26”- 46" HD Widescreen Commercial LCD TV
TECHNICIAN’S GUIDE
Your LCD TV may look slightly different from the one pictured above.
Table of Contents
Important Safety Instructions ................................................................................ 2
Technician Setup..................................................................................................... 4
Enseo Set Top Box Operation................................................................................ 6
Troubleshooting ...................................................................................................... 7
- 1 -
Important Safety Instructions
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electrocution.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance. For TVs with a built-in DVD player:
CAUTION: Laser radiation when open. Do not stare into beam.
POWER SUPPLY:
Connect the supplied adapter to the side of the DVD player (if equipped) or back of the TV in the slot
marked “Power In”. Plug the two-prong end of the power cord to a 110-220 volt electrical outlet. If
you have difficulty inserting the plug, turn it over and reinsert it. If the unit will not the used for a long
time, disconnect the plug from the outlet. (For TVs with a built-in DVD player)
NOTE:
Before plugging the power cord into an AC outlet, make sure that all input and output device
connections have been made.
CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
Refer to service manual for servicing instructions.
The images in this manual are for reference only and may differ from your model.
- 2 -
Important Safety Instructions
1) Read and follow all directions.
2) Keep these instructions.
3) Heed all warnings.
4) Do not use near water.
5) Clean only with dry cloth.
6) Do not block any ventilation
openings. Maintain well ventilated
conditions around the product, Do
not put product on bed, sofa or anything that blocks ventilation. Install in accordance with the
manufacturer’s instructions.
7) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
8) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. DANGER: Visible laser radiation when open and
interlock failed or defeated. A void direct exposure to
beam.
3. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit. Leave all
servicing to qualified service personnel.
9) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10) Only use attachments/accessories specified by the manufacturer.
11) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
12) Unplug this apparatus during lightning storms or when unused for long periods of time.
13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such
as vases, shall be placed on the apparatus.
Note: Do not touch the LCD screen. In the event that an electric shock is transmitted, the
screen could be damaged.
Copyright Protection (For TVs with a built-in DVD player)
This product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
- 3 -
Technician Setup
This television is designed for commercial use and some settings can be controlled via the
Technician’s Menu. To access this menu and these settings, please follow the procedures below.
1. Turn down the television volume to the minimum level.
2. Use the number buttons to enter the PIN. The Technician’s Menu will then appear as shown.
Please consult your Polaroid sales representative for a PIN number.
Within this menu, press the ▲▼ button to select item and press the ◄ or ► button to enter the
setup menu; press the Exit button to exit the menu.
Technician Setting
Press the ▲▼ button to select Technician
Setting and press the ◄ ► button to enter
the setup menu. Within this menu, press the
▲▼ button to select items and press the
Enter button to set. Press the Exit button to
exit the menu.
- 4 -
Technician Setup (Continued)
Application Mode
Press the ▲▼ button to select Application
Mode and press the Enter button to enter the
select the application mode (VOD): NXTV,
OnCommand, OnCommand/Enseo, HSI, No
VOD, LodgeNet or LodgeNet/Enseo. Press
the Exit button to exit the menu.
Software Version
Press the ▲▼ button to select Software Version
and press the Enter button to display the
software version information on the screen. Press
the Exit button to exit the menu.
Note: Software Version information will change
after firmware updates.
Reset
Press the ▲▼ button to select Reset and press
the Enter button to reset all the settings of
technician menu to default status. Press the Exit
button to exit the menu.
- 5 -
Enseo Set Top Box Operation
Your TV may have come equipped with an optional Enseo set top box for hospitality Video on
Demand (VOD) support. For models equipped with an Enseo set top box, please refer to the
following.
Enseo Set Top Box Installation:
Refer to the figure and the steps below to install the Enseo set top box to the unit:
1. Open the back cover on the left rear panel of the unit.
2. Carefully insert the bracket into the appropriately sized cavity on the back of the TV and lock it
using the screws.
3. Carefully insert the Enseo set top box into the appropriately sized cavity on the bracket and lock
with the screws.
4. Plug one end of the communication cord into the PPV jack on the Enseo set top box.
5. Plug the other end of t he communication cord into the RJ-11 jack on the unit. The television has
are two RJ-11 jacks with the same functionality, one on the left rear panel and the other on the
right rear panel; either can be used.
6. Plug one end of the power supply cord into the DC IN jack on the Enseo set top box.
7. Plug the other end of the power supply cord into the either of the DC OUT jacks on the unit.
8. Close the back cover.
Note: Before installing the Enseo Set Top Box, make sure that the television is unplugged
and powered off.
- 6 -
Troubleshooting
Note: if a hospitality VOD system is in use, please ensure all VOD functionality is working properly,
contacting the VOD provider’s technical support if necessary, prior to following the television
troubleshooting procedures below.
Many simple problems can quickly be solved using the procedures below. Please follow the procedures below
prior to contacting Polaroid customer service. If you suspect something wrong with this unit, immediately turn the
power off and disconnect the power connector from the unit. Never try to repair the unit yourself because it is
dangerous to do so.
SYMPTOM CHECK ITEM
There is no display on the screen.
There is no sound.
There is no picture or picture moves
up and down.
The unit can’t play discs.
The unit does not continue to play
discs or plays the same section
repeatedly.
The remote control does not work.
Make sure the unit is turned on and all connections are correct. Ensure
that the input selected is active.
Make sure the unit is turned on and all connections are correct.
Make sure the volume is not turned down or muted.
Make sure the sound setup is correct.
In DVD mode, make sure disc is not dirty or warped.
Make sure all connections are correct.
Make sure the unit is in correct video mode.
Make sure disc is loaded in correctly.
Make sure disc is not dirty or warped.
Make sure the region code is the same as region code of DVD disc.
Make sure water condensation has not occurred. If it occurs, take out the
disc and leave the unit on for at least one hour .
Make sure disc is not dirty or damaged.
Make sure the unit is not in any repeat status.
Replace the batteries in the remote control with fresh batteries.
Make sure there are no obstructions between the remote control and the
television.
Make sure the remote control is pointing at the television.
Make sure the batteries are correctly installed in the remote control.
Other Notes:
Static electricity, lightning, power outages or brownouts and other external interference may cause the television to
behave abnormally . Should this occur, unplug the television power cord from the outlet, wait 60 seconds, and then
plug it in again to reset the unit. If the problem persists, then please disconnect the power and consult a qualified
technician.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. © 1992 -1997 Dolby Laboratories, Inc.
All rights reserved.
is a trademark of SRS Labs, Inc.
TruSurroundXT technology is incorporated under license from SRS Labs, Inc.
- 7 -
- -
7
Online Version 20070918
Loading...