Polk Mono Striker prozx Setup Manual

Premium Audiophile Grade Gaming Headset

Setup Guide

2

Note: For optimal performance, switch off Mic Boost during PS4 online gaming
and chat. Switch on Mic Boost for all other devices, unless experiencing
distortion when speaking loudly.

Contents

mic muted

mic unmuted

Detachable boom

microphone with instant
mute toggle button

3 m PC connect cable

1 m console connect cable

1 m mobile connect cable

In-line volume control with

mic attenuator for PS4
(compatible with all consoles)

Polk XBox One

headset adapter

2

3

4

6

5

1

3

Device Connectivity Chart

PC Laptop XBox PS4 Wii U Connector

Setup

Xbox One

1

2

1. Plug the Wireless Headset Adapter into the
Xbox One controller.

2. Use the 1m console cable and connect it
from the Striker Pro into the 3.5 mm input
jack on the Wireless Headset Adapter
(please make sure the headphone plug is
pushed all the way in).

4

2

3

4

PS4

Use the 1 m console cable and connect it from the Striker Pro into the in-line
volume control with mic attenuator device. Then, connect it into the 3.5 mm
input jack on the PlayStation® Dualshock 4 controller (please make sure the

headphone plug is pushed all the way in).

Use the following instructions to route all audio output
to headset:

1. Press and hold the home button for 3 seconds
(Mic Boost should be off), then select “Adjust Devices”

and press the “X” button.

2. Select “Output to Headphones” and press
the “X” button.

3. Choose “All Audio” and press the “X” button.

4. Select in-line volume control with mic attenuator
(Headphones).

5. Select Microphone (Level Menu).
Note: To adjust the microphone level, go to “Settings,” then “Device Settings,”

then “Audio Devices” and adjust the microphone level.

Wii U

Use the 1 m console cable and connect it from the Striker Pro into the 3.5 mm
input jack on the WiiU controller (please make sure the headphone plug is

pushed all the way in).

5

PC

Use the 3 m PC connect cable and connect it from the Striker Pro into the
headphone output jack and microphone input jack (pink and green) on your
PC (please make sure the headphone plug is pushed all the way in).

Note: Older model PCs may not be

compatible. For additional support,
contact customer service at
[phone].

Mac Laptops and Mobile

Use the 1 m console cable and connect it

from the Striker Pro into the 3.5 mm input
jack on your mobile device (please make

sure the headphone plug is pushed all
the way in).

Note: Compatible with 2008 or newer

MAC laptops.

6

Adapter

Master Volume Control

| Increases/decreases the volume in 1-24 increments
| Press/hold either button to jump multiple volume increases/decreases
| Beeps at full chat audio and full game audio

Chat/Game Volume Mixer

| Increase one (e.g. chat) while decreasing the other (e.g. game)
| Press/hold to jump multiple increases
| Beeps at minimum (after 1) and maximum volume (after 24)

Mute

| One press mutes the microphone (solid LED shows)
| Press/hold 2 seconds to mute chat and game (flashing LED shown)
| Unmute chat or game by increasing volume

Side Chat On/Off

| Press and hold game volume and volume up buttons for longer than

5 seconds to toggle side chat on/off

| This setting will be retained even after the adapter is disconnected

from the controller or power is lost

Important Note(s):

Your settings save even if your
headset disconnects from the
adapter (unless power is lost or
the adapter is unplugged, settings
will default to level 12).

Mute

Chat Balance

Increase

Game Balance

Increase

Master Volume

Increase

Master Volume

Decrease

7

Product Information

Your Polk Striker Pro Headset

| Engineered for a lightweight and comfortable design
| Ear cups pivot to conform to your head for a comfortable, secure fit
| Multiple cables provided for ultimate flexibility—use your headset

with nearly any device

Detachable Boom Microphone

Mic is flexible and can be shaped to suit your chat style. For the highest clarity, it
is recommended that the microphone be positioned inline with the corner of your
mouth to prevent plosives and wind noise. Activate mute when button is depressed.

Cleaning Your Headset

| Use a damp cloth to clean the headset
| DO NOT get any liquid in the headset
| Use warm water and a mild dish soap on a damp cloth to remove dirt
| DO NOT use harsh cleaning agents

Storing Your Headset

| Store your headset in a clean, dry environment
| DO NOT expose your headset to extreme heat, cold, high humidity or liquids

Troubleshooting

Boom Microphone Is Not Working

Make sure it’s securely inserted into the headset (you should feel it click into
place) and not muted (push button is not activated).

Volume Is Low

Turn the in-line remote or Xbox One headset adapter up. Make sure cable is
securely connected.

Headset Lacks Bass

Adjust the headset to fit properly, creating a good seal around the ear.
Make sure the cable is securely connected.

8

Limited 1-year warranty

(US and Canada) / 2-year warranty for EU and UK. Polk, Inc., warrants, to the original retail purchaser
only, that this Polk Headphone Product will be free from defects in material and workmanship for a
period of one (1) year from the date of original retail purchase from a Polk Authorized Dealer. This
warranty will terminate automatically prior to its stated expiration if the original retail purchaser sells
or transfers the product to any other party. To allow Polk to offer the best possible warranty service,
please register your new product online at: www.polkaudio.com/registration or call Polk Customer
Service at 800-377-7655 in the USA and Canada (outside the USA: [phone]) within ten
(10) days of the date of original purchase. Be sure to keep your original purchase receipt. Defective­Products must be shipped, together with proof of purchase, prepaid insured to the Polk Authorized
Dealer from whom you purchased the Product, or to the Factory at 1 Viper Way, Vista, California

92081. Products must be shipped in the original shipping container or its equivalent; in any case
the risk of loss or damage in transit is to be borne by you. If upon examination at the Factory or Polk
Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time
during this Warranty period, Polk or the Polk Authorized Dealer will, at its option, repair or replace this
Product at no additional charge, except as set forth below. All replaced parts and Products become
the property of Polk. Products replaced or repaired under this warranty will be returned to you, within
a reasonable time, freight prepaid. This warranty does not include service or parts to repair damage
caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures,
commercial use, voltage inputs in excess of the rated maximum “of the unit, cosmetic appearance
not directly attributable to defect in materials or workmanship, or service, repair, or modification of
the Product which has not been authorized or approved by Polk. This warranty shall terminate if the
Serial number on the Product has been removed, tampered with or defaced. This warranty is in lieu of
all other expressed Warranties. If this Product is defective in materials or workmanship as warranted
above, your sole remedy shall be repair or replacement as provided above. In no event will Polk, Inc.
be liable to you for any incidental or consequential damages arising out of the use or inability to use
the Product, even if Polk, Inc. or a Polk Authorized Dealer has been advised of the possibility of such
damages, or for any claim by any other party. Some states do not allow the exclusion or limitation
of consequential damages, so the above limitation and exclusion may not apply to you. All implied
warranties on this Product are limited to the duration of this expressed Warranty. Some states do not
allow limitation on how long an implied Warranty lasts, so the above limitations may not apply to you.
This Warranty gives you specific legal rights, and you also may have other rights which vary from state
to state. This Warranty applies only to Products purchased in Canada, the United States of America,
its possessions, and U.S. and NATO armed forces exchanges and clubs. The Warranty terms and
conditions applicable to Products purchased in other countries are available from the Polk Authorized
Distributors in such countries.

9

Customer Service

If you have an issue with your purchase, please contact the authorized Polk
dealer where you made your purchase, or contact Polk Customer Service
immediately at 1-800-377-7655 (M-F, 9 a.m. - 5:30 p.m. EST, USA and
Canada only). If, after following the setup directions, you experience difficulty,
please double-check that you followed the instructions correctly. Should you
isolate the problem to a defect in the headphones, contact the authorized Polk
dealer where you made your purchase, or contact Polk Customer Service by
phone or via email at [e-mail]. Outside the USA and Canada,
call [phone].

Product Disposal

Certain international, national and/or local laws and/or regulations may apply
regarding the disposal of this product. For further detailed information, please
contact the retailer where you purchased this product or the Polk Importer/
Distributor in your country.

Important Performance & Safety Tips

WARNING

Please listen carefully. Polk headphones are capable of playing at extremely
high volume levels, which could cause serious or permanent hearing damage.
Polk, Inc. accepts no liability for hearing loss, bodily injury or property damage
resulting from the misuse of its products.

Enjoy Responsibly

Use your good common sense and never play headphones in an environment,
or during an activity, that requires your complete attention. The sounds you
hear around you could save your life.

How Loud Is Too Loud?

Limit prolonged exposure to volumes that exceed 85 decibels (dB). Regular
exposure to sound over 100 dB for more than 1 minute risks permanent hearing
loss. For more about safe volume levels, go to the Occupational Health and
Safety Administration (OSHA) guidelines at www.osha.gov.

10

Contenu

Microphone sur tige

amovible avec sourdine
à bouton pressoir

Câble-PC 3 m

Câble-console 1 m

Câble-mobile 1 m

Contrôle de volume et atténuateur

de micro sur cordon pour PS4
(compatible avec toute console)

Note : Pour une performance optimale,désactivez la fonction Mic Boost

lorsque vous clavardez ou jouez en ligne. Activez Mic Boost pour tout autre
dispositif sauf si vous entendez de la distorsion lorsque vous parlez fort.

Adaptateur Polk Xbox One
pour casque

2

3

4

5

sourdine

actif

6

fr

1

11

Tableau de connexion

PC Portable XBox PS4 Wii U Connecteur

Installation

Xbox One

1. Branchez l’adaptateur pour casque sans fil dans
le contrôleur Xbox One.

2. Utilisez le câble-console 1 m pour raccorder

le Striker Pro à la prise d’entrée 3,5 mm de
l’adaptateur pour casque sans fil (assurez-vous
que la fiche d’écouteur est bien branchée.)

4

2

3

1

2

12

PS4

Connectez le câble-console 1 m du Striker Pro au dispositif “contrôle de
volume/ atténuateur de micro” sur cordon. Branchez ensuite le dispositif à la
prise 3,5 mm du contrôleur du PlayStation® Dualshock 4 (assurez-vous que la

fiche d’écouteur est bien branchée.)

Suivez les instructions suivantes pour acheminer toute
source audio au casque d’écoute :

1. Appuyez sur le bouton Home pour 3 secondes
puis sélectionnez «Adjust devices» et
appuyez sur le bouton «X».

2. Sélectionnez «Output to Headphones» et
appuyez sur le bouton «X».

3. Sélectionnez «All Audio» et appuyez sur le bouton «X».

4. Sélectionnez «In-line volume control with mic
attenuator for PS4» (Headphones).

5. Sélectionnez Microphone (Level Menu).
Note : Pour régler le niveau du microphone, sélectionnez «Settings» (réglages)

puis «Device Settings» puis «Audio Devices» et réglez le niveau du microphone.

Wii U

Utilisez le câble-console 1 m pour raccorder le Striker Pro à la prise
d’entrée 3,5 mm du contrôleur Wii U (assurez-vous que la fiche d’écouteur

est bien branchée.)

13

PC

Utilisez le câble-PC 3 m pour raccordez le Striker Pro aux entrées prise
d’écouteurs et microphone (rose et verte) de votre PC (assurez-vous que la

fiche d’écouteur est bien branchée.)

Note : Les anciens PC pourraient ne

pas être compatibles. Pour assistance
technique, contactez le Service à la
clientèle au [phone].

Portables Mac et dispositifs mobiles

Utilisez le câble-console 1 m pour raccorder

le Striker Pro à la prise d’entrée 3,5 mmde
votre dispositif. (Assurez-vous que lafiche

d’écouteur est bien enfoncée.)

Note : compatible avec les Mac 2008 et

plus récents.

14

Adaptateur

Contrôle de volume principal

| Monte/baisse le volume en incréments de 1 à 24
| Appuyez sur + ou – en continu pour monter/baisser le volume
| Émet in bip au volume max. de jeu et de clavardage

Contrôle de balance clavardage/jeu

| Monte l’un (p. ex. clav.) tout en baissant l’autre (p. ex. jeu)
| Appuyez en continu pour balancer graduellement
| Émet in bip à volume minimum (1) et maximum (24)

Sourdine

| Une pression met le micro en sourdine (DEL allumée)
| Appuyez 2 secondes pour mettre le clavardage et le jeu en sourdine

(DEL clignotante)

| Pour réactiver le son du clavardage et du jeu, montez le volume

Side Chat On/Off

| Appuyez sur les boutons + du volume principal et du volume de jeu pour

plus de 5 secondes pour active/désactiver le Side Chat.

| Ce réglage sera retenu même si l’adaptateur est déconnecté du

contrôleur ou dépourvu d’alimentation

Note importante :

Vos réglages seront conservés
même si votre casque est
déconnecté de l’adaptateur.
(Si l’adaptateur est déconnecté
ou privé d’alimentation, le niveau
par défaut est 12.)

Sourdine

Balance clavardage

+

Balance jeu

+

Volume principal

+

Volume principal

–

15

Information sur le produit

Votre casque Polk Striker Pro

| Conçu pour assurer légèreté et confort
| Les oreillettes pivotent pour assurer un ajustement ferme et confortable
| Plusieurs câbles sont fournis pour assurer une polyvalence optimale, vous

permettant d’utiliser le casque avec presque n’importe quel dispositif

Microphone sur tige amovible

La tige est flexible pour se plier à votre style de clavardage. Pour une clarté
optimale, le microphone devrait être placé au coin de la bouche pour éviter
les bruits de souffle. Le bouton pressoir active/désactive le mode sourdine.

Nettoyage du casque d’écoute

| Pour le nettoyer, utilisez un chiffon doux humide
| Pour le décrasser, utilisez un chiffon, de l’eau tiède et du savon à vaisselle
| Ne laissez JAMAIS DE LIQUIDE pénétrer le casque
| N’UTILISEZ JAMAIS de nettoyant caustique

Rangement de votre casque

| Rangez votre casque dans un endroit sec et propre
| NE L’EXPOSEZ PAS au froid/chaleur extrême, à l’humidité élevée ou aux liquides

Dépannage

Le microphone sur tige ne fonctionne pas

Assurez-vous qu’il est bien branché dans le casque (il devrait cliquer en place).

Volume très bas

Montez le volume de la télécommande du cordon ou de l’adaptateur XboxOne.
Assurez-vous que le cordon est bien branché.

Graves très faibles

Ajustez le casque pour qu’il entoure et scelle bien vos oreilles.
Assurez-vous que le cordon est bien branché.