HANDLEBAR BAG WITH PHONE CHARGER
KIT
P/N 2883687; 2883786
APPLICATION
Verify accessory fitment at Polaris.com.
BEFORE YOU BEGIN
Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
KIT CONTENTS
This Kit includes:
REF QTY PART DESCRIPTION KIT PN
2883687
1 1 Harness - 850 2414491 2414491
2 1 Harness - Titan
3 1 Harness - 600/800 2414585 2414585
4 1 Bag - HB USB Charge 2688874
1 Instructions 9928802 9928802
Instr 9928802 Rev 01 2018-06 Page 1 of 8
-
-
KIT PN
2883786
2414584
2688951
TOOLS REQUIRED
• Safety Glasses
• Pliers, Push Pin Rivet
• Pliers, Side Cutting
• Socket Set, Metric
• Socket Set, Torx®Bit
• Torque Wrench
• Wrench Set, Metric
IMPORTANT
Your HANDLEBAR BAG WITH PHONE CHARGER KIT is exclusively designed for your vehicle. Please read the
installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of
debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the
sequence shown.
ASSEMBLY TIME
Approximately 30 minutes
NOTE
Additional time may be required for optional steps, or
to accommodate other installed accessories.
INSTALLATION INSTRUCTIONS
CAUTION
BEFORE STARTING INSTALLATION, always
ensure vehicle is properly secured on a flat stable
surface to avoid accidental tipping, unwanted
movement and to prevent personal injury and/or
damage to equipment. Turn key to “OFF” position
and remove from vehicle.
2. REMOVE HOOD.
a. Slightly lift the rear of the hood assembly to
gain access to the main hood harness
connector
chassis harness connector
the cable tie
the chassis and remove hood.
and disconnect from main
A
. If applicable, cut
B
securing the hood harness to
C
NOTE
Images shown may vary from your specific model
vehicle. Installation steps are similar between
models unless otherwise specified.
1. REMOVE SIDE PANELS.
Instr 9928802 Rev 01 2018-06 Page 2 of 8
3. REMOVE UPPER INTAKE PLENUM.
a. To do so, first remove the two dart clips
cable tie
tube
C
that fasten the intermediate intake
B
to the upper intake plenum..
A
and
c. Remove the two screwsFthat attach the
upper intake plenum
along with the two dart clips
complete, remove upper intake plenum
to the over-structure
H
as shown. Once
G
H
.
b. Next, unplug the two electrical connectors
from the ECUE.
D
Instr 9928802 Rev 01 2018-06 Page 3 of 8
4. REMOVE CONSOLE.
5. SELECT HARNESS.
a. Remove two dart clips
with clutch tool
and slide the console rearward leaving the
starter rope attached.
and dart clipCfrom left side
B
on right side along
A
a. For 850 models use harness
image.
• Connector (1a) will get connected to the
chassis harness.
• Connector (1b) is a spare connector for use
with additional accessories.
• Connectors (1c) connect to the USB
terminals on the bag.
. See detailed
q
The console should now be in a position to
allow you to access the fabric electrical
connections bag in the following steps.
b. For Titan™™models use harnessw. See
detailed image.
• Connector (2a) will get connected to the chassis
harness.
• Connector (2b) is a spare connector for use with
additional accessories.
• Connectors (2c) connect to the USB terminals on
the bag.
Instr 9928802 Rev 01 2018-06 Page 4 of 8
c. For 600/800 models use harnesse.
• Connector (3a) will get connected to the chassis
harness.
• Connector (3b) is a spare connector for use with
additional accessories.
• Connectors (3c) connect to the USB terminals on
the bag.
b. Place bag over top of handlebars being sure
wires are routed downward along the
handlebar post.
c. Secure bag onto handlebars with the two hook
and loop fastener panels on each side of bag.
6. MOUNT HANDLEBAR BAG.
a. Ensure the USB harness connections are
connected to USB terminals on the back of the
bag. Place bag into position as shown.
Instr 9928802 Rev 01 2018-06 Page 5 of 8
7. ROUTE AND CONNECT HARNESS WIRES.
b. Titan Model
NOTE
Electrical connections and routing vary slightly
between models. Follow steps for you specific model
for proper installation.
a. 850 Models
i. Route USB harness wires down along
steering post to the electrical connections
bag
located under the console.
B
i. Route USB harness wires down along
steering post to the electrical connections
bag
bag and connect USB harness connection
(2A) to chassis harness connector
shown.
located under the console. Open
B
C
as
Open bag and connect USB harness
connection (1A) to chassis harness
connector
as shown.
C
c. 600/800 Models
i. Route USB harness wires down along
steering post then along the left hand overstructure tube to connector
the left hand shock tower. Connect USB
harness connection (3A) to chassis harness
connector
as shown.
C
C
located near
Instr 9928802 Rev 01 2018-06 Page 6 of 8
8. REINSTALL CONSOLE.
9. REINSTALL UPPER INTAKE PLENUM.
a. Place console into original position and install
previously removed dart clips
along with the clutch tool
left side.
B
on right side
A
and dart clipCon
a. Carefully install upper intake plenum
into original position. Ensure the console tabs
are fully engaged into the slotsCon the
B
underside of the intake plenum.
NOTE
Be careful not to damage the intake screen while
installing upper intake plenum.
b. Install dart clipsDand fastenersEthat
secure the intake plenum
structure and torque fasteners
specification provided
to the over-
A
E
to
A
back
TORQUE
7 ft. lbs. (10 Nm)
Instr 9928802 Rev 01 2018-06 Page 7 of 8
c. Place intake tubeFback into position and
secure with previously removed dart clip
fasteners
lower portion of intake tube.
Ensure the mating joint between the upper intake
plenum and the intake tube is completely engaged
all the way around the mating joint. Failure to do so
may result in premature engine failure.
. Replace cable tieHto secure
G
IMPORTANT
10.REINSTALL HOOD.
a. Install hood being sure to connect the hood
harness
Replace cable tie
into position with hood latch fasteners.
11. REINSTALL SIDE PANELS.
a. After installing hood, install both side panels
making sure all hood latches and rubber straps
are fully secured.
and chassis harnessBconnection.
A
if applicable. Secure hood
C
d. Reconnect ECU by plugging the chassis
electrical harness connector
in the ECUK.
J
12.VERIFY WORK.
a. Check to ensure all tools are accounted for and
all steps have been completed.
FEEDBACK FORM
A feedback form has been created for the installer to provide any comments, questions
or concerns about the installation instructions. The form is viewable on mobile devices
by scanning the QR code or by clicking HERE if viewing on a PC.
FEEDBACK FORM
Instr 9928802 Rev 01 2018-06 Page 8 of 8
Loading...