Read this manual carefully. It contains important safety information.
Operation is prohibited for those under 16 years of age.
This is an adult vehicle only.
Page 2
WARNING
The engine exhaust from this product contains chemicals
known to the State of California to cause cancer, birth defects
or other reproductive harm.
A card containing important ATV safety information should be
attached to the owner's manual on the next page. If you cannot
locate this card, or if it has been removed, please call 1-800342-3764 for assistance.
Page 3
The text is printed on 100% recycled
with 40% post-consumer waste (PCW).
Page 4
PMS 419
WARNING
Improper vehicle use can result in SEVERE INJURY or DEATH.
ALWAYS USE
AN APPROVED
HELMET AND
PROTECTIVE GEAR
FOR DRIVER
AND PASSENGER
NEVER USE
ON PUBLIC
ROADS
NEVER CARRY
MORE THAN
1 PASSENGER
NEVER USE
WITH DRUGS
OR ALCOHOL
NEVER operate:
without proper ATV training or instruction
at speeds too fast for your skills or the conditions
on public roads - a collision can occur with another vehicle
with a passenger unless passenger seat is securely in place
THE OPERATOR MUST ALWAYS:
use proper riding techniques to avoid vehicle overturns on hills
and rough terrain and in turns
avoid paved surfaces - pavement may seriously affect handling
and control
reduce speed and use extra caution at all times when carrying a
passenger - dismount passenger when conditions require
make sure passenger reads and understands this label and
passenger safety label
READ OWNER'S MANUAL.
FOLLOW ALL INSTRUCTIONS AND WARNINGS.
For your nearest Polaris dealer,
call 1-800-POLARIS
or visit www.polarisindustries.com
Polaris Sales Inc., 2100 Hwy 55
Medina, MN 55340
Phone 1-888-704-5290
Part No. 9922730 Rev 01
Printed in USA
*9922730 *
Page 5
WELCOME
Thank you for purchasing a POLARIS vehicle, and welcome to our
world-wide family of POLARIS owners. We proudly produce an exciting line of utility and recreational products.
• Snowmobiles
• All-terrain vehicles (ATVs)
• RANGER
• Victory Motorcycles
• Low emission vehicles (LEVs)
We believe POLARIS sets a standard of excellence for all utility and
recreational vehicles manufactured in the world today. Many years of
experience have gone into the engineering, design, and development of
your POLARIS vehicle, making it the finest machine we’ve ever produced.
For safe and enjoyable operation of your vehicle, be sure to follow the
instructions and recommendations in this owner’s manual. Your manual
contains instructions for minor maintenance, but information about
major repairs is outlined in the POLARIS Service Manual and should be
performed only by a factory certified Master Service Dealer
technician.
Your POLARIS dealer knows your vehicle best and is interested in your
total satisfaction. Be sure to return to your dealership for all of your service needs during, and after, the warranty period.
We also take great pride in our complete line of apparel, parts and accessories, available through our online store at www .purepolaris.co m. Have
your accessories and clothing delivered right to your door!
®
utility vehicles
®
®
(MSD)
1
Page 6
POLARIS, THE WAY OUT and SPORTSMAN are registered trademarks of POLARIS
Industries Inc.
Copyright 2010 POLARIS Sales Inc. All information contained within this publication
is based on the latest product information at the time of publication. Due to constant
improvements in the design and quality of production components, some minor discrepancies may result between the actual vehicle and the information presented in this publication. Depictions and/or procedures in this publication are intended for reference use
only. No liability can be accepted for omissions or in acc uracies. Any reprinting or reuse
of the depictions and/or procedures contained within, whether whole or in part, is
expressly prohibited.
The original instructions for this vehicle are in English. Other languages are provided as
translations of the original instructions.
The following signal words and symbols appear throughout this manual
and on your vehicle. Your safety is involved when these words and symbols are used. Become familiar with their meanings before reading the
manual.
The safety alert symbol indicates a potential personal injury hazard.
WARNING
A WARNING indicates a hazardous situation which, if not avoided, may result in
death or serious injury.
CAUTION
A CAUTION indicates a hazardous situation which, if not avoided, may result in
minor or moderate injury.
NOTICE
A NOTICE indicates a situation that may result in property damage.
The Prohibition Safety Sign indicates an action NOT to take in order
to avoid a hazard.
The Mandatory Action Sign indicates an action that NEEDS to be
taken to avoid a hazard.
4
Page 9
INTRODUCTION
WARNING
Failure to heed the warnings and safety precautions contained in this manual
can result in severe injury or death. A POLARIS ATV is not a toy and can be
hazardous to operate. This vehicle handles differently than other vehicles, such
as motorcycles and cars. A collision or rollover can occur quickly , even during
routine maneuvers like turning, or driving on hills or over obstacles, if you fail to
take proper precautions.
• Read this owner’s manual. Understand all safety warnings, precautions and
operating procedures before operating a POLARIS ATV. Keep this manual
with the ATV.
• Never operate an ATV without proper instruction. Take a training course.
• This vehicle is an ADULT VEHICLE ONL Y. Operation is prohibited for anyone
under 16 years of age.
• Never permit a guest to operate the ATV unless the guest has read this
manual and all product labels and has completed a certified safety training
course.
5
Page 10
INTRODUCTION
####
VIN
Engine Serial Number
Key
Number
550850
Vehicle Identification Numbers
Record your vehicle's identification numbers and key number in the
spaces provided. Remove the spare key and store it in a safe place. An
ignition key can be duplicated only by ordering a POLARIS key blank
(using your key number) and mating it with one of your existing keys.
The ignition switch must be replaced if all keys are lost.
Vehicle Model Number: __________________________________________________________
ATV safety training is a top priority for POLARIS. POLARIS strongly
encourages you and any family members who will be riding the ATV to
take a training course.
If you purchased a new POLARIS A T V in the United States, your dealer
provided information about the authorized ATV RiderCourse
available to you and your eligible family members. This training is
included in the purchase price of your ATV. You were also provided
with printed materials that explain safe operating procedures. You
should review this information on a regular basis.
If you purchased a used POLARIS ATV in the United States, you can
sm
enroll in the ATV RiderCourse
for a fee. Call ATV Enrollment Express
at (800) 887-2887 or visit www.atvsafety.org.
If you purchased a POLARIS ATV outside the United States, please
contact your dealer or local law enforcement agencies for information
about safety training.
A POLARIS ATV is an off-road vehicle. Familiarize yourself with all
laws and regulations concerning the operation of this vehicle in your
area.
W e strongly advise you to strictly follow the recommended maintenance
program outlined in your owner's manual. This preventive maintenance
program is designed to ensure that all critical components on your vehicle are thoroughly inspected at specific intervals.
FOR MORE INFORMATION ABOUT ATV SAFETY in the United
States, call the Consumer Product Safety Commission at 1-800638-2772, or visit www.cpsc.gov, visit www.atvsafety.org, or call
POLARIS at 1-800-342-3764.
sm
that is
7
Page 12
SAFETY
Helmet
Eye Protection
Gloves
Boots
Long Pants
Long
Sleeves
E
4
051039
0006.31
Safe Riding Gear
Always wear appropriate clothing when riding an ATV. Wear protective
clothing for comfort and to reduce the chance of injury.
Helmet
Wearing a helmet can prevent a severe head injury. Whenever riding a
POLARIS vehicle, always wear a helmet that meets or exceeds established safety standards.
Approved helmets in the USA and Canada bear a U.S. Department of
Transportation (DOT) label.
Approved helmets in Europe, Asia and Oceania
bear the ECE 22.05 label. The ECE mark consists
of a circle surrounding the letter E, followed by the
distinguishing number of the country which has
granted approval. The approval number and serial
number will also be displayed on the label.
8
Page 13
SAFETY
Safe Riding Gear
Eye Protection
Do not depend on eyeglasses or sunglasses for eye protection. Whenever riding a POLARIS vehicle, always wear shatterproof goggles or
use a shatterproof helmet face shield. POLARIS recommends wearing
approved Personal Protective Equipment (PPE) bearing markings such
as VESC 8, V-8, Z87.1, or CE. Make sure protective eye wear is kept
clean.
Gloves
Off-road style gloves with knuckle pads are the best for comfort and
protection.
Boots
The best footwear is a pair of sturdy over-the-calf boots with low heels.
Clothing
Always wear long sleeves and long pants to protect arms and legs.
Riding pants with kneepads and a jersey with shoulder pads provide the
best protection.
Equipment Modifications
We strongly recommend that consumers do not install on a POLARIS
ATV any equipment that may increase the speed or power of the vehicle,
or make any other modifications to the vehicle for these purposes.
The warranty on your POLARIS ATV is terminated if any equipment
has been added to the vehicle, or if any modifications have been made to
the vehicle, that increase its speed or power.
The addition of certain accessories, including (but not limited to) mowers, blades, tires, sprayers, or large racks, may change the handling characteristics of the vehicle. Use only POLARIS-approved accessories, and
familiarize yourself with their function and effect on the vehicle.
9
Page 14
SAFETY
WARNING
Safety Warnings
Failure to operate the ATV properly can result in a collision, loss of control,
accident or overturn, which may result in serious injury or death. Heed all safety
warnings outlined in this section of the owner’s manual. See the OPERATION
section of the owner’s manual for proper operating procedures.
Operating Without Instruction
Operating this ATV without proper instruction
increases the risk of an accident. The operator
must understand how to operate the ATV properly
in different situations and on different types of
terrain.
Beginning and inexperienced operators should
complete the recommended safety training before
operating this vehicle. See page 7.
Never permit a guest to operate the ATV unless the
guest has read this manual and all product labels
and has completed a certified safety training
course.
Age Restrictions
This vehicle is an ADULT VEHICLE ONLY. Operation is prohibited for anyone
under 16 years of age. Never allow anyone under 12 years of age to ride as a
passenger on this 2-up ATV.
Even though a child may be within the recommended age group for operating
some ATVs, he/she may not have the skills, abilities, or judgment needed to
operate or ride on this ATV safely and could be susceptible to accident or injury.
10
Page 15
SAFETY
Safety Warnings
Handling Gasoline
Gasoline is highly flammable and explosive under certain conditions.
• Always refuel with the engine stopped, and outdoors or in a well ventilated
area.
• Do not smoke or allow open flames or sparks in or near the area where
refueling is performed or where gasoline is stored.
• Do not overfill the tank. Do not fill the tank neck.
• If gasoline spills on your skin or clothing, immediately wash it off with soap
and water and change clothing.
Exposure to Exhaust
Engine exhaust fumes are poisonous and can cause loss of consciousness or
death in a short time. Never start the engine or let it run in an enclosed area.
The engine exhaust from this product contains chemicals known to cause
cancer, birth defects or other reproductive harm. Operate this vehicle only
outdoors or in well-ventilated areas.
Failure to Inspect Before Operating
Failure to inspect and verify that the ATV is in safe
operating condition before operating increases the
risk of an accident.
Always inspect the ATV before each use to make
sure it's in safe operating condition.
Always follow all inspection and maintenance
procedures and schedules described in the
owner's manual.
11
Page 16
SAFETY
Safety Warnings
Protective Apparel
Riding in this vehicle without wearing an
approved helmet and protective eyewear
increases the risk of a serious injuries in the
event of an accident.
Operator and passenger must always wear an
approved helmet that fits properly and eye
protection (goggles or face shield).
Carrying a Passenger
Do not carry a passenger until you have at
least two hours of driving experience with this vehicle.
Carrying More Than One
Passenger
Carrying more than one passenger greatly
reduces the operator's ability to balance and
control the ATV, which may result in an
accident or overturn.
Never carry more than one passenger on this
2-up ATV.
Using Alcohol or Drugs
Operating the ATV after consuming alcohol or
drugs could adversely affect operator
judgment, reaction time, balance and
perception.
Never consume alcohol or drugs before or
while operating an ATV.
12
Page 17
Safety Warnings
Operating on Pavement
Operating an ATV on paved surfaces
(including sidewalks, paths, parking lots and
driveways) may adversely affect the
handling of the ATV and could result in loss
of control and accident or overturn.
Avoid operating the ATV on pavement. ATV
tires are designed for off-road use. If it's
unavoidable, travel slowly and avoid sudden
turns or stops.
Operating on Public Roads
Operating this ATV on public streets, roads
or highways could result in a collision with
another vehicle.
Never operate the ATV on any public street,
road or highway, including dirt and gravel
roads. In many states it's unlawful to
operate ATVs on public streets, roads and
highways.
Operating at Excessive
Speeds
Operating the ATV at excessive
speeds increases the operator's risk
of losing control.
Never operate at excessive speeds.
Travel at speeds appropriate for
your skills, your passenger's skills,
and operating conditions.
SAFETY
13
Page 18
SAFETY
Safety Warnings
Physical Control of the ATV
Removing even one hand or foot can reduce
ability to control the vehicle or could cause loss
of balance and ejection from the ATV.
If a person's feet are not firmly planted on the
footrests, they could come into contact with the
wheels or other moving parts and lead to
accident or injury.
Always keep both hands on the handlebars
and both feet on the footrests of the ATV during
operation. A passenger should always be
seated in the passenger seat with both feet on the footrests and both hands on
the passenger grab handles at all times. The passenger should never hold on to
the operator.
Turning Improperly
Turning improperly could cause loss of
traction, loss of control, accident or
overturn.
Always follow proper procedures for
turning as described in the owner's
manual.
Practice turning at slow speeds before
attempting to turn at faster speeds.
Never turn at excessive speed.
Jumps and Stunts
Attempting wheelies, jumps and other
stunts increases the risk of an accident or
overturn.
Never attempt wheelies, jumps, or other
stunts. Avoid exhibition driving.
14
Page 19
Safety Warnings
Improper Hill Climbing
Improper hill climbing could cause loss of control
or overturn. Always follow proper procedures for
climbing hills as described in the owner's manual.
See page 63. Always move the 4X4 switch to
ADC 4X4 before ascending or descending a hill.
Descending Hills Improperly
Improperly descending a hill could cause loss of
control or overturn.
• Always follow proper procedures for traveling
down hills as described in the owner's manual.
See page 65.
• Always descend a hill with the transmission in
forward gear. Do not descend a hill with the
transmission in neutral. Always move the 4X4
switch to ADC 4X4 before ascending or
descending a hill. See page 39.
• Always check the terrain carefully before
descending a hill.
• Shift your weight rearward.
• Never travel down a hill at high speed.
• Avoid traveling down a hill at an angle, which
would cause the vehicle to lean sharply to one
side. Travel straight down the hill when
possible.
SAFETY
Crossing Hillsides
Driving on a sidehill is not recommended.
Improper procedure could cause loss of control
or overturn. Avoid crossing the side of any hill
unless absolutely necessary.
If crossing a hillside is unavoidable, always
follow proper procedures as described in the
owner's manual. See page 64.
Never attempt to turn the ATV around on any
hill until you've mastered the turning technique
(on level ground) as described in the owner's
manual. See page 66.
15
Page 20
SAFETY
>15°
Safety Warnings
Stalling While Climbing a Hill
Stalling, rolling backwards or improperly
dismounting while climbing a hill could cause
an overturn.
• Always maintain a steady speed when
climbing a hill.
• Always move the 4X4 switch to ADC 4X4
before ascending or descending a hill. See
page 39.
If all forward speed is lost:
• Lean forward to keep body weight uphill. A
passenger should also lean uphill.
• Apply the single lever brakes.
• Lock the parking brake when fully stopped.
• Dismount on the uphill side of the vehicle, or on the left if the vehicle is
pointing straight uphill. Have a passenger dismount first, then the operator
may dismount.
• Turn the ATV around and remount, following the procedure described in the
owner's manual. See page 66.
If the ATV begins rolling backwards:
• Keep operator and passenger body weight uphill.
• Never apply engine power.
• Never apply the rear brake while rolling backwards.
• Apply the single-lever brake gradually.
• When fully stopped, apply th e foot brake as well, and then lock the parking
brake.
• Dismount on the uphill side of the vehicle, or on the left if the vehicle is
pointing straight uphill. Have a passenger dismount first, then the operator
may dismount.
• Turn the ATV around and remount, following the procedure described in the
owner's manual. See page 66.
Operating on Steep Hills
Operating on excessively steep hills could
cause an overturn.
Never operate on hills too steep for the ATV or
for your abilities. Never operate the ATV on
hills steeper than 15 degrees.
16
Page 21
Safety Warnings
Operating on Slippery Terrain
Failure to use extra caution when operating
on excessively rough, slippery or loose terrain
could cause loss of traction, loss of control,
accident or overturn.
Do not operate on excessively rough, slippery
or loose terrain until you've learned and
practiced the skills necessary to control the
ATV on such terrain.
Always use extra caution on rough, slippery
or loose terrain.
Operating in Unfamiliar Terrain
Failure to use extra caution when operating
on unfamiliar terrain could result in an
accident or overturn.
Unfamiliar terrain may contain hidden rocks,
bumps, or holes that could cause loss of
control or overturn.
Travel slowly and use extra caution when
operating on unfamiliar terrain. Always be
alert to changing terrain conditions.
Operating Improperly in
Reverse
Improperly operating in reverse could result
in a collision with an obstacle or person.
Always follow proper operating procedures
as outlined in this manual. See page 70.
Before shifting into reverse gear, always
check for obstacles or people behind the ATV.
When it's safe to proceed, back slowly.
SAFETY
17
Page 22
SAFETY
Safety Warnings
Improper Tire Maintenance
Operating this ATV with improper tires or
with improper or uneven tire pressure could
cause loss of control or accident.
Always use the size and type of tires
specified for your ATV.
Always maintain proper tire pressure as
described in the owner's manual and on
safety labels.
Operating Over Obstacles
Improperly operating over obstacles could
cause loss of control or overturn.
Before operating in a new area, check for
obstacles. Avoid operating over large
obstacles such as rocks and fallen trees. If
unavoidable, use extreme caution and
always follow proper operating procedures
as outlined in this manual. See page 69.
Skidding or Sliding
Skidding or sliding can cause loss of control
or overturn (if tires regain traction
unexpectedly).
On slippery surfaces such as ice or loose
gravel, travel slowly and use extra caution
to reduce the chance of skidding or sliding.
Do not operate on excessively slippery
surfaces.
18
Page 23
SAFETY
Safety Warnings
Operating Through Deep Water
Operating the ATV through deep or fastflowing water could cause the tires to float,
causing loss of control or overturn.
Avoid operating the ATV through deep or
fast-flowing water. If it's unavoidable to
enter water that exceeds the
recommended maximum depth (see page
68):
• Travel slowly.
• Balance your weight carefully.
• Avoid sudden movements.
• Maintain a slow and steady forward motion. Do not make sudden turns or
stops, and do not make sudden throttle changes.
Wet brakes may have reduced stopping ability. After leaving water, test the
brakes. Apply them lightly several times while driving. The friction will help dry
out the pads.
Improper Cargo Loading
Overloading the ATV or carrying/towing
cargo improperly may cause changes in
handling, which could cause loss of control
or an accident.
• Never exceed the stated load capacity for
this ATV.
• Cargo should be properly distributed and
securely attached.
• Reduce speed when carrying cargo or
pulling a trailer. Allow a greater distance
for braking.
• Always follow the instructio ns in the owner's manual for carrying cargo or
pulling a trailer. See pages 72-74.
• Always follow the instructions in the owner's manual for operating with a
passenger. See page 60.
19
Page 24
SAFETY
Safety Warnings
Operating on Frozen Bodies of
Water
Operating on frozen bodies of water may
result in serious injury or death if the ATV
and/or riders fall through the ice.
Never operate the ATV on a frozen body of
water unless you have independently
verified that the ice is sufficiently thick to
support the weight and moving force of the
ATV, you and your cargo, together with any
other vehicles in your party. Variances in
snow depth and/or water currents may result
in uneven ice thickness. Always check with
local authorities and residents to confirm ice
conditions and thickness over your entire
route. ATV operators assume all risk
associated with ice conditions on frozen
bodies of water.
Poor Visibility
Operating the ATV in darkness or inclement weather could result in a collision or
accident, especially if operating on a road or street. This A TV is not equipped
with highway-approved lights. Operate this vehicle off-road only. Use caution
and drive at reduced speeds in conditions of reduced visibility such as fog, rain
and darkness. Clean headlights frequently and replace burned out headlamps
promptly.
20
Page 25
SAFETY
Safety Warnings
Operating a Damaged ATV
Operating a damaged ATV can result in an accident. After any overturn or
accident, have a qualified service dealer inspect the entire machine for possible
damage, including (but not limited to) brakes, throttle and steering systems.
Physical Skills
Safe operation of this rider-active vehicle requires good judgement and physical
skills. Persons with cognitive or physical disabilities who operate this veh icle
have an increased risk of overturn and loss of control. Never secure a
passenger to the vehicle or to the operator with a belt, rope or similar device.
Hot Exhaust Systems
Exhaust system components are very hot during and after use of the vehicle.
Hot components can cause burns and fire. Do not touch hot exhaust system
components. Always keep combustible materials away from the exhaust
system. Use caution when traveling through tall grass, especially dry grass.
Unauthorized Use of the ATV
Leaving the keys in the ignition can lead to unauthorized use of the vehicle,
which could result in an accident or overturn. Always remove the ignition key
when the vehicle is not in use.
21
Page 26
SAFETY
2x4
Trip 1
km
mi
RPM
F
E
88
:
88
Reverse Override Warning
AWD Caution
Age 16 Wa rning
Safety Labels and Locations
Warning labe ls have been placed on the vehicle for your protection.
Read and follow the instructions on each label carefully. If any of the
labels shown in this manual differ from the labels on your vehicle,
always read and follow the instructions of the labels on the vehicle.
If an informational or graphic label becomes illegible or comes off, contact your POLARIS dealer to purchase a replacement. Replacement
safety labels are provided by POLARIS at no charge. The part number is
printed on the label.
Reverse Override Warning/AWD Caution
WARNING
Improper use of override
button can lead to loss of
control resulting in severe
injury or death. Do not
activate override while throttle
is engaged. Always apply
throttle gradually while in
reverse.
CAUTION
Do not push switch to engage
4x4 (AWD) if the rear wheels
are spinning. This may cause
severe drive shaft and clutch
damage.
7175512
Age 16 Warning
WARNING
Operating this ATV if you are under the age of 16 increases the chances of
severe injury or death to both operator and passenger.
NEVER operate this ATV if you are under age 16.
22
7175375
Page 27
SAFETY
General Warning
Safety Labels and Locations
General Warning
WARNING
Improper ATV use can result in SEVERE
INJURY or DEATH
ALWAYS USE AN APPROVED HELMET AND
PROTECTIVE GEAR FOR DRIVER AND
PASSENGER
NEVER USE ON PUBLIC ROADS
NEVER CARRY MORE THAN 1 PASSENGER
NEVER USE WITH DRUGS OR ALCOHOL
NEVER operate:
• without proper ATV training or instruction
• at speeds too fast for your skills or the
conditions
• on public roads - a collision can occur with
another vehicle
• with a passenger unless passenger seat is securely in place
THE OPERATOR MUST ALWAYS:
• use proper riding techniques to avoid overturns on hills and rough terrain and
in turns
• avoid paved surfaces - pavement may seriously affect handling and control
• reduce speed and use extra caution at all times when carrying a passenger -
dismount passenger when conditions require
• make sure passenger reads and understands this label and passenger safety
label
LOCATE AND READ OPERATOR’S MANUAL.
FOLLOW ALL INSTRUCTIONS AND WARNINGS.
7175844
23
Page 28
SAFETY
Passenger Warning
Discretionary Warning
Tire Pressure/Load
Warning
Safety Labels and Locations
Passenger Warning/Discretionary Warning
WARNING
PASSENGER SAFETY
To reduce the risk of SEVERE INJURY or
DEAT H
NEVER CARRY MORE THAN ONE
PASSENGER
NEVER RIDE AFTER USING DRUGS OR
ALCOHOL
NEVER carry a passenger too small to firmly
plant feet on footrests and securely grasp
hand holds.
THE PASSENGER MUST ALWAYS:
• use an approved helmet and protective gear
• securely grasp hand holds and plant feet firmly on footrests while seated in
the passenger seat
• tell operator to slow down or stop if uncomfortable - get off and walk if
conditions require
WARNING
• Never operate this ATV on HILLS steeper than 15 degrees 15°.To
prevent overturn on hilly terrain, use throttle and brakes gradually, and shift
weight uphill.
• REVERSE operation can be dangerous even at low speeds. Steering
becomes difficult. To prevent loss of control, avoid sudden braking or sharp
turns.
7175845
Tire Pressure/Load Warning
WARNING
Improper tire pressure or overloading can cause
loss of control.
Loss of control can result in severe injury or
• DO NOT TOW FROM RACK OR BUMPER. Vehicle damage or tipover may
result causing severe injury or death. Tow only from tow hooks or hitch.
• Maximum Rack Loads: Front 120 lbs. (54 kg) Rear 240 lbs. (109 kg)
Clutch Cover Warning
WARNING
• Moving parts hazard under belt-clutch guard. T o prevent serious injury , do not
operate vehicle with guard removed.
• Do not modify engine or clutch. Doing so can cause part failure, possible
imbalance, and excessive engine RPM, which can result in serious injury or
death.
Hitch Capacity Label
TRAILER MAX WEIGHT:
1500 LBS. (682 KG) ON LEVEL GROUND
850 LBS. (386 KG) UP TO 15° GRADE
HITCH MAX. VERTICAL WEIGHT: 150 LBS. (68 KG)
7175448
7175488
7170509
25
Page 30
FEATURES AND CONTROLS
2x4
Trip 1
km
mi
RPM
FE
88
:
88
Mode/Reverse
Override
Switch
Main Key
Switch
Engine
Stop Switch
Headlight
Switch
4X4
Switch
Switches
Mode/Reverse Override Switch
This vehicle is equipped with a reverse speed limiter system.To gain
additional wheel speed while backing, release the throttle and depress
the override button.
WARNING! Pressing the override button while the throttle is open can cause
loss of control, which may result in serious injury or death. Always release the
throttle before pressing the override button.
The reverse override button also acts as a MODE button when held
down for approximately one half second. See the instrument cluster
information beginning on page 40.
Tip: The override button will not functi on as a MODE button if the transmission
is in reverse.
4X4 Switch
Use the 4X4 switch to engage ADC 4X4, 4X4 or 2X4. See page 39. The
vehicle automatically engages 4X4 when operating in reverse if the
switch is set to either 4X4 position.
26
Page 31
FEATURES AND CONTROLS
OFFOFFRUN
Switches
Engine Stop Switch
Move the stop switch either
left or right to the OFF position
to stop the engine quickly.
Move the stop switch to the
RUN position before attempting to start the engine. The
engine will not start or run
when the switch is off.
Both the main switch and the engine stop switch will shut off all electrical power to the vehicle, including lights.
Main Key Switch
Use the main key switch to start the engine. See page 57.
Headlight Switch
Use the headlight switch to turn the lights on and off and to change the
lights from high beam to low beam. The key must be in the ON position
and the engine stop switch must be in the RUN position.
27
Page 32
FEATURES AND CONTROLS
WARNING
Throttle Lever
Operating an ATV with sticking or improperly operating throttle controls could
cause an accident. Never start or operate an ATV that has a sticking or
improperly operating throttle. Always contact your dealer for service before
operating the vehicle.
Failure to check or maintain proper operation of the throttle system can result in
an accident if the throttle lever sticks during operation. Always check the lever
for free movement and return before starting the engine. Also check
occasionally during operation.
Modifications to the electronic throttle control could result in failure to perform as
designed, which could result in an accident. Do not attempt to modify the throttle
control system or replace it with any after market throttle mechanisms. Always
ensure that the throttle cable is installed and properly routed to the throttle
control.
Engine speed and vehicle movement are controlled by pressing the
throttle lever. The throt tle lever is spring loaded. Engine speed returns to
idle when the lever is released.
This ATV is equipped with
POLARIS Electronic Throttle
Control (ETC), which is
designed to reduce the risk of a
frozen or stuck throttle.
If the throttle cable should stick
in an open position when the
operator releases the throttle
lever, engine speed will be limited, and power to the rear
wheels will be reduced.
28
Page 33
FEATURES AND CONTROLS
WARNING
Brake Lever
Operating the ATV with a spongy brake lever can result in loss of braking, which
could cause an accident. Never operate the ATV with a spongy-feeling brake
lever. Always contact your dealer for service before operating the vehicle.
Squeeze the brake lever toward the
handlebar to apply the front and
rear brakes. These brakes are
hydraulically activated disc type
brakes that are activated by only
one lever.
Always test brake lever travel and
master cylinder fluid level before
riding. When squeezed, the lever
should feel firm. Any sponginess
would indicate a possible fluid leak or low master cylinder fluid level,
which must be corrected before riding. Contact your dealer for proper
diagnosis and repairs.
29
Page 34
FEATURES AND CONTROLS
WARNING
Master Cylinder
Indicator
Window
Master Cylinder/Brake Fluid
An over-full master cylinder may cause brake drag or brake lock-up, which could
result in an accident. Maintain brake fluid at the recommended level. Do not
overfill.
Never store or use a partial bottle of brake fluid. Brake fluid is hygroscopic,
meaning it rapidly absorbs moisture from the air. The moisture causes the
boiling temperature of the brake fluid to drop, which can lead to early brake fade
and the possibility of brake failure, which could result in an accident. After
opening a bottle of brake fluid, always discard any unused portion.
Check the brake fluid in the master
cylinder before each ride.
1. Position the ATV on a level
surface.
2. Position the handlebars so the
master cylinder is level.
3. View the brake fluid level
through the indicator window
on the top of the master cylinder. The eye will appear dark
when the fluid level is full.
When fluid is low , the eye will
be clear.
4. If the fluid level is low, remove the cover screws and add fluid to the
fill line. Do not overfill. Use DOT 4 brake fluid only.
5. Reinstall the cover. Torque screws to 7 in. lbs. (.8 Nm).
30
Page 35
FEATURES AND CONTROLS
Parking Brake
Locking the Parking Brake
1. Place the transmission in
PARK.
2. Squeeze and release the brake
lever two or three times, then
squeeze and hold.
3. Push the parking brake lock
forward to engage the lock.
4. Release the brake lever.
5. To release the parking brake lock, squeeze and release the brake
lever. It will return to its unlocked position.
WARNING! Operating the ATV while the parking brake is engaged could result
in an accident or fire. Always check to be sure the parking brake is disengaged
before operating.
The parking brake may relax if left on for a long period of time. Always
block the wheels to prevent rolling. Always block the wheels on the
downhill side of the ATV if leaving it parked on a hill. Another option is
to park the ATV in a sidehill position. Never depend on the parking
brake alone if the ATV is parked on a hill. Always block the wheels to
prevent rolling.
31
Page 36
FEATURES AND CONTROLS
WARNING
Auxiliary
Foot Brake
Brake Fluid
Reservoir
Auxiliary Foot Brake
Never back down a hill. Applying the auxiliary brake when backing down a hill
may cause rear tipover, which could result in serious injury or death.
Use caution when applying the auxiliary brake. Do not aggressively apply the
auxiliary brake when going forward. The rear wheels may skid and slide
sideways, causing loss of control and serious injury or death.
The auxiliary brake system is
intended to be used as a backup for
the main brake system. Should the
main system fail, use the auxiliary
foot brake.
The auxiliary foot brake is located
on the inside of the right footrest.
Operate this brake with your right
foot.
If the rear wheels slide while using
the auxiliary brake, reduce brake
pedal pressure to brake the rear
wheels without skidding.
Brake Fluid Level
Check the brake fluid level frequently for the auxiliary brake system. The reservoir is located under
the front storage box. See page 36.
Maintain the fluid level between
the maximum and minimum marks.
Use DOT 4 brake fluid only.
NOTICE: Do not use ADC fluid in the
brake fluid reservoir. ADC
fluid will damage the rubber
components of the brake
system.
32
Page 37
FEATURES AND CONTROLS
Gear
Selector
Automatic Transmission Gear Selector
The transmission gear
selector is located on the
right side of the vehicle.
H: High Gear
L: Low Gear
N: Neutral
R: Reverse
P: Park
To shift gears, brake to a
complete stop. When the
engine is idling, move
the lever to the desired
gear.
NOTICE: Shifting gears with the engine speed above idle or while the vehicle is
Whenever the ATV is left unattended, always place the transmission in
PARK and lock the parking brake.
Belt Life
To extend belt life, use low forward gear when pulling a heavy load at
less than seven miles per hour for extended periods and when operating
uphill at a slow speed.
moving could cause transmission damage.
33
Page 38
FEATURES AND CONTROLS
Tight Position
Less Tight Position
Electronic Power Steering (EPS)
Electronic power steering engages when the ignition key is turned to the
ON position. EPS remains engaged whether the vehicle is moving or
idle. See page 41 for EPS Warning Indicator information.
Passenger Seat
Always make sure the passenger seat is installed and securely latched
before operating with a passenger. Test the seat latch by attempting to
pull the seat upward. If the lock-out is not working properly, do not allow a passenger to ride the vehicle. See your POLARIS dealer for service.
See pages 95-96 for passenger seat adjustment procedures.
See page 95 for passenger seat removal and installation procedures.
Beverage Holders
This vehicle is equipped with
beverage holders on each side
of the passenger seat. To
secure a beverage or other
container, remove the rubber
retainer strap from one side of
the holder. Place the container
into the recess and reinstall the
strap over the top of the container. Place one of the rubber
cylinders through one of the
holes to secure a strap.
When trailering the vehicle,
and whenever a holder is not
in use, always secure the rubber straps in one of the tighter
positions to prevent loss of the
retainer.
34
Page 39
FEATURES AND CONTROLS
Fuel Tank
Cap
Fuel Tank
Always refuel with the engine
stopped, and outdoors or in a well
ventilated area. Refuel on a level
surface.
Remove the fuel tank cap and add
fuel. Use either leaded or unleaded
gasoline with a minimum pump
octane number of 87=(R+ M/2)
octane. Do not use fuel with ethanol
content greater than 10%, such as
E-85 fuel.
The fuel tank is designed to allow
for the normal expansion of fuel. Do
not overfill. Do not fill the tank
neck.
35
Page 40
FEATURES AND CONTROLS
Cover LatchesPlunger Latches
ADC Fluid
Reservoir
Brake Fluid
Reservoir
Radiator
Cap
Coolant
Bottle Cap
Electrical/Fuse/Relay
Battery
Front Storage Box
Open the front storage box to access the under-compartment area.
1. Release the front
box cover latches
and lift the cover.
2. Release the plunger
latches that secure
the box to the
frame.
3. Close the cover and
lift the unlatched
edge of the box to
disengage the plungers. Pivot the box forward.
4. T o remove the box completel y, disengage the plungers and slide the
box rearward and upward.
5. Always secure the plunger latches and the cover latches before
operating the vehicle.
Access the following components under the front box:
The All Wheel Drive system is
controlled by the 4X4 switch.
ADC 4X4 Mode
When the switch is on ADC 4X4,
the ADC system allows engine
braking to all four wheels when
the vehicle descends a hill or
incline. Always move the 4X4
switch to ADC 4X4 before
ascending or descending a hill.
See page 39.
4X4 Mode
When the switch is on 4X4, the
ATV is in 4X4, and the 4X4 indicator icon in the instrument cluster display will be visible.
When in 4X4, the demand drive
unit will automatically engage
any time the rear wheels lose
traction. When the rear wheels
regain traction, the demand drive
unit will automatically disengage.
There is no limit to the length of time the vehicle may remain in 4X4.
The vehicle automatically engages 4X4 when operating in reverse if the
switch is set to either 4X4 position.
2X4 Mode
When the switch is on 2X4, the ATV is in two-wheel drive at all times.
37
Page 42
FEATURES AND CONTROLS
All Wheel Drive System
Engaging 4X4
The 4X4 switch may be turned on or off while the vehicle is moving.
Initially, the vehicle's electronic system will not enable 4X4 until the
engine RPM is below 3100. Once enabled, 4X4 remains enabled until
the 4X4 switch is turned off. If the switch is turned of f while the demand
drive unit is moving, it will not disengage until the rear wheels regain
traction.
Engage the 4X4 switch before getting into conditions where front wheel
drive may be needed. If the rear wheels are spinning, release the throttle
before switching to 4X4.
NOTICE: Switching to 4X4 or ADC 4X4 while the rear wheels are spinning may
cause severe drive shaft and gearcase damage. Always switch to
4X4 or ADC 4X4 while the rear wheels have traction or are at rest.
38
Page 43
FEATURES AND CONTROLS
Active Descent Control (ADC) System
The ADC system allows engine braking to all four wheels when the
vehicle descends a hill or incline. Always move the 4X4 switch to ADC
4X4 before ascending or descending a hill.
Engaging Active Descent Control
The ADC system will automatically engage when all four of the following conditions occur:
• The 4X4 switch must be in the ADC 4X4 position
• Vehicle speed must be 15 mph (24 km/h) or less
• The throttle must be closed (throttle lever released)
• The transmission must be in gear (high, low or reverse)
Disengaging Active Descent Control
The ADC system will automatically disengage if at least one of the following conditions occur:
• The 4X4 switch is moved out of the ADC 4X4 position
• Vehicle speed exceeds 15 mph (24 km/h)
• The throttle is open (throttle is applied)
• The transmission is shifted to neutral or park
39
Page 44
FEATURES AND CONTROLS
Trip 1
km
mi
RPM
FE
88:88
Rider
Information
Center
Speedometer
Indicator Lamps
Instrument Cluster
NOTICE: High water pressure may damage ATV components. Wash the ATV
Digital/Analog Gauge
Speedometer
The speedometer displays vehicle speed in either miles per hour (MPH)
or kilometers per hour (km/h).
by hand or with a garden hose using mild soap.
Certain products, including insect repellents and chemicals, will
damage the speedometer lens and other plastic surfaces. Do not use
alcohol to clean the instrument cluster. Do not allow insect sprays to
contact the lens. Immediately clean off any gasoline that splashes on
the instrument cluster.
40
Page 45
FEATURES AND CONTROLS
Instrument Cluster
Digital/Analog Gauge
Indicator Lamps
LampIndicatesCondition
Vehicle
Speed
Over
Temperature
EPS Warning This indicator illuminates when the key is turned to
NeutralThis lamp illuminates when the transmission is in
High BeamThis lamp illuminates when the headlamp switch is
Check Engine This indicator appears if an EFI-related fault occurs.
When standard mode is selected, speed displays in
miles per hour.
When metric mode is selected, speed displays in
kilometers per hour.
This lamp flashes to indicate an overheated engine. If
the indicator stops flashing but remains illuminated,
the overheating condition remains, and the system
will automatically reduce engine power.
the ON position and goes off when the engine is
started. If the light remains on after starting the
engine, the EPS system is inoperative. See your
authorized POLARIS dealer for service.
neutral and the ignition key is in the ON position.
set to high beam.
Do not operate the ATV if this warning appears.
Serious engine damage could result. See your dealer.
41
Page 46
FEATURES AND CONTROLS
1
2
6
5
7
3
4
Instrument Cluster
Digital/Analog Gauge
Rider Information Center
The rider information center is located in the instrument cluster . All segments will light up for one second at start-up. If the instrument cluster
fails to illuminate, a battery over-voltage may have occurred and the
instrument cluster may have shut off to protect the electronic speedometer. If this occurs, take the ATV to your POLARIS dealer for proper
diagnosis.
The information center is set to display standard units of measurement
and a 12-hour clock at the factory. To change to metric and/or a 24 -hour
clock, see page 45.
EF
Trip 1
88
km
:
88
RPM
mi
42
Page 47
FEATURES AND CONTROLS
Instrument Cluster
Digital/Analog Gauge
Rider Information Center
1. Gear Display - This area displays gear shifter position.
H = High Gear
L = Low Gear
N = Neutral
R = Reverse Gear
P = Park
-- = Gear Signal Error (or shifter between gears)
2. Fuel Gauge Display - The segments of the fuel gauge show the
level of fuel in the fuel tank. When the last segment clears, a low
fuel warning is activated. All segments including the fuel icon will
flash. Refuel immediately.
Tip: If the fuel icon fails to display, an open or short circuit has occurred in the
fuel sensor circuit. See your dealer.
3. Information Display - This area displays odometer, trip meter,
engine hour meter, engine speed and programmable service hour
interval.
4. Active Descent Control Display - This icon displays when ADC is
active. See page 39.
5. Clock Display - The clock displays time in a 12-hour or 24-hour
format. If the engine is turned off, press the MODE button. The
time will display for 5-10 seconds. See page 45 for resetting instructions.
6. Service Reminder Display - A flashing wrench symbol alerts the
operator that the preset service interval has been reached. The vehicle should be brought to your dealer for scheduled maintenance. See
page 45 for resetting instructions.
7. 4X4 Display - This icon displays when the 4X4 system is engaged
(switch is on either ADC 4X4 or 4X4).
43
Page 48
FEATURES AND CONTROLS
Instrument Cluster
Digital/Analog Gauge
Rider Information Center
The reverse override button acts as the MODE button when pressed and
released quickly. The transmission cannot be in reverse when using the
override button as a MODE button. This feature does not contain a vehicle speed lockout function and can be used at any operating speed.
Display Units (Standard/Metric)
The display can be changed to display either standard or metric units of
measurement.
Tip: To exit the set-up mode at any time, wait 10 seconds.The display automati-
3. Press and hold the MODE button while turning the key to the ON
position.
4. When the display flashes the distance setting, tap the MODE button
to advance to the desired setting.
5. Press and hold the MODE button to save the setting and advance to
the next display option.
6. Repeat the procedure to change remaining display settings.
44
Page 49
FEATURES AND CONTROLS
Instrument Cluster
Digital/Analog Gauge
Rider Information Center
Clock Mode
Tip: The clock must be reset any time the battery has been disconnected or dis-
charged.
1. Turn the key to the ON position. Use the MODE button to toggle to
the odometer display.
2. Press and hold the MODE button until the hour segment flashes.
Release the button.
3. With the segment flashing, tap the MODE button to advance to the
desired setting.
4. Press and hold the MODE button until the next segment flashes.
Release the button.
5. Repeat steps 3-4 twice to set the 10-minute and 1-minute segments.
After completing the 1-minute segment, step 4 will save the new
settings and exit the clock mode.
6. Turn the key to the OFF position.
Odometer Mode
The odometer records and displays the distance traveled by the ATV.
Trip Meter Mode
The trip meter records the distance traveled by the ATV if reset before
each trip. T o reset, select the trip meter mode. Press and hold the MODE
button until the meter resets to zero. In the Rider Information Center, the
trip meter display contains a decimal point, but the odometer displays
without a decimal point.
Hour Meter Mode
This mode logs the total hours the engine has been in operation.
45
Page 50
FEATURES AND CONTROLS
Instrument Cluster
Digital/Analog Gauge
Rider Information Center
Programmable Service Interval
When the hours of engine operation equal the programmed service
interval setting, the wrench icon will flash for 5 seconds each time the
engine is started. When this feature is enabled, it provides a convenient
reminder to perform routine maintenance. The service interval is programmed at 50 hours at the factory. Use the following procedure to
change the service interval.
1. Press the MODE button until remaining service hours display.
2. Press and hold the MODE button.
3. When the service hours flash, press and release the MODE button to
advance the hours to the desired setting (including OFF). Press and
hold the MODE button to set the new service hour interval.
Diagnostic Display Mode
The EFI diagnostic display mode is for informational purposes only.
Please see your POLARIS dealer for all major repairs.
The diagnostic mode is accessible only when the check engine warning
indicator activates after the key has been turned on. Leave the key on if
you want to view the active code (failure code).
The diagnostic mode becomes inaccessible if the key is turned off and
on and the warning indicator is no longer active. This allows the determination of persistent as well as intermittent faults.
Inactive codes are stored in the history of the unit.
46
Page 51
Instrument Cluster
Suspect Parameter
Number (SPN)
Error Code
Number (0-9)
Failure Mode Indicator (FMI)
Digital/Analog Gauge
Rider Information Center
Engine Error Codes
The error screen displays
only when the CHECK
ENGINE light is on or when
it goes on and off during one
ignition cycle. Error codes
are not stored in the gauge
when the key is turned off.
The code and message is
lost, but will reappear if the
fault reoccurs after restarting the engine.
If the CHECK ENGINE
light illuminates, retrieve
the error codes from the display . Please see your Polaris
dealer for all major repairs.
1. If the error codes are not displayed, use the MODE button to toggle
2. Press and hold the MODE button to enter the diagnostics code
3. Record the numbers displayed in the gear position (if any), clock
4. Press the MODE button to advance to the next error code.
5. Press and hold the MODE button to exit the diagnostics code menu.
6. See pages 48-51 for code definitions and failure descriptions. Please
FEATURES AND CONTROLS
until “Ck ENG” displays on the main line of the display.
menu.
and odometer displays.
see your Polaris dealer for all major repairs.
47
Page 52
FEATURES AND CONTROLS
Instrument Cluster
Diagnostic Display Code Definitions
Open Load: There is a break in the wires that lead to the item listed in
the chart (injector, fuel pump, etc.), or the item has failed.
Short-to-Ground:
control unit and the item listed in the chart.
Shorted Load:
shorted together, or the item has shorted internally.
Short-to-Battery:
the electronic control unit is shorted to a wire at battery voltage.
ComponentConditionSPNFMI
Throttle Position Sensor
Engine Temperature Sensor
Intake Air Temperature Sensor
Manifold Absolute Pressure Sensor Voltage Too High1023
Crankshaft Position SensorCircuit Fault6368
Gear Sensor SignalVoltage Too Low (to Calibrate)5234
Fan Relay Driver CircuitDriver Circuit Open/Grounded10715
The wire is shorted to ground between the electronic
The wires leading to the item listed in the chart are
The wire leading from the item listed in the chart to
SPORTSMAN 550 Touring Diagnostic Codes
Voltage Too High513
Voltage Too Low514
Voltage Too High1103
Voltage Too Low1104
Temperature Too High11016
Engine Overheat Shutdown1100
Voltage Too High1053
Voltage Too Low1054
Voltage Too Low1024
Voltage Too High5233
Signal Fault5232
Driver Circuit Short to B+6513
Driver Circuit Short to B+12683
Driver Circuit Open/Grounded13475
Driver Circuit Short to B+13473
Driver Circuit Short to B+10713
48
Page 53
FEATURES AND CONTROLS
Instrument Cluster
Diagnostic Display Code Definitions
SPORTSMAN 550 Touring Diagnostic Codes
ComponentConditionSPNFMI
Idle Air ControlDriver Circuit Grounded5201935
Shorted Load*52019311
Starter Enable CircuitDriver Circuit Short to B+13213
All Wheel Drive ControlDriver Circuit Short to B+5202073
System PowerVoltage Too High1683
Voltage Too low1684
Throttle Safety SignalVoltage Too High5201943
Voltage Too Low5201944
Signal Out of Range5201942
Throttle Stuck5201947
Active Descent Control SystemDriver Circuit Short to B+5202033
EPS Models Only
Steering Over Current Shut DownCurrent Above Normal or
Steering Excessive Current ErrorCurrent Above Normal or
Steering Torque Sensor T1 Partial
Failure
Steering Torque Sensor T2 Partial
Failure
Steering Torque Sensor Full FailureT1 and T2 Shorted to Ground5202254
Steering Position Sensor P1 Partial
Failure
Steering Position Sensor P2 Partial
Failure
Steering Position Sensor Full Failure P1 and P2 Shorted to Ground5202284
EPAS Inverter TemperatureGreater than 110 Degrees C52022916
EPAS CAN Communications
Receive Error
EPAS CAN Communications
Transmit Error
Grounded
Grounded
T1 Shorted to Ground5202234
T1 Shorted to Bus5202233
T2 Shorted to Ground5202244
T2 Shorted to Bus5202243
T1 and T2 Shorted to Bus5202253
T1 Shorted to Ground & T2
Shorted to Bus
T2 Shorted to Ground & T1
Shorted to Bus
T1 and T2 are Shorted5202252
P1 Shorted to Ground5202264
P1 Shorted to Bus5202263
P2 Shorted to Ground5202274
P2 Shorted to Bus5202273
P1 and P2 Shorted to bus5202283
Greater than 120 Degrees C5202290
No RX Message for 2 Seconds5202309
No TX Message for 2 Seconds5202319
*Assumes unipolar configuration of stepper motor
5202216
5202226
52022516
52022517
49
Page 54
FEATURES AND CONTROLS
Instrument Cluster
Diagnostic Display Code Definitions
SPORTSMAN 850 Touring Diagnostic Codes
ComponentConditionSPNFMI
Throttle Position SensorVoltage Too High513
Voltage Too Low514
Engine Temperature SensorVoltage Too High1103
Voltage Too Low1104
Temperature Too High11016
Engine Overheat Shutdown1100
Intake Air Temperature SensorVoltage Too High1053
Voltage Too Low1054
Manifold Absolute Pressure SensorVoltage Too High1023
Voltage Too Low1024
Signal Out of Range1022
Crankshaft Position SensorCircuit Fault6368
Plausibility Fault6362
Vehicle Speed SignalSpeed Too High848
Plausibility Fault842
Gear Sensor SignalVoltage Too Low 5234
Voltage too high5233
Signal fault5232
Injector 1 (MAG) (SDI Part Load)Driver Circuit Open/Grounded6515
Driver Circuit Short to B+6513
Driver Circuit Grounded6514
Injector 2 (PTO) (SDI Part Load)Driver Circuit Open/Grounded6525
Driver Circuit Short to B+6523
Driver Circuit Grounded6524
Ignition Coil Primary Driver 1 (MAG) Driver Circuit Short to B+12683
Ignition Coil Primary Driver 2 (PTO)Driver Circuit Short to B+12693
Fuel Pump Driver CircuitDriver Circuit Open/Grounded13475
Driver Circuit Short to B+13473
Driver Circuit Grounded13474
Fan Relay Driver CircuitDriver Circuit Open/Grounded10715
Driver Circuit Short to B+10713
Driver Circuit Grounded10714
Idle Air ControlDriver Circuit Open/Grounded6345
Driver Circuit Short to B+6343
Driver Circuit Grounded6344
Position Out of Range6347
Starter Enable CircuitDriver Circuit Open/Grounded13215
Driver Circuit Short to B+13213
Driver Circuit Grounded13214
50
Page 55
FEATURES AND CONTROLS
Instrument Cluster
Diagnostic Display Code Definitions
SPORTSMAN 850 Touring Diagnostic Codes
ComponentConditionSPNFMI
Chassis RelayDriver Circuit Open/Grounded5202085
Driver Circuit Short to B+5202083
Driver Circuit Grounded5202084
All Wheel Drive ControlDriver Circuit Open/Grounded5202075
Driver Circuit Short to B+5202073
Driver Circuit Grounded5202074
System PowerVoltage Too High1683
Voltage Too low1684
Throttle Safety SignalVoltage Too High5201943
Voltage Too Low5201944
Signal Out of Range5201942
Throttle Stuck5201947
Active Descent Control SystemDriver Circuit Open/Grounded5202035
Driver Circuit Short to B+5202033
Driver Circuit Grounded5202034
Idle SpeedSpeed Too High5202113
Speed Too Low5202114
EPS Models Only
Steering Over Current Shutdown Current Above Normal/Grounded5202216
Steering Excessive Current Error Current Above Normal/Grounded5202226
Steering Torque Sensor T1 Par-
tial Failure
Steering Torque Sensor T2 Par-
tial Failure
Steering Torque Sensor Full
Failure
Steering Position Sensor P1
Partial Failure
Steering Position Sensor P2
Partial Failure
Steering Position Sensor Full
Failure
EPAS Inverter TemperatureGreater than 110 Degrees C52022916
EPAS CAN Comm. Receive Err No RX Message for 2 Seconds5202309
EPAS CAN Comm. Transmit Err No TX Message for 2 Seconds5202319
IC CAN Comm. w/EPASEPAS Offline52023031
T1 Shorted to Ground5202234
T1 Shorted to Bus5202233
T2 Shorted to Ground5202244
T2 Shorted to Bus5202243
T1 and T2 Shorted to Ground5202254
T1 and T2 Shorted to Bus5202253
T1 Short to Ground & T2 Short to Bus 520225 16
T2 Short to Ground & T1 Short to Bus 520225 17
T1 and T2 are Shorted5202252
P1 Shorted to Ground5202264
P1 Shorted to Bus5202263
P2 Shorted to Ground5202274
P2 Shorted to Bus5202273
P1 and P2 Shorted to Ground5202284
P1 and P2 Shorted to bus5202283
Greater than 120 Degrees C5202290
51
Page 56
OPERATION
WARNING
Failure to operate the ATV properly can result in a collision, loss of control,
accident or overturn, which may result in serious injury or death. Read and
understand all safety warnings outlined in the safety section of this owner’s
manual.
Break-In Period
The break-in period for your new POLARIS ATV is the first ten hours
of operation, or the time it takes to use the first two full tanks of gasoline. No single action on your part is as important as following the procedures for a proper break-in. Careful treatment of a new engine and
drive components will result in more efficient performance and longer
life for these components.
NOTICE: Excessive heat build-up during the first three hours of operation will
damage close-fitted engine parts and drive components. Do not
operate at full throttle or high speeds during the first three hours of
use.
52
Page 57
OPERATION
Break-In Period
Engine and Drivetrain Break-in
1. Fill the fuel tank with gasoline. See page 35. Always exercise
extreme caution whenever handling gasoline.
2. Check the engine oil level on the dipstick. See page 81. Add oil if
necessary to maintain the level between the safe and add marks.
3. Drive slowly at first. Select an open area that allows room to famil-
iarize yourself with vehicle operation and handling.
4. Vary the throttle positions. Do not operate at sustained idle.
5. Perform regular checks on fluid levels, controls and areas outlined
on the daily pre-ride inspection checklist. See page 54.
6. Pull only light loads.
7. Change both the oil and the filter at 20 hours, one month or 500
miles (800 km), whichever comes first.
PVT Break-in (Clutches/Belt)
A proper break-in of the clutches and drive belt will ensure a longer life
and better performance. Break in the clutches and belt by operating at
slower speeds during the break-in period as recommended. Pull only
light loads. Avoid aggressive acceleration and high speed operation during the break-in period.
53
Page 58
OPERATION
Pre-Ride Checklist
Failure to inspect and verify that the ATV is in safe operating condition
before operating increases the risk of an accident. Always inspect the
ATV before each use to make sure it's in safe operating condition.
Engine stop switchEnsure proper operation27
Air filter, pre-filterInspect, clean101
HeadlampCheck opera tion27
Brake light/taillightCheck operation107
Riding gearWear approved helmet, goggles, and
ADC FluidEnsure proper level87
protective clothing
93
81
92
120
103
8
54
Page 59
OPERATION
Safe Operation Practices
1. Complete the recommended safety training before operating this
vehicle. See page 7.
2. Do not allow anyone under 16 years of age to operate this vehicle.
Do not allow anyone with cognitive or physical disabilities to operate this vehicle.
3. Engine exhaust fumes are poisonous. Never start the engine or let it
run in an enclosed area.
4. Before operating, learn how to use the auxiliary brake for emer-
gency situations (if service brakes become inoperable).
5. Operate this vehicle off-road only. Never operate the vehicle on
pavement or on any public street, road or highway, including dirt
and gravel roads.
6. Use caution and drive at reduced speeds in conditions of reduced
visibility such as fog, rain and darkness. Clean headlights frequently and replace burned out headlamps promptly.
7. Drive in a manner appropriate for your skills, your passenger’s
skills and operating conditions. Never operate at excessive speeds.
Never attempt wheelies, jumps, or other stunts. Never remove your
hands from the handlebars while operating, and always keep both
feet on the footrests.
8. Never consume alcohol or drugs before or while operating an ATV.
9. Always use the size and type of tires specified for your vehicle.
Always maintain proper tire pressure.
10. Never operate a damaged ATV. After any overturn or accident, have
a qualified service dealer inspect the entire machine for possible
damage.
11. Never operate the ATV on a frozen body of water unless you have
independently verified that the ice is sufficiently thick to support the
weight and moving force of the ATV, you and your cargo, together
with any other vehicles in your party.
12. Do not touch hot exhaust system components. Always keep com-
bustible materials away from the exhaust system.
13. Always remove the ignition key when the vehicle is not in use to
prevent unauthorized use.
55
Page 60
OPERATION
Know Your Riding Area/Tread Lightly
Familiarize yourself with all laws and regulations concerning the operation of this off-road vehicle in your area. Respect the environment in
which you ride. Find out where the designated riding areas are by contacting your POLARIS dealer, a local riding club or local officials.
Help keep our trails open for recreational vehicle use. As an off-road
enthusiast, you represent the sport and can set a good example (or a poor
example) for others to follow . T read lightly. Operate with respect for the
terrain, avoid littering, and always stay on the designated trails.
Trail Etiquette
Always practice good etiquette when riding. Allow a safe distance
between your vehicle and other vehicles operating in the same area.
Communicate to oncoming operators by signaling the number of vehicles in your group. When stopping, move your vehicle to the edge of the
trail as far as possible to allow others to pass safely.
56
Page 61
OPERATION
Starting the Engine
1. Position the vehicle on a level surface outdoors or in a well-ventilated area.
2. Place the transmission in PARK.
3. Lock the parking brake.
Tip: The starter interlock will prevent the engine from starting if the transmission
is in gear and the brake is not engaged.
4. Sit on the vehicle and move the engine stop switch to RUN.
Tip: Do not press the throttle while starting the engine.
5. Turn the ignition key past the ON position to engage the starter.
Activate the starter for a maximum of five seconds, releasing the
key when the engine starts.
6. If the engine does not start, return the key to the OFF position and
wait five seconds before attempting to start again. Activate the
starter for another five seconds if necessary. Repeat this procedure
until the engine starts.
NOTICE: Operating the vehicle immediately after starting could cause engine
Cold Weather Operation
If the ATV is used year-round, check the oil level frequently. A risi ng oil
level could indicate the accumulation of contaminates such as water or
excess fuel in the bottom of the crankcase. Water in the bottom of the
crankcase can lead to engine damage and must be drained. Water accumulation increases as outside temperature decreases.
damage. Allow the engine to warm up for several minutes before
operating the vehicle.
57
Page 62
OPERATION
Driving Procedures
1. Wear protective riding gear. See page 8.
2. Perform the pre-ride inspection. See page 54.
3. Place the transmission in PARK.
4. Lock the parking brake.
5. Mount the vehicle from the left side.
6. Sit upright with both feet on the footrests and both hands on the
handlebars.
7. Start the engine and allow it to warm up.
8. Shift the transmission into gear.
9. Check your surroundings and determine your path of travel.
10. Release the parking brake.
11. Slowly depress the throttle with your right thumb and begin driving.
12. Drive slowly. Practice maneuvering and using the throttle and
brakes on level surfaces.
58
Page 63
OPERATION
Turning the Vehicle
Both rear wheels drive
equally at all times. This
means that the outside wheel
must travel a greater distance
than the inside wheel when
turning, and the inside tire
must slip traction slightly.
1. Slow down.
2. Never turn quickly when
carrying a passenger or
cargo.
3. Steer in the direction of
the turn.
4. Keep both feet on the
footrests.
5. Lean your upper body to the inside of the turn while supporting your
weight on the outer footrest. This technique alters the balance of
traction between the rear wheels, allowing the turn to be made
smoothly. The same leaning technique should be used for turning in
reverse.
6. Practice making turns at slow speeds before attempting to turn at
faster speeds.
WARNING! Turning improperly can result in vehicle overturn. Never turn
abruptly or at sharp angles. Never turn at high speeds.
59
Page 64
OPERATION
Driving with a Passenger
1. Never allow anyone under 12 years of age to ride as a passenger on
this 2-up ATV. Make sure any passenger is tall enough to comfortably and safely reach the grab handles and footrests.
2. Do not carry a passenger until you have at least two hours of driving
experience with this vehicle.
3. Make sure the passenger is wearing appropriate riding gear, includ-
ing an approved helmet with a rigid chin guard. See page 8.
4. Perform the pre-ride
inspection. See page 54.
5. Always make sure the
passenger seat is installed
and securely latched
before operating with a
passenger.
6. Lock the parking brake.
7. Mount the vehicle from
the left side. After the
operator is seated, the
passenger should mount
the vehicle from the left
side. Always make sure
the brake is engaged to
ensure the vehicle
remains motionless whenever a passenger mounts or dismounts.
8. Allow a passenger to ride only in the approved passenger seat.
9. Do not carry more than one passenger.
10. Slow down. Control may be more difficult with a passenger on
board. Allow more time and distance for braking.
60
Page 65
OPERATION
Driving with a Passenger
11. Ride to the ability of your passenger, instead of to your own ability.
Av oid unexpected or aggressive maneuvers that could cause a passenger to fall from the vehicle.
12. Do not cross a hillside with a passenger on board. See page 64.
13. A passenger should always be seated in the passenger seat with both
feet on the footrests and both hands on the passenger grab handles
at all times. The passenger should never hold on to the operator.
Never secure a passenger to the vehicle or to the operator with a
belt, rope or similar device.
14. Make sure the passenger understands the importance of "active
riding." When hill-climbing or performing maneuvers, a passenger
should shift body weight in the same manner in which the driver
shifts body weight. For example, the passenger should lean to the
inside of a turn along with the operator and should always lean
uphill when climbing and descending hills.
61
Page 66
OPERATION
Sideways
skid
Tur n in
direction of
skid
Driving on Slippery Surfaces
Whenever riding on slippery surfaces such as wet trails or loose gravel,
or during freezing weather, follow these precautions:
1. Do not operate on excessively rough, slippery or loose terrain.
2. Slow down when entering slippery areas.
3. Engage 4X4 before wheels begin to lose traction.
NOTICE: Severe damage to drive train may occur if the 4X4 is engaged while
4. Maintain a high level of alertness, reading the trail and avoiding
5. Never apply the brakes during a skid. Correct a skid by turning the
the wheels are spinning. Allow the rear wheels to stop spinning
before engaging 4X4, or engage 4X4 before wheels begin to lose
traction.
quick, sharp turns, which can cause skids.
handlebars in the direction of the skid and shifting your body
weight forward.
62
Page 67
OPERATION
15° Maximum
Driving Uphill
Braking and handling are greatly affected when operating in hilly terrain. Improper procedure could cause loss of control or overturn. Whenever traveling uphill, follow these precautions:
1. Always move the 4X4 switch to ADC 4X4 before ascending or
descending a hill. See page 39.
2. Drive straight uphill.
3. Avoid steep hills (15° maximum).
4. Always check the terrain carefully before ascending any hill.
5. Never climb hills with excessively slippery or loose surfaces.
6. Keep both feet on the footrests.
7. Shift body weight uphill. A passenger should also shift body weight
uphill.
8. Proceed at a steady rate of speed and throttle opening. Opening the
throttle suddenly could cause the ATV to flip over backwards.
9. Never go over the top of any hill at high speed. An obstacle, a sharp
drop, or another vehicle or person could be on the other side of the
hill.
10. Remain alert and be prepared to take emergency action. This may
include quick dismounting of the vehicle.
63
Page 68
OPERATION
Driving on a Sidehill (Sidehilling)
Driving on a sidehill is not recommended. Improper procedure could
cause loss of control or overturn. Avoid crossing the side of any hill
unless absolutely necessary.
If crossing a sidehill is unavoidable, follow these precautions:
1. Slow down.
2. Avoid crossing the side of a steep hill.
3. Do not cross a hillside with a passenger on board. Ask the passenger
to dismount and walk across the hillside before remounting the
vehicle.
4. Lean into the hill, transferring your upper body weight toward the
hill while keeping your feet on the footrests.
5. If the vehicle begins to tip, quickly turn the front wheel downhill, if
possible, or dismount on the uphill side immediately!
64
Page 69
OPERATION
15° Maximum
Driving Downhill
When driving downhill, follow these precautions:
1. Always check the terrain carefully before descending a hill.
2. Always move the 4X4 switch to ADC 4X4 before ascending or
descending a hill. See page 39.
3. Always descend a hill with the transmission in forward gear. Do not
descend a hill with the transmission in neutral.
4. Slow down. Never travel down a hill at high speed.
5. Drive straight downhill. Avoid traveling down a hill at an angle,
which would cause the vehicle to lean sharply to one side.
6. Shift body weight uphill. A passenger should also shift body weight
uphill.
7. Apply the brakes slightly to aid in slowing. Applying the brakes too
firmly may cause the rear wheels to lock, which could result in loss
of control.
65
Page 70
OPERATION
8 ft. (2.4 m)
Turning Around on a Hill (K-Turn)
If the vehicle stalls while climbing a hill, never back it down the hill!
Use the K-turn to turn around.
66
Page 71
OPERATION
Turning Around on a Hill (K-Turn)
1. Stop and lock the parking brake while keeping body weight uphill.
2. Always move the 4X4 switch to ADC 4X4 before ascending or
descending a hill. See page 39.
3. Leave the transmission in forward and shut off the engine.
4. If a passenger is on board, ask the passenger to dismount first, then
the operator may dismount. Dismount on the uphill side of the vehicle, or on the left if the vehicle is pointing straight uphill. A passen-
ger should not remount until the vehicle returns to firm, level
ground.
5. Staying uphill of the vehicle, turn the handlebars full left.
6. While holding the brake lever, release the parking brake lock and
slowly allow the vehicle to roll around to your right until it's pointing across the hill or slightly downward.
7. Lock the parking brake. Remount the vehicle from the uphill side,
keeping body weight uphill. A passenger should not remount until
the vehicle returns to firm, level ground.
8. Start the engine with the transmission still in forward.
9. Release the parking brake and proceed slowly , controlling speed
with the brake lever, until the vehicle is on more level ground.
67
Page 72
OPERATION
Maximum Depth
Driving Through Water
Your ATV can operate
through water with a
maximum recommended
depth equal to the bottom
of the footrests. Follow
these procedures when
operating through water:
1. Determine water
depths and current
before entering water.
2. Choose a crossing
where both banks have
gradual inclines.
3. Avoid operating
through deep or fast-flowing water.
NOTICE: Major engine damage can result if the vehicle is not thoroughly
4. After leaving water, test the brakes. Apply them lightly several
If it’s unavoidable to enter water deeper than the footrest level:
• Proceed slowly. Avoid rocks and obstacles.
• Balance your weight carefully. Avoid sudden movements.
• Maintain a steady rate of speed. Do not make sudden turns or stops.
Do not make sudden throttle changes.
inspected after operation in water. Perform the services outlined in
the maintenance chart. See page 76. The following areas need
special attention: engine oil, transmission oil, demand drive fluid and
all grease fittings
If the vehicle tips or overturns in water, or if the engine stops during or
after operating in water, restarting can result in serious engine
damage. Transport the vehicle to your dealer for service before
restarting the engine. If this is not possible, follow the vehicle
immersion inspection and drying procedures outlined on page 1 10,
then see your dealer for service at the first opportunity.
.
times while driving slowly. The friction will help dry out the pads.
68
Page 73
OPERATION
Driving Over Obstacles
Follow these precautions when operating over obstacles:
1. Always check for obstacles before operating in a new area.
2. Look ahead and learn to read the terrain. Be constantly alert for hazards such as logs, rocks and low hanging branches.
3. Travel slowly and use extra caution when operating on unfamiliar
terrain. Not all obstacles are immediately visible.
4. Never attempt to operate over large obstacles, such as rocks or
fallen trees.
5. Always have a passenger dismount before operating over an obstacle that could cause a fall from the vehicle or vehicle tipover.
69
Page 74
OPERATION
Driving in Reverse
Follow these precautions when operating in reverse:
1. Always check for obstacles or people behind the vehicle. Be aware
that a passenger can obstruct your view.
2. Always avoid backing downhill.
3. Back slowly.
4. Apply the brakes lightly for stopping.
5. Avoid turning at sharp angles.
6. Never open the throttle suddenly.
7. Do not use the override switch unless additional wheel speed is
required for vehicle movement. Use the override with caution as
rearward vehicle speed is greatly increased. Do not operate at wide
open throttle. Operate the throttle just enough to maintain a desired
speed.
NOTICE: Excessive throttle operation while in the speed limit mode may cause
fuel to build in the exhaust, resulting in engine popping and/or engine
damage.
70
Page 75
OPERATION
Parking on an Incline
Avoid parking on an incline if possible. If it's unavoidable, follow these
precautions:
1. Stop the engine.
2. Place the transmission in PARK.
3. Lock the parking brake.
4. Always block the rear wheels on the downhill side.
71
Page 76
OPERATION
WARNING
Hauling Cargo
Overloading the vehicle or carrying or towing cargo improperly can alter vehicle
handling and may cause loss of control or brake instability, which can result in
serious injury or death. Always follow these precautions when hauling cargo:
Never carry cargo on the rear rack when operating the ATV in the 2-up mode
with a passenger.
REDUCE SPEED AND ALLOW GREATER DISTANCES FOR BRAKING
WHEN HAULING CARGO.
NEVER EXCEED THE MAXIMUM WEIGHT CAPACITY of the vehicle. When
determining the weight you are adding to the vehicle, include the weight of the
operator, passenger, accessories, loads in the rack or box and the load on the
trailer tongue. The combined weight of these items must not exceed the
maximum weight capacity .
CARGO WEIGHT DISTRIBUTION should be 1/3 on the front rack and 2/3 on
the rear rack. When operating over rough or hilly terrain, reduce speed and
cargo to maintain stable driving conditions. Carrying loads on only one rack
increases the possibility of vehicle overturn.
CARRY LOADS AS LOW ON THE RACKS AS POSSIBLE. Carrying loads high
on the racks raises the center of gravity of the vehicle and creates a less stable
operating condition.
SECURE ALL LOADS BEFORE OPERATING. Unsecured loads can create
unstable operating conditions, which could result in loss of control of the vehicle.
OPERATE ONLY WITH STABLE AND SAFELY ARRANGED LOADS. When
handling off-centered loads that cannot be centered, securely fasten the load
and operate with extra caution. Always attach the tow load to the hitch point
designated for your vehicle.
HEAVY LOADS CAN CAUSE BRAKING AND CONTROL PROBLEMS. Use
extreme caution when applying brakes with a loaded vehicle. Avoid terrain or
situations that may require backing downhill.
USE EXTREME CAUTION when operating with loads that extend over the rack
sides. Stability and maneuverability may be adversely affected, causing the
vehicle to overturn.
DO NOT BLOCK THE FRONT HEADLIGHT BEAM when carrying loads on the
front rack.
DO NOT TRAVEL FASTER THAN THE RECOMMENDED SPEEDS. The
vehicle should never exceed 10 mph (16 kph) while towing a load on a level
surface. Vehicle speed should never exceed 5 mph (8 kph) when towing loads in
rough terrain, while cornering, or while ascending or descending a hill.
72
Page 77
OPERATION
2/3
1/3
Hauling Cargo
Never exceed the weight capacities
specified for your ATV on warning
labels and in the specifications section of this manual.
1. Cargo weight should be evenly
distributed (1/3 on the front
rack and 2/3 on the rear rack)
and mounted as low as possible.
2. When operating over rough or
hilly terrain, reduce speed and
cargo weight to maintain stable
driving conditions.
3. Do not obstruct the headlight beam with cargo.
4. Slow down.
5. Use low forward gear when hauling or towing heavy cargo to
extend belt life.
6. Always operate the vehicle with extreme caution whenever hauling
or towing loads. Balance, handling, and control may be affected.
73
Page 78
OPERATION
Maximum
4" (10 cm)
Hauling Cargo
Towing Loads
Always attach a towed load to the hitch point. Remove the hitch from
the ATV when not towing a trailer. If towing a load, reduce rear rack
cargo weight by the amount of tongue weight.
• The combination of rear rack cargo weight and tongue weight must
not exceed the rear rack capacity.
• The total load (operator, passenger, accessories, cargo and weight on
hitch) must not exceed the maximum weight capacity of the vehicle.
NOTICE: Using an improper hitch or exceeding
Maximum Towing Capacities
Do not exceed maximum towing capacities. Avoid towing on inclines.
Maximum Towed Load (Level Ground)1500 lbs. (680 kg)1500 lbs. (680 kg)
Maximum Vertical Hitch Weight150 lbs. (68 kg)150 lbs. (68 kg)
the maximum tongue weight capacity
can result in serious damage to the
vehicle and will void your ATV
warranty. Never install a hitch longer
than 4" (10 cm). Never install
automotive accessories on your
POLARIS ATV. Always install
POLARIS-approved (or equivalent)
accessories designed for ATV use.
550850
74
Page 79
EMISSION CONTROL SYSTEMS
Noise Emission Control System
Do not modify the engine, intake or exhaust components, as doing so
may affect compliance with U.S.A. EPA noise control requirements (40
CFR 205) and local noise level requirements.
Operation on Public Lands in the U.S.A.
Your POLARIS vehicle has a spark arrestor that was tested and qualified to be in accordance with the USFS standard 5100-1c. Federal law
requires that this spark arrestor be installed and functional when the
vehicle is operated on public lands.
Operation of off-road vehicles on public lands in the U.S.A. is regulated
by 43 CFR 420. Violations are subject to monetary penalties. Federal
regulations can be viewed online at www.gpoaccess.gov/ecfr/.
Crankcase Emission Control System
This engine is equipped with a closed crankcase system. Blow-by gases
are forced back to the combustion chamber by the intake system. All
exhaust gases exit through the exhaust system.
Exhaust Emission Control System
Exhaust emissions are controlled by engine design. An electronic fuel
injection (EFI) system controls fuel delivery. The engine and EFI components are set at the factory for optimal performance and are not
adjustable.
The vehicle compliance labels can be found on the frame tubing of the
vehicle.
Electromagnetic Interference
This spark ignition system complies with Canadian standard ICES-002.
This vehicle complies with the EMC requirements of European direc-
tives 97/24/EC and 2004/108/EC.
Non-ionizing Radiation: This vehicle emits some electromagnetic
energy. People with active or non-active implantable medical devices
(such as heart monitoring or controlling devices) should review the limitations of their device and the applicable electromagnetic standards and
directives that apply to this vehicle.
75
Page 80
MAINTENANCE
Periodic Maintenance Chart
Careful periodic maintenance will help keep your vehicle in safe, reliable condition. Inspect, clean, lubricate, adjust and replace parts as necessary. When inspection reveals the need for replacement parts, use
genuine POLARIS parts available from your POLARIS dealer. Record
maintenance and service in the Maintenance Log beginning on page
144.
Service and adjustments are important for proper vehicle operation. If
you're not familiar with safe service and adjustment procedures, have a
qualified dealer perform these operations.
Maintenance intervals in the following chart are based upon average
riding conditions and an average vehicle speed of approximately 10
miles per hour. Vehicles subjected to severe use must be inspected and
serviced more frequently.
Severe Use Definition
• Frequent immersion in mud, water or sand
• Racing or race-style high RPM use
• Prolonged low speed, heavy load operation
• Extended idle
• Short trip cold weather operation
Pay special attention to the oil level. A rise in oil level during cold
weather can indicate contaminants collecting in the oil sump or crankcase. Change oil immediately if the oil level begins to rise. Monitor the
oil level, and if it continues to rise, discontinue use and determine the
cause or see your dealer.
76
Page 81
MAINTENANCE
WARNING
Periodic Maintenance Chart
Improperly performing the procedures marked with a n could result in
component failure and cause an accident, which may result in serious injury or
death. Always have an authorized POLARIS dealer perform these services.
Maintenance Chart Key
X Perform more often for vehicles subjected to severe use.
EEmission-related service (Failure to conduct this maintenance will
not void the emissions warranty but may affect emissions.)
nHave an authorized POLARIS dealer perform these services.
77
Page 82
MAINTENANCE
Periodic Maintenance Chart
Perform all services at whichever maintenance interval is reached first.
ItemMaintenance Interval
Steering-Pre-Ride-Make adjustments as
Front suspension-Pre-RideRear suspension-Pre-RideTires-Pre-RideBrake fluid level-Pre-RideBrake lever travel-Pre-RideBrake system-Pre-RidePassenger seat
replace if necessary
ing/air leaks
needed
seasonally; pressure test
system yearly
surfaces
lines, filter, pump; replace
lines every two years
security; apply dielectric
grease to connectors
subjected to water, mud, etc.
parts
Inspect; adjust
when parts are replaced
Remarks
79
Page 84
MAINTENANCE
Front Prop Shaft
Yoke
Front
Lubrication Guide
Check and lubricate all components at the intervals outlined in the Periodic Maintenance Chart beginning on page 76. Items not listed in the
chart should be lubricated at the General Lubrication interval.
The a-arms and upper control arms are lubricated at the factory, and no
additional lubrication will be needed. However, if these components are
subjected to severe use, grease zerks have been provided for additional
lubrication at the user's discretion.
Grease fittings (3 pumps maximum) every 500 miles,
before long periods of storage, or after pressure
washing or submerging.
Grease fittings after extreme use or if suspension
becomes squeaky.
Fill Plug
Torque
---15-17 ft. lbs.
---12 ft. lbs.
10-14 ft. lbs.
(14-19 Nm)
8-10 ft. lbs.
(11-14 Nm)
10-14 ft. lbs.
(14-19 Nm)
Drain Plug
Torque
(20-23 Nm)
(16 Nm)
10-14 ft. lbs.
(14-19 Nm)
11 ft. lbs.
(15 Nm)
10-14 ft. lbs.
(14-19 Nm)
Inspection
Procedure
Page 81.
Page 81.
Page 84.
Page 86.
Page 89.
80
Page 85
MAINTENANCE
Dipstick
Full
Add
850
FullAdd
550
Engine Oil
Oil Recommendations
POLARIS recommends the use of POLARIS PS-4 PLUS Performance
Synthetic 2W-50 4-cycle oil or a similar oil for this engine. See the table
on page 80 for fluid recommendations, capacities and plug torques.
Oil may need to be changed more frequently if POLARIS oil is not
used. Always use 2W-50 oil. Follow the manufacturer's recommendations for ambient temperature operation. See page 131 for the part numbers of POLARIS products.
NOTICE: Mixing brands or using a non-recommended oil may cause serious
Oil Level
Check the oil level when the
engine is cold. Never check the
oil with the engine running.
1. Position the vehicle on a
2. Access the oil dipstick and
3. Reinstall and tighten the dip-
4. Remove the dipstick and
5. Add the recommended fluid
6. Reinstall and tighten the dip-
engine damage. Always use the recommended oil. Never substitute
or mix oil brands.
level surface.
fill tube from the left side of
the ATV. Remove the dipstick. Wipe it dry with a
clean cloth.
stick.
check the oil level.
as needed. Maintain the oil
level in the safe range
between the FULL and ADD
marks. Do not overfill.
stick.
81
Page 86
MAINTENANCE
550 Drain
Plug
to front
850 Drain
Plug
Filter Access
Engine Oil
Oil and Filter Change
See the table on page 80 for fluid recommendations, capacities and plug
torques. Always change the oil and filter at the intervals outlined in the
Periodic Maintenance Chart beginning on page 76. Always change the
oil filter whenever changing oil.
1. Position the vehicle on a level surface.
2. Start the engine. Allow it to warm up at idle for two to three min-
utes.
3. Stop the engine.
4. Clean the area around the drain plug.
5. Place a drain pan under the crankcase.
6. Remove the drain plug. Allow the oil to drain completely.
CAUTION! Hot oil can cause burns to skin. Do not allow hot oil to contact skin.
7. Install a new sealing washer on the drain plug. The sealing surfaces
on drain plug and crankcase should be clean and free of burrs, nicks
or scratches.
8. Reinstall the drain plug. Torque to specification.
82
Page 87
MAINTENANCE
Oil Filter
850550
Engine Oil
Oil and Filter Change
9. Place shop towels beneath
the oil filter. Using an oil filter wrench (available from
your POLARIS dealer), turn
the filter counter-clockwise
to remove it.
10. Using a clean dry cloth, clean
the filter sealing surface on
the crankcase.
11. Lubricate the o-ring on the
new filter with a film of fresh
engine oil. Check to make
sure the o-ring is in good
condition.
12. Install the new filter and rotate it clockwise by hand until the filter
gasket contacts the sealing surface, then turn it an additional 1/2
turn.
13. Remove the dipstick. Add the proper amount of the recommended
oil. Do not overfill.
14. Reinstall the dipstick.
15. Place the transmission in PARK.
16. Lock the parking brake.
17. Start the engine. Allow it to idle for one to two minutes.
18. Stop the engine.
19. Check for leaks.
20. Check the oil level. Add oil as needed to bring the level to the upper
mark on the dipstick.
21. Dispose of used filter and oil properly.
83
Page 88
MAINTENANCE
Drain Plug
Fill Plug
Fill
Level
Transmission Oil
POLARIS recommends the use of POLARIS AGL PLUS Transmission
Fluid for this transmission. See the table on page 80 for fluid recommendations, capacities and plug torques. Always check and change the
transmission oil at the intervals outlined in the Periodic Maintenance
Chart beginning on page 76. See page 131 for the part numbers of
POLARIS products.
Maintain the oil level at the bottom of the fill plug hole. The fill
plug is located on the right side of
the ATV behind the footwell. The
drain plug is located on the bottom
rear side of the gearcase.
Oil Check
1. Remove the footwell (see
page 97).
2. Remove the fill plug. Check
the oil level.
3. Add the recommended fluid
as needed to bring the level to
the bottom of the fill hole
threads.
4. Reinstall the fill plug. Torque to specification.
5. Reinstall the footwell.
84
Page 89
MAINTENANCE
Transmission Oil
Oil Change
1. Remove the footwell.
2. Place a drain pan under the gearcase. Remove the drain plug. Allow
the oil to drain completely.
3. Clean and reinstall the drain plug. Torque to specification.
4. Remove the fill plug. Add the proper amount of the recommended
oil.
5. Reinstall the fill plug. Torque to specification.
6. Check for leaks.
7. Reinstall the footwell.
8. Dispose of used oil properly.
85
Page 90
MAINTENANCE
Drain Plug
Fill
Plug
Fill
Level
Front Gearcase (Demand Drive) Fluid
See the table on page 80 for fluid recommendations, capacities and plug
torques. Always check and change the demand drive fluid at the intervals outlined in the Periodic Maintenance Chart beginning on page 76.
See page 131 for the part numbers of POLARIS products.
Change the front gearcase fluid every 25 hours if the ADC unit is
exposed to extreme use. Extreme use includes any of the following:
• operation in ADC mode for prolonged periods
• constant ADC operation on hilly or mountainous terrain
• ADC is the primary mode of all-wheel-drive operation
Tip: If the front gearcase is make s excessive noise during ADC operation,
change the demand drive fluid. If the noise continues, please see your
POLARIS dealer for service.
Use the recommended fluid. Use of other fluids may result in improper
operation of components. Maintain the fluid level at the bottom of the
fill hole threads. The fill plug is located on the right side of the demand
drive unit. The drain plug is located on the bottom right side of the unit.
Fluid Check
1. Position the vehicle on a level sur-
face. Remove the fill plug. Check
the fluid level.
2. Add the recommended fluid as
needed to bring the level to the bottom of the fill hole threads.
3. Reinstall the fill plug. Torque to
specification.
Fluid Change
1. Position the vehicle on a level sur-
face. Remove the fill plug.
2. Place a drain pan under the demand drive unit. Remove the drain
plug. Allow the fluid to drain completely.
3. Clean and reinstall the drain plug. Torque to specification.
4. Add the proper amount of the recommended fluid.
5. Reinstall the fill plug. Torque to specification.
6. Check for leaks. Dispose of used fluid properly.
86
Page 91
MAINTENANCE
ADC Fluid Reservoir
Active Descent Control (ADC) Fluid
Check and change the ADC fluid at the intervals outlined in the Periodic
Maintenance Chart beginning on page 76.
We recommend the use of POLARIS Demand Drive Plus Fluid for the
ADC unit. Maintain the fluid level between the minimum and maximum
marks on the reservoir. See page 131 for the part numbers of POLARIS
products.
NOTICE: Do not use brake fluid. Brake fluid will damage rubber components in
Fluid Check
1. Access the reservoir under
2. View the fluid level in the
3. If the level is below the
4. Reinstall the cap.
5. Close and secure the front
the hydraulic system.
the front box. See page 36.
reservoir.
minimum mark, remove
the cap and add the
recommended fluid.
box and cover.
87
Page 92
MAINTENANCE
Bleeder
Screw
Cap
Bleeder
Valve
Screw
Active Descent Control (ADC) Fluid
Fluid Change
1. Position the vehicle on a level
surface. Before performing the
fluid change, allow the vehicle
to sit for at least 30 minutes.
2. Thoroughly clean the areas
around and on the ADC
reservoir and bleeder valves
(one on each side of the
differential).
3. Remove the reservoir cap and
diaphragm assembly. Use a
shop towel or suction tool to
remove debris from the fluid
and reservoir. Debris in the
reservoir may result in
inadequate bleeding and
reduced performance of the
system.
4. Fill the reservoir to the maximum line with fresh fluid.
5. Remove the protective caps from the bleeder valves.
6. Slowly loosen one of the bleeder valve screws (turn counter-clock-
wise) and allow fluid and trapped air to flow from the fitting.
Tighten the screw when clean fluid begins to flow. Repeat this step
for the remaining valve.
IMPORTANT: Close the bleeder valve screws before the reservoir fluid level
drops below the minimum fill line. Adding fluid to an empty reservoir will result in
trapped air. If the level drops below the minimum line, add fluid to the maximum
line and repeat step 6 before proceeding.
7. Torque the bleeder valve screws to 80 in. lbs. (9 Nm). Reinstall the
bleeder valve caps.
8. Add fresh ADC fluid to the reservoir until the level is between the
minimum and maximum marks. Make sure the reservoir is free of
debris.
9. Reinstall the cap securely. Clean up any drips or spills.
88
Page 93
MAINTENANCE
Drain Plug
Fill Plug
Fill
Level
Rear Gearcase Oil
See the table on page 80 for fluid recommendations, capacities and plug
torques. Always check and change the rear gearcase oil at the intervals
outlined in the Periodic Maintenance Chart beginning on page 76. See
page 131 for the part numbers of POLARIS products.
The fill plug is located on the
rear of the gearcase. The drain
plug is located on the bottom
of the gearcase.
Maintain the fluid level at the
bottom of the fill hole threads.
Do not overfill.
Oil Check
1. Position the vehicle on a
level surface.
2. Remove the fill plug.
Check the oil level.
3. Add the recommended oil
as needed to bring the
level to the bottom of the
fill hole threads. Do not overfill.
4. Reinstall the fill plug. Torque to specification.
Oil Change
1. Position the vehicle on a level surface.
2. Place a drain pan under the drain hole.
3. Remove the drain plug. Allow the oil to drain completely.
4. Clean and reinstall the drain plug with a new sealing washer. T orque
to specification.
5. Remove the fill plug. Add the proper amount of the recommended
oil. Do not overfill.
6. Reinstall the fill plug. Torque to specification.
7. Check for leaks.
8. Dispose of used oil properly.
89
Page 94
MAINTENANCE
Clean
Often
Power Steering Unit
If your model is equipped with
power steering, frequently clean
the areas around and on the
power steering unit to allow
proper cooling. Clean these areas
thoroughly.
Steering Assembly
The steering assembly of the ATV should be checked periodically for
loose nuts and bolts. If loose nuts and bolts are found, see your
POLARIS dealer for service before operating the vehicle.
Cooling System
The engine coolant level is controlled, or maintained, by the recovery
system. The recovery system components are the recovery bottle, the
radiator filler neck, the radiator pressure cap and the connecting hose.
As coolant operating temperature increases, the expanding (heated)
excess coolant is forced out of the engine, past the pressure cap, and into
the recovery bottle. As engine coolant temperature decreases the contracting (cooled) coolant is drawn back up from the bottle, past the pressure cap, and into the radiator.
Some coolant level drop on new vehicles is normal as the system is
purging itself of trapped air. Check the coolant level and maintain as
recommended by adding coolant to the recovery bottle.
POLARIS recommends the use of POLARIS Premium 60/40 antifreeze/coolant or a 50/50 mixture of high quality aluminum compatible
anti-freeze/coolant and distilled water. POLARIS Premium 60/40 is
already premixed and ready to use. Do not dilute with water. See page
131 for the part numbers of POLARIS products.
Always follow the manufacturer's mixing recommendations for the
freeze protection required in your area.
90
Page 95
MAINTENANCE
Maximum
Mark
Minimum
Mark
Recovery
Bottle Cap
Cooling System
Recovery Bottle Coolant
The recovery bottle fluid level can be viewed from inside the front right
wheel well. Access the recovery bottle cap under the front box. See page
36.
1. View the fluid level in the bottle.
2. If the level is low , remove the bottle cap and add coolant as needed.
Maintain the coolant level between the minimum and maximum
marks on the bottle (when the fluid is cool).
3. Reinstall the cap.
4. Close and secure the front box and cover.
91
Page 96
MAINTENANCE
Radiator
Cap
Cooling System
Radiator Coolant
To ensure that the coolant maintains its ability to protect the engine,
POLARIS recommends that you drain the system completely every two
years and add a fresh mixture of antifreeze and water.
Replace the coolant any time the cooling system has been drained for
maintenance or repair . If the recovery bottle has run dr y, check the level
in the radiator. Add coolant as needed.
CAUTION! Escaping steam can cause burns. Never remove the pressure cap
while the engine is warm or hot. Always allow the engine to cool before
removing the pressure cap.
1. Access the pressure cap under the
front box. See page 36.
2. Remove the pressure cap.
3. Using a funnel, slowly add cool-
ant through the radiator filler
neck.
4. Reinstall the pressure cap. Use of
a non-standard pressure cap will
not allow the recovery system to
function properly. Contact your
dealer for the correct replacement
part.
5. Close and secure the front box and cover.
92
Page 97
MAINTENANCE
3/64" (1 mm)
Brakes
Hand Brake
The front and rear brakes are hydraulic disc brakes, activated by moving
the single brake lever toward the handlebar. These brakes are selfadjusting.
Under normal operation, the diaphragm extends into the reservoir as
fluid level drops. If the fluid level is low and the diaphragm is not
extended, a leak is likely and the diaphragm should be replaced. To
ensure proper diaphragm operation, always fill the reservoir as needed
whenever the cover is loosened or removed. Do not overfill.
WARNING! An over-full master cylinder may cause brake drag or brake lockup, which could result in serious injury or death. Maintain brake fluid at the
recommended level. Do not overfill.
The following checks are recommended to keep the brake system in
good operating condition. Check more often if brakes are used heavily
under normal operation.
1. Always keep brake fluid at an adequate
level. See page 30.
2. Check the brake system for fluid leaks.
3. Check the brakes for excessive travel or
spongy feel.
4. Check the friction pads for wear, damage
and looseness. Replace brake pads when
they are worn to 3/64" (1 mm).
5. Check the security and surface condition
of the disc.
Auxiliary Foot Brake
The hydraulic auxiliary brake system requires no adjustment. Check the
brake fluid level frequently for the auxiliary brake system. See page 32.
93
Page 98
MAINTENANCE
String
Stand
2
1
Toe Alignment
Use the following procedure to check the toe alignment of the vehicle.
The recommended toe alignment is 0" to 1/8" (0-3 mm).
WARNING! Severe injury or death can result from improper toe alignment and
adjustment. Do not attempt to adjust tie rod alignment. All tie rod adjustments
should be performed by an authorized POLARIS dealer.
1. Position the vehicle on a
level surface.
2. Place the handlebars in a
straight-ahead position.
3. Tie a length of string
between two stands as
shown in the illustration.
Position the stands so
that the string is flush
with the side of the rear
tire. If available, you
may use a long straightedge instead of string.
4. Measure the distance
from the string to the
rim at the front (1) and
rear (2) of the front rim.
The rear measurement
should be 1.5 mm more than the front measurement on each side of
the vehicle to obtain the recommended 0" to 1/8" (0-3 mm) toe out
alignment.
5. Repeat the measurement procedure on the other side of the vehicle.
6. If you discover improper alignment, see your POLARIS dealer for
service.
94
Page 99
MAINTENANCE
Seats
Passenger Seat Removal
1. Pull the latch at the rear of the seat.
2. Pivot the rear of the seat upward and
remove the front legs of the seat base
from the frame.
3. To reinstall the seat, position the
front legs of the seat base under the
frame. Pivot the rear of the seat
downward onto the latch. Press
down firmly on the seat pad until the
latch clicks. Test the seat latch by attempting to pull the seat
upward.
Passenger Seat Backrest Adjustments
The passenger backrest can be adjusted horizontally and vertically.
1. Unzip the two zippers at the bot-
tom of the backrest pad. Lift the
pad upward to remove it from the
backrest frame.
2. To adjust the backrest forward or
rearward, loosen the top adjuster
bolt. Pivot the adjuster forward or
rearward to one of the three
adjustment positions and tighten
the bolt.
3. To adjust the backrest upward or
downward, loosen the four vertical adjustment screws on the front
side of the backrest frame. Slide
the backrest upward or downward
to the desired position and tighten
the screws.
4. Reinstall the backrest pad.
95
Page 100
MAINTENANCE
Seats
Passenger Seat Suspension
1. Remove the passenger seat.
2. Remove the fastener retaining the
passenger seat shock to the passenger
seat support.
3. Pivot the seat support upward to
access the lower shock fastener.
Remove the lower shock fastener.
4. Remove the shock from the vehicle.
If adjustment is necessary, use a suitable pliers or spanner wrench. Adjust
the shock to the desired spring preload. Rotate the adjustment cam to
the left to increase preload.
5. Reinstall the shock.
6. Torque the upper and lower shock
fasteners to 38 ft. lbs. (51 Nm).
7. Reinstall the passenger seat.
Operator Seat Removal
1. Remove the passenger
seat. See page 95.
2. Grasp one side of the oper-
ator’s seat near the rear
edge.
3. Pull upward abruptly to
disengage the under-seat
fasteners.
4. Remove the seat.
96
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.