Poison Spyder FRONT STINGER User Manual
FRONT STINGER INSTALLATION
The Poison Spyder Customs Front Trail or
Comp Stinger is easy to install with the right
tools and good mechanical abilities. If you are
not condent in your mechanical skills, please
seek the help of a professional to perform the
installation. Please read through these entire
instructions before proceeding with installation.
PARTS LIST
(1) Front Stinger (Trail or Comp)
TOOLS NEEDED
• Torx T55 Socket
• Ratchet
• Torque Wrench
BEFORE YOU BEGIN
The Poison Spyder Customs Front Stinger comes
as un-painted, bare steel. You will want to either
powder coat or paint the bumper prior to install. If
painting yourself, careful preparation will make a
big difference in the quality and longevity of your
paint job, even using “rattle can” aerosol paints.
Begin by thoroughly cleaning the Stinger with
solvent or degreaser, then make sure all residue
is removed. Even if you use cheap paint, try to
use a good quality primer. “Etching” primers are
best to use on bare, un-painted metal. Allow it to
properly dry before paitning, and between paint
coats.
INSTALLATION PROCEDURE
1. Park the Jeep on a at, level surfaceand
set the parking brake.
2. Remove existing front bumper. If it is still
the OEM bumper and hardware, there are
four bolts (two on the top and two on the
bottom that hold the bumper in place). These
will likely be Torx bolts, use a T55 torx bit.
3. Using the same hardware, install the
Stinger Bumper in place of the bumper that
wasremoved.TorquetoOEspecications.
WARRANTY
Poison Spyder Customs™ warranties all of the
products we sell and distribute for one (1) year
from the date of sale. These products will be
free from defects in material and workmanship
under normal installation, and use. Due to the
intended use the powder coat nish is warranted
for ninety (90) days. The nish warranty will not
cover a product if it has been damaged in any
way. Warranty is limited to repair or replacement.
Poison Spyder Customs™ does not offer any
type of labor or shipping allowance and all
warranty claims are subject to inspection by
Poison Spyder Customs™.
At the discretion of Poison Spyder Customs™,
the products in question can be repaired or
replaced when found defective. Prior to any
replacement or repair, written authorization must
be obtained from Poison Spyder Customs™.
Failure to contact us prior to having warranty work
preformed will immediately void all applicable
warranties; and it is then the sole responsibility
of the customer to remit any payment incurred.
The warranty expressed above is the sole
warranty of Poison Spyder Customs™, and
any other expressed or implied warranties are
hereby specically excluded and disclaimed.
HOLD HARMLESS AGREEMENT
1. In purchasing a Poison Spyder Customs
Product™ I release, waive, discharge and
covenant not to sue Poison Spyder Customs
ofcers, servants, agents, or employees
(hereinafter referred to as Releasees) from
any and all liability, claims, demands, actions
and causes of action whatsoever arising out
of or related to any loss, damage, or injury,
including death, that may be sustained by
me (or anyone else), any property belonging
to me (or anyone else), whether caused by
the negligence of the releasees or otherwise,
while working on, using or any activity related
to this product.
2. I am fully aware of risks and hazards connected
with the use of a this product and I elect to
©2009 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM
INSTALLATION INSTRUCTIONS
Poison Spyder Customs • FRONT STINGER INSTALLATION Page 2
voluntarily engage in such use of this product
knowing that the use may be hazardous to
me and my property. I voluntarily assume full
responsibility for any risks of loss, property
damage or personal injury, including death,
that may be sustained by me (or anyone
else), or any loss or damage to property
owned by me (or anyone else), as a result
of using this product, whether caused by the
negligence of releasees or otherwise.
3. I further agree to indemnify and hold harmless
the releasees from any loss, liability, damage
or costs, including court cost and attorney
fees, that they may incur due to my use of a
this product, whether caused by negligence
of releasees or otherwise.
4. It is my express intent that this Release and
Hold Harmless Agreement shall bind the
members of my family and spouse, if I am
alive, and my heirs assigns and personal
representative, if I am deceased, and shall
be deemed as a release, waiver, discharge,
and covenant not to sue the above named
releasees. I further agree that this Waiver of
Liability and Hold Harmless Agreement shall
be construed in accordance with the laws of
the State of California.
By accepting this product, I acknowledge and
represent that I have read the above Waiver
and Liability and Hold Harmless Agreement,
understand it and accept it voluntarily as my
own free act and deed; no oral presentations,
statements, or inducements, apart from the
foregoing written agreement, have been made;
I am at least eighteen (18) years of age and
fully competent; and I execute this Release for
full, adequate and complete consideration fully
intending to be bound by same.
If you do not agree with the preceding Hold
Harmless Agreement, you may return the product
and receive a full refund. Please, contact a
Poison Spyder Customs™ sales representative
and they will issue a call tag for the product in
question. Once the product has been received
by Poison Spyder Customs™ a full refund will
be issued.
©2009 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM
INSTALLATION INSTRUCTIONS
Loading...