Poison Spyder LED MARKER LAMP User Manual

3/4” LED MARKER LAMP INSTALL NOTES

2-Wire 3/4” LED Lamp

This high quality DOT-approved LED lamp
is designed to provide years of trouble-free
performance.

PARTS LIST

Please check your packages immediately upon
arrival to ensure that everything listed is included,
and to check for damage during shipping. If
anything is missing or damaged, call Poison
Spyder at [phone] as soon as possible.

(1) 3/4” LED Marker Lamp with Pigtail

(1) Rubber Grommet

INSTALLATION NOTES

1. This item is not a direct “plug and play” item.
Installation requires a basic understanding
and skillset of automotive wiring. The installer
may need to use a test light or multimeter
to identify the correct wires in the vehicle’s
wiring harness to tap into in order to power
this lamp. If this is beyond your skills, please
seek the help of someone more experienced
with automotive wiring.

2. On the 2-Wire version, there are two wires
on the lamp pigtail. The BLACK wire is
POSITIVE. The WHITE wire is NEGATIVE.
Be sure to make your connections
appropriately. The 2-wire LED may be used
as either a marker lamp (running light) or as
a turn signal, but not as both simultaneously.

3. On the 3-Wire version, there are three
wires on the lamp pigtail. The BLACK wire is
POSITIVE for the marker lamp function. The
RED wire is POSITIVE for the turn signal

3-Wire 3/4” LED Lamp

function. The WHITE wire is NEGATIVE, or
ground. Be sure to make your connections
appropriately. The 3-wire LED may be used
as both a marker lamp and a turn signal
simultaneously.

4. We recommend using female bullet

connectors (not included) to connect to the
male bullet connectors already existing on
the pigtail (2-wire version only). Alternatively
you may cut the existing bullet connectors
off of the pigtail to use the connector type
of your choice. The 3-wire version does not
come with pre-installed connectors so you
will have to supply and use connectors of
your choice.

5. DO NOT cut off the fat “pill” section of the
pigtail (3-wire version only). The components
housed inside it are necessary for proper
function of the LED lamp.

6. Many Poison Spyder products such as
Crusher Flares™ and DeFenders™ come
with a 3/4” mounting hole already cut into
them, intended for mounting this lamp.

7. If installing into a blank panel or location
without an existing hole, use a 3/4” hole
saw, step drill, or Greenlee punch to create a
suitable hole.

8. Installing the lamp into the 3/4” hole is

easiest by rst slipping the pigtail through the

grommet, then through the hole. Next, push
the grommet into place in the hole, followed
by pushing the lamp into the grommet. A
small amount of soapy water may help
lubricate the components during installation.

©2013 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM

INSTALLATION INSTRUCTIONS

Poison Spyder Customs •

3/4” LED MARKER LAMP INSTALL NOTES Page 2

WARRANTY

Poison Spyder Customs™ warranties all of the
products we sell and distribute for one (1) year
from the date of sale. These products will be
free from defects in material and workmanship
under normal installation, and use. Due to the

intended use the powder coat nish is warranted
for ninety (90) days. The nish warranty will not

cover a product if it has been damaged in any
way. Warranty is limited to repair or replacement.
Poison Spyder Customs™ does not offer any
type of labor or shipping allowance and all
warranty claims are subject to inspection by
Poison Spyder Customs™.

At the discretion of Poison Spyder Customs™,
the products in question can be repaired or
replaced when found defective. Prior to any
replacement or repair, written authorization must
be obtained from Poison Spyder Customs™.
Failure to contact us prior to having warranty work
preformed will immediately void all applicable
warranties; and it is then the sole responsibility
of the customer to remit any payment incurred.

The warranty expressed above is the sole
warranty of Poison Spyder Customs™, and
any other expressed or implied warranties are

hereby specically excluded and disclaimed.

HOLD HARMLESS AGREEMENT

In purchasing a Poison Spyder Customs
Product™ I release, waive, discharge and
covenant not to sue Poison Spyder Customs

ofcers, servants, agents, or employees

(hereinafter referred to as Releasees) from any
and all liability, claims, demands, actions and
causes of action whatsoever arising out of or
related to any loss, damage, or injury, including
death, that may be sustained by me (or anyone
else), any property belonging to me (or anyone
else), whether caused by the negligence of the
releasees or otherwise, while working on, using
or any activity related to this product.

I am fully aware of risks and hazards connected
with the use of a this product and I elect to
voluntarily engage in such use of this product
knowing that the use may be hazardous to
me and my property. I voluntarily assume full
responsibility for any risks of loss, property
damage or personal injury, including death, that
may be sustained by me (or anyone else), or

any loss or damage to property owned by me (or
anyone else), as a result of using this product,
whether caused by the negligence of releasees
or otherwise.

I further agree to indemnify and hold harmless
the releasees from any loss, liability, damage or
costs, including court cost and attorney fees, that
they may incur due to my use of a this product,
whether caused by negligence of releasees or
otherwise.

It is my express intent that this Release and Hold
Harmless Agreement shall bind the members of
my family and spouse, if I am alive, and my heirs
assigns and personal representative, if I am
deceased, and shall be deemed as a release,
waiver, discharge, and covenant not to sue the
above named releasees. I further agree that this
Waiver of Liability and Hold Harmless Agreement
shall be construed in accordance with the laws
of the State of California.

By accepting this product, I acknowledge and
represent that I have read the above Waiver
and Liability and Hold Harmless Agreement,
understand it and accept it voluntarily as my
own free act and deed; no oral presentations,
statements, or inducements, apart from the
foregoing written agreement, have been made;
I am at least eighteen (18) years of age and
fully competent; and I execute this Release for
full, adequate and complete consideration fully
intending to be bound by same.

If you do not agree with the preceding Hold
Harmless Agreement, you may return the product
and receive a full refund. Please, contact a
Poison Spyder Customs™ sales representative
and they will issue a call tag for the product in
question. Once the product has been received
by Poison Spyder Customs™ a full refund will
be issued.

©2013 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM

INSTALLATION INSTRUCTIONS