Polk Audio M50, M70, M40 User Manual

HP Pavilion
M40, M50, and M70
Multimedia
Displays

User’s Guide

English

Displays

HP Pavilion M50 and M70 Multimedia

Notice

The information contained in this
document is subject to change without
notice.

Hewlett-Packard
warranty of any kind with regard to
this material, including, but not
limited to, the implied warranties of
merchantability and fitness for a
particular purpose.

HP shall not be liable for errors
contained herein or for incidental or
consequential damages in connection
with the furnishing, performance, or
use of this material.

HP assumes no responsibility for the
use or reliability of its software on
equipment that is not furnished by HP.

®

Company makes no

ii

This document contains proprietary
information that is protected by
copyright. All rights are reserved. No
part of this document may be
photocopied, reproduced, or translated
to another language without the prior
written consent of HP.

Hewlett-Packard Company
Home Products Division
P.O. Box 4010
Cupertino, CA 95015-4010

©1998 Hewlett-Packard Company. All
rights reserved.

1 Introduction

HP Pavilion Multimedia Displays

Hewlett-Packard is a registered
trademark of Hewlett-Packard Company
in the United States of America and
other countries.

Other brand or product names are
trademarks of their respective
holders.

English

iii

Table of Contents

1 Introduction 1

For Your Safety 2

2 Installation 5

Unpacking the Display 5
Locating the Display 5
Connecting the Power and Video

Cables 6
Connecting the Speakers 8

3 Using the Display 11

Turning the Display On and Off 11
Degaussing the Display 12
Setting the Screen Resolution 13
Minimizing Eyestrain 13
Minimizing Energy Use 14
Care and Cleaning 15

Cleaning the Screen 15

Adjusting the Viewing Angle 17

4 Changing Display Settings 19

Using the Front Panel 19
Setting the Custom Preset Modes 20

Changing Mode Settings 22

Adjusting the Brightness and
Contrast 24

Using the OSD Main Window 25

Choosing the Color Temperature
29
Setting Red, Green, and Blue
Values 31

English

v

1 Introduction

HP Pavilion Multimedia Displays

5 Technical Information 35

M40 Display Information 35

M40 Video Modes 37
M40 Pin Assignments 38

M50 Display Information 40

M50 Video Modes 41
M50 Pin Assignments 43

M70 Display Information 44

M70 Video Modes 45
M70 Pin Assignments 47

DPMS Power-Management Features 48

6 Regulatory Information 51

FCC Statement 51
X-Ray Radiation Notice 52
General Notice 53

vi

1 Introduction

The HP Pavilion M40, M50, and M70
Multimedia Displays (Models D5269A,
D5258A, and D5259A) are high­resolution, multi-scan color monitors
designed for use with HP Pavilion and
other computers. Each display includes
a built-in microphone and mounts for
the speakers supplied with HP Pavilion
computers. The displays comply with
EPA ENERGY STAR standards and include
automatic power-management features.

Other features include



Non-glare picture tube to reduce
the reflection of ambient light
(except U.S. M40 models).



On-screen adjustment of display
settings.



Compliance with Swedish MPR II
guidelines for reduced
electromagnetic emissions (except
U.S. M40 models).



Support for high refresh rates to
reduce screen flicker and
eyestrain.



Built-in tilt and swivel base.

English

1

1 Introduction

HP Pavilion Multimedia Displays

Microphone

WARNING

Control

Power button

For Your Safety

For your safety and the protection of
your display, follow these
precautions:



Always connect the display to a
grounded, three-prong power outlet.
Use only the factory-supplied power
cord.

To completely disconnect power from
the display, you must remove the power
cable from the power socket.



To prevent electrical shock, do not
remove the back cover of the
display. The cover should be
removed only by qualified service
personnel.



Position the display so the power
cord is accessible.



Do not place objects on top of the
display that could fall into the
vents or block airflow.

2

1 Introduction

HP Pavilion Multimedia Displays



To avoid the risk of damage to the
display and electrical shock to
yourself, do not expose the display
to rain or moisture.



Adjust only those controls whose
operations are covered in this
manual. Improperly adjusting other
controls may result in damage and
could require repair by a service
technician.

If any of the following conditions
occur, unplug the display and contact
a qualified service technician:



The power cord or plug is frayed or
damaged.



You have spilled liquid into the
display.



The display has been exposed to
rain or water.



The display does not operate
correctly when the operating
instructions are followed.



The display has been dropped or the
cabinet has been damaged.



The performance of the display
changes abruptly.

English

3

2 Installation

Follow the instructions in this
chapter to install your
HP Pavilion M40, M50, or M70
Multimedia Display.

English

NOTE

Before installing the display, refer
to your computer and video adapter
documentation. You may need to make
changes to accommodate the display.

Unpacking the Display

When you unpack the display, make sure
that you have the following items:



The display with its attached video
cable and pedestal mount



A power cord

Locating the Display

Place the display on a flat, sturdy
surface. If you plan to use the
display with a desktop PC, you can
place it on top of the computer. (If
you’re not using an HP Pavilion
computer, check the documentation for
the maximum weight the computer’s case
can hold.)

Choose an area that is free from
excessive heat, moisture, and
sunlight. Avoid possible sources of
electromagnetic interference, such as
transformers, motors, fluorescent
lighting, and other computer displays.

5

2 Installation

HP Pavilion Multimedia Displays

Connecting the Power and
Video Cables

Before connecting any cables, make
sure to read the safety instructions
at the beginning of the manual. The
computer and display must be turned
off.

6

2 Installation

HP Pavilion Multimedia Displays

To connect the power and video cables

1. Connect the power cord to the back
of the display.

2. Plug the power cord into a power
outlet.

3. Connect the orange plug on the
video cable to the video port of
your computer. If you have an HP
Pavilion computer, this port is
marked in orange. (The illustration
below is for reference only. Check
your computer manual for the video
port location.)

English

7

Video

connector

2 Installation

HP Pavilion Multimedia Displays

Microphon
e

4. Plug the yellow microphone
connector into the sound input port
of your computer. On HP Pavilion
computers, the port is marked in
yellow.

Connecting the Speakers

The display is designed for use with
the HP/Polk Audio speakers supplied
with HP Pavilion computers.

To connect the speakers

1. Extend the cables attached to the
two speakers.

2. Identify the left and right
speakers. You can tell which side a
speaker fits onto by observing its
curvature and mounting pegs. The
side of the speaker with mounting
pegs fits flush against the side of
the display.

3. Fit the pegs of the right speaker
into the corresponding holes on the

8

2 Installation

HP Pavilion Multimedia Displays

right side of the display, then
push down until the speaker is
secure.

English

9

2 Installation

HP Pavilion Multimedia Displays

4. Clip the speaker wires to the
underside of the monitor as shown
in the illustration.

5. Plug the two speaker wire

Y-

connectors into the Y-connector.

6. Plug the single connector on the
end of the Y-connector’s cable to
the sound-out port on your
computer. (Check in the computer’s
documentation for the location of
the port.)

10

3 Using the Display

This chapter contains information
about using your HP Pavilion M40, M50,
or M70 Multimedia Display.

Turning the Display On
and Off

You use the power button on the front
panel to turn the display on and off.
When the display is on, the light near
the power button is illuminated. The
light is green when the display and
computer are active and amber when the
display is in one of its reduced power
modes.

The display’s power management
features reduce power consumption to
low levels when your computer has been
inactive for a specified period of
time. See “Minimizing Energy Use”
later in this chapter for more
information.

English

Because of the display’s power
management features, you don’t
normally need to turn off the display
when it’s not in use. When turned off,
the display uses the same amount of
power that it uses in sleep mode (less
than eight watts).

If your computer doesn’t support DPMS
power management, you can reduce power
consumption by turning off the monitor
when it won’t be used for an extended

11

3 Using the Display

HP Pavilion Multimedia Displays

period. You can turn the display off
even if you leave the computer
running.

WARNING

To completely disconnect power from
the display, you must remove the power
cable from the power socket.

To turn the display on or off



Press the power button on the front
of the display.

Degaussing the Display

Each time you turn on the display, it
is automatically
removes magnetism that causes unwanted
color variations. Degauss the display
any time you notice unusual color
variations. If you leave the display
continuously turned on or frequently
change its position, you should
degauss about once a week.

To degauss the M40 or M50 display,
turn it off for about 30 minutes. When
you turn the display on again, there
will be a short humming sound and a
momentary instability in the image.

There are two degaussing options for
the M70 display. You can either turn
off the display as described for the
M40 and M50, or use the degauss option
in the OSD main window. See “Using the
OSD Main Window” in Chapter 4 for
instructions.

degaussed

. Degaussing

12

3 Using the Display

HP Pavilion Multimedia Displays

Setting the Screen
Resolution

screen resolution

The
amount of information shown in the
display. Screen resolution refers to
the number of the dots or
to make up an image. A low screen
resolution means that the display uses
a relatively small number of
relatively large dots. A higher
resolution means that more dots of a
smaller size make up the image. With
higher screen resolutions, icons,
windows, and text are smaller on the
screen, but more information can be
displayed.

The screen resolution is set on the
computer. The display supports many
common screen resolutions, as shown in
“M40 Video Modes,” “M50 Video Modes,”
and “M70 Video Modes” in Chapter 5.
Check the documentation supplied with
your computer and video adapter to
find out which resolutions they
support.

determines the

pixels

used

English

Minimizing Eyestrain

To minimize eyestrain and avoid screen
flicker, use the highest possible

image refresh rate
frequency

at the current screen resolution. (The
image refresh rate is the number of
times per second that the image is
refreshed.) The tables in “M40 Video
Modes,” “M50 Video Modes,” and “M70

supported by your computer

vertical

or

13

3 Using the Display

HP Pavilion Multimedia Displays

Video Modes” in Chapter 5 show the
image refresh rates supported by the
displays at different screen
resolutions.

Minimizing Energy Use

All HP Pavilion computers and many
other computers support

power management

. Power-management
features reduce the display’s power
consumption after a period of keyboard
inactivity.

The display supports three different
power-saving modes—standby, suspend,
and sleep—which reduce consumption to
less than eight watts. See “DPMS
Power-Management Features” in Chapter
5 for a description of the
characteristics of each mode.

VESA display

14

When the display is in one of its
power saving modes, the screen is
blanked out and the front panel power
indicator is amber. Pressing a key on
the keyboard or moving the mouse
restores the image. Consult your
computer’s documentation for
information about setting the power­saving modes.

3 Using the Display

HP Pavilion Multimedia Displays

Care and Cleaning

To maximize screen life and prevent
damage to the picture tube, HP
recommends that you



Use the display power-management
system (if available on your
computer) or a screen saver
program.



Turn off the display or reduce its
brightness and contrast to minimum
levels when you won’t be using the
display for an extended period.
This is particularly important if
you don’t use a power-management
system or screen saver.



Avoid setting contrast and
brightness to maximum levels or
using the Gaming preset mode for
prolonged periods.

Cleaning the Screen

The screen of the display has a high­quality optical coating that reduces
glare and static buildup. To prevent
damage to this coating, use only
regular household glass cleaner to
clean the screen.

English

CAUTION

Don’t use cleaning solutions
containing fluoride, acids, or
alkalis. Never use hard or abrasive
cleaning products to clean the screen.

To clean the screen

1. Turn off and unplug the display.

15

3 Using the Display

HP Pavilion Multimedia Displays

2. Spray a soft cotton cloth with

glass cleaner and gently wipe the
screen.

3. Dry the screen with a soft cotton

cloth.

4. Plug in the display and turn it on.

16

3 Using the Display

HP Pavilion Multimedia Displays

Adjusting the Viewing
Angle

The display’s pedestal mounting
enables you to adjust the viewing
angle. You can tilt and turn the
display to find the most comfortable
viewing position.

English

17

3 Using the Display

HP Pavilion Multimedia Displays

18

4 Changing Display
Settings

MODE

You use the OSD (On-Screen Display)
features of the Pavilion displays to
change their settings. The buttons on
the front panel control on-screen
icons and windows.

Using the Front Panel

You use the six buttons on the front
of the display to control OSD
functions.

The Mode button allows you to choose
from the display’s custom preset
modes. See the next section, “Setting
the Custom Preset Mode,” for
instructions.

The brightness button opens and
closes the brightness adjustment
window.

The contrast button opens and closes
the contrast adjustment window.

English

SELECT

The Select button opens the OSD main
window if no other OSD windows are
displayed. In the OSD main window,
the Select button opens the
adjustment window for the selected
icon.

19

4 Changing Display Settings

HP Pavilion Multimedia Displays

The minus button decreases a setting
if an adjustment window is open. In
the OSD main window, the button moves
backward through the icons.

The plus button increases a setting
if an adjustment window is open. In
the OSD main window, the button moves
forward through the icons.

Setting the Custom
Preset Modes

Your display is configured for
excellent performance right out of the
box. If you want to optimize the
display’s settings for a particular
activity, however, you can use custom
preset modes.

Custom preset modes enable you to
quickly change contrast and color
settings to match those commonly used
for various activities and viewing
conditions. The three preset modes are
Productivity, Photos/Graphics, and
Gaming.

20

The display also includes a Personal
Setup mode, whose contrast,
brightness, and color settings you can
define. (See the next section,
“Changing Mode Settings,” for
information about defining the
Personal Setup mode and temporarily
changing settings for the other
modes.)

4 Changing Display Settings

HP Pavilion Multimedia Displays

You choose the mode in the Mode
window, which displays the following
icons:

Productivity mode is designed for
best results in office environments
and with applications like word
processors and spreadsheets.

Photos/Graphics mode has the same
settings used by graphics
professionals in photographic and
pre-press applications and
environments.

Gaming mode offers higher contrast
and the same color settings found in
TV and arcade games. It is also
appropriate for viewing full-motion
video. HP recommends that Gaming
mode not be used for productivity
applications.

Personal Setup mode enables you to
define and save colors and settings
for your own purposes.

English

21

4 Changing Display Settings

HP Pavilion Multimedia Displays

To set the display mode

1. Press the Mode button to display

the Mode window.

2. To immediately change to the next

mode, press the Mode button again.
(Alternatively, press the + or –
button to move through the icons.)

3. When the display mode you want is

highlighted, press the Select
button to close the Mode window.
(Alternatively, wait five seconds
for the window to close
automatically.)

Changing Mode Settings

The custom preset modes were designed
for quick access to common settings.
You can’t permanently change these
settings, but you can make

temporary

adjustments to the contrast, and color
to meet a particular need. These
changes are lost if you change to
another mode or turn off the display.

22

For example, if you change the
contrast level while working in Gaming
mode, switch to Productivity mode,
then return to Gaming mode, the
original factory default contrast
level will be in effect.

4 Changing Display Settings

HP Pavilion Multimedia Displays

If you turn off the display, it will
be in Personal Setup mode when you
turn it back on. Any changes
previously made to Productivity,
Photos/Graphics, or Gaming modes are
lost.

The display’s power-saving features
don’t affect temporary changes to
custom preset modes. If you leave the
computer inactive long enough to
trigger its power-management system,
or if you turn off the computer, the
temporary changes will still be in
effect when the display returns from
its power-saving state.

If you want to define and save
settings, use Personal Setup mode.
Personal Setup initially has the same
settings as Productivity mode. When
you’re working in Personal Setup mode,
however, adjustments to brightness,
contrast, and color are automatically
saved and remain in effect until you
change them.

English

In addition, Personal Setup enables
you to individually control the red,
green, and blue video content in the
image. See “Setting Red, Green, and
Blue Values,” later in this chapter,
for instructions.

23

4 Changing Display Settings

HP Pavilion Multimedia Displays

Adjusting the
Brightness
and Contrast

You can change the display’s
brightness or contrast quickly by
pressing the brightness or contrast
button on the front panel. (You can
also adjust the brightness and
contrast through the OSD main window
as described in the next section,
“Using the OSD Main Window.”)
Brightness adjusts the black level,
while contrast adjusts the difference
between the dark and light parts of
the image.

Adjust the brightness level so that
black items on the screen appear
black. Then adjust the contrast for
the most comfortable viewing.

24

To adjust the brightness or contrast

1. Press the brightness or contrast

button on the front panel to open
the brightness or contrast
adjustment window.

50

2. Press the + or – button to increase

or decrease the setting from its
current position.

3. When the brightness or contrast is

at the desired level, press the
brightness or contrast button again
to close the adjustment window.

4 Changing Display Settings

HP Pavilion Multimedia Displays

(Alternatively, wait five seconds
for the window to close
automatically.)

Using the OSD Main
Window

The OSD main window enables you to
make changes to a variety of display
settings. You open the window by
pressing the Select button when no
other OSD windows are displayed on the
screen.

In the OSD main window, you select
icons for the settings you want to
change:

Select the brightness icon to adjust
the black level in the image.

Select the contrast icon to adjust
the level of difference between light
and dark areas of the image.

Select the horizontal size icon to
adjust the horizontal size of the
image.

Select the horizontal position icon
to adjust the horizontal position of
the image.

English

Select the vertical size icon to
adjust the vertical size of the
image.

Select the vertical position icon to
adjust the vertical position of the
image.

25

4 Changing Display Settings

HP Pavilion Multimedia Displays

Select the pincushion icon to adjust
any tapering or bowing of the sides
of the image.

Select the trapezoid icon to adjust
distortion where the top of the image
is larger or smaller than the bottom
of the image.

Select the color temperature icon to
adjust the color temperature or white
balance of the image. See the next
section, “Choosing the Color
Temperature,” for instructions.

(M70 display only) Select the degauss
icon to degauss the display and
restore image quality.

(M70 display only) Select the
rotation icon to adjust the angle of
the image.

(M70 display only) Select the pin
balance icon to balance any bowing in
the sides of the image.

(M70 display only) Select the
parallelogram icon to square the
image.

Select the factory reset icon to
return size and position settings to
their original factory values. (If
you’re using a nonstandard screen
resolution, this feature returns the
display to the geometric settings in
effect when the resolution was first
applied. See Chapter 5 for lists of
standard resolutions for each
display.)

26

4 Changing Display Settings

HP Pavilion Multimedia Displays

Select the exit icon to close the OSD
main window and save any changes you
have made.

In most cases, when you select an
icon, an adjustment window appears
below the OSD main window. The
adjustment window contains a control
bar that you shorten or lengthen with
the + or – key. A number next to the
control bar shows the percentage of
the current setting relative to its
maximum value.

English

27

4 Changing Display Settings

HP Pavilion Multimedia Displays

There are some exceptions to this
pattern, however:



Selecting the color temperature
icon opens a window where you can
make additional choices. See the
next section, “Choosing the Color
Temperature,” for instructions.



The degauss, factory reset, and
exit options don’t have adjustment
windows. They take effect
immediately after you select them.

To use the OSD main window

1. When no other OSD windows are

displayed on the screen, press the
Select button on the front of the
display to open the OSD main
window.

1024x768 / 75HZ

28

2. Press the + or – button to move

among the icons in the window.

3. When the icon for the function you

want is highlighted, press the
Select button.

If you selected the degauss,
factory reset, or exit option, it
takes effect immediately.

4 Changing Display Settings

HP Pavilion Multimedia Displays

If you selected another option, an
adjustment window appears for the
option you selected.

1024x768 / 75HZ

50

4. Press the + or – button to change
the current setting.

5. Press the Select button to save
your changes and close the
adjustment window.

6. To close the OSD main
window, select the Exit
icon or wait five seconds
for the window to close
automatically.

Choosing the Color Temperature

The default color settings in
Productivity, Photos/Graphics, and
Gaming modes are optimized for best
results in those environments, but you
can change the color temperature
temporarily when necessary. (If you
need to save color settings for a
particular application, use Personal
Setup mode.)

English

29

4 Changing Display Settings

HP Pavilion Multimedia Displays

In Productivity and Gaming Modes, you
can choose between two settings: 9300K
and 6500K. In Photos/Graphics mode,
you can also choose a third
setting—5000K. This setting
is represented by the camera icon.

In Personal Setup mode, you can choose
colors to suit the color of the
ambient lighting in your environment.
9300K is often used for office
environments or fluorescent lighting.
6500K is often used for incandescent
lighting.

You can also choose to individually
adjust the red, green, and blue (RGB)
values that make up the screen image.
See the next section, “Setting Red,
Green, and Blue Values,” for
instructions.

30

To choose the color temperature

1. In the OSD main window, press
the + or – button to move to
the color temperature icon.

2. Press the Select button to open the
color adjustment window.

4 Changing Display Settings

HP Pavilion Multimedia Displays

1024x768 / 75HZ

9300 6500

3. Press the + or – button to move to
the color temperature option you
want.

4. Press the Select button to select
the color temperature and close the
adjustment window.

Setting Red, Green, and Blue
Values

You may need to make very precise
adjustments to the screen color. For
example, under unique ambient lighting
conditions, you may need to adjust the
screen color so that it more closely
matches the output of your printer.
You can make these adjustments in
Personal Setup mode by individually
setting red, green, and blue (RGB)
values.

English

Make sure to let the display warm up
fully before trying to match colors
precisely. It takes the display about
30 minutes to warm up completely after
being turned on or recovering from a
power-saving state.

31

4 Changing Display Settings

HP Pavilion Multimedia Displays

If you have difficulty getting an
exact color match, reset each color to
its middle value (50%), then readjust
to find the color setting you want.

To set RGB values

1. Press the Mode button, and press
the + or – button to select the
Personal Setup mode.

2. Press the Select button to activate
the Personal Setup mode.

3. Press the Select button again to
open the OSD main window.

4. In the OSD main window, press
the + or – button to move to
the color temperature icon.

5. Press the Select button to open the
color adjustment window.

32

1024x768 / 75HZ

9300 6500

6. In the color adjustment
window, use the + button to

4 Changing Display Settings

HP Pavilion Multimedia Displays

move to the Personal Setup icon.

7. Press the Select button to open the
RGB adjustment window. The Exit
icon is highlighted by default.

English

R
G
B

50
50
50

8. If you want to accept the current
RGB values, press the + or - button
to close the window.

9. To make changes to color values,
press the Select button to move to
the red adjustment bar, then press
the + or - button to adjust the
value.

10. Press the Select button to move to
the green adjustment bar, then
press the + or – button to
adjust†it.

11. Press the Select button to move to
the blue adjustment bar, then press
the + or – button to adjust it.

12. Press the Select button to
move to the exit icon, then
press the + or – button to close
the adjustment window.
(Alternatively, wait five seconds
for the window to close
automatically.)

33

5 Technical
Information

This chapter contains technical
information about the M40, M50, and
M70 displays.

These displays are compatible with IBM
PC, PC/XT, PC/AT, PS/2, and other PC­compatible computers. They are also
compatible with VESA power-management
standards. (See “DPMS Power-Management
Features” at the end of this chapter.)

M40 Display Information

Picture tube 14 in (35.6 cm), 90°

deflection, non­glare, black matrix,
light transmission
57% phosphor P22
medium short, 0.28
mm dot pitch

Maximum
viewable area

270 mm (H) x 200 mm
(V)

10.6 in (H) x 7.8 in
(V)

English

Line
(horizontal)
frequency

Raster
(vertical)
frequency

Power source 100–240 VAC, 50/60

30–49 kHz

50–100 Hz

35

5 Technical Information

HP Pavilion Multimedia Displays

Hz

Maximum power

74 W

consumption
Dot rate 65 MHz
Pedestal Tilt: -5° forward,

12° backward
Swivel: 90° left or

right

36

5 Technical Information

HP Pavilion Multimedia Displays

Dimensions
(W x H x D)

372 x 401 x 395 mm

14.9 x 16.0 x 15.8

in
Net weight 11 kg (24.3 lb)
Operating

Conditions
Temperature
Humidity

5° to 35°C (41° to

95°F )

20% to 80%
Storage

Conditions
Temperature
Humidity

-25° to 55°C (-13°

to 131°F )

20% to 80%, non-

condensing

M40 Video Modes

The display supports the following
industry-standard combinations of
screen resolution and refresh rates.
Other combinations are possible, but
may require adjustments to the image
size and position. (See “Using the OSD
Main Window” in Chapter 4 for
information about making these
adjustments.)

English

Resolution

(dots x

lines)

640 x 480 60 Hz
640 x 480 75 Hz
640 x 480 85 Hz
720 x 400 70 Hz
800 x 600 60 Hz
800 x 600 75 Hz

Vertical

Frequency

37

5 Technical Information

HP Pavilion Multimedia Displays

1024 x 768 60 Hz

CAUTION

Setting the screen resolution/refresh
rate combination higher than 1024 x
768 at 60 Hz can damage the display.

M40 Pin Assignments

The following figure illustrates the
15-pin D-sub male video connector used
by the M40 monitor. The table shows
the pin assignments.

Pin 1
Pin 6
Pin 11

Pin

Number

1 Red video input
2 Green video input
3 Blue video input
4 Ground
5 DDC return
6 Red video return
7 Green video return
8 Blue video return
9 No connect
10 Sync return
11 Ground
12 DDC data (SDA)
13 Horizontal sync
14 Vertical sync
15 DDC data clock (SCL)

Assignment

Pin 5
Pin 10
Pin 15

NOTE

38

Because of a policy of continuous
product improvement, pin assignments

5 Technical Information

HP Pavilion Multimedia Displays

are subject to change without notice.

English

39

5 Technical Information

HP Pavilion Multimedia Displays

M50 Display Information

Picture tube 15 in (38.1 cm), 90°

deflection, non­glare, black matrix,
light transmission
57% phosphor P22
medium short, 0.28
mm dot pitch

Maximum
viewable area

280 mm (H) x 210 mm
(V)
11 in (H) x 8.25 in
(V)

Line

30–54 kHz
(horizontal)
frequency

Raster

50–100 Hz
(vertical)
frequency

Power source 100–240 VAC, 50/60

Hz
Maximum power

90 W
consumption

Dot rate 65 MHz
Pedestal Tilt: -5° forward,

12° backward

Swivel: 90° left or

right
Dimensions

(W x H x D)

372 x 401 x 395 mm

14.9 x 16.0 x 15.8

in

40

5 Technical Information

HP Pavilion Multimedia Displays

Net weight 13 kg (28.6 lb)
Operating

Conditions
Temperature
Humidity

5° to 35°C (41° to
95°F )

20% to 80%

Storage
Conditions

Temperature
Humidity

-25° to 55°C (-13°
to 131°F )

20% to 80%, non­condensing

M50 Video Modes

The display supports the following
industry-standard combinations of
screen resolution and refresh rates.
Other combinations are possible, but
may require adjustments to the image
size and position. (See “Using the OSD
Main Window” in Chapter 4 for
information about making these
adjustments.)

English

Resolution

(dots x

lines)

640 x 480 60 Hz
640 x 480 75 Hz
640 x 480 85 Hz
720 x 400 70 Hz
800 x 600 60 Hz
800 x 600 75 Hz
800 x 600 85 Hz

1024 x 768 60 Hz

Vertical

Frequency

41

5 Technical Information

HP Pavilion Multimedia Displays

CAUTION

Setting the screen resolution/refresh
rate combination higher than 1024 x
768 at 60 Hz can damage the display.

42

5 Technical Information

HP Pavilion Multimedia Displays

M50 Pin Assignments

The following figure illustrates the
15-pin D-sub male video connector used
by the M50 monitor. The table shows
the pin assignments.

English

Pin 1
Pin 6
Pin 11

Pin

Number

1 Red video input
2 Green video input
3 Blue video input
4 Ground
5 DDC return
6 Red video return
7 Green video return
8 Blue video return
9 No connect
10 Sync return
11 Ground
12 DDC data (SDA)
13 Horizontal sync
14 Vertical sync
15 DDC data clock (SCL)

Assignment

Pin 5
Pin 10
Pin 15

NOTE

Because of a policy of continuous
product improvement, pin assignments
are subject to change without notice.

43

5 Technical Information

HP Pavilion Multimedia Displays

M70 Display Information

Picture tube 17 in (43.1 cm), 90°

deflection, non-

glare, light

transmission 52%

phosphor P22 medium

short, 0.28 mm dot

pitch
Maximum

viewable area

320 mm (H) x 240 mm

(V)

12.8 in (H) x 9.6 in

(V)
Line

30–70 kHz
(horizontal)
frequency

Raster

50–120 Hz
(vertical)
frequency

Power source 100–240 VAC, 50–60

Hz
Maximum power

130 W (maximum)
consumption

Dot rate 110 MHz
Pedestal Tilt: -5° forward,

17° backward

Swivel: -45° left or

right
Dimensions

(W x H x D)

408 x 416 x 450 mm

16.3 x 16.6 x 18.0

in

44

5 Technical Information

HP Pavilion Multimedia Displays

Net weight 19 kg (41.9 lb)
Operating

Conditions
Temperature
Humidity

5° to 35°C (41° to
95°F )

20% to 80%, non­condensing

Storage
Conditions

Temperature
Humidity

-25° to 60°C (-13°
to 140°F )

20% to 80%, non­condensing

M70 Video Modes

The M70 display supports the following
industry-standard combinations of
screen resolution and refresh rates.
Other combinations are possible, but
may require adjustments to the image
size and position. (See “Using the OSD
Main Window” in Chapter 4 for
information about making these
adjustments.)

English

Resolution

(dots x

lines)

640 x 480 60 Hz
720 x 400 70 Hz
800 x 600 75 Hz
800 x 600 85 Hz

1024 x 768 60 Hz
1024 x 768 75 Hz
1024 x 768 85 Hz

1280 x 1024 60 Hz

Vertical

Frequency

45

5 Technical Information

HP Pavilion Multimedia Displays

CAUTION

Setting the screen resolution/refresh
rate combination higher than 1280 x
1024 at 60 Hz can damage the display.

46

5 Technical Information

HP Pavilion Multimedia Displays

M70 Pin Assignments

The following figure illustrates the
15-pin D-sub male video connector used
by the M70 display. The table shows
the pin assignments.

English

Pin 1
Pin 6
Pin 11

Pin

Number

1 Red video input
2 Green video input
3 Blue video input
4 Ground
5 No connect
6 Red video return
7 Green video return
8 Blue video return
9 No connect
10 Ground
11 Ground
12 SDA data
13 Horizontal sync
14 Vertical sync
15 DDC data clock (SCL)

Assignment

Pin 5
Pin 10
Pin 15

NOTE

Because of a policy of continuous
product improvement, pin assignments
are subject to change without notice.

47

5 Technical Information

HP Pavilion Multimedia Displays

DPMS Power-Management
Features

The HP Pavilion M40, M50, and M70
displays can recognize power­management signals from VESA DPMS
video adapters, such as those in HP
Pavilion and many other computers.
When the display receives an
appropriate signal, it reduces its
power but remains ready for quick use.
The power light on the front panel
turns amber when the display is in a
power-saving mode.

VESA DPMS video adapters reduce
display power consumption by setting
the horizontal and/or vertical
synchronization signals to inactive.
The display will recover quickly when
the synchronization signals are
reapplied.

48

Standby and Suspend modes offer low
power consumption with rapid recovery,
while Sleep mode offers the lowest
power consumption and a somewhat
slower recovery.

The following table shows the
characteristics of the normal
operating mode and the three power­saving modes.

VESA DPMS Power Management

POWER USED

Hor.

Mode Video

sync
.

Vert
.
sync

M40 M50 M70

5 Technical Information

HP Pavilion Multimedia Displays

.

On ActiveYes Yes 74W 90W 130W

StandbyBlank No Yes <15W <15W <30W

SuspendBlank Yes No <15W <15W <30W

Sleep Blank No No <8W <8W <8W

English

49

6 Regulatory
Information

FCC Statement

This equipment has been tested and
found to comply with the limits for a
Class B digital device pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful
interference in a residential
installation. This equipment
generates, uses, and can radiate radio
frequency energy. If not installed and
used in accordance with the
instructions, it may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a
particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:

English



Reorient or relocate the receiving
antenna.



Move the computer away from the
radio or television.



Plug the computer into a different
electrical outlet, so that the
computer and the radio or

51

WARNING

6 Regulatory Information

HP Pavilion Multimedia Displays

television are on separate
electrical circuits.



Make sure that all your peripheral
devices are also FCC Class B
certified.



Consult your computer dealer,
Hewlett-Packard, or an experienced
radio/TV technician for help.

Hewlett Packard’s system verification
tests were conducted with HP-supported
peripheral devices and HP shielded
cables, such as those you received with
your system. Cables used with this
display must be properly shielded to
comply with FCC requirements.

Changes or modifications not expressly
approved by Hewlett-Packard could void
the user’s authority to operate the
equipment.

52

X-Ray Radiation Notice

When operating, this product emits X­rays; however, it is well shielded and
meets the safety and health
requirements of various countries,
such as the Radiation Act of Germany
and the Radiation Control for Health
and Safety Act of the United States.

Radiation emitted by this product is
less than 0.1 mR/hr (1µSv/hr) at a
distance of 10 centimeters from the
surface of the cathode-ray tube. The
x-ray radiation primarily depends on
the characteristics of the cathode ray
tube and its associated low-voltage
and high-voltage circuitry. Internal

6 Regulatory Information

HP Pavilion Multimedia Displays

controls have been adjusted to ensure
safe operation. Only qualified
personnel should perform any internal
adjustments, as specified in the
service manual for this product.

Replace the cathode-ray tube with an
identical CRT only.

General Notice

The HP Pavilion M40 (except North
American models), M50, and M70
Multimedia Displays have been tested
according to MPR 1990:8 for emission
properties and meet the guidelines as
given by MPR 1990:10 (2.01 – 2.04).

English

NOTE

NOTE

This display is a Class 1 LED product.

As an ENERGY STAR Partner, Hewlett­Packard has determined that this
product meets the ENERGY STAR
guidelines for energy efficiency.
The ENERGY STAR name is a U.S.
Registered Mark of the U.S.
Environmental Protection Agency.

53

DECLARATION OF CONFORMITY

according to ISO/IEC Guide 22 and EN 45014

English

55

6 Regulatory Information

HP Pavilion Multimedia Displays

Manufacturer’s Name:
Manufacturer’s Address:

Declares, that the products
Product Names:

Displays

Model Numbers:
Conform to the following Product Specifications:
Safety:

A2, A3

Ergonomics:

EMC:

kV AD

Signal Lines,

Issue 2

Supplementary Information

The products herewith comply with the requirements of the
following Directives and carry the CE marking accordingly:

93/68/EEC)

1) The Products were tested in a typical configuration with a
Hewlett-Packard Personal Computer and peripherals.

2) These Devices comply with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) the devices may
not cause harmful interference, and (2) the devices must accept
any interference received, including interference that may
cause undesired operation.

IEC 950:1991 + A1, A2, A3 / EN 60950:1992 + A1,

ZH1/618
ISO 9241-3
MPR II: 1990 (except M40 in North America)

CISPR 22:1993 / EN 55022:1994 - Class B
EN 50082-1:1992 - Generic Immunity

FCC Title 47 CFR, Part 15 Class B2) / ICES-003,

AS / NZS 3548:1992 / CISPR 22:1993 Class B

- the EMC Directive 89/336/EEC (including 93/68/EEC)

- the Low Voltage Directive 73/23/EEC (including

Hewlett-Packard Company
10500 Ridgeview Ct.

Cupertino, CA 95015
USA

HP Pavilion M40, M50, and M70 Multimedia

D5269A, D5258A, D5259A

1)

IEC 801-2:1991/ prEN 55024-2:1992 - 4 kV CD, 8

IEC 801-3:1984/ prEN 55024-3:1991 - 3 V/m
IEC 801-4:1988/ prEN 55024-4:1992 - 0.5 kV

1 kV Power Lines

1)

:

Cupertino, CA June, 1997

Manager

For Regulatory Compliance Information ONLY, contact:
Australian Contact:

Australia Ltd., 31-41 Joseph Street, Blackburn, Victoria 3130,
Australia

Product Regulations Manager, Hewlett-Packard

Robert B. Smith/Quality

56

6 Regulatory Information

HP Pavilion Multimedia Displays

European Contact

Office or Hewlett-Packard GmbH, Department HQ-TRE Standards
Europe, Herrenberger Straße 130, D-71034 Böblingen
(FAX: + 49-7031-14-3143)

USA Contact:

10500 Ridgeview Ct.,
Cupertino, CA 95015-4010 (Phone: [phone])

: Your local Hewlett-Packard Sales and Service

Product Regulations Manager, Hewlett-Packard, HPD,

English

57

6 Regulatory Information

HP Pavilion Multimedia Displays

58