POLAR-AIRE VF-9WFD Operating And Safety Instructions Manual
9 In. Digital Twin Window
Fan
Operating and Safety
Model No.: VF-9WFD
Instructions
- FOR HOUSEHOLD USE ONLY -
2
3
IMPORT
ANT SAFE
GU
ARDS
De
finitions
Whenever used, the following identify safety and
property
damage messages and designate a level of hazard seriousness.
- This is the safety alert symbol. It alerts you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
DANGER – Indicates an imminently hazardous situation, which, if not avoided,
will result in death or serious injury. Usage of this signal word is limited to the
most extreme situations.
WARNING – Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION – Indicates a potentially hazardous situation, which, if not avoided,
may result in minor/moderate injury.
NOTICE – Addresses practices not related to personal injury, such as product
and/or property damage.
Always follow basic safety precautions when using electrical
products, especially when children are present.
READ ALL
INS
TRUC
TIONS
BEFORE
USE.
DANGER --
To reduce the risk of electric shock:
Do not expose this product to rain, snow, or hail, as an electrocution hazard
exists and serious personal injury may occur.
Keep this product out of the reach of children and pets. This product is
not intended for use by children. Extra caution and close supervision are
necessary when using this product near children.
Do not plug/unplug the product into/from the electrical outlet with a wet
hand.
on the Control Panel and then pull directly on the plug; do not pull on the
power cord.
If using an extension cord with this product, the marked electrical rating of
the cord set or extension cord should be at least as great as the electrical
rating of the product.
if wires are exposed, if it malfunctions, if it is dropped or damaged, or if it is
dropped in or exposed to water. This product has no user-serviceable parts.
Do not attempt to examine or repair this product yourself. Only qualified
service personnel should perform any servicing; take the product to the
appliance repair shop of your choice for inspection and repair.
WARNING--
personal injury:
Always ensure the product is unplugged from the electrical outlet before
servicing, relocating, or cleaning it. Always unplug the product from the
electrical outlet when it is not in use or will be left unattended.
Do not operate this product with any solid-state speed control device.
Keep hands, hair, and clothing away from moving Blades during operation.
Do not immerse the product, power cord, or plug in water or other liquids.
To disconnect the product from an electrical outlet, press the Power Button
To reduce the risk of fire, electric shock, or serious
Do not operate the product if it has a damaged or cut power cord or plug,
4
5
CAUTION--
To reduce the risk of personal injury:
This product is intended solely for non-commercial, non-industrial, indoor,
household use in circulating air; do not use outdoors or for any other
purpose than intended.
Do not hang or wall-mount this product.
Do not run the power cord under carpeting, throw rugs, runners, or similar
coverings. Arrange the power cord away from traffic areas and where it will
not be tripped over.
Always operate the product on a flat, level, stable surface.
Parts
Expandable
panel
(inside)
Expandable
panel (inside)
WARNING:
This product has a polarized plug (one blade
is wider than the other). To reduce the risk of electric shock,
this plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not modify the plug
in any way.
Snap-on
Foot
As a floor or table fan:
Intake/
Exhaust/
Exchange
Switch
Power
button
Speed
Control
button
Thermostat
Control
button
Snap-on
Foot
NOTE: This product employs overload protection (fuse). A blown fuse indicates
an overload or short-circuit situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing instructions (follow product
marking for proper fuse rating) and check the product. If the replacement fuse
blows, a short-circuit may be present and the product should be discarded or
returned to a qualified service facility for examination and/or repair.
1. Slide the Snap-on Feet onto the edged slots,
located on the bottom of the Fan, until
they securely snap into place (see Fig.
1).
2. Place the Fan on a flat, level, stable
surface.
As a window fan:
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
NOTICE:
Do not set this product in a window that opens and closes
horizontally (side-to-side), as product damage may result.
To Set Up
Window Sash Holder
6
7
NOTES:
Remove Snap-on Feet when using the product as a window fan.
This product is designed to fit double-hung, casement, or vertically-sliding
windows.
Minimum window space opening is 23 inches (58 cm) x 11 inches (28 cm).
1. Ensure all four LOCK/UNLOCK Switches
for the Expandable Panels (see Fig. 2)
are set to the UNLOCK position.
2.
Open the window where the fan is
to be placed. Raise the lower sash to
make an opening of at least 11 inches
(28 cm) high.
3. Center the Fan on the windowsill in
the window opening with the Control
Panel facing the inside of the room.
NOTE: Make sure the lower edge of the Fan is positioned over the
windowsill cap.
4. Grasp the Fan handle and gently lower the window sash onto the top
edge of the Fan.
NOTE: Make sure the window sash rests between the Sash Holders
protruding from the top edge of the Fan.
5. Pull out the Expandable Panels so they reach the side edges of the
window.
6.
Once the fan is securely in place, slide all four LOCK/UNLOCK Switches to
the LOCK position.
WARNING: Do not lift the sash of a double-hung window while the Fan
is in operation, as there may be a risk of serious personal injury and/or
product damage.
To Use
1.
Plug the Fan into a standard 120-volt AC electrical outlet, the fan will stay on
standby mode.
2. Choose an airflow direction by sliding the FRESH AIR/EXHAUST Switches to the
desired positions.
- Exhaust: Air is pushed from inside the room to the outside.
- Air Exchange: One Fan is set on “Intake”, pulling fresh air into the room,
while the other Fan is set on “Exhaust”, simultaneously pushing stale air
from inside the room to the outside.
3.
To turn on the fan, press the power button( ) located on the left side of the
control panel. The fan will start on "HIGH" speed (Default Setting), and
"HIGH" speed indication light illuminates. Press the fan speed control button
( ) located on the right side of the control panel repeatedly to change fan
speed from "HIGH-MED-LOW", the indication light will illuminate accordingly.
Thermostat default setting is "OFF", three temperature indication lights are
"OFF".
60F: Press the Thermostat Control Button ( ) once.
75F: Press the Thermostat Control Button ( ) twice.
90F: Press the Thermostat Control Button ( ) a third time.
The temperature indication light will illuminate accordingly. Press the
Temperature Control Button a fourth time to turn the temperature feature off,
and all temperature indication lights will turn off.
NOTE: The fan will turn off if the room temperature drops below setting and
will turn on again if the room temperature climbs above setting.
WARNING: Do not expose this product to rain, snow, or hail, as an electrocution
hazard exists and serious personal injury and/or product damage may occur.
NOTICE:
Exchange) while the Fan is operating.
Never change the airflow direction (Intake, Exhaust, or Air
NOTES:
- Intake: Air is pulled into the room from the outside.
THERMOSTAT
4.
Choose from 60F, 75F or 90F settings by performing the following function:
8
9
5. To turn off the Fan, press the Power Button a second time, and then unplug
the Fan from the electrical outlet.
CAUTION:
Always unplug the product from the electrical outlet when it is
not in use or will be left unattended.
User Servicing Instructions
WARNING:
Always ensure the product is unplugged from the electrical outlet
before servicing, relocating, cleaning, or storing it.
This product is permanently lubricated at the factory before shipping and will
not require further lubrication for the life of the product.
WARNING: Additional lubrication of motor parts could increase the risk of a
fire hazard.
Clean the exterior surfaces only by wiping with a soft, damp cloth. Dust can
be removed from the Front/Rear Guards using a small vacuum.
WARNING: Do not use abrasive cleaners/pads to clean the product, and do
not allow water or other liquids to enter the interior of the product.
NOTICE: Do not disassemble the product for cleaning of internal parts, as
doing so may result in product damage and will void the warranty.
Make sure the product is completely dry before the next use.
Store the product with these instructions in the original box in a cool, dry
place.
3. Using a small flat blade screwdriver, carefully remove the fuse by prying it up
from the end closest to the cord.
4. Replace the fuse with a 2.5 amp, 125-volt fuse (not included).
To Replace Fuse:
1. Grasp plug and remove it from the receptacle
or other outlet device.
2.
Open the fuse compartment cover on top of
the plug by sliding it toward the blades.
WARNING:
5. Close the fuse compartment cover by sliding it away from the blades.
Risk of fire. Use a 2.5 amp, 125-volt fuse only.
Electrical Specifications
Voltage Frequency Wattage
120VAC
60Hz 60W
CAUTION:
power cord.
Do not unplug by pulling on the
Loading...