleshooting

Symptom

Possible Cause

Remedy

No Picture is displayed.

1. The power cord is disconnected.

2. The selected input has no connection.

3. The display is in standby mode in RGB mode.

1.Plug in the power cord.

2.Connect the selected device to the display.

3.Press any key on your keyboard.

Poor picture or poor sound.

Color is abnormal.

Image doesn’t fill up the full
size of the screen.

1. Electronic appliances, cars, motorcycles or
fluorescent lights may be nearby.

1.Move the display to another location to
reduce interference.

1. The signal cable is not connected properly.

1.Make sure that the signal cable is attached
firmly to the rear panel of the display.

Sound with no picture.

Picture with no sound.

The remote control buttons
do not work.

Some picture elements do
not light up.

After-Images can be seen
on the display after it has
been powered off.
(Examples of still pictures
include logos, video games,
computer images and images
displayed in 4:3 format)

1. The signal cable is not connected properly.

2. The input signal is not supported by the
display.

1.If under VGA mode, the Format settings
are incorrectly set.

1. The signal cable is not connected properly.

1. The signal cable is not connected properly.

2. Volume is turned all the way down.

3. The sound is muted.

1.The remote control batteries are flat or
incorrectly installed.

2.The position of the selection switch does not
correspond to the selected input.

1. Some pixels of the display may not turn on.

1. A still picture was displayed for an
extended period of time.

1.Make sure that the signal cable is attached
firmly.

2.Check that the video signal source is sup­ ported by the display (refer to the specific­ ations section).

1.Make sure that both video inputs and
sound inputs are correctly connected.

2.Use the volume adjustment buttons to
adjust sound.

3.Switch MUTE off using the MUTE button
on the remote control.

1. Change the batteries. Please note that
you must then reprogram the remote
control.

2.Put the selection switch on the correct
position.

1.This display was manufactured using an
extremely high level of technology;
however, sometimes some pixels of
the display may not display. This is not
a malfunction.

1.Do not allow a still image to be
displayed for an extended period of
time as this ca cause a permanent
after-image to remain on the screen.

Picture is distorted.

1.Use the Format options in the PICTURE
menu to adjust the size of the picture.

1.Make sure that both video and sound
inputs are correctly connected.

Addition Information

19

Specification

20

16:9

1920(Horizontal) x 1080p(Vertical) pixels

0.576 mm x 0.576 mm

2

1,345 cd/m

50” -

Display Panel

Screen size
Aspect ratio
Number of pixels

Luminance

100 ~240 Vac, 50/60 Hz

4.2A Max.
420 Watts Max.

0.4 Watts Max.

Power Source

Input voltage
Input current
Power consumption
Stand-by

Video Composite in RCA Jack x 1 set
(S-Video in jack(4 pin DIN S-Terminal) x 1 set)
Video Component RCA in Jack x 1 set
Audio L/R in Jack x 4 sets
Audio L/R Out Jack x 1 set
15 Pin D-Sub for RGB x 1 set
19 Pin HDMI x 2 sets
RS-232 x 1 set

Connection

Connector Types

Analog
Positive
S-VIDEO : Y=1VP-P (with Sync) C=0.286Vp-p (NTSC),
C=0.3Vp-p(PAL)
H:15.734KHz V:60Hz(NTSC)
H:15.625KHz V:50Hz(PAL)
75 ohms

Video/S-Video Signal

Type
Polarity
Amplitude

Frequency

Input Impedance

Analog
Positive
AV:1Vp-p(with sync), CB/PB:0.7Vp-p, CR/PR:0.7Vp-p
H:support to 15K~68KHz V:support 24~60Hz

Y/CB/CR or Y/PB/PR Signal (Component)

Type
Polarity
Amplitude
Frequency

TTL
Positive or Negative
RGB:0.7Vp-p
H:support to 27K~68KHz V:support to 24~70Hz

RGB Signal

Type
Polarity
Amplitude
Frequency

Digital
Positive or Negative
H:support to 15K~68KHz V:support 24~70Hz

HDMI Signal

Type
Polarity
Frequency

Addition Information

&

Specification

Addition Information

1. RED

2. GREEN

3. BLUE

4. GND

5. GND

6. REDGND

7. GREENGND

8. BULEGND

9. 5V

10. GND

11.NC

12.SDA

13. H-SYNC

14. V-SYNC
15 SCL

Pin Assignments For 19 Pin HDMI Connector (Digital only)

1.HDMI_RX2+

2.Ground (For +5V)

3.HDMI_RX2-

4.HDMI_RX1+

5. Ground (For +5V)

6.HDMI_RX1-

7.HDMI_RX1+

8.Ground (For +5V)

9.HDMI_RX0-

10.HDMI_RXC+

11.Ground (For +5V)

12.HDMI_RXC-

13.No Connect

14.Connect

15.RX5VDDC SCL

16.RX5VDDC SDAt

17. Ground (For +5V)

18. IN_5V

19. RX_HOTPLUG

Pin Assignments For D-Sub connector (In/Loop out)

21

Timing For Component

Maximum Resolution Up to 1920 x 1080p

This display does not support Macintosh resolution.

Note:

1
2

Analog 500mV rms/more than 10K ohm.

Audio Signal

Dimensions & Weight

Without SPK With SPK Without SPK With SPK
Without/STAND With/STAND With STAND Without STAND
Width 1256mm 1436mm 1256mm 1436mm

Height 762mm 793mm 793mm 762mm

Depth 135.7mm 260mm 260mm 135.7

Net Weight 68.3lbs/31Kg 79.4lbs/36Kg 72.8lbs/33Kg 75.0lbs/34Kg

Gross Weight 88.2lbs/40Kg 99.2lbs/45Kg 92.6lbs/42Kg 94.8lbs/43Kg

Addition Information

Specification

Operating

Temperature

0

0~40 C
Relative Humidity 20~80%
Pressure 600~835 mm/hg

Non-Operating

Temperature

0

-20~60 C
Relative Humidity 20~80%
Pressure 562~835 mm/hg

Acoustics

(IHF A-weight 1 meter) 30dB Max.

Sound

Residual hum(at volume Max.) 100 W Max.u
Practical Max. Audio Output (at 10% THD Max.) 10W+10W Max./14 ohm

Sound Distortion (at 250mw 1KHz) 1% Max.
Audio Output (input at 1.4Vp-p) >=1.0Vp-p

Reliability Requirement

0

The MTBF is 100,000 hrs. under operation 25 5 C (Half luminosity, motion

picture)

+

Emission Requirement

The unit shall meet the EMI limits in all screen modes as qualified by CB/CE/UL/FCC/

VCCI/ CCC/BSMI/Gost-R/S-Mark/Spring Mark and KC.

22

Power Management

Mode
Normal
Stand-by
Power Saving
Power Saving

H-sync
Pulse
No pulse
Pulse
No pulse

V-sync
Pulse
No pulse
No pulse
Pulse

Video
Active
No video
B(blanked)
B(blanked)

Power Dissipation
Normal power
Less than 0.5 Watt
Less than 0.5 Watt
Less than 0.5 Watt

The power indicator LED color is green in normal state, orange in stand-by and power
saving state.

Specification

Addition Information

Note:

23

1

This display offers a power management feature that is enabled by default, and that can be
used to automatically transition from On Mode to Sleep Mode.

2

RS-232 Connection

This monitor is equipped with an RS-232 serial terminal for using the monitor with computer controls.
The RS-232 serial terminal conforms to the RS-232 interface specification. The computer will require
software application (such as Hyper Terminal) which allows the computer to send and receive control
data that can support the communication parameters described in the section.

Interface Parameters

These parameters are required to setup communications with the monitor.
Specification

Sync Method
Baud Rate
Parity
Character Length
Stop Bit

RS-232
Synchronous
9600 bps
None
8 Bits
1 Bits

RS-232 Pint Layout
Pin 1 Received Line Signal Detector (Data Carrier Detect)
Pin 2 Received Data (RXD)
Pin 3 Transmit Data (TXD)
Pin 4 Data Terminal Ready (DTR)
Pin 5 Signal Ground
Pin 6 Data Set Ready (DSR)
Pin 7 Request To Send (RTS)
Pin 8 Clear To Send (CTS)
Pin 9 Ring Indicator

1

2

3

4

5

6

7

89

RS-232

Command Format and Sequencing

Data Structure Overview

In order to transmit data from the computer to the display, the data must be sent in a structured
format. The format used by this display follows a COMMAND:DATA sequence. All commands and
its related data are formatted using a 3-character format separated by a colon in-between. For
example, the Power On command is sent as: PWR:PON where PWR is telling the display that it is
receiving a Power related command, followed by the actual command to carry out.

Communications Overview

As commands are sent from the PC,
the display will provide feedback
regarding the state of command
execution back to the PC. The
display provides information status
to inform the following:
Whether the command sent by
the computer was received by
the display.
Whether the COMMAND : DATA
structure was correctly formatted
for execution by the display.

Whether the command sent
was successfully carried out by
the display.

Addition Information

Overview

PC sends
command to
display

Display
busy?

Display sends
BZY(busy)
status to PC

Display sends
RCV(received)
status to PC

Command
structure sent
correctly?

Display executes
command

Display sends
CFM(confirm)
status to PC

Display sends
FAL(Failure)
status to PC

The following is an example of the communication
process between the PC and the display using a program such as Hyper Terminal.
Example: Read Power Status followed by Power On command and input select to AV with disruption.

24

1

2

3

>REA:PWR
>RCV
>OFF
>CFM
>PWR:PON
>RCV
>CFM
>INP:AV1
>BZY
>
>RCV
>CFM
>INP:AV1
>RCV
>CFM
>

PC Status

Send command to read power status
Rcv acknowledgment of command received
Rcv OFF status from display
Rcv confirmation of command complete
Send command to POWER ON the display
Rcv acknowledgment of command
Rcv confirmation of command complete
Send command to switch to AV1 input
Rcv acknowledgment of command not accepted
Send command to void previous command
Rcv acknowledgment of command received
Rcv confirmation of command complete
Send command to switch to Av1 input again
Rcv acknowledgment of command received
Rcv confirmation of command complete
Ready to send another command

Display Status

Display rcv command
Send confirmation of comm and rcv’d to PC
Send actual status of power to PC(OFF)
Send confirmation of command completion
Display is not busy and waiting for command
Send confirmation of command rcv’d to PC
Display powers on and sends confirmation
Display is busy doing another task
Send busy status because it can’t rcv data
Rcv command to clear previous command
Send confirmation of command rcv’d to PC
Clear command buffer and sends confirm
Display is not busy and rcv’s command
Send confirmation of command rcv’d to PC
Display switche to AV1 and sends confirm
Display is ready to accept another command

25

Addition Information

Command Format and Sequencing

Communications Overview

Command and Data Tables

Description

Read Data

Power On/Off
Brightness
Contrast
Color
Tint
Sharpness
Input Select
V-Position
H-Position
Recall
Mute
Language

All Black
Polycom mode
Aspect Ratio
Keypad Lock
Color Temp
Volume
Bass
Treble
Balance
Display Model Name
Return Model Name
Power On Source

Command

REA

PWR
BRT
CON
CLR
TNT
SHP
INP
VPS
HPS
RCL
MUT
LNG

BLK
PLC
ZOM
FPL
TMP
VOL
BAS
TRB
BAL
DSP
REA
POS

Data

PWR,BRT, CON, CLR, TNT, SHP, INP, MUT, LNG, TMP, ZOM, FPL,

PLC, VPS, HPS, RCL, VOL, BAS, TRB, XBS, PAS, DSP, REA POS, BLK,

PON=Power On, OFF=Power Off

001...100

001...100

001...100

001...100

001...100
CP1=Component, RG1=RGB, HDM=HDMI1, HM2=HDMI2

001...100

001...100
000
MON=Mute, OFF=Normal
ENG=English, SPA=Spanish, FFR=French, ITA=Italian, DEU=German,

SWE=Swedish
BON=All Black, OFF=Return

000
WID=16:9, NOR=4:3 with black bars, PAN=PANORAMA(Only AV/S mode)
FO1=Lock, OFF=Unlock
MID=Natural, HIG=Cool, 65D=Warm

001...100

001...100

001...100

001...100
INF (Example: DSP:INF RCV CFM PMP-50FPSM(ML) )
INF (Example: REA:INF RCV CFM PMP-50FPSM(ML) )
OFF=Normal (Last Memory) CP1=Component, RG1=RGB, HDM=HDMI1,

HM2=HDMI2

Enter

Enter

Enter

Enter

Enter

Dimensional Drawings

Color Scheme

26

Addition Information

Packing Break Out

27

Addition Information

TLABM1806Y1----

YRC-294POLYCOMB

TINSE2227Y1----

SPAKC0871Y1R--W