POLARIS INTERACTIVE DIGITAL
DISPLAY KIT
P/N 2880495
APPLICATION
INSTALLATION OF THE DISPLAY INTO A PRO-RIDE MODEL
BEFORE YOU BEGIN
Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these
installation instructions for future reference and parts ordering information.
2
1
KIT CONTENTS
Ref Qty Part Description Part Number
1 1 Hood Harness 2412976
2 1 Key Switch, 3 POS 4012165
3 Panduit Strap 7080138
1 Panduit Strap, 160 x 7.6 7080492
2 Screw 7519145
1 Bracket 5261056
1 Instructions 9926329
TOOLS NEEDED
T40 Torx Side-Cutter 10 mm Socket
APPROXIMATE ASSEMBLY TIME
30 mins
P/N 9926329 Rev 01 01/15 Page 1 of 9
IMPORTANT
Your Polaris INTERACTIVE DIGITAL DISPLAY KIT is exclusively designed for your vehicle. Please
read the installation instructions thoroughly before beginning. Installation is easier if the vehicle
is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all
installation steps correctly in the sequence shown.
NOTE: Before beginning kit installation, remove the current gauge, hood harness (PN 2412552) and
key switch from vehicle. Follow the steps in Installation Instructions to install defrost bag
(PN 2879090), hood harness (PN 2412976), GPS, key switch (PN 4012165), and display on your
Pro-Ride or Indy.
INSTALLATION INSTRUCTIONS
1. Lock the parking brake.
2. Cut a hole (A) of size 1”X1” (25.4 mm X 25.4 mm) in
defrost bag. See gure.
3. Remove side panels.
A
4. Disconnect hood harness (B).
B
P/N 9926329 Rev 01 01/15 Page 2 of 9
5. Remove hood by removing two T40 torx bolts (C)
and two tufock plastic fasteners (D).
C
D
P/N 9926329 Rev 01 01/15 Page 3 of 9
6. Disconnect headlights (E), display (F) and key
switch (G).
E
F
G
7. Remove hood harness from right side.
8. Remove display by prying around the edges with your ngers and pushing up from underneath.
9. Remove key switch.
P/N 9926329 Rev 01 01/15 Page 4 of 9
10. Route GPS cable (H), display cable (I) and key
switch (J) in through the bottom of the bag.
11. Locate the hole (A) for GPS connector. Plug in
GPS Puck (K). Zip tie (L) is used to secure the GPS
puck.
H
I
J
A
P/N 9926329 Rev 01 01/15 Page 5 of 9
K
L
12. Install new key switch (2) into bag.
13. Plug in display (M) then install with rubber
grommet (N) by pushing evenly and rmly.
14. Install retaining bracket (P) on back side of gauge
with the two screws (Q) using a 10 mm socket.
M
2
N
Q
P
P/N 9926329 Rev 01 01/15 Page 6 of 9
15. Route harness (1) through old display hole to the
right, and connect headlights (E).
1
E
P/N 9926329 Rev 01 01/15 Page 7 of 9
16. Install hood without fasteners.
17. Install tufock plastic fastener (D) on either side of
the windshield.
18. Install rear bag mounts with T40 Torx bolts (C).
Torque to 7.4 ft. lbs. (10 Nm)
D
19. Install front bag mounts (R) by putting them in
between the windshield and the hood. Then
reinstall the plastic fasteners.
20. Connect hood harness plug.
C
R
P/N 9926329 Rev 01 01/15 Page 8 of 9
R
21. WITHOUT BATTERY:
• Disconnect white plug (S) near hood harness
and remove battery cable. Installation is done.
• If a battery is not installed the GPS puck will
loose satellite connection and take 30 to 120
seconds to establish connection. User will
not save tracks when GPS connection is not
established. Additionally, the user will not be
able to power the display when the engine is
not running.
22. WITH BATTERY:
• Route battery cable wire (T) along frame
following existing wires.
• Secure the cable with three zip ties (V) as
shown in the gures for the correct sled style.
• Zip ties connect to hood harness at two white
tape spots and one centered in between the
diode and fuse.
S
V
T
• Install negative and positive leads to battery.
V
P/N 9926329 Rev 01 01/15 Page 9 of 9
Loading...