GETTING STARTED
Remove all components from the package. Items in the pack
include: – PMR Bluetooth headset with Ear Hook, Ear Cap, User
Guide, Lanyard (optional) & Mains Adapter. Please check the
contents carefully and contact your local dealer immediately if
there are any shortages.
GETTING
TO KNOW YOUR HEADSET
Please note some models of headset will differ slightly in style and
the functionality may vary on certain models according to their
specifications.
Talk Button
Amber LED
Volume Up
Volume Down
CHARGING YOUR
HEADSET
Before using the headset, you must charge the headset for
approximately two hours. When fully charged, the battery
provides up to 5 hours of talk time and up to 100 hours of standby
time.
Please note talk time is also a function of the mobile phone
and factory determined settings of the phone so you may
find this figure is reduced under certain conditions.
To charge the headset
1. Plug the AC adapter into the headset.
2. Plug the AC adapter into a wall outlet. When the headset is
charging, the amber LED will light up.
3. Unplug the charger cable from the wall outlet and the
headset when charging has finished, the amber LED will
turn off or be dim.
Battery Indication: The amber LED can turn off after 2/3 hours
charging. This will indicate that the Headset can be used,
however it is recommended that the user charges for a full 2
hours in order to fully charge the battery for normal operation.
PAIRING THE
HEADSET TO YOUR MOBILE PHONE
Pairing is the process of linking the headset
with your Bluetooth
mobile phone. Before you use the PMR headset with your mobile
phone you must pair the devices. After this process is completed,
you can use the headset only with its paired mobile phone. If you
wish to use the headset with a different mobile phone, you must
repeat the pairing process with the new mobile phone. In this
case, the headset will no longer work with the original mobile
phone. Please refer to the user manual of your mobile phone for
further information on ‘How to Pair’.
Before you pair the headset, ensure that the battery is fully
charged and that your mobile is switched on and it is in
discoverable mode..
To pair the devices
1. With the headset turned off, press and hold the TALK
button for five seconds. The blue and amber LEDs will
flash alternately, and you will hear the PAIRING tone.
2. Release the TALK button. The headset is now in Pairing
Mode.
3. Turn on the mobile phone and place it within 10 feet of
the headset.
4. Initiate the device discovery feature on the mobile phone.
Refer to the mobile phone user guide for instructions for
initiating this feature.
5. When prompted by the mobile phone, enter the headset
pin code 0000. When pairing is complete, the blue LED
on the headset will flash at one-second intervals and the
headset will be placed in standby mode, ready to make
and receive calls. Please note if battery is low then
amber light not blue light will flash.
If disconnection or lost link occurs, it maybe due to the
following reasons:
a) The range is over 10 feet between both headset and
the mobile phone.
b) Mobile phone disconnected the link to conserve
power or enable other function.
c) Either device has been switched off.
Note: The headset, in normal operation, should maintain the
connection with the mobile phone at all times once the pairing
mode and connection has been established between the two
devices.
To cancel pairing mode - While you are in pairing mode, you
can cancel the pairing process and turn off the headset.
Press and hold the TALK button for three seconds. Both
LEDs will turn off and you will hear the OFF tone.
FITTING THE
HEADSET ON YOUR EAR
The PMR Headset is designed to fit comfortably in your
ear. The ear hook can be rotated on its axis allowing you
to position on right or left ear. Please note the ear hook is
designed such that it can fit over the ear or under the ear
as well as right and left ear.
To place the headset on your ear - Place the headset
speaker in your ear with the microphone angled towards
your mouth. The headset should fit snugly in your ear.
However, if the speaker is too small for your ear, you can
change to other size of the ear cap that is provided with
your headset.
To add the ear cap - Stretch the ear cap around the end
LED
PMR
BLUETOOTH HEADSET
P/N PBTFABH2C2-P,R,J,G
USER GUIDE
Blue LED
Declaration of Conformity. We declare that product
PBTFABF2C2-P conforms to the R&TTE Directive
1999/5/RC .
of the speaker.
To add the Optional Lanyard - simply connect via the small
hole at the base of the ear hook.
WARNING – It is possible to remove the ear hook and
replace but for normal operation and fitment this is NOT
necessary. Simply rotating the ear hook on its axis will
allow easy fitment to the ear.
POWERING YOUR
HEADSET
To turn on the headset - Press and hold the Talk button for
four seconds. You will hear the ON tone. The headset turns on
and is placed in standby mode, ready to make and receive
calls.
To turn off the headset -
When the headset is on, press and
hold the Talk button for four seconds. You will hear the OFF
tone. The headset turns off.
MAKING CALLS
You can make calls from your mobile phone, or directly from
the headset using voice dialing commands (if this feature is
supported by your mobile phone).
To make calls from your mobile phone - Dial the call from
your mobile phone. Dependent on your mobile phone settings
the call is automatically connected to your headset.
To make calls using voice dialing (if supported by your
mobile phone) - Press the Talk button on your headset.
Speak the name of the person you wish to call. The call is
automatically connected to your headset.
RECEIVING CALLS
You must configure your mobile phone to answer calls directly
on your Bluetooth headset. Refer to the mobile phone user
guide for instructions for initiating this feature.
When your mobile phone rings, press the Talk button on your
headset. The call is automatically connected to your headset.
Please note you can also Reject calls by depressing the talk
button for about 3 seconds. (Not all phones support this
feature)
ENDING CALLS
When you have finished your call, press the Talk button on
your headset. The call will be disconnected.
TRANSFERRING CALLS
You can transfer calls connected to your headset back to your
mobile phone, or from your mobile phone to your headset.
(Not all phones support this feature)
To transfer calls from your headset to the phone or from the
phone to the Headset press the talk button for about 3
seconds until you hear the tone.
ADJUSTING THE VOLUME
To increase the volume - Press (click) the top of the Volume
button + to increase volume by 1 step, repeat this procedure
until you have reached the desired level.
To decrease the volume - Press (click) the bottom of the
Volume button – to decrease the volume by one step, repeat
this procedure until you have reached the desired level.
MUTING THE
HEADSET
You can mute and un-mute the microphone temporarily so
that you cannot be heard by the connected party.
To mute the headset - Press and hold the
Volume up button
for three seconds.
To un-mute the headset - When the microphone is muted,
press and hold either Volume button for three seconds.
VOICE
DIAL
Press the talk button when Headset is not on a call, a voice
prompt will be heard. This is also a phone dependent feature.
LAST NUMBER REDIAL
Certain models only may have this feature. Depress either
volume button when headset is not on call for about 3 second
interval and this will enable the phone to provide last number
redial or alternatively press both volume up and down
together.
VISUAL INDICATORS
Visual Indicators - Two LEDs (blue and amber) indicate the
status of the headset:
Status Indication
Battery 2/3 full Amber LED is off or dim
Battery low
Amber LED on instead of
Blue LED
Headset off Both LEDs are off
Headset in standby
mode, ready to make &
receive calls
Blue LED flashes at 1
second intervals
Headset in pairing mode
Blue and amber LEDs flash
alternately.
Headset making
connection audio
connection for voice dial
Blue LED twice quickly at 1
second intervals
Headset in talk mode
Blue LED flashes four
times quickly at one
second intervals
TROUBLESHOOTING
Please note that you should also be familiar with the operation
of your mobile phone and how to connect to Bluetooth devices.
Please read your mobile phone user guide carefully. Please
note that the Bluetooth headset will only work with Bluetooth
mobile phones. For operation with a PC or laptop device
please note that these devices should also be Bluetooth
enabled with appropriate third party software in order to
enable correct operation.
Symptom/Problem
Solution
When Talk button is
pressed, no LED
indicator
• Unit not charged
• Consult authorized dealer
Headset powers on
with blue LED flashing
but no connection to
mobile phone
• Check unit is paired to
phone. Check settings in
phone. Headset default
name is BTHS
• Check phone is switched
on
• Check handsfree settings
for phone
• Ensure headset & phone
are within range
Headset does not
charge
• Check mains charger
adapter is connected to
the headset securely & is
switched on
• Check mains charger is
working using another
device
• Consult authorized dealer
CUSTOMER SERVICE INFORMATION
For other PMR Bluetooth products or support , please view
our website – www.pmrtechnology.co.uk
or email
support@pmrtechnology.co.uk or contact your local
representative.
DISCLAIMER
Whilst every effort has been made to ensure that the
information in this manual is accurate and complete, no
liability will be accepted for any errors and/or omissions made.
The manufacturer reserves the right to make changes and
improvements to the specifications and features of the
hardware and firmware of the products described in this
document without prior notice. Reproduction, transfer,
distribution or storage of part or all of the contents in this
document in any form is prohibited without prior permission of
the manufacturer. All trademarks acknowledged.
Loading...