Polk Audio LC265i User Manual

THIS DOCUMENT APPLIES TO LC265i-IP AND LC80i-IP PRODUCTS
Cutsheet for LC265i-IP/LC80i-IP
World’s First Active High Performance IP Addressable Loudspeakers
Polk Audio LCi-IP Ultra High Performance In-Wall/ In-Ceiling Loudspeakers are the world’s first active Internet Protocol-ready Loud­speakers. They were created for IP networked systems (such as the ground-breaking NetStreams amplifiers eliminate remote amplifiers connected via hundreds of feet of performance-robbing speaker wires. The built-in Digital Signal Processor (DSP) and supplied Room Correction Software (the Performance Optimization Wizard to be optimized for maximum performance in any room. While the LC
i-IP Series provides the greatest functionality when used
within an IP-based system, these speakers are also compatible with any analog distributed audio system.
LC265i-IP Hardware (included)
• One LC265i-IP speaker
• Performance Optimization Wizard – CD-ROM
• Mounting template
• Paint mask
• Weather-resistant aluminum grille and stainless steel hardware
i-IP manual
•LC
• Laminated configuration setup card
• Registration card
Note: If you are setting up LCi-IP speakers to be controlled via an IP-network such as NetStreams™ Digilinx™, purchase a network card, which is sold separately, from NewStreams™. The network card will control up to one pair of speakers.
Important Note: If anything is missing or damaged, or if your LCi-IP speaker fails to operate, notify Polk Audio Installer Support Services immediately at 800-377-7655. Hours: Mon-Fri, 9am - 5:30pm EST.
Cutout
Dimension
19 1/4"
(48.9 cm)
DigiLinx™system). Integrated digital
) enable every LCi-IP speaker
Accessories (not included)
• Performance Enclosure for exact volume enclosure performance e-build installations. Impr
in pr sound isolation. Model number: ENCL265.
• Speaker-level-to-line-level transformer, such as the PAC
(For analog installations only
• SPS-1 Power Supply (a power supply is required).
oves bass per
. Powers up to 2 each LC265
formance and
SNI-35.
i-IP speakers.)
LC265i-IP Performance Enclosure Dimensions
55 5/8" H x 14" W x 3 3/8" D (141.3cm x 35.6cm x 8.6cm)
.PolkAudio.com
www
Cutout
Dimension
7 1/4"
(18.4 cm)
LC265i-IP Dimensions
Overall Height Overall Width 8 1/2" (30.4cm)
vailable Finish: Paintable White
A
/ 800.377.7655 (USA & Canada) / 410.358.3600 (W
20 7/8" (55.5cm)
Total
Depth
3 9/16"
(9.1 cm)
orldwide)
1
LC80i-IP Hardware
• One LC80i-IP speaker
• Performance Optimization Wizard – CD-ROM
• Euro-style (Phoenix) power supply connector
• Mounting template
• Paint mask
• Weather-resistant aluminum grille and stainless steel hardware
i-IP manual
•LC
• Laminated configuration setup card
• Registration card
Note: If you are setting up LCi-IP speakers to be controlled via an IP-network such as NetStreams™ Digilinx™, purchase a network card, which is sold separately, from NewStreams™. The network card will control up to one pair of speakers.
Important Note: If anything is missing or damaged, or if your LCi-IP speak- er fails to operate, notify Polk Audio Installer Support Services immediately at 800-377-7655.
Accessories (not included)
• Performance Enclosure for exact volume enclosure performance in pre-build installations. Improves bass performance and sound isolation. Model number: ENCL 80IP.
• Speaker-level-to-line-level transformer, such as the PAC SNI-35. (For analog installations only. Powers up to 4 each LC80i-IP speakers.)
• SPS-1 Power Supply (a power supply is required).
Cutout
Dimension
9 7/16"
(23.9 cm)
Total
Depth
7 7/16"
(18.9 cm)
LC80i-IP Dimension
Outer Diameter 10 3/4" (27.3cm)
Available Finish: Paintable White
LC80i-IP Performance Enclosure Dimensions
20 5/8" H x 13" W x 9" D (51.8cm x 33.0cm x 22.9cm)
LC265i-IP Specifications
PERFORMANCE
OVERALL FREQ. RESPONSE 20Hz-27kHz
FREQ. RESPONSE -3DB LIMIT 35Hz-27kHz
ANALOG AUDIO SIGNAL VOLTAGE INPUT (LINE-LEVEL) FULL OUTPUT 2V RMS
AMPLIFIER SNR
ARE UPGRADABLE YES
FIRMW
MID-BASS DRIVER 1–6.5"(16.5CM) MINERAL POLYPROPYLENE
CONE, RUBBER SURROUND;
WOOFER 1–6.5
PROPYLENE CONE WITH 1.5
TWEETER 1" (2.5CM) RING RADIATOR IN SWIVEL MOUNT
OUTSIDE DIMENSIONS 8 1/2" X 20 7/8" (21.59CM X 53.04CM)
CUTOUT DIMENSIONS 7 1/4" X 19 1/4" (18.42CM X 48.90CM)
MOUNTING DEPTH (WITH 1/2" DRYWALL) 3 1/16" (7.78CM)
ALLED WEIGHT 8.7 LBS (3.9kg)
INST
SHIPPING WEIGHT 11.6 LBS (5.3kg)
"(16.5CM) AERATED POLY-
POWER CONTINUOUS RATINGS
200W speaker with < 0.5% THD+N (25W tweeter 4 Ohms, 75W mid 8 Ohms, 100W woofer 8 Ohms)
POWER REQUIREMENTS PER SPEAKER
VOLTAGE INPUT 48VDC
CURRENT DRAW 4.5A MAXIMUM
> 90DB
" VOICE COIL
LC80i-IP Specifications
PERFORMANCE
OVERALL FREQ. RESPONSE
FREQ. RESPONSE -3DB LIMIT
ANALOG AUDIO SIGNAL VOLTAGE INPUT (LINE-LEVEL) FULL OUTPUT 2V RMS
AMPLIFIER SNR > 90DB
ARE UPGRADABLE YES
FIRMW
MID-BASS DRIVER
TWEETER
OUTSIDE DIMENSIONS 10 3/4" DIA (27.3CM)
CUTOUT DIMENSIONS 7 3/8" DIA (18.7CM)
MOUNTING DEPTH (WITH 1/2" DRYWALL) 6 15/16" (17.6CM)
ALLED WEIGHT 4.8 LBS (2.2kg)
INST
SHIPPING WEIGHT 6.8 LBS (3.1kg)
1–8"(20.3CM) COMPOSITE POLYPROPYLENE
CONE, RUBBER SURROUND
1"(2.5CM) RING RADIATOR IN SWIVEL MOUNT
POWER CONTINUOUS RATINGS
100W speaker with < 0.5% THD+N (25W tweeter 4 Ohms, 75W mid 4 Ohms)
POWER REQUIREMENTS PER SPEAKER
VOLTAGE INPUT 48V OR 28VDC
CURRENT DRAW 2.3A
3.8A @ 28V MAXIMUM
25Hz-27kHz
40Hz-27kHz
@ 48V, OR
Power Supply
The SPS-1 power supply was specifically designed to pr reliable power to ensure that all Polk Audio LCi-IP loudspeakers perform to their maximum capabilities. All output connectors are protected against shor
t circuit and over current.
Specifications
Output
Voltage 48VDC
ent
r
Cur
Input
Voltage Range 100-240 VAC Nominal Auto Switching Frequency 50-60Hz Current Draw 8A (120V)
Dimensions
Width 4.9" (125mm) Height 3.1" (79mm) , 3 11/16"(93.6mm) with feet Length 14" (358mm) Shipping Weight 8.4lbs (4kgs) Protection Thermal, short circuit,current/power overdraw
Fuse Replacement T8AH500V
2 Polk Audio Custom Install Pr
8A (Max continuous)
3.5A (240V)
oduct: LC265
i -IP
, LC80
oduce clean,
IEC Socket
This is a standard IEC socket.
i -IP www
Power Connectors
For optimum performance, we recommend using 14-gauge, 4-conductor wir amplifier (see the LC
Note: Leave at least 2-3 inches of clearance on the sides and top of the power supply.
e between the power supply and each
i-IP manual for other wiring options).
Capabilites
SPS-1 will power 2 LC265i-IP speakers or 4 LC80i-IP speakers.
LC265i-IP and LC80i-IP Specifications
INHERENT DELAY
INHERENT DELAY FOR EACH SPEAKER IS:
-2.5 MILLISECONDS -4.4 MILLISECONDS
ANY OTHER DELA
Y IS FROM THE MUL
PROTECTION CIRCUITRY
Thermal, short-circuit, current overdraw, clipping compr
esser/limiter
TI-ROOM AUDIO VISUAL (MRA
everse polarity
, r
CONTROLS AND ADJUSTMENTS
mance Optimization Wizard Program)
for
(Per
COMPUTER REQUIREMENTS
OPERATING SYSTEM WINDOWS XP
V).
.PolkAudio.com
USB PORT 5-WIRE USB 1.1 CONNECTOR HARD DRIVE 5 MEGABYTES
REQUIRED SPEAKER CONNECTIONS
TO CONNECT YOUR COMPUTER TO THE SPEAKER, YOU HAVE TWO OPTIONS:
1. USB PORT (ANALOG USE ONLY)
2. ETHERNET JACK WITH NETWORK DECODER CARD (SOLD SEPARATELY).
/ 800.377.7655 (USA & Canada) / 410.358.3600 (W
orldwide)
3
LC265i-IP/LC80i-IP Specifications (continued)
Connections
ire Recommendations
W
Network Line
Shielded Cat5e or Cat6 cable with RJ-45 connectors. Wiring term­ination convention should be the same at both ends of the cable.
COMM Line
Shielded Cat5e or Cat6 cable with RJ-45 connectors. Wiring term­ination convention should be the same at both ends of the cable.
Analog Line
Low capacitance multi-stranded RCA shielded cable, or speaker wire with speaker-level-to-line-level transformer (such as the PAC
USB Connection
USB 1.1, 5-wire, USB to mini-USB cable.
Power Lines
These recommendations are for all connections from the power supply to each speaker. 14/4 is recommended for all applications. If this is not possible, refer to this chart:
Wire length Wire gauge/
<50’ 16/2
50-100’ 16/4
>100’ 14/4
SNI-35).
# of Conductors
Recommended Configuration
LCi-IP Performance Optimization WizardSMProgram
Polk Audio provides the Performance Optimization Wizard on CD-ROM. This program enables you to optimize the perform­ance characteristics of Polk Audio LCi-IP speakers specifically to their location in a given room and to the physical characteristics of that room. You can also download the Performance Optimization Wizard from our website
(www.polkaudio.com/downloads/po-wizard.exe ).
Walking Through the Room Optimization Choices
• This program can be used for installing and setting up in-wall or in-ceiling LCi-IP speakers and asks basic configuration and room environment questions (figure1).
SM
Network Decoder Card
See Owner’s Manual for installation instructions
Amplifier Connections
ostyle
Eur
RCA
COMM
Network In
LCi-IP speakers are designed for use with analog and digital systems. The speakers per
fers gr
mode of
form equally well in either mode, though the digital
eater contr
ol functionality
. Speaker adapters are available for legacy analog systems wher is already run, allowing connection to RCA input of the speaker.
(Phoenix)
Power In
weeter
T
-level-to-line-level e speaker wir
Figure 1
Depending on the speaker you’re installing, its location and the
oom, you may be asked for a series of measur
r
ements, including the height of the listening room’s ceiling, distances from walls, ceiling and floor to the speaker(s), as well as ver of speakers r
elative to the listening ar
tical and horizontal angles
ou may also be asked to
ea. Y provide measurements for the height, width, depth and center of the listening ar
ea (see the LC
i-IP Owner’
s Manual for more).
Factory Support
For pr
oduct suppor
t visit our website at www or Polk Audio Customer Service: 1-800-377-7655 (Outside US & Canada: 410-358-3600) Monday-Friday polkcs@polkaudio.com
For more information on the LC
e
http://www.polkaudio.com/downloads/manuals/home/ LCi-265IP LCi-80IP_Manual.pdf.
i-265IP and LCi-80IP log onto
.polkaudio.com
, 9:00 AM-6:00 PM EST
,
4 Polk Audio Custom Install Pr
oduct: LC265
i -IP
, LC80
i -IP
Loading...