USER MANUAL
POINT POD PTY LTD
ACN: 617440258
Patent Pending
Table of Contents
Product Overview ................................................ 4
What’s in the box? / Warranty ...................................... 5
Welcome ........................................................ 6
Safety Instructions ................................................ 7
Technical Specications ........................................... 8
Installation ....................................................... 9
FAQs ............................................................ 11
Repairs and after sales service..................................... 12
4
Product Overview
Multi V1 Compact V1
5
What’s in the box?
Warranty
Point Pods are supplied with everything you need to achieve your superior
power solution.
Your Point Pod installation pack includes:
• Main Point Pod unit complete with upper cup attached
• Outer collet for hole in bench
• Under bench mounting ange
• Fastening clip
• 2.2m 10a power cord
• Installation guide and warranty
Our product is guaranteed to be free from defects in product quality and
components for a period of 24 months from the date of purchase. Proof of
purchase will be required upon warranty claim. Any faults that occur within the
24-month period after purchase under standard use and care will be repaired
or replaced at the discretion of Point Pod Pty Ltd. This warranty is being
offered in addition to the protection the consumer has under the Competition
and Consumer Act 2010, as well as state and territory laws. All of our products
come with a warranty that cannot be excluded under the Australian Consumer
Law. Our customers are entitled to refund or replacement for a major failure
and for compensation for any other foreseeable loss or damage. We will also
repair or replace any goods deemed to be unacceptable due to quality but
does not amount to major failure.
All warranty claims must be submitted to claims@pointpod.com.
6
Welcome
Thanks for purchasing a Point Pod product. You have now joined the
growing number of people who have not compromised their design for
practicality. You have chosen a product that we are very proud of and
we hope you enjoy it as much as we do. You have chosen peace of mind,
as all our products are manufactured to the highest quality and undergo
strict performance and quality testing. As a sign of our condence in
Point Pod’s performance, we have backed it with a 2-year warranty. Most
importantly though, you have chosen the best of architectural design for
your space and we are so glad to share it with you.
7
Safety Instructions
It is important to read this manual and follow all instructions carefully when using our
Point Pod products. Keep the manual, warranty card and receipt of purchase on le
for future reference.
• Point Pod units are to be installed by qualied professional only. Point Pods
are NOT a DIY install. Warranty will be null and void if the unit has not been
professionally installed.
• For indoor use only.
• Point Pod products must be installed to meet all local electrical laws including
distance from water.
• Point Pod products can never be installed horizontally with the sockets facing up.
Sockets must be on a vertical plain at all times.
• Point Pod products are never to be opened by anyone other than a service
technician. Outside of these guidelines will void the warranty.
• Point Pod products are not to be used as a toy or for the amusement of children.
Supervision is recommended.
• Always exercise a high degree of caution when using any electrical devices.
• Avoid spills where possible and never spray water directly into an open unit.
• Do not use if any components of the unit are broken or faulty.
• Never insert anything but the appropriate plug into the sockets.
8
Technical Specications
Point Pod Multi V1
Point Pod Compact V1
Colour: Clear anodized aluminium
Material: Polymide and ABS
Hole size: 100mm
Inner disc size: 92mm
Required space: 550mm depth 100mm diameter
Package size: 750x185x125mm
Weight: 3.2kgs
Cable length: 1.9m
Socket conguration: 3x power outlets, 2x2.1a USB
Supply Voltage: 240V ac 50Hz
Max Current: 10a 0r 2400w
Overload switch
Ingress rating: IP44
Approval no. GMA-504353-EA
Designed and engineered in Australia
Made in China
Patent Pending
Colour: Clear anodized aluminium
Material: Polymide and ABS
Hole size: 100mm
Inner disc size: 92mm
Required space: 450mm depth 100mm diameter
Package size: 650x185x125mm
Weight: 3.1kgs
Cable length: 1.9m
Socket conguration: 2x power outlets
Supply Voltage: 240V ac 50Hz
Max Current: 10a 0r 2400w
Overload switch
Ingress rating: IP44
Approval no. GMA-504353-EA
Designed and engineered in Australia
Made in China
Patent Pending
9
Installation
Point Pod products should only be installed by a qualied professional.
Timber or Laminate Installation
For new installs we recommend steps 1-5 be done in the workshop of the bench top supplier.
Step 1. Remove the Point Pod from the box and check everything is present and
accounted for.
Step 2. Carefully mark out where the unit is to be installed, taking into account the void the
unit needs under the bench top.
Step 3. Drill 100mm OD hole in the bench top material using a t for use 100mm holesaw
without the pilot bit. This is achieved by using a pre-prepared 100mm template. Dimensions
needed are 100mm for the outer hole and 92mm for the inner disc. The inner disc will most
likely need sanding down with a belt sander or similar sander to achieve the measurements
needed. Have the cup close by for continual testing as this process is being completed.
Step 4. Silicone or glue the outer collet into the hole making sure it sits ush with the top of
the bench surface.
Step 5. Once the silicone or glue has cured, screw the mounting ange to the underside of
the timber positioned around the outer collet.
Step 6. Once the mounting ange has been screwed securely in place, install the Point
Pod unit from the top and lower it down until it is sitting ush with the outer collet and has
an even margin around. Fix the unit in place by placing the fastening clip supplied to the
mounting ange and tightening appropriately.
Step 7. Set height adjuster screws in the receiving cup to the right height for your disc insert.
Glue the disc in place with silicone or preferred adhesive making sure to line up all features
of the timber.
Step 8. After insert has set, plug the unit in ready for testing. The unit has a 30 second delay
and then when activated will travel in the downwards motion rst. Activate the unit again
by pressing on the top and the unit should rise up to the open position. Activate again and
it will lower back down. In this closed position double check the height and margins and
adjust where necessary.
The unit is now ready for everyday use.
10
Installation
Point Pod products should only be installed by a qualied professional.
Stone Installation
Step 1. Remove the Point Pod from the box and check everything is present and accounted for.
Step 2. Carefully mark out where the unit is to be installed, taking into account the void the
unit needs under the bench top.
Step 3. Drill 100mm OD hole in the stone bench top using a t for use 100mm holesaw.
Alternatively, cut the holes with a water jet. Dimensions needed are 100mm for the outer hole
and 92mm for the inner disc.
Step 4. Silicone or glue the outer collet into the hole making sure it sits ush with the top of the
bench surface.
Step 5. Once the silicone or glue has cured, adhere the mounting ange to the underside of the
stone positioned around the outer collet. This should be adhered using Megapoxy or similar
product.
Step 6. Once the mounting ange is set in place and Megapoxy or similar product has set,
install the Point Pod unit from the top and lower it down until it is sitting ush with the outer
collet and has an even margin around. Fix the unit in place by placing the fastening clip
supplied to the mounting ange and tightening appropriately.
Step 7. Set height adjuster screws in the receiving cup to the right height for your disc insert.
Glue the disc in place with silicone or preferred adhesive making sure to line up all features of
the stone.
Step 8. After the stone top has dried, plug the unit in ready for testing. The unit has a 30
second delay when rst plugged and then when activated will travel in the downwards motion
rst. Activate the unit again by pressing on the top and the unit should rise up to the open
position. Activate again and it will lower back down. In this closed position double check the
height and margins and adjust where necessary.
The unit is now ready for everyday use.
Follow the QR code link for installation video
11
FAQs
Q. Is the product waterproof?
A. The Point Pod is designed and tested to meet Aus/NZ standards with an IP rating of 44.
Any water spilled will be diverted away from the Point Pod and drip into the cabinet below
for ease of clean up.
Q. Can I use 15 amp power with a Point Pod?
A. No, the maximum current to be used is 10a, which covers most household items.
Q. Is the Point Pod surge protected?
A. The units are not surge protected.
Q. Do Point Pods have overload protection?
A. Yes, the Point Pods are tted standard with overload protection, which will be tripped in
the event of the unit drawing too much current.
Q. What happens if something gets caught between the Point Pod and the bench whist
traveling to a closed position?
A. The Point Pod has been programmed to detect resistance and immediately switches
directions to rise back up again.
Q. What happens if pressure is applied to the top whilst the Point Pod is traveling up?
A. The unit will sense this and stop.
Q. When I rst plug my Point Pod in for use it doesn’t activate on rst touch. What do I do?
A. The Point Pod has been programmed to travel down rst. You will need to activate it
again to begin traveling up.
Q. My Point Pod doesn’t activate when I push down on it. What do I do?
A. The Point Pod products are designed to be activated upon release. Firmly press down,
and on release, you will see the unit activated.
12
Repairs and
After Sales Service
Unfortunately there are times when a component in one of our units is faulty and needs
repair. Point Pod recognises this and wants to provide the best service possible to our
customers. Never attempt to repair a Point Pod product yourself. Point Pod has trained
technicians who will identify the problem and repair the product or replace it if needed. If
the supply cord is damaged, it shall be replaced by the manufacturer or its service agent or
similar qualied person.
In the event of a warranty claim, you can contact Point Pod Pty Ltd directly:
Warranty Department
PO Box 1437
Kenmore, QLD, 4069
Ph: +61 7 3040 8280
Email: claims@pointpod.com
At its discretion, Point Pod Pty Ltd may replace goods with refurbished units or
components of the same type.
Phone: +61 7 3040 8280
Email: info@pointpod.com
Web: www.pointpod.com
ABN 36617440258
Loading...