PMR PMRMAF2C2-X-RET User Manual

Part Number: PMRMAF2C2-X-RET
INTRODUCTION
The PMR Music Angel is a Bluetooth Headset accessory that lets
you listen in stereo to your portable radio or MP3 player and yet you
can handle incoming mobile phone calls without removing your
earphones or headset. Music Angel has a built-in microphone that
you can speak into during phone calls. Simply connect the Music Angel into your MP3 player or iPod and
connect your headphones into the Music Angel. Listen as normal
and take or make mobile calls without removing or changing your
headphones. Music Angel Universal is ideal for busy music and
radio lovers.
GETTING TO KNOW YOUR MUSIC ANGEL
Please note some models will differ slightly in style and functionality
which may vary according to their specifications.
Charging Music Angel
Before using your Music Angel, you must charge it for
approximately two hours. Once fully charged, the battery provides
up to 4 hours of talk time and up to 120 hours of standby time.
To charge the Music Angel
1. Plug the USB charging cable into the Mini USB socket.
2. Plug the other side of the USB charging cable into a
powered USB socket on a PC or laptop computer. During
charging, the amber LED will be on.
3. When charging is finished, the amber LED will turn off.
4. Unplug the USB charging cable.
Switching Music Angel On and Off
To turn on Music Angel
Press and hold the ON/OFF
button for four seconds. The
Blue LED will flash 3 times and you will hear the ascending ON
tone. Music Angel turns on and is ready to make and receive calls.
To turn off Music Angel
When Music Angel is on, press and hold the
ON/OFF
button for four seconds. The Blue LED will flash 3 times and you
will hear the descending OFF tone. Music Angel turns off and
no LEDs are on or flashing.
Pairing Music Angel and your Mobile Phone
Before you can use Music Angel with your Bluetooth-enabled
mobile phone you must pair Music Angel with the phone. Pairing
is the process of linking Music Angel with your phone. After
pairing is complete, you can use Music Angel only with the
paired mobile phone. If you wish to use Music Angel with a
different mobile phone, you must redo the pairing process with
the new mobile phone. In this case, Music Angel will no longer
work with the previous mobile phone unless you pair them again.
Before you commence pairing ensure that the battery is
fully charged. To pair Music Angel and your mobile phone
1. Turn on the mobile phone and place it within 3 metres of
Music Angel.
2. Turn on Music Angel by pressing and holding the ON/OFF
button for about 6 seconds until the blue and amber LEDs
flash alternately. Music Angel is now turned on and in pairing
mode.
3. Initiate the discovery feature on the mobile phone. (Refer to
the mobile phone user guide for this feature.)
4. The Music Angel’s Bluetooth name is “BTHS-Music”
5. Enter the default pin code “0000”, when the mobile phone
requests a PIN / password (sometimes known as passkey).
6. When Music Angel is paired with your mobile phone, the
Music Angel blue LED will now flash medium/slow at
three-second intervals. Music Angel is now in standby mode,
ready to make and receive calls.
To cancel pairing mode
While in pairing mode, you can cancel the pairing process and turn off
the Bluetooth function on Music Angel. Press and hold the ON/OFF
button for three seconds. Both LEDs will turn off and you will hear the
descending OFF tone. Making calls (Not all Bluetooth phones support these features)
You can make outgoing calls from your mobile phone itself or directly
from the Music Angel control buttons using voice dialling and last
number redial. To speak to your caller use Music Angel’s built-in
microphone.
To make calls from your mobile phone
Dial the call from your mobile phone keypad. The call is
automatically connected to your Music Angel.
To make calls using voice dialling (if supported by your
phone)
1. Click the
Answer button on your Music Angel
2. Speak the name of the person you wish to call. The call is
automatically connected to your mobile phone.
MUSIC ANGEL
UNIVERSAL
USER GUIDE
Declaration of Conformity.
We declare that product PBTMAF2C2-X conforms to
the R&TTE Directive 1999/5/EC.
FCC ID:QQFPBTMAYZC2-X
CE No: 0678
To make calls using last number redial (if supported by your
mobile phone)
From standby mode, press and hold the Answer button for about 3
seconds. The call is automatically connected to your phone.
Some phones support a specific ‘Redial’ voice command so it is
possible to redial using voice dialling as well.
Receiving calls
You must configure your mobile phone to answer calls directly on
Hands-Free/Bluetooth headset. Refer to the mobile phone user guide
for instructions on initiating this feature.
Answering a call
When you hear an incoming call ring in the headset, click the
Answer button on Music Angel. The call is connected to your
headset. Reject calls
When you hear an incoming call ring in the headset, click the
Hang-up/ON/OFF button. The call will be rejected. Ending calls
When you have finished your call, press the
Hang-up/ON/OFF button. The call will be disconnected.
Transfer calls
You can transfer the calls connected to your headset back to your
mobile phone, or from your mobile phone to your headset.
To transfer calls from your headset to phone (phone
dependent)
Click the Music Angel Answer button. You hear a short beep in
your headphones. Audio is now connected through your mobile
phone’s speaker and microphone. To transfer calls from your phone to headset
With the call connected to your mobile phone, click the Answer
button on Music Angel. The call is now connected to your headset
and to the microphone on Music Angel
Adjust the call volume
To increase the volume
During a call, click the Volume Up button + to increase volume by 1
step. Repeat this procedure until you have reached the desired
level. To decrease the volume
During a call click the Volume Down button - to decrease volume
by 1 step. Repeat this procedure until you have reached the
desired level.
Muting the headset
You can mute and un-mute the Music Angel microphone temporarily
so that you cannot be heard by the other caller.
To mute and un-mute the headset
During a call click the
Mute button.
To un-mute the headset, click the Mute button again.
Call waiting (not all phones may support this feature)
When a second call comes in, click the
Call Waiting button. The
first call is put on hold and the second call is connected through to the
headset. Just click the Call Waiting button to switch between calls.
Conference call (not all phones may support this feature)
With two active calls, press and hold the Call Waiting button for
approx 3 seconds. Both calls will be switched through to the headset. Visual and audible indications Visual indications
Two LEDs (blue and amber) indicate the status of the headset:
Status Indication
Battery is full
While charge cable is connected
amber LED is OFF
Battery is low Amber LED flashes
Headset is off Both LEDs are OFF
Headset is in standby
mode, ready to make and
receive calls
Blue LED flashes at three -second
intervals
Headset is in pairing mode
Blue and amber LEDs flash
alternately.
Audible Indicators
Tones heard through the headset provide an audible indication of a
requested action:
Tone name Sound Indicates
ON Ascending (3 notes)
Headset has been
turned on
OFF Descending (3 notes)
Headset is about to
turn off
PAIRING Low/High (2 notes)
Headset is in pairing
mode.
RINGING Double 4 note cadence Incoming call
REJECT CALL
Low/High (2 notes,
repeated)
Call has been rejected
CALL WAITING
Beep (1 note,
repeated)
2
nd
call incoming
LOW BATT
Beep (1 note, repeated
32 secs)
Battery needs charged
MUTED
Beep (1 note, repeated
4 secs)
Microphone is muted
TRANSFER Beep
Transfer from headset
to phone
DISCLAIMER
Whilst every effort has been made to ensure that the information in this
manual is accurate and complete, no liability will be accepted for any
errors and/or omissions made. The manufacturer reserves the right to
make changes and improvements to the specifications and features of
the hardware and firmware of the products described in this document
without prior notice. Reproduction, transfer, distribution or storage of
part or all of the contents in this document in any form is prohibited
without prior permission of the manufacturer. All trademarks
acknowledged.
TROUBLESHOOTING
PROBLEM CAUSE ANALYSIS SOLUTION
Headset will not go
into pairing mode
Headset must be
switched off completely
before it will go into
pairing mode
Switch off headset and
then try to put it in paring
mode again.
Phone cannot find
headset
Headset is not in pairing
mode or is too far away
from phone
Ensure headset is within
one or two metres of the
phone and that it is in
pairing mode.
Pairing fails PIN error or PIN entry
error
1. Make sure you enter
the correct PIN code /
Passkey. For the
headset it is 0000.
2. Don’t take too long to
enter the PIN code
Bluetooth link is not
established
automatically on
incoming or
outgoing calls
Pairing information in
phone or headset has
been cleared.
Try pairing again
No voice is heard
from the headset
when a call is
established
Manual switching of
voice is needed for
some phones.
Use phone menu to
transfer voice to the
headset.
No voice from
phone and headset
Bluetooth function of
phone is not working
Use phone menu to
transfer voice to the
speakerphone
Noise / crackling
can be heard
during a call
Your phone signal is
poor.
The headset is too far
away from the phone or
there is a metal
obstruction.
1. Make sure your
phone connection is
OK
2. Don’t take too long to
enter the PIN code
Make sure the
headset and phone
are not too far away
from each other and
that neither is
shielded by any metal
objects or even your
body.
3. A nearby device is
interfering with the
call. Move away from
it.
1. Voice dialling
does not work
2. You cannot
transfer calls
from headset
to your phone
3. Last number
redial does not
work
4. Call waiting
does not work
5. Call reject
does not work
Your mobile phone may
not support this feature
1. Make sure your phone
supports the feature
in general and over
Bluetooth
2. If in doubt delete your
headset from the list
of Bluetooth devices
in your phone and try
pairing them again.
Customer Support: In addition to the troubleshooting table on the
this page you can get support on the PMR support forum at this web
address http://www.esktech.com/forums/ For other PMR Bluetooth products or support, please contact PMR
Technology Ltd
Web: www.pmrtechnology.co.uk
Email: support@pmrtechnology.co.uk
Version: QSGMAUNIV-Ve
r
15
Loading...