Poker PK900-IC827, PK900-IC822 User Manual
Model:PK900-IC827
PK900-IC822
User’s Manual for Smart Constant Speed Dome Camera
Please read the manual carefully before installing and using the unit.
Table of Contents
1
Part I: Introduction
1.1 Instructions ---------------------------------------------------------------------- 3
1.2 Characteristics ----------------------------------------------------------------- 4
1.3 Main Technical Data -------------------------- ------ ---- ---- ----- -- ------ ---- 5
1.4 Installation method and ancillary components ------------------------ 6
Part II: Installation procedures
2.1 Out shape and installation size ------------------------------------------- 7
2.2 Installation of the camera -------------------------------------------------- 11
2.3 Connection of the camera and the housing --------------------------- 13
2.4 Installation of the transparent cover ----------------------------------- 16
2.5 Installation of the Housing and the Bracket -------------------------- 19
2.6 Installation of the Bracket ------------------------------------------------- 20
2.7 Fix the 7” and 9” Dome Camera ---------------------------------------- 22
2.8 Fix the 7” and 9” Semi Dome Camera -------------------------------- 23
2.9 Connecting Power cables and signal cables ------------------------ 25
Part III: Setup of the Functions of the dome camera
3.1 Setup of Address, Communication Protocol, Baudrate and Running Speed
------------------------------------------------------------------------------------27
3.2 Power on and Working state examination -- ------------------------ 34
3.3 Table of the Setup of the functions -------------------------------------34
3.4 Set up and Preview the preset positions ----------------------------------- 35
3.5 Setup and running of Tour group --------------------------------------------- 36
2
3.6 Setup and running of Left and Right scanning------ ---------------------- 38
3.7 Start of the Pan/tilt’s 360° scanning ----------------------------------------- 38
3.8 Stop of the Auto Scanning ----------------------------------------------------- 43
3.9 Setup, Activating and Exitting of Default Position function ------------- 42
Part IV: Appendix
4.1 Constant temerature devices connecting sketch 1 ------------- 43
4.2 Constant temerature devices connecting sketch 2 ------------- 44
4.3 Trouble Shooting Table------------------------------------------------- 45
3
Part I: Introduction
1.1. Instructions:
We greatly appreciate your choosing our product!
As stated in the warranty instruction, when a breakdown occurs to
the properly used product, the product under warranty will be granted
free maintenance or spare parts replacement. Do not dismantle and
repair the unit without the company’s authorization.
Within one year from the purchase date, if any damage or
breakdown occurs to the product (excluding housing, bracket and
external wires) when it is properly used, we will provide free
maintenance or spare parts replacement after our technician confirms
the case.
No free maintenance under the following circumstances:
1. Damage or breakdown arising from the dismantling and repairing of
the unit without the company’s authorization;
2. Damage or breakdown arising from the transportation, loading or
unloading of the unit which is arranged by the customer;
3. Damage or breakdown arising from using and maintenance of the
unit without observing the instructions in the User’s Manual, including
damage or breakdown arising from crashing, crushing, and unit affected
with damp, liquids, corrosive or other man-made causes;
4. Damage or breakdown arising from inapplicable ambient
temperature or overloaded operation; surface abrasion or damage
emerging when the unit is being used;
5. Damage or breakdown arising from natural disasters and other
accidents.
Attention: To realize all the functions of the unit, a compatibility test
4
must be carried out before applying other manufacturer’s spare parts in
the system.
The Characteristics of Constant Speed Dome Camera:
1. Precise conductive slip-ring is adopted, with which pan 360° endless
running is realized and all-direction monitoring effect is realized,
cable-twisting problem as well as merely 355° pan problem which
generally happen with common constant speed domes are effectively
solved.
2. The operation is based on advanced stepper motors and driving
circuits, which ensures smooth running, long time consecutive working,
long lifespan and high reliability.
3. PCB board is very compact, most of the parts on the PCB board are
highly integrated and modulized, thus the possibility of trouble is greatly
reduced and the stability of the performance is ensured.
4. The design of the outer housing of the Constant Speed Dome Camera
is reasonable, elegant and practical. The outer housing can endure
long-term operation without distortion. And the installation of the unit is
fast, convenient and more human.
5. The function of Position Limiting is realized with photoelectrical
sensors, which avoids the limitations of traditional mechanical Position
Limiting and switch Position Limiting (the lifespan of the switch is 200
thousand times ON/OFF).
6. Left/right limiting positions can be set up on the dome camera panel, it
also can be set up through the keyboard in the controlling room, which
avoids the limitations that the limiting positions can be only set up from
the front terminals for common constant speed domes.
7. There are 4 levels of running speed optional for the unit: 6°,
9°,12°,15°/S, which can be adjusted according to actual conditions.
8. The built-in PCB panel supports multi mainstream protocols, and
5
many more protocols can be input according to the customer’s needs.
The Baud rate is also adjustable.
9. The unit adopts DC14V(15V) power supply and separates from it the
components that produce heat in the process of transformation, which
prolongs the durability of the unit. The unit possesses the functions of
anti-jamming and anti-crashing.
10. Two grades anti-lightening technology, which effectively improve the
anti-lightening and anti-interruption ability
11. If the unit is carrying out scanning or cruising function when the
power is off, it will automatically resume carrying out the function once
supply of power is on after the power-off state.
12. Support 16 preset positions, 1 tour, left & right scan, 360° scan.
13. The unit has one default position; the user can preset the default
position for a key monitoring area according to the actual conditions. If
not operated after 5 minutes, the dome camera will automatically
monitor the preset position.
Remarks：The function of item 13 can be realized only when the
protocol adopted supports the keyboard produced by this company. Also,
the user can include our protocols into the DVR or existing software.
1-3. Main Technical Data：
1. Electric Index
Power supply DC14V---15V (2A)
Dome motor DC14V---15V/0.5A
Camera lens motor DC12V/100mA
Camera power supply 12V/1A
Temperature controlling
devices ambient
Fan(≤50℃); heater (≥5℃)
6
Addresses range
1～63
Communication system RS485 bus controlling
Communication protocol supporting multi protocols
Baud rate
1200bps, 2400bps, 4800bps, 9600bps
adjustable, 1200bps can be replaced by
19200bps as per customer’s needs
Controlling device
video matrix, hard disk video recorder,
DVR controlling keyboard
Peset position quantity 16 preset positions
Auto Scan Support Left&right scan and 360° scan
Tour group quantity
1 group(16 preset positions can be
included)
Default position function Yes
2. Mechanical Index
Dome movement pan 360° endless, tilt 0°-90°
Dome speed
pan/tilt, Pan 6º/S, 9º/S, 12º/S, 15º/S
adjustable
Movement limiting position
pan adjustable within the dome
movement scope
Maxium acceptable size of
the compatible video camera
and lens
Nine-inch Constant Speed Dome
Camera：
170（L）×80（H）×70（W）mm
Seven-inch Constant Speed Dome
Camera
140（L）×70（H）×70（W）mm
3. Ambient Index
Ambient temperature
0ºC ～ 49ºC (without temperature
controlling devices)
-35ºC ～ 49ºC (with temperature
controlling devices)
Relative Humidity ≤90%RH
1-4. Styles of Installation and Ancillary Components (See Table 1)
7
Table 1: Styles of Installation and Ancillary Components
Ancillary
components
Product
The style of
installation
Bracket Power
temperaturecontrolling
device
cable
s
（
wit
h
conne
ctor
）
Wall-mount
installation
Wall-mount
bracket
Nine-inc
h
Outdoor
Pendant-mount
installation
Bracket
length:
20cm or 40cm
DC14V(15V)
/2A
Pendant-mount
installation
Bracket
length:
20cm or 40cm
Seven-i
nch
Outdoor
Wall-mount
installation
Wall-mount
bracket
DC14V(15V)
/2A
Nine-inc
h Indoor
Ceiling-mount
installation
Seven-i
nch
Indoor
Ceiling-mount
installation
No bracket;
Steel wire
rope to be
prepared by
the user
DC14V(15V)
/2A
Required when
the temperature
is below 0
℃
or
above 50
℃
power
cable
video
cable
RS48
5
cable
Part II: Installation Procedures
2-1. Outer shape and installation size.
1. Dimension of Seven-inch Constant Speed Dome Camera
8
2. Connect Lens Controlling Cable
Camera Lens Controlling Cable should be provided by the camera
supporter. Connect the camera controlling cable well according to the
corresponding relationship between the camera and the outlet of PCB
panel shown in the following table.
Controlling signal of the camera
lens
Corresponding outlet on PCB panel
Camera power supply +12VDC, GND
Lens Zoom ZOOM
Lens Focus FOCUS
Lens Iris IRIS
Lens Controlling public ground COM
9
3. Connect Video Cable
Connect BNC video outlet with the video output outlet of the camera,
then use the binding wire to tie the video cable inside the camera and
the lens cable into the hole beside the lens connecting outlet on the PCB
panel. After installing the camera, please set up communication protocol,
Baud rate, address, etc.
2-3. Connection of the Camera and the Housing of Dome Camera
Install the well-setup module equiped with camera into the housing.
Procedures shown below:
Step 1
Push the connecting ports end of the power, video and controlling
integrated cable through the central hole of the peg-board, and then fix
the connecting ports into the socket on the module. Then fit the parts
10
shown with dotted lines on the module into the indentation shown with
dotted lines on the peg-board. (See the above figure)
Step 2
Hold the module, then turn it to the direction as the arrow sign for
about 50 degrees till it can not move forward any longer, make sure the
three installing pegs are in right positions. (See the above figure)
11
Step 3
After the module is in right position, tighten the special screw (the
screw will not drop even when it is loosed to the end) manually or with a
screwdriver. Be sure the screw is tight, otherwise, the module might fall
when the unit is running. Installation of the camera completed. (See the
above figure)
Attention: Once the module is installed well with the housing, please
don’t merely pull the power, video and controlling integrated cable to lift
the unit, with which operation the connecting ports of the integrated
cable may be pulled out, or even worse, the connecting ports may be
damaged permanently. The right operation method is: hold the whole
housing in your palms, then continue with the installing and connecting
work.
12
2-4. Installation of Vitreous Cover
1. Installation of the Vitreous Cover of Nine-inch Dome Camera
Put on the gloves and fit the point signed on the vitreous cover to
the corresponding one on the housing, then turn it to right for about 30
degrees till it can not move ahead any longer. (See the above figure)
13
2. Installation of the Vitreous Cover of Seven-inch Dome Camera
Put on the gloves and fit the vitreous cover to the housing well in
right position, then tighten the two screws manually or with a screwdriver.
(See the above figure)
3. Installation of the Semi-dome Vitreous Covers of Seven-inch and
Nine-inch Dome Camera
Loading...