Polk Audio LC265I-IP, LC80I-IP User Manual
THIS DOCUMENT APPLIES TO LC265i-IP AND LC80i-IP PRODUCTS
Cutsheet for LC265i-IP/LC80i-IP
World’s First Active High Performance IP Addressable Loudspeakers
Polk Audio LCi-IP Ultra High Performance In-Wall/ In-Ceiling Loudspeakers are the world’s first active Internet Protocol-ready Loudspeakers. They were created for IP networked systems (such as the ground-breaking NetStreams
amplifiers eliminate remote amplifiers connected via hundreds of feet of performance-robbing speaker wires. The built-in Digital
Signal Processor (DSP) and supplied Room Correction Software (the Performance Optimization Wizard
to be optimized for maximum performance in any room. While the LCi-IP Series provides the greatest functionality when used
within an IP-based system, these speakers are also compatible with any analog distributed audio system.
LC265i-IP Hardware (included)
• One LC265i-IP speaker
• Performance Optimization Wizard – CD-ROM
• Euro-style (Phoenix) power supply connector
• Mounting template
• Paint mask
• Weather-resistant aluminum grille
and stainless steel hardware
•LCi-IP manual
• Laminated configuration setup card
• Registration card
Note: If you are setting up LCi-IP speakers to be controlled via an
IP-network such as NetStreams
is sold separately, from NewStreams™. The network card will control up to
one pair of speakers.
Important Note: If anything is missing or damaged, or if your LCi-IP speaker
fails to operate, notify Polk Audio Installer Support Services immediately at
800-377-7655. Hours: Mon-Fri, 9am - 5:30pm EST.
™
Digilinx™, purchase a network card, which
Cutout
Dimension
19 1/4"
(48.9 cm)
™
DigiLinx™system). Integrated digital
™
) enable every LCi-IP speaker
Accessories (not included)
• Performance Enclosure for exact volume enclosure performance
in pre-build installations. Improves bass performance and
sound isolation. Model number: ENCL265.
• Speaker-level-to-line-level transformer, such as the PAC SNI-35.
(For analog installations only. Powers up to 2 each LC265i-IP speakers.)
• SPS-1 Power Supply (a power supply is required).
LC265i-IP Performance Enclosure Dimensions
55 5/8" H x 14" W x 3 3/8" D (141.3cm x 35.6cm x 8.6cm)
Total
Cutout
Dimension
7 1/4"
(18.4 cm)
Depth
3 9/16"
(9.1 cm)
LC265i-IP Dimensions
Overall Height 20 7/8" (55.5cm)
Overall Width 8 1/2" (30.4cm)
Available Finish: Paintable White
www.PolkAudio.com / 800.377.7655 (USA & Canada) / 410.358.3600 (Worldwide) 1
LC80i-IP Hardware
• One LC80i-IP speaker
• Performance Optimization Wizard – CD-ROM
• Euro-style (Phoenix) power supply connector
• Mounting template
• Paint mask
• Weather-resistant aluminum grille
and stainless steel hardware
•LCi-IP manual
• Laminated configuration setup card
• Registration card
Note: If you are setting up LCi-IP speakers to be controlled via an
IP-network such as NetStreams
™
Digilinx™, purchase a network card, which
is sold separately, from NewStreams™. The network card will control up to
one pair of speakers.
Important Note: If anything is missing or damaged, or if your LCi-IP speak-
er fails to operate, notify Polk Audio Installer Support Services
immediately at 800-377-7655.
Accessories (not included)
• Performance Enclosure for exact volume enclosure performance
in pre-build installations. Improves bass performance and
sound isolation. Model number: ENCL 80IP.
• Speaker-level-to-line-level transformer, such as the PAC SNI-35.
(For analog installations only. Powers up to 4 each LC80i-IP speakers.)
• SPS-1 Power Supply (a power supply is required).
Cutout
Dimension
9 7/16"
(23.9 cm)
Total
Depth
7 7/16"
(18.9 cm)
LC80i-IP Dimension
Outer Diameter 10 3/4" (27.3cm)
Available Finish: Paintable White
LC80i-IP Performance Enclosure Dimensions
20 5/8" H x 13" W x 9" D (51.8cm x 33.0cm x 22.9cm)
Power Supply
The SPS-1 power supply was specifically designed to produce clean,
reliable power to ensure that all Polk Audio LCi-IP loudspeakers perform
to their maximum capabilities. All output connectors are protected
against short circuit and over current.
Specifications
Output
Voltage 48VDC
Current 8A (Max continuous)
Input
Voltage Range 100-240 VAC Nominal Auto Switching
Frequency 50-60Hz
Current Draw 8A (120V)
3.5A (240V)
Dimensions
Width 4.9" (125mm)
Height 3.1" (79mm) , 3 11/16"(93.6mm) with feet
Length 14" (358mm)
Shipping Weight 8.4lbs (4kgs)
Protection Thermal, short circuit,current/power overdraw
Fuse Replacement T8AH500V
2 Polk Audio Custom Install Product: LC265i -IP, LC80i -IP
IEC Socket
This is a standard
IEC socket.
Power Connectors
For optimum performance, we recommend using 14-gauge,
4-conductor wire between the power supply and each
amplifier (see the LCi-IP manual for other wiring options).
Note: Leave at least 2-3 inches
of clearance on the sides and
top of the power supply.
Capabilites
SPS-1 will power 2 LC265i-IP speakers or 4 LC80i-IP speakers.
Loading...