Poison Spyder STEERING BOX SKID User Manual

STEERING BOX SKID INSTALLATION
Poison Spyder Customs Steering Box Skid fully protects one of your Jeep’s most vulnerable and vital components: your steering gear box. Installation of the Steering Box Skid should take less than one hour.
frame On the outside of the frame rail, remove the two forward bolts that hold the steering box in place (there are other bolts that hold the steering box in place, so there is no need to support the steering box).
2. Hold the steering box skid in place and thread all three bolts that were removed back into place. Torque these bolts to factory specs.
3. On the Steering Box Skid there is one more hole that is located to the far left (if you are
lookingatthefrontoftheJeep)thatisush
with your OE bumper. Drill a 3/8” (YJ) or 1/2” (TJ & LJ) hole through the OE bumper using the hole in the skid plate as a template.
Use the provided hardware to nish the
installation.
PARTS LIST (YJ)
(1) Steering Box Skid
(4) 3/8atwasher
(2) 3/8-16 nylon insert lock nut
PARTS LIST (TJ & LJ)
(1) Steering Box Skid
(2) 1/2atwasher
(1) 1/2-13 nylon insert lock nut
TOOLS NEEDED
• T55 Torx wrench or socket with ratchet
• Drill motor
• 3/8” (YJ) or 1/2” (TJ or LJ) drill bit
• 7/32” (YJ) or 5/16” (TJ or LJ) hex key (Allen
wrench) or socket with ratchet
• 9/16” (YJ) or 3/4” (TJ or LJ) end wrench or socket with ratchet
INSTALLATION PROCEDURE
1. Remove the lower torx bolt that holds the bumper in place on the driver’s side of the
WARRANTY
Poison Spyder Customs™ warranties all of the products we sell and distribute for one (1) year from the date of sale. These products will be free from defects in material and workmanship under normal installation, and use. Due to the
intended use the powder coat nish is warranted for ninety (90) days. The nish warranty will not
cover a product if it has been damaged in any way. Warranty is limited to repair or replacement. Poison Spyder Customs™ does not offer any type of labor or shipping allowance and all warranty claims are subject to inspection by Poison Spyder Customs™.
At the discretion of Poison Spyder Customs™, the products in question can be repaired or replaced when found defective. Prior to any replacement or repair, written authorization must be obtained from Poison Spyder Customs™. Failure to contact us prior to having warranty work preformed will immediately void all applicable warranties; and it is then the sole responsibility of the customer to remit any payment incurred.
The warranty expressed above is the sole warranty of Poison Spyder Customs™, and any other expressed or implied warranties are
hereby specically excluded and disclaimed.
©2009 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM
INSTALLATION INSTRUCTIONS
Poison Spyder Customs • STEERING BOX SKID INSTALLATION Page 2
HOLD HARMLESS AGREEMENT
1. In purchasing a Poison Spyder Customs Product™ I release, waive, discharge and covenant not to sue Poison Spyder Customs
ofcers, servants, agents, or employees
(hereinafter referred to as Releasees) from any and all liability, claims, demands, actions and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by me (or anyone else), any property belonging to me (or anyone else), whether caused by the negligence of the releasees or otherwise, while working on, using or any activity related to this product.
2. I am fully aware of risks and hazards connected with the use of a this product and I elect to voluntarily engage in such use of this product knowing that the use may be hazardous to me and my property. I voluntarily assume full responsibility for any risks of loss, property damage or personal injury, including death, that may be sustained by me (or anyone else), or any loss or damage to property owned by me (or anyone else), as a result of using this product, whether caused by the negligence of releasees or otherwise.
3. I further agree to indemnify and hold harmless the releasees from any loss, liability, damage or costs, including court cost and attorney fees, that they may incur due to my use of a this product, whether caused by negligence of releasees or otherwise.
4. It is my express intent that this Release and Hold Harmless Agreement shall bind the members of my family and spouse, if I am alive, and my heirs assigns and personal representative, if I am deceased, and shall be deemed as a release, waiver, discharge, and covenant not to sue the above named releasees. I further agree that this Waiver of Liability and Hold Harmless Agreement shall be construed in accordance with the laws of the State of California.
By accepting this product, I acknowledge and represent that I have read the above Waiver and Liability and Hold Harmless Agreement, understand it and accept it voluntarily as my own free act and deed; no oral presentations, statements, or inducements, apart from the
foregoing written agreement, have been made; I am at least eighteen (18) years of age and fully competent; and I execute this Release for full, adequate and complete consideration fully intending to be bound by same.
If you do not agree with the preceding Hold Harmless Agreement, you may return the product and receive a full refund. Please, contact a Poison Spyder Customs™ sales representative and they will issue a call tag for the product in question. Once the product has been received by Poison Spyder Customs™ a full refund will be issued.
©2009 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM
INSTALLATION INSTRUCTIONS
Loading...