Plus Piano HE-3200, HE-3200 User Manual

Download

Page 1

User’s Manual

HE-3200

English

Page 2

E – 2

Installation

* Allow at least 10 cm (3.9 inch) of space between the projector top

panel and its surroundings. Also allow at least 10 cm (3.9 inch) of other spaces around the projector.

* The projector should be placed on a flat, level surface and in a dry

area free from dust and moisture.

* The projector should always be handled with care. Dropping or jar-

ring the projector could damage internal components.

* If you wish to have the projector installed on the ceiling do not attempt

to install the projector yourself. The projector must be installed in accordance with any local building codes by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury.

* Do not place this product near water, near a bathtub, in a wet base-

ment or near a swimming pool and the like.

Power supply

The projector is designed to operate on a power supply of 100-240V AC, 50/60Hz. Ensure that your power supply fits this requirement before attempting to use your projector.

* Handle the power cable carefully and avoid excessive bending. A

damaged cord can cause electric shock or fire.

* If the projector is not be used for an extended period of time, discon-

nect the plug from the power outlet. Do not unplug the power cable from the wall outlet under the following circumstances, doing so may cause damage to the projector:

Cleaning

* Unplug the projector before cleaning. * Use a blower or lens paper to clean the lens, and be careful not to

scratch or mar the lens.

Lamp Replacement

Be sure to replace the lamp when the message "Replace The Lamp" appears on the screen. If you continue to use the lamp after 1100 hours of usage, the lamp will not turn on. To replace the lamp, follow all instructions on page E-46.

Fire and Shock Precautions

* The openings should never be covered or blocked by placing the

product on a bed, sofa, rug, or other similar surface.

* Prevent foreign objects such as paper clips and bits of paper from

falling into the projector. Do not attempt to retrieve any objects that fell into the projector.

* Do not insert any metal objects such as a wire or screwdriver into

the projector. If something should fall into the projector, immediately disconnect the power cord from the projector and have the object removed by a qualified service person.

* Do not place any liquids on top of the projector.

Do not look into the lens while the projector is on. Serious damage to your eyes could result.

Important Safety Information

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

The above cautions are given on the bottom of the product.

CAUTION

To turn off main power, be sure to remove the plug from the power outlet. The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

DOC compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorientate or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

RISK OF ELECTRIC SHOCK DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREW.

Please read this manual carefully before using the projector and keep the manual handy for future reference.

POWER

ON OFF

STATUS

POWER

ON OFF

POWER

STATUS

Main power ON

Main power OFF

Tur ning ON or OFF Main Power

Make all hookups before turning on the main power.

To turn on the main power:

Press the POWER switch down until it is in the depressed position.

To turn off the main power:

Press the POWER switch until it is in the protruded position.

On condition

Off condition

Light in orange

Indicator OFF

Page 3

E – 3

1) Read these instructions.

All the safety and operating instructions should be read before the product is operated.

2) Keep these instructions.

The safety and operating instructions should be retained for future reference.

3) Heed all warnings.

All warnings on the product and in the operating instructions should be adhered to.

4) Follow all instructions.

All instructions should be followed.

5) Do not use this apparatus near water.

Do not use this product near water, near a bathtub, in a wet basement or near a swimming pool and the like.

6) Cleaning

Clean only with dry cloth.

7) Ventilation

Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Heat

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Grounding or Polarization

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Power-Cable Protection

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Attachments/Accessories

Only use attachments/accessories specified by the manufacturer.

12) Transportation

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

IMPORTANT SAFETY INSTRUCTIONS

13) Lightning

Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Servicing

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Page 4

E – 4

Major Features

High Image Quality

Use of a Digital Micromirror Device (DMDTM) chip that is based on Texas Instrument's Digital Light Processing (DLP

) technology

enables images of high contrast and high detail.

䡵 DLP technology gives rise to devices that exhibit high response

speed, which in turn enables excellent moving picture characteristics and smooth images.

䡵 Use of a high-performance progressive scan converter provides

reproduction of film-like images.

䡵 Built-in color filters of high purity permit the reproduction of vivid

color images.

Quiet Design

PLUS Vision Corporation's quiet design technology has resulted in a great reduction of fan noise which allows quiet performance that doesn't interfere with the enjoyment of movie watching in an indoor environment.

Installation Flexibility

The compact design (of about B5 paper size: 182 x 257 mm / 7.2 x 10.1 inch) and mere 2 kg / 4.4 lbs weight has resulted in a projector that can be carried anywhere indoors for room-to-room portability.

* Digital Light Processing, DLP, Digital Micromirror Device and DMD are trademarks of Texas Instru-

ments Incorporated.

* DLP technology is the combination of DLP technology and digitally control DMDTM, super micro

electronic components which replace LCD technology.

*VGA and XGA are trademarks or registered trademarks of International Business Machines Corpo-

ration in the USA. * S-VGA is a registered trademark of Video Electronics Standards Association. * TMDSI is a trademark of Silicon Image, Inc.

All company and/or product names are trademarks and/or registered trademarks of their respective manufacturers.

Page 5

E – 5

Table of Contents

Important Safety Information ................................ E-2

IMPORTANT SAFETY INSTRUCTIONS ...................... E-3

Major Features ................................................. E-4

Accessories Check ............................................ E-6

Names of the Main Unit Parts ...............................E-7

Using the Storage Case ......................................................... E-9

Attaching the Supplied Adjusters .......................................... E-9

Names of the Remote Control Parts ...................... E-10

Preparing the Remote Control ............................. E-11

Inserting the Batteries ......................................................... E-11

Remote Control Range ........................................................ E-11

The Procedure Up to Projecting to the Screen .......... E-12

Placement Guide ............................................ E-13

Projection Distance and Screen Size ................................... E-13

Power Cord Connections ................................... E-16

Power Cord Connections ..................................................... E-16

Connecting Video Equipment and Personal Computers

...... E-17

Connections with VIDEO and S-VIDEO Connectors ............. E-17

Connections with YCbCr/YPbPr Connectors ....................... E-18

Connection with RGB and DVI-D Connector ........................ E-19

Turning ON or OFF Main Power ........................... E-21

Tur ning ON or OFF Main Power ........................................... E-21

Tur ning ON or OFF Power.................................................... E-21

Adjustment of the Projection Screen ..................... E-22

Projection Screen Position Adjustment ............................... E-22

Adjustment of Screen Size and Focus ................................. E-22

Input Selection .................................................................... E-23

Selection of Aspect Ratio .................................................... E-23

Input Screen and Aspect Ratio Selection Screen ................. E-24

Operation with the Remote Control ....................... E-25

Tur ning ON Power/STANDBY .............................................. E-25

Input Selection .................................................................... E-26

Selection of Aspect Ratio .................................................... E-27

Automatic Adjustment of the Input Signal ........................... E-27

Using the On-Screen Menu ................................ E-28

Menu List ..................................................... E-31

Video Adjustments [Picture 1]............................. E-33

Adjusting the Brightness ..................................................... E-33

Adjusting the Contrast ......................................................... E-33

Adjusting the color .............................................................. E-33

Adjusting the tint ................................................................. E-34

Adjusting the Sharpness ..................................................... E-34

Adjusting the White Balance ................................................ E-34

Adjusting the Clock Frequency of the Input Signal .............. E-35

Adjusting the Phase of the Input Signal .............................. E-35

Input Video Adjustments [Picture 2] ...................... E-36

Adjusting the Sharpness of the Video Image ....................... E-36

Adjusting the Sharpness When Expanding/Compressing ....E-36

ProScan Mode Settings ....................................................... E-36

Movement of Screen Display Position ................................. E-37

Gamma Settings .................................................................. E-37

Video Signal Color System Settings .................................... E-38

Format Settings ................................................................... E-38

Color Space Settings ........................................................... E-38

Setting of White Emphasis .................................................. E-38

Setup .......................................................... E-39

Adjustment of Keystone Distortion ...................................... E-39

Screen Projection System Settings ..................................... E-39

Background Color Settings .................................................. E-40

Auto Standby Settings ......................................................... E-40

LED Display Settings ........................................................... E-40

On-Screen Display Settings [Option] ..................... E-41

On-Screen Display Language Settings ................................ E-41

Moving the Menu Display Position ......................................E-41

On-Screen Display Duration Setting .................................... E-41

Resetting, Storing, and Information [Info.] ............. E-42

Saving and Loading of Video Adjustments .......................... E-42

Returning to Standard Settings ........................................... E-43

Resetting the Lamp Timer ................................................... E-43

Viewing the Lamp Timer/Resolution and Frequency............ E-43

Troubleshooting.............................................. E-44

When the STATUS Indicator Is Lit/Flashes............... E-45

Replacing the Lamp Cartridge............................. E-46

Cleaning ...................................................... E-48

Table of Supported Frequencies .......................... E-49

Specifications ................................................ E-50

Main Unit External View .................................... E-51

Page 6

E – 6

Accessories Check

Remove the main unit and the accessories from the box and check that the following items are included. Should an accessory be missing, please contact your store of purchase.

SET

ESC

IDE

Remote control⳯1

Controls the projector.

AA Batteries⳯2

These batteries are for the remote control. Insert the batteries at time of purchase. See → Page E-11.

Power cable (1.8 m / 5.9 feet)

This power cord supplies power to the unit. See → Page E-16 about connections.

S-Video cable (3 m / 9.8 feet) No. 771709100

This cable is used when the output connector of the equipment to be connected is an S-video connector. Connections are described on → Page E-17.

Users Manual⳯1

Includes information about handling of the projector, the operation method, and precautions.

Quick Start Guide⳯1

Consolidates the procedures from setup to projecting the picture.

Quick Start Guide

User's Manual

Adjuster⳯2 / Screw⳯2

The adjusters and screws are required for fine vertical adjustment of the projector. See → Page E-9 for attachment and Page E-22 for adjustment.

Page 7

E – 7

Names of the Main Unit Parts

Ventilation outflow holes

These ventilation outflow holes used for cooling the main unit and discharge the heat of the lamp.

Attention!

Pay special attention to the ventilation outflow holes. The heat from the lamp is discharged from the ventilation outflow holes.

Remote control sensor

The remote control signal is received here. → Page E-11

Air intake hole

This is an air intake hole used for cooling the main unit.

Air intake hole

AC IN connector

The supplied power cable is connected here. → Page E-16

POWER switch

This is the main power switch. → Page E-16

POWER/STATUS

ON/STANDBY

ASPECT

SOURCE

POWER/ (STANDBY) indicator

On and Standby operation modes are indicated when this indicator is flashing green or lit orange. The indicator is not lit when the POWER switch is "off." → Page E-21

ASPECT button

This button selects the aspect ratio (i.e., the ratio of screen width and height) of the input video. → Page E-23

SOURCE button

This button selects the input sugnal of the main unit that will be used for the connections . → Page E-23

ZOOM ring

This adjusts the size of the projected picture.

→

Page E-22

STATUS indicator

Lit/flashing serve to indicate the main unit temperature, lamp, lamp cover, lamp cartridge, and fan conditions.

→

Page E-45

ON/STANDBY button

This button is used to switch ON the power and set the unit to the STANDBY mode. → Page E-21

FOCUS ring

This adjusts the focus of the projected picture.

→

Page E-22

Page 8

E – 8

Names of the Main Unit Parts

DVI-D RGB

S-VIDEO

VIDEO

Pb/Cb

Pr/Cr

Theft prevention locking hole

(See below)

Air intake hole

This is an air intake hole used for cooling the main unit.

Ventilation outflow hole

This ventilation outflow hole is used for cooling the main unit and discharges the heat of the lamp.

DVI-D RGB

S-VIDEO

VIDEO

Pb/Cb

Pr/Cr

S-VIDEO connector

This is connected with the S-VIDEO output connector of the equipment to be connected. → Page E-17

DVI-D connector

This is connected with the (24-pin) DVI-D output connector of the equipment to be connected. → Page E-19

RGB Connector

This is connected with the RGB output connector (mini D-Sub 15 pin) of the equipment to be connected. → Page E-17

YPbPr/YCbCr Connector

This is connected with the YPbPr output connector or YCbCr output connector of the equipment to be connected. → Page E-18

CTRL connector

This connector is for service personnel only. (A seal is applied prior to shipping from the factory.) End users should not use this connector. Doing so by end users may cause breakdown.

Theft Prevention Lock

The theft prevention lock is supported by the Micro Saver Security System manufactured by Kensington Technology Group.

VIDEO connector

This is connected with the VIDEO output connector of the equipment to be connected. → Page E-17

Page 9

E – 9

Names of the Main Unit Parts

Attaching the Supplied Adjusters

The supplied adjusters are required for vertical adjustment of the projector. See → Page E-22 about "Using the Adjusters"

1. Remove a rubber pad of each front foot.

Note: The rubber pads are bonded. Being carful not to mar the plastic part of the front feet, remove the rubber pads.

2. After putting projections on the back of the supplied adjuster into depressions of the front feet, tighten the screws.

Front adjuster

These feet are used for height adjustment. → (See below)

Rear adjuster

These feet are used for height adjustment. → Page E-22

Lamp cover

This cover is removed when replacing the lamp cartridge of the light source. → Page E-46

Page 10

E – 10

Names of the Remote Control Parts

ENU

ASPECT

VIDEO

/YPbPr

ON/STANDBY

VIDEO

RGB

DVI

RGB

DVI

Remote control transmitter

The infrared signal is sent from this part.

SET

ESC

ASPECT

VIDEO

/YPbPr

ON/STANDBY

VIDEO

RGB

DVI

SV CV RGB DVI

ASPECT button

This button selects the vertical and horizontal ratio of the screen of the input video.

→

Page E-23

These buttons are used for the selection of the input.

For further information about input selection, see

→

Page E-23

S-VIDEO button

This switches the input to the S-VIDEO signal.

VIDEO/YPbPr button

This switches the input to the VIDEO, YCbCr, or YPbPr signal.

RGB button

This switches the input to the RGB signal.

DVI button

This switches the input to the DVI-D signal.

ON/STANDBY button

This button is used to switch ON the power and set the unit to the STANDBY mode. → Page E-21

These buttons are used for menu operations.

→

Page E-28 "Using the On-Screen Menu"

MENU button

This is used in the selection of the menu name when displaying the menu on the projection screen.

ESC button

This is used when closing the menu.

SET button

This is used to set the menu items. Automatic adjustment of the RGB input signal is performed when the menu is closed.

Cursor buttons (왗 왘왖왔)

These are used in the selection of the menu name, item name, and contents.

Note: Handling of the Remote Control * Do not drop the remote control or handle it inappropriately.

* Do not expose the remote control to water or other liquids. Should the remote control become wet, wipe it dry immediately. *Try to avoid use in hot and/or humid locations. * Remove the batteries from the remote control when it is not going to be used for a long period. * Some operations (such as menu operations) are available only through the use of the remote control and attention should be given to its careful use.

Page 11

E – 11

Preparing the Remote Control

Inserting the Batteries

When using the remote control for the first time, install the batteries that were supplied. When replacing batteries, purchase two of the same type of AA battery.

Press and at the same time lift the battery case cover at the rear of the remote control to remove it.

Follow the markings on the inside of the case and insert the batteries in the correct plus (+) and minus (-) directions.

First insert the tabs of the battery case cover, then press it closed.

Tabs

Remote Control Range

Point the remote control toward the remote control sensor located at the rear of the main unit and operate. The range over which the main unit will receive the remote control signal is roughly as follows: within 20° above and 20° below a line perpendicular with respect to the sensor and within 40° to the left and 40° to the right. The transmission range is about 7 m /

23.0 feet.

Remote control sensor

Remote control transmitter

Approximately 7 m / 23.0 feet

Note:

* Exposure of the main unit's remote control sensor or the remote control transmitter to bright light or the obstruction of the signal by an obstacle located in the

pathway may prevent operation.

* The remote control will not function when the batteries are exhausted.

Page 12

E – 12

The Procedure Up to Projecting to the Screen

POW

ON OFF

Position the projector → Page E-13 "Projection Distance and Screen Size"

Determine the locations to place the screen and the projector.

Connecting the power cable → Page E-16 "Power Cord Connections"

Connect the video equipment and personal computer

Connect your equipment to the projector.

→ Page E-17 "Connections with VIDEO and S-VIDEO Connectors" → Page E-18 "Connections with YCbCr Connectors (COMPONENT)" → Page E-19 "Connections with RGB and DVI-D Connector"

Switching on the main power → Page E-21 "Turning ON or OFF Main Power"

Switching on the power → Page E-21 "Turning ON or OFF Power"

Properly adjust the projection image to the screen → Page E-22 "Projection Screen Position Adjustment"

Properly adjust the screen size and focus → Page E-22 "Adjustment of Screen Size and Focus"

Selecting input equipment → Page E-23, 26 "Input Selection"

Selecting the vertical and horizontal aspect of the picture (i.e., the ratio of screen width and height)

→ Page E-23, 27 "Selection of Aspect Ratio (i.e., Ratio of Screen Width to Screen Height)"

2 3

4 5 6 7 8 9

Note:

* Please purchase a commercially available screen

separately.

*A commercially available cable is required for the

connection with the RGB connector of the personal computer and an optional cable (Order code 27-060) is required for the connector with the DVI-D connector.

* An optional cable (Order code 27-062) is required

for the connection of a DVD player or high definition video equipment with the YPbPr/YCbCr connector.

*A commercially available video cable is required

for the connection of video equipment with the VIDEO connector.

* Please refer to the various manuals of the audio

system for information about audio system connections.

About DLP projectors

Though careful attention is paid to providing optimum quality, please note that with DLP type projectors, in rare cases there may be black spots or bright spots among the picture elements.

Note: During projection, some streaks of light may be visible outside of the projected picture; this is not a product fault.

Page 13

E – 13

Placement Guide

Use this information as a guide to find the rough screen size when the projector is placed at a certain location, or to find out the approximate size of a screen that will be required. The projection distance over which focussing is adjustable is 1.2 m (3.9 feet) to 7.6 m (24.9 feet) from the lens surface of the main unit. The projector should be placed within this range.

1 Projection Distance and Screen Size

Screens with 4:3 Aspect Ratio (at an output size of 800 x 600)

This projection screen aspect ratio supports multiple uses. The screen is placed within the projection distance range that corresponds to the screen size designation. Within this range, the screen size can be adjusted with the zoom ring.

Note: This is the projection distance (at an output size of 800 x 600) for aspect ratio settings of "Full" or "Auto." The projection distance will differ when "Thru" or other settings have been selected and the image is projected to fill the screen. When establishing a fixed placement, the distance could be outside the zoom adjustment range and a test projection should be conducted. → Page E-24 "Input Screen and Aspect Ratio Selection Screen"

160.0 (wide) x 120.0 (high) inch

200

inch

406.4 (wide) x 304.8 (high) cm

Screen Size

Screen Size Designation (Inches)

120.0 (wide) x 90.0 (high) inch

150

inch

304.8 (wide) x 228.6 (high) cm

96.0 (wide) x 72.0 (high) inch

120

inch

243.8 (wide) x 182.9 (high) cm

3.9 – 4.6 feet /

1.2 –1.4m

4.3 – 4.9 feet /

1.3 –1.5m

6.2 – 7.2 feet / 1.9 – 2.2m

8.5 – 9.8 feet / 2.6 – 3.0m

10.5 –12.5 feet / 3.2 – 3.8m

12.5 –15.1feet / 3.8 – 4.6m

15.7–18.7 feet / 4.8 – 5.7m

21.0 – 24.9 feet / 6.4 – 7.6m

80.0 (wide) x 60.0 (high) inch

100

inch

203.2 (wide) x 152.4 (high) cm

64.0 (wide) x 48.0 (high) inch

80 inch

162.6 (wide) x 121.9 (high) cm

48.0 (wide) x 36.0 (high) inch

60 inch

121.9 (wide) x 91.4 (high) cm

32.0 (wide) x 24.0 (high) inch

40 inch

81.3 (wide) x 61.0 (high) cm

30.4 (wide) x 22.8 (high) inch

38 inch

77.2 (wide) x 57.9 (high) cm

Wide to Telephoto

Projection Distance

Lens surface of the main unit

H dimension: Height from center of projector lens to bottom edge of screen.

200 inch: 23.9 inch/60.6 cm 150 inch: 17.9 inch/45.5 cm 120 inch: 14.3 inch/36.4 cm 100 inch: 11.9 inch/30.3 cm

80 inch: 9.6 inch/24.3 cm 60 inch: 7.2 inch/18.2 cm 40 inch: 4.8 inch/12.1 cm 38 inch: 4.5 inch/11.5 cm

Page 14

E – 14

Screens with 16:9 Aspect Ratio (at an output size of 848 x 480)

These are the projection distances for screens of 16:9 aspect ratio used for the viewing of DVD and other squeezed screen applications. This projector uses an output size of 848 x 480 pixels for home theater applications and enables the projection of a high definition 16:9 aspect ratio. The screen is placed within the projection distance range that corresponds to the screen size designation. Within this range, the screen size can be adjusted with the zoom ring.

Note: This is the projection distance when an aspect ratio of [16:9] has been selected. Selection of "Full", "Auto" or other settings at this projection distance will result in the top and bottom of the image extending beyond the screen. When establishing a fixed placement, the distance could be outside the zoom adjustment range and a test projection should be conducted. → Page E-24 "Input Screen and Aspect Ratio Selection Screen"

Placement Guide

169.9 (wide) x 95.6 (high) inch

195

inch

431.6 (wide) x 242.8 (high) cm

160.3 (wide) x 90.2 (high) inch

184

inch

406.4 (wide) x 228.6 (high) cm

Screen Size

130.7 (wide) x 73.5 (high) inch

150

inch

331.6 (wide) x 187.7 (high) cm

104.5 (wide) x 58.8 (high) inch

120

inch

265.3 (wide) x 150.1 (high) cm

87.1 (wide) x 49.0 (high) inch

100

inch

221.1 (wide) x 125.1 (high) cm

69.7 (wide) x 39.2 (high) inch

inch

176.8 (wide) x 100.1 (high) cm

52.2 (wide) x 29.4 (high) inch

inch

132.6 (wide) x 75.1 (high) cm

34.8 (wide) x 19.6 (high) inch

inch

88.4 (wide) x 50.1 (high) cm

33.1 (wide) x 18.6 (high) inch

inch

84.0 (wide) x 47.6 (high) cm

4.3 – 4.5 feet /

1.3 –1.4m

4.3 – 4.9 feet /

1.3 –1.5m

6.6 – 7.5 feet / 2.0 –2.3m

8.9 –10.2 feet / 2.7 – 3.1m

10.8 –12.8 feet / 3.3 – 3.9m

13.1–15.4 feet / 4.0 – 4.7m

16.4 –19.4 feet / 5.0 – 5.9m

Wide to Telephoto

Projection Distance

21.0 – 24.9 feet / 6.4 –7.6m

19.7– 23.6 feet / 6.0 – 7.2m

Screen Size Designation (Inches)

Maximum screen size that allows focussing of a 16:9 aspect ratio image with 848 x 480 output size

This is the distance when an image of 16:9 aspect ratio is projected to horizontally fill a 200" 4:3 aspect ratio screen.

Lens surface of the main unit

H dimension: Height from center of projector lens to bottom edge of screen.

195 inch: 35.8 inch/91.5 cm 184 inch: 33.8 inch/84.9 cm 150 inch: 27.5 inch/69.8 cm 120 inch: 22.0 inch/56.4 cm 100 inch: 18.3 inch/46.8 cm 80 inch: 14.7 inch/37.3 cm 60 inch: 11.0 inch/28.0 cm 40 inch: 7.3 inch/18.6 cm

38 inch: 7.0 inch/17.8 cm

Page 15

E – 15

Installation Height of Projection Screen [Reference] Once the installation location and position have been decided, the projection height should be checked. In the case of large screen sizes, there are instances where the image cannot be projected within the floor to ceiling height. The required installation height can be found using the following formula: Screen size vertical cm(inch) + H cm(inch) + 7.2 cm(2.8 inch) + Stand height

Example: Using a 150" 4:3 screen and placing the projector horizontally, the required installation height will be

228.6 cm(90 inch) + 45.5 cm(17.9 inch) + 7.2 cm(2.8 inch) = 281.3 cm(110.7 inch) (without a stand) An installation room with a height of 240 cm(94.5 inch) will have insufficient room height even when the projector is placed on the floor. (Note that the rear adjusters can be raised to lower the projection screen image.)

Placement Guide

Screen size vertical dimension

H dimension

7.2 cm(2.8 inch)

Screen size top edge dimension measured from floor

Lens center

Stand dimension

Note:

* Determine the screen size after checking the height and width of the room in which the screen will be installed as well as checking that there are no obstacles

located in the path between the lens and the screen.

* The larger the screen size becomes, the darker the image will be.

Placing the projector to the rear of the screen to project the image will require the use of a translucent type screen. * The height from the feet of the main unit to the center of the lens is 7.2 cm (2.8inch). * There is a tolerance of ±5% due to design values.

Attention!

• Do not install in location that will reach high or low temperatures. (Operation temperature: within 5°C (41°F) to 35°C (95°F))

•To raise the projection screen position, place the unit on a stable and strong support.

• Make efforts to ensure that sunlight or room illumination does not strike the screen. The more such extraneous light is shielded, the higher the contrast and more attractive the image that will be obtained.

Page 16

E – 16

Power Cable Connections

2 Power Cable Connections

Use the supplied power cord to connect the power connector of the main unit with the power outlet.

POWER

ON OFF

POWER switch

POWER/ indicator

Firmly insert all the way.

Power cable (supplied)

Firmly insert all the way.

To wall outlet

Attention! For pluggable equipment, install the projector as near to the power outlet socket that is easily accessible.

Do not switch off the main power or disconnect the power cable unless the POWER/

indicator is lit orange. Doing so could shorten the life of the lamp or possibly cause the unit to malfunction. When the unit is set to off (and the LED is not lit) using the menu [Setup] → [LED] items, the indicator flashes green for 1 minute, then goes off. Likewise, at this time the main power should not be switched off and the power cord should not be disconnected.

Before using the projector, first connect 1 and then

; after using, unplug 3 and then 4.

Page 17

E – 17

Connecting Video Equipment and Personal Computers

By connecting this unit with video equipment and using a DVD player or other source in combination with an audio/video amplifier and speaker system will allow you to enjoy convincing home theater. Connecting the unit to a personal computer will permit presentation data to be projected as a large screen display in conferences and lectures.

3 Connections with VIDEO and S-VIDEO Connectors

These are connections made with equipment that is equipped with a video output connector or an S-video output connector such as video decks, DVD players, laser disc players, TV tuners, etc. Connect such equipment to the VIDEO or S-VIDEO connector of this projector.

D V

I-D

R L

- V I

D E

V I

D E

b /C

/ C r

RGB

S-VIDEO

VIDEO

Pb/Cb

Pr/Cr

VIDEO

AUDIO

S-VIDEO

VIDEO

AUDIO

Connections with the Video Output Connector

Connect to the green jack.

Video cable (Commercially available)

Connect to the yellow output jack marked VIDEO.

Connections with the S-VIDEO Output Connector

S-video cable (supplied)

Connect to the output jack marked S-VIDEO. Check before inserting, since this connector must be oriented properly.

Note:

* Connection can be made with the S1 video and S2 video output connectors,

but the control signals will not be operable in the projector depending on video equipment.

* Please refer to the various manuals for information about video equipment

and audio/video amplifier and speaker system connections.

Attention!

Before making connections, check that the main power supply is switched off for the projector and the equipment that is to be connected.

Page 18

E – 18

D V

R G

C T

- V

E O

V I D

E O

P b /

C b

r /

C r

S-VIDEO

VIDEO

Pb/Cb

Pr/Cr

COMPONENT

YCbCr

YPbPr

3 Connections with YCbCr/YPbPr Connectors

These are connections made with equipment such as DVD players that have YCbCr output connectors or YPbPr output connectors. Make connections with the YPbPr/YCbCr connectors of this projector.

Component signal cable (available as an option) (order code: 27-062)

Make connections to the YCbCr output jacks marked COMPONENT or COLOR-DIFFERENCE SIGNAL.

The YPbPr/YCbCr connectors and the cables are color coded. Match the same colors when making connections.

Note:

* When inputting a YPbPr signal, format selection or color space selection

may be required. → page E-38

* Please refer to the various manuals for information about video equipment

and audio/video amplifier and speaker system connections.

Connecting Video Equipment and Personal Computers

Component signal cable (available as an option) (order code: 27-062)

Make connections to the YPbPr output jacks marked COMPONENT or COLOR-DIFFERENCE SIGNAL.

Page 19

E – 19

V I

G B

T R

- V

D E

I D E

b /

C b

r /

C r

DVI-D RGB

VIDEO

DVI-D

MONITOR OUTPUT

3 Connection with RGB and DVI-D Connector

These connections are made with personal computers that have a monitor output RGB connector (analog signal) or a DVI-D connector (digital signal). Connect personal computers having a mini D-Sub 15-pin RGB connector to the RGB connector of the projector and connect personal computers having a DVI standard DVI-D connector to the DVI-D connector of the projector.

Check the following before making connections.

* The resolution through this unit is S-VGA 800 x 600 dots. VGA is enlarged and displayed and XGA is compressed and displayed.

Input of resolutions higher than S-XGA will not be displayed. Such resolutions should be converted to a displayable resolution at the personal computer side. Check with the "Table of Supported Frequencies" on Page E-49.

* The setting method of the personal computer will vary depending on your personal computer. For information, read the instruc-

tion manual for your personal computer, read the on-line help, or contact the manufacturer of your personal computer.

Plug in, then turn the screws to secure.

DVI-D cable (available as an option) (

order code: 27-060

)

Note:

* This unit uses a digital interface 24-pin DVI-D connector. Digital signal TMDS (Transition Minimized Differential Signalling) of the DVI (Digital Visual Interface)

standard is used. (Analog RGB signals cannot be input.)

* Personal computers that are not equipped with a DVI-D connector require a digital graphics board furnished with a DVI-D connector. * Before making connections, turn off the main power to the projector and all the connected equipment.

Connecting Video Equipment and Personal Computers

RGB cable (Commercially available)

Connect with the monitor output or the connector that provides picture display.

Page 20

E – 20

Obtaining an External Output Signal from a Notebook Computer.

When projection will be with a notebook computer connected, knowledge will be required for the cable connection and notebook computer startup procedure as well as the operation that follows notebook startup. Please consult the instruction manual of your notebook computer or the on-line help while performing the following procedure.

1 Check whether a signal is being sent from the notebook computer to the projector.

An indication appearing on the liquid crystal display of the notebook computer does not necessarily mean that an external output signal is- being output. Reference: When the frequency under [Info.] of the projector menu is displayed as 0 kHz, 0 Hz, it indicates that an external output signal is not being output from the personal computer. → Page E-43 "Viewing the Lamp Timer/Resolution and Frequency"

2 Should a signal not be output from the notebook computer, please try the operation described

below.

For an IBM PC/AT, DOS/V computer, press the [Fn] key plus any one of the [F1] to [F12] keys. (See the table below.)

Manufacturer Model Key

akia All computers Fn + F2

COMPAQ ARMADA Series Fn + F4

PRESARIO Series Fn + F3

DELL All computers Fn + F8

FUJITSU All computers Fn + F10

GATEWAY All computers Fn + F3

IBM All computers Fn + F7

NEC All computers Fn + F3

Panasonic All computers Fn + F3

SHARP All computers Fn + F5

SONY All computers Fn + F7

SOTEC All computers Fn + F3

TOSHIBA All computers Fn + F5

Note: Table information is current to June 2001.

Connecting Video Equipment and Personal Computers

Note: When the liquid crystal display of the notebook computer and the projector are displayed at the same time, the projected image might not be correct even though the liquid crystal screen shows a proper display. Should this occur, stop the simultaneous display of the notebook computer and try the mode with external output only. (Try an operation such as that described in aforementioned Step 2 and try closing the liquid crystal panel which might result in external output only.)

Page 21

E – 21

Turning ON or OFF Main Power

POWER

ON OFF

STATUS

POWER

ON OFF

POWER

STATUS

Main power ON

Main power OFF

4 Turning ON or OFF Main Power

Before turning the main power, check that the power is switched off the equipment that is to be connected and the connection is finished.

To turn on the main power:

Press the POWER switch down until it is in the depressed position.

On condition

Off condition

Light in orange

Indicator OFF

To turn off the main power:

Press the POWER switch until it is in the protruded position.

Attention!

• Do not switch off the main power or disconnect the power cable unless the POWER/

indicator is lit orange. Doing so could shorten the life of the lamp or possibly cause the unit to malfunction. When the unit is set to ON (and the LED is not lit) using the menu [Setup] → [LED] items, the indicator flashes green for 1 minute, then goes off. Likewise, at this time the main power should not be switched off.

•To save power, switch off the main power when not in use. When the main unit or remote control ON/STANDBY button is used to set the projector to the standby mode (POWER/

indicator is lit orange), the cooling fan continues to operate.

5 Turning ON or OFF Power

The ON/STANDBY buttons of the main unit and the remote control have the same function. A description using the main unit button is provided here.

To turn on the power:

Press the ON/STANDBY button for about 2 seconds. The projection screen will brighten in about 40 seconds.

Note: When the unit is set to off (and the LED is not lit) using the menu [Setup]

→

[LED] items, the indicator flashes green for 60 seconds, then goes off.

Setting standby mode

Press and hold down the ON/STANDBY button for about 2 seconds.

To s witch on the power again, leave at least 60 seconds before doing so.

ON/STANDBY

STANDBY

STATUS

POWER

STATUS

POWER

STATUS

POWER

Light in orange

Light in green

Power ON

Standby

Flashing orange

Flashing green

Flashing for 60 seconds

Note:

* When a signal is not being input while projecting onto the projection screen, "No Signal" is displayed to indicate the condition. The background color of the screen

will be blue at this time. The background color can be changed to black by via [Setup] → [Background] of the menu. → Page E-40 "Background Color Settings"

* When the power is switched on, the input selection and aspect selection conditions will be the same as the conditions that existed when the power was switched

off.

* Adjustments and setting values that were made via menu operations will be stored even when the main power has been switched off or the power cord has been

disconnected.

When the power won't switch on

* When the internal temperature is abnormally high, the power will not be switched on to protect the equipment. Wait for a while and then try switching on the power

again.

* Should the STATUS indicator be lit or flashing, please see "When the STATUS Indicator Is Lit/Flashing" on Page E-45.

POWER

ON OFF

POWER/ indicator

ON/STANDBY button

POWER switch

Page 22

E – 22

Adjustment of the Projection Screen

Operations include the adjustment of the image position that is projected to the screen and the adjustment of the focus as well as the input selection and the selection of the aspect ratio. Perform these operations with the power of the connected equipment switched on and the video signal input to the projector.

6 Projection Screen Position Adjustment

Adjust the projection image to the screen

(1) If the image is shifted to the left or right, move the main unit horizontally. (Align the center of the screen and the center of

the lens of the main unit.) (2) If the image is shifted vertically, move the image up or down with the adjuster. (3) A projection image such as that illustrated in the diagram is the result of the projector not being perpendicular to the

screen. Set the projector so that it is pointing straight toward the screen. (4) If the image shows keystone distortion, adjust using menu operations. → Page E-39 "Adjustment of Keystone Distortion"

(1)

(2)

(3)

(4)

7 Adjustment of Screen Size and Focus

Using the Adjusters

Turn the zoom ring and adjust the screen size, then turn the focus ring and adjust the focus.

To lower the projection position:

Raise the rear adjusters up

To raise the projection position:

Attach the supplied two adjusters to the front feet. See page E-9 "Attaching the Supplied Adjusters". After folding the rear adjusters, rotate the right/left front adjuster to fine-adjust the height. (Adjustable range: 0 to 5 mm/ 0 to 0.2 inch)

Note: The zoom ring allows adjustment of approximately 20% of the maximum screen size. (When the zoom ring is at the center position, an adjustment of approximately ±10% will be possible.)

ZOOM ring

FOCUS ring

Page 23

E – 23

8 Input Selection

Press the SOURCE button and select the desired connector.

SOURCE

A press of the SOURCE button will display the selected input. Each press of the button moves the selection one step in the sequence: S-VIDEO → (VIDEO/YCbCr/YPbPr) → RGB → DVI

The selection will not change while "Now Searching" is displayed. The input display will remain for a while before disappearing. To change the duration of the display, see → Page E-41 "On-Screen Display Du- ration Setting."

S-VIDEO

YCbCr YPbPr

VIDEO

RGB

DVI

Input display

Press the ASPECT button and select the desired aspect ratio.

9 Selection of Aspect Ratio (i.e., Ratio of Screen Width to Screen Height)

ASPECT

A press of the button will display the aspect selection display.

The aspect ratio is the ratio of the width and height of the screen.

Full

Aspect

S-VIDEO

16:9(LB) 16:9 Real Thru

Full

Aspect

16:9(LB) 16:9

Real Thru

S-VIDEO

Full

Auto

Aspect

16:9

Thru

DVI

[VIDEO, S-VIDEO, YCbCr and YPbPr Input Selection]

[RGB and DVI Input Selection]

Aspect Selection Display

Press the ASPECT button during the appearance of the aspect selection display and make the selection. Each press of the button moves the cursor and switches the aspect ratio.

A diagram of the a sample image with different aspect ratios is carried on the next page. The aspect selection display will remain for a while before disappearing. To change the duration of the display, see → Page E-41 "On-Screen Display Duration Setting."

This completes the projection screen adjustments.

Note:

* The remote control provides direct selec-

tion from the VIDEO button, S-VIDEO button, YCbCr button, and DVI button.

* When a function other than [AUTO] is

specified at the source selection display, the projector searches for the specified signal among VIDEO/YCbCR/YPbPr.

→

Page E-23 "Input Selection"

* When a signal is not input to the selected

connector, "No Signal" is displayed.

* When RGB or DVI is selected and "No Sig-

nal" is displayed, check with [Info.] on the menu.

→

Page E-43 "Viewing the Lamp Timer/

Resolution and Frequency" When the frequency is displayed as "0 kHz,

0 Hz," there is no signal from the personal computer. → See Page E-20 "Obtaining an External Output Signal from a Notebook Computer."

Note:

* The aspect ratio selection display will not

appear unless a signal is input. Play the video of the equipment.

* Match the aspect ratio of the image of the

connected equipment with the aspect ratio of the projected image of this unit, or adjust the image of a 16:9 aspect to the desired format.

* When the aspect ratio differs, a circle, for

example, will be projected as an ellipse.

* The selected aspect ratio for each input is

stored.

Note:

* For information about operation with the

remote control, see → Page E-25 "Operation with the Remote Control"

*To adjust or set the brightness, picture,

or other matters, display the menu on the projection screen and perform the operation. → Page E-28 "Using the On-Screen Menu"

Adjustment of the Projection Screen

Cursor: Displays the currently selected contents position.

Page 24

E – 24

Input Screen and Aspect Ratio Selection Screen

"XXXXX••••••"

Select Full

The image is projected to fill the entire screen. Aspect 16:9 screens will be longer than wide.

Video signal

Projection image with Through selection

Projection image when selected

Select Auto

(only with RGB or DVI selection)

While maintaining the aspect ratio of the personal computer, the image is enlarged or reduced so that no parts protrude beyond the screen and the image is projected to fill the screen. Aspect 16:9 screens will be black at the top and bottom.

Select 16:9

This returns the squeezed screen to a 16:9 screen and projects it. The output size becomes 848 x 480.

Select Real

(S-VIDEO, VIDEO, YCbCr and YPbPr only)

This maintains a video image aspect ratio of 4:3 and projects it. Images with a 16:9 aspect ratio will become vertically elongated (4:3).

Select Thru

This projects the input image as is. When the input resolution is higher than that of the projector (800 x 600), the image will extend beyond the screen, and when lower, the image will be smaller than the screen. Video images may have a different aspect ratio.

The top and bottom black portions are cut. Subtitles are also cut.

The output size becomes 848 x 480.

[Display Examples]

Squeeze signal VGA 640 x 480

16:9 screen

Letter box

Select 16:9 (LB)

(S-VIDEO, VIDEO, YCbCr, and YPbPr only)

The image of long sideways movie material is projected to fill the entire screen without the top and bottom black portions.

This maintains a letterbox image aspect ratio and projects it on a 16:9 screen. This will make the image quality better than "Full".

Adjustment of the Projection Screen

Page 25

E – 25

Operation with the Remote Control

Point the remote control toward the remote control sensor of the main unit and operate.

ESC

ASPECT

VIDEO

/YPbPr

ON/STANDBY

VIDEO

RGB

DVI

SV CV RGB DV I

SET

ASPECT button

This button selects the vertical and horizontal ratio of the screen of the input video.

These buttons are used for the selection of the input signal.

For further information about input selection.

S-VIDEO button

This switches the input to the S-VIDEO signal.

VIDEO/YPbPr button

The source selection display will appear.

RGB button

This switches the input to the RGB signal.

DVI button

This switches the input to the DVI-D signal.

ON/STANDBY button

This button is used to switch ON the power and set the unit to the STANDBY mode.

These buttons are used for menu operations.

→

Page E-28 "Using the On-Screen Menu"

MENU button

This is used in the selection of the menu name when displaying the menu on the projection screen.

ESC button

This is used when closing the menu.

SET button

This is used to set the menu items.

Cursor buttons (왗 왘왖왔)

These are used in the selection of the menu name, item name, and contents.

ON/STANDBY

POWER

STATUS

Tur ning ON Power/STANDBY

Press the POWER button of the main unit and turn on the main power.

To turn on the power:

Check that the POWER/ indicator of the main unit is lit orange.

Press the ON/STANDBY button for about 2 seconds.

The power will be switched on, the indicator will flash green (for one minute) and then the indicator will be lit green. The projection screen will brighten in about 40 seconds.

Setting standby mode:

Press and hold down the ON/STANDBY button for about 2 seconds.

The indicator will flash orange (for 60 seconds) and then be lit orange.

Attention!

When switching off the main power or disconnecting the power cable First press ON/STANDBY button of the remote control or the main unit to set the standby mode (in which the indicator will be lit orange) and then switch off the main power. If the main power of the main unit is switched off without setting the standby mode, this could shorten the life of the lamp or possibly cause damage due to the heat of the lamp.

Light in orange

Light in green

Power ON

Standby

STATUS

POWER

Note: To save electrical power when not using the unit, switch off the main power. When doing so, wait until the flashing orange indicator is lit steadily.

This is used for selection of VIDEO, YCbCr, and YPbPr input signals.

SET button

Automatic adjustment of the RGB input signal is performed when the menu is closed and the SET button is held down for more than 1 second.

Page 26

E – 26

Input Selection

Press the desired input selection button.

VIDEO

/YPbPr

VIDEO

RGB

DVI

SV CV RGB DVI

S-VIDEO

YCbCr YPbPr

VIDEO

RGB

DVI

Input selection display

S-VIDEO button

A press of the button will switch the input to the S-VIDEO input signal.

VIDEO/YPbPr button

The source selection display will appear. (If the source selection display is not displayed, press the button again.) *[AUTO] is selected at the initial setting. A press of the SET button causes the source selection display to disappear and starts an automatic search of the VIDEO/YCbCr/YPbPr input signal. * The input display at the [AUTO] setting will be [Video/YCbCr/YPbPr].

RGB button

A press of this button switches the unit to the RGB input signal.

DVI button

A press of this button switches the unit to the DVI input signal.

The input display will remain on for a while before disappearing. To change the duration of the display, see → Page E-41 "On-Screen Display Duration Setting."

VIDEO/YCbCr/YPbPr Signal Selection

The input signal is specified directly and projected.

A press of the VIDEO/YPbPr button displays the source selection display. (If the source selection display is not displayed, press the button again.)

Select the signal with the cursor (왖왔) button or the VIDEO/YPbPr button. A press of the SET button causes the source selection display to disappear, performs a search for the specified signal and projects it.

Note:

* When the power is switched on, the input

selection conditions that existed when the power was switched off will be in effect.

* When a signal is not input to the selected

connector, "No Signal" is displayed.

* When RGB or DVI is selected and "No Sig-

nal" is displayed, check with [Info.] on the menu.

→

Page E-43 "Viewing the Lamp Timer/

Resolution and Frequency" When the frequency is displayed as "0 kHz,

0 Hz," there is no signal from the personal computer. → See Page E-20 "Obtaining an External Output Signal from a Notebook Computer."

Operation with the Remote Control

AUTO

VIDEO

SOURCE

YCbCr

YPbPr

AUTO

VIDEO

SOURCE

YCbCr

YPbPr

Note:

* When the source selection is specified as

[AUTO], upon switching to the VIDEO/ YCbCr/YPbPr signal, a search for the signals will be made in order and it may take a while before the signal is displayed. The signal can be projected quickly when it has been specified directly.

* Conversely, for example, when connection

is made to a video system that switches the input signal from a YCbCr signal to a YPbPr signal, having previously set the source selection to [AUTO], another press of the VIDEO/YPbPr button (i.e., the SOURCE button on the projector) will perform automatic identification of the signal.

Source selection display

Page 27

E – 27

Selection of Aspect Ratio (i.e., Ratio of Screen Width to Screen Height)

ASPECT

Press the ASPECT button and select the desired aspect ratio.

Full

Aspect

S-VIDEO

16:9(LB) 16:9

Real Thru

Full

Aspect

16:9(LB) 16:9

Real Thru

S-VIDEO

Full

Auto

Aspect

16:9

Thru

DVI

[VIDEO, S-VIDEO, YCbCr and YPbPr Input Selection]

[RGB, DVI Input Selection]

Aspect Selection Display

A press of the button will display the aspect selection display.

The aspect ratio is the ratio of the width and height of the screen.

Press the ASPECT button while the aspect selection display is shown and make the selection. Each press of the button moves the cursor and switches the aspect ratio. Also the selection can be made with the cursor (왖왔) buttons.

Note:

* The aspect ratio selection display will not

appear unless a signal is input. Play the video of the equipment.

* Match the aspect ratio of the image of the

connected equipment with the aspect ratio of the projected image of this unit, or adjust the image of a 16:9 aspect to the desired format.

* When the aspect ratio differs, a circle, for

example, will be projected as an ellipse.

* The selected aspect ratio for each input is

stored.

Operation with the Remote Control

Cursor: Displays the currently selected contents position.

Automatic Adjustment of the Input Signal

This automatically adjusts the projected RGB signal to an optimum condition. Only the RGB, DVI and YPbPr (480p) signals can be automatically adjusted.

Holding down the SET button for more than 1 second starts the automatic adjustment.

During the adjustment, [AUTO] is display at the center of the screen. When the menu is displayed, the button that is associated with the menu item will be operational; therefore, press the ESC button to close the menu before making this adjustment.

Note:

* This automatically adjusts the stripe pat-

terns, color infidelity, and flicker which arise from pixel shift. When proper adjustment cannot be obtained with automatic adjustment upon pressing the SET button, please adjust manually.

See E-35 "Adjusting the Clock Frequency of the Input Signal" and "Adjusting the Phase of the Input Signal".

SET

Page 28

E – 28

Using the On-Screen Menu

Only menu operation methods will be described here. Refer to this page should you need to clarify matters during menu operations. See the various pages for information about menu functions and performing adjustments and settings. To perform adjustments and settings, the video is projected and adjustments are made to the optimum condition. The remote control should be pointed toward the remote control sensor of the projector and operated. To return the various items that have been changed with the menu to their default values (i.e., the condition that existed at the time of purchase), see → Page E-43 "Returning to Standard Settings."

SET

ESC

ASPECT

VIDEO

/YPbPr

ON/STANDBY

VIDEO

RGB

DVI

SV CV RGB DVI

Names and functions of the buttons used in menu operations

MENU button

Used to display menus and in selection of menu names.

ESC button

Used to close the menu.

SET button

Used to set the menu item.

Cursor buttons (왗 왘왖왔)

These are used in menu name selection and in the contents selection.

Picture1

Language En De Fr It Es

- Menu Position Duration 10 sec.

Picture2 Setup Info.

VIDEO

Option

Names and functions of the menu screens

Menu names

These are the menu headings. When a menu is selected, there is a switch to the heading screen. The selected menu name appears in blue.

Input selection display

This is the currently selected input signal screen.

[Setting Screen Display Example]

Selected contents

Select the desired contents. Selected characters appear in red.

Item name

This is the name of the adjustment or setting. The selected item name appears in navy blue. A press of the SET button at a location where only the item name is displayed results in a change to the selection contents screen. The contents will change for the item name depending on the input selection.

Cursor

The item at the cursor position can be adjusted or set. Move the cursor with the cursor buttons.

Note:

* If a remote control operation is not performed in about

10 seconds (i.e., the initial setting time) from the time the menu is displayed, the menu will automatically close.

→

Page E-41 "On-Screen Display Duration Setting"

* The display position of the menu can be changed.

→

Page E-41 "Moving the Menu Display Position"

Page 29

E – 29

Press the MENU button and display the menu.

Display of the Menu

Picture1

Brightness 0 Contrast 0 Color 0 Tint 0 Sharpness 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Press the button again and select the menu name.

The selected menu name will appear in navy blue.

Selection of the Menu Name

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Each press of the MENU button switches the menu one step in the sequence of [Picture 1] → [Picture 2] → [Setup] → [Option] → [Info.]

Press the cursor button (왖왔) and select the item name.

Align the cursor with the desired item name. The selected item name will appear in deep blue.

Selection of the Item Name

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Press the cursor button (왗왘) and make the adjustment (or selection).

Adjust (or select) to produce the best picture.

Making Adjustments and Settings

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Adjustment bar

SET

[Adjustment Item Examples]

(Continued on the next page)

Note:

* The menu name will change also

when the cursor (왗왘) button is pressed.

* When using the cursor button to se-

lect the menu name, the cursor must be in the menu name column (at the very top) or else selection will not be possible.

* When the cursor is not located at the

menu name, the selected menu name will appear in blue.

* For information about the contents

list that is displayed in the menu, see

→

Page E-31 "Menu List."

Note: When the cursor is not located at the menu name, the selected menu name will appear in blue.

Note:

* For adjustment items, adjustment

values are indicated by the increase and decrease of the adjustment bar and the numerical value. Adjust for the optimum picture while viewing the image projected to the screen.

* The selected characters will appear

in red for items that select On, Off, and other titles.

Using the On-Screen Menu

Page 30

E – 30

Press the ESC button and close the menu display.

The selected menu name will appear in navy blue.

Exit

Sub menu items

Items that display only an item name have a sub menu.

Picture1 Keystone Mode Keystone

- Installation -

Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Floor-Front

Floor-Rear Ceiling-Front Ceiling-Rear

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation -

Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

SET

1) Press the SET button to display the sub menu.

ESC

Note: The selection operation will differ for the sub menu depending on the item contents.

Note: A transition to item selection of the menu will not be possible while the sub menu is being displayed. To select the next item, press the ESC button, close the menu again, then perform the selection.

Note:

* Even without pressing the ESC but-

ton, waiting a while will result in the menu closing (when the display duration setting has elapsed).

* The adjustment and setting values

will be stored even when the power is switched off or the power cord is disconnected.

Using the On-Screen Menu

SET

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation -

Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

3) Press the SET button to finalize. The sub menu will close.

SET

2) For setup, select with the cursor button (왖왔).

Page 31

E – 31

Picture1 Brightness 0 Contrast 0 Clock frequency 0 Phase 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

RGB

Option

Picture1 Brightness 0 Contrast 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

DVI

Option

Menu List

This is a list of menu item names. See the reference page for information about the adjustment and setting method. The display contents of the item name will differ depending on the input selection.

Indications such as those below appear along side the input selections (i.e., input signals) that permit adjustment or setting.

Adjustment or setting is permitted for any input that is selected. (The item name will appear in the menu.)

Adjustment or setting is permitted only when the "VIDEO, S-VIDEO, and YCbCr" indication appears at the time of the listed input selection. (In this case, the item name will be displayed only when a VIDEO, S-VIDEO, or YCbCr signal is input.

Picture 1

Picture1 Brightness 0 Contrast 0 Color 0 Tint 0 Sharpness 2 Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Picture1 Brightness 0 Contrast 0 Color 0 Sharpness 2 Color Temp. Low Normal High Custom

Picture2 Setup Info.

YCbCr

Option

Picture 2

Picture1

Video Filter 2

3Zoom Filter

Video AutoProScan Mode Gamma CustomGraphicsFilmVideo Color System Auto

Picture2 Setup Info.

VIDEO

Option

[VIDEO, S-VIDEO, and YCbCr Input Selection]

"Adjusting the Sharpness of the Video Image"

→ Page E-36

"Adjusting the Sharpness When Expanding/Compressing"

→ Page E-36

"ProScan Mode Settings" → Page E-36

"Gamma Settings" → Page E-37

"Video Signal Color System Settings" → Page E-38

Various inputs allowed

VIDEO, S-VIDEO, and YCbCr

"Adjusting the Clock Frequency of the Input Signal"

→ Page E-35

"Adjusting the Phase of the Input Signal" → Page E-35

"Adjusting the Brightness" → Page E-33

"Adjusting the Contrast" → Page E-33

"Adjusting the color" → Page E-33

"Adjusting the tint" → Page E-34

"Adjusting the Sharpness" → Page E-34

"Adjusting the White Balance" → Page E-34

[VIDEO and S-VIDEO Input Selection]

[DVI Input Selection]

[RGB and YPbPr Input Selection]

[YCbCr Input Selection]

Picture1 Brightness 0 Contrast 0 Tint 0 Clock frequency 0 Phase 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

YPbPr

Option

[YPbPr Input Selection]

Page 32

E – 32

Picture1

Language En De Fr It Es

- Menu Position Duration 10 sec.

Picture2 Setup Info.

VIDEO

Option

"On-Screen Display Language Settings" → Page E-41

"Moving the Menu Display Position" → Page E-41

"On-Screen Display Duration Adjustment" → Page E-41

[Common Inputs]

Info.

[VIDEO, S-VIDEO and YCbCr Input Selection]

"Saving and Loading of Video Adjustments" → Page E-42

"Returning to Standard Settings" → Page E-43

"Resetting the Lamp Timer" → Page E-43

Picture1

- Default -

- Lamp Timer Reset -

--------------------------- Status: 100 . 500

Lamp Timer: 1 hrs (Total 1 hrs)

Resolution: Frequency:

800 X 600

H: 37.8KHz V: 60Hz

--------------------------- Status: 100 . 500 Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

Picture1

User Memory Save Load

- Default -

- Lamp Timer Reset -

Picture2 Setup Info.

DVI

Option

VIDEO

Menu List

"Viewing the Lamp Timer/Resolution and Frequency"

→ Page E-43

[RGB and DVI Input Selection]

Setup

Picture1

Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

"Adjustment of Keystone Distortion" → Page E-39

"Screen Projection System Settings" → Page E-39

"Background Color Settings" → Page E-40

"Auto Standby Settings" → Page E-40

"LED Display Settings" → Page E-40

[Common Inputs]

[RGB and DVI Input Selection]

Picture1

Zoom Filter 3

White Peak

- Pan -

Off On

Gamma CustomGraphicsFilmVideo

Picture2 Setup Info.

RGB

Option

"Movement of Screen Display Position" → Page E-37

"Setting of White Emphasis" → Page E-38

Auto Auto

Picture1

Zoom Filter 3

Gamma

- Pan -

Format Color Space

CustomGraphicsFilmVideo

Picture2 Setup Info.

YPbPr

Option

[YPbPr Input Selection]

"Format Settings" → Page E-38

"Color Space Settings" → Page E-38

Page 33

E – 33

Video Adjustments [Picture 1]

These are picture-related adjustments. For information about performing menu operations, see → Page E-28 "Using the On-Screen Menus."

Picture1

Brightness 0 Contrast 0 Tint 0 Clock frequency 0 Phase 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

YPbPr

Option

Picture1

Brightness 0 Contrast 0 Clock frequency 0 Phase 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

RGB

Option

Picture1

Brightness 0 Contrast 0 Color 0 Tint 0 Sharpness 2 Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Picture1

Brightness 0 Contrast 0 Color 0 Sharpness 2 Color Temp. Low Normal High Custom

Picture2 Setup Info.

YCbCr

Option

Picture1

Brightness 0 Contrast 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

DVI

Option

Preparation

* Project the image. * Press the MENU button to display the menu, then select [Picture 1].

[VIDEO and S-VIDEO Input Selection]

[YCbCr Input Selection] [RGB Input Selection]

Color

Adjusting the color

This is used in the adjustment of powerful colors and natural colors.

Press the cursor button (왖왔) and align the cursor with "Color", then adjust with the cursor (왗왘) button.

Cursor (왗) Button: Lighter color Cursor (왘) Button: Deeper color

Picture1

Brightness 0

Contrast 0

Color

Tint 0 Sharpness 1 Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Contrast

Adjusting the Contrast

This is used in the adjustment of powerful images and natural images.

Press the cursor button (왖왔) and align the cursor with "Contrast", then adjust with the cursor (왗왘) button.

Cursor (왗) Button: Less dense picture Cursor (왘) Button: Denser picture

Picture1

Brightness 0

0Contrast

Color 0 Tint 0 Sharpness 1 Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Brightness

Adjusting the Brightness

The brightness of the image will differ depending on whether the room is bright or dark. Make adjustments to suit your preference.

Press the cursor button (왖왔) and align the cursor with "Brightness", then adjust with the cursor (왗왘) button.

Cursor (왗) Button: Darker Cursor (왘) Button: Brighter

Picture1 Brightness 0

Contrast 0 Color 0 Tint 0 Sharpness 1 Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Note: The adjustment values of the image can be stored and called according to the various inputs.

→

Page E-42 "Saving and Loading of

Video Adjustments"

Various inputs allowed

VIDEO, S-VIDEO and YCbCr

[DVI Input Selection]

[YPbPr Input Selection]

Page 34

E – 34

Color Temperature

Adjusting the White Balance

This is the input picture white color selection or white and black level correction, and serves to adjust the color reproducibility.

Press the cursor button (왖왔) and align the cursor with the desired item, then adjust with the cursor (왗왘) button.

Low: Warm white (White with heightened yellow) Normal: The white of sunlight High: Cool white (White with heightened blue)

Custom adjustments

Press the (왗왘) cursor button and align the cursor with [Custom], then press the SET button. The custom adjustment screen will appear. Press the (왖왔) cursor button to select the color, then adjust with the cursor (왗왘) button.

Adjust each of the red, green, and blue brightness levels.

After the adjustment, press the SET button to finalize.

Picture1

Brightness 0 Contrast 0 Color 0 Tint 0 Sharpness 1

Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Note: Color temperature (or white balance) refers to the white color that becomes the reference of color representation. White color is expressed by the mixture of red, green, and blue light. The color temperature adjustment serves to adjust the proportions of this mixture. The color representation on the screen will change depending on the environment including room illumination.

[Custom Adjustment Screen]

Video Adjustments [Picture 1]

Sharpness

Adjusting the Sharpness

This is used in the adjustment of picture sharpness.

Press the cursor button (왖왔) and align the cursor with "Sharpness", then adjust with the cursor (왗왘) button.

Cursor (왗) Button: Softer picture Cursor (왘) Button: More distinct picture

Picture1

Brightness 0 Contrast 0 Color 0 Tint 0

Sharpness 1

Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Tint

Adjusting the tint

This is used in the adjustment of skin tones, etc.

Press the cursor button (왖왔) and align the cursor with "Tint", then adjust with the cursor (왗왘) button.

Cursor (왗) Button: Heightened red Cursor (왘) Button: Heightened green

Picture1

Brightness 0

Contrast 0 Color 0

Tint 0

Sharpness 1 Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Note: Adjustment is not possible with PAL, SECAM video input.

Picture1

Brightness Contrast Color Tint Sharpness

Color Temp. Low Normal High Custom

Picture2 Setup Info.

VIDEO

Option

Red

Green

Blue

Various inputs allowed

VIDEO, S-VIDEO and YCbCr

VIDEO, S-VIDEO and YPbPr

Page 35

E – 35

Clock frequency

Adjusting the Clock Frequency of the Input Signal

This is adjusted when light and dark vertical bands appear on the projection screen of the RGB and YPbPr input signal. This is usually adjusted automatically at the time of signal selection; however, this adjustment is made when the automatic adjustment cannot effectively make the adjustment.

Press the cursor (왖왔) buttons and align the cursor with [Clock frequency], then use the cursor buttons (왗왘) to remove the vertical bands and render the screen brightness uniform.

Picture1

Brightness 0 Contrast 0

Clock Frequency 0

Phase 0 Color Temp. Low Normal High Custom

Picture2 Setup Info.

RGB

Option

Note:

*A light and dark striped pattern will

appear when there is lack of correspondence between the input signal and the pixel position of the projector. This is adjusted by the adjustment of the clock frequency.

* When the image extends beyond the

screen or is smaller than the screen, check whether the [Aspect] setting is set to "Full."

→

Pages E-23 and E27 "Selection of Aspect Ratio (i.e., Ratio of Screen Width to Screen Height)

Phase

Adjusting the Phase of the Input Signal

This is adjusted when a color shift or flickering appears on the projection screen of the RGB or YPbPr input signal. This is usually adjusted automatically at the time of signal selection; however, this adjustment is made when the automatic adjustment cannot effectively make the adjustment.

Press the cursor (왖왔) buttons and align the cursor with [Phase], then use the cursor buttons (왗왘) to make the color shift or flickering incon- spicuous.

Picture1

Brightness 0 Contrast 0 Clock Frequency 0

Phase 0

Color Temp. Low Normal High Custom

Picture2 Setup Info.

RGB

Option

RGB and YPbPr

Video Adjustments [Picture 1]

RGB and YPbPr

Page 36

E – 36

Input Video Adjustments [Picture 2]

These functions adjust the input video signal. See → Page E-28 "Using the On-Screen Menu" for information about performing menu operations.

Picture1 Video Filter 2

3Zoom Filter

Video AutoProScan Mode Gamma CustomGraphicsFilmVideo Color System Auto

Picture2 Setup Info.

VIDEO

Option

Picture1 Zoom Filter 3

White Peak

- Pan -

Off On

Gamma CustomGraphicsFilmVideo

Picture2 Setup Info.

RGB

Option

Auto Auto

Picture1 Zoom Filter 3

- Pan -

Format Color Space

Picture2 Setup Info.

YPbPr

Option

Gamma CustomGraphicsFilmVideo

Preparation

* Project an image. * Press the MENU button to display the menu, then select [Picture 2].

Video Filter

Adjusting the Sharpness of the Video Image

This adjustment is used to reduce the roughness and provide a clear picture.

Press the cursor button (왖왔) and align the cursor with the desired item, then adjust with the cursor (왗왘) but- ton. Adjust to your preference while viewing the picture. Adjustment can be made from 0 to level 4.

Picture1

Video Filter 2

2Zoom Filter

Video AutoProScan Mode Gamma CustomGraphicsFilmVideo Color System Auto

Picture2 Setup Info.

VIDEO

Option

Zoom Filter

Adjusting the Sharpness When Expanding/Compressing

This adjusts the sharpness of the picture at the time of pixel conversion in the selection of the aspect ratio.

Picture1 Video Filter 2

2Zoom Filter

Video AutoProScan Mode Gamma CustomGraphicsFilmVideo Color System Auto

Picture2 Setup Info.

VIDEO

Option

ProScan Mode

ProScan Mode Settings

Set this according to the movie material.

Press the cursor button (왖왔) and align the cursor with the [ProScan Mode], then select with the (왗왘) button.

Video: This setting progressive an input signal on the as-

sumption that it is a normal interlaced signal.

Auto: This setting automatically determines whether an

input signal is the movie material(24 frames) or the video material (normal interlaced signal) to use progressive scanning.

Picture1 Video Filter 2

2Zoom Filter

Video AutoProScan Mode

Gamma CustomGraphicsFilmVideo Color System Auto

Picture2 Setup Info.

VIDEO

Option

Note: The greater the number of adjustment level becomes, the sharper an image is. The closer to 0 the number of adjustment level becomes, the softer an image is.

Note: The higher the level, the more proper it is for high resolution.

[VIDEO, S-VIDEO, and YCbCr Input Selection]

[YPbPr Input Selection] [RGB and DVI Input Selection]

Various inputs allowed

VIDEO, S-VIDEO and YCbCr

Page 37

E – 37

Input Video Adjustments [Picture 2]

Pan

Movement of Screen Display Position

This is used to move the screen position at the time of RGB, DVI and YPbPr input selection.

Press the cursor button (왖왔) and align the cursor with [Pan], then press the SET button. The menu display will close and the cursor display will appear.

Adjust the screen position horizontally with the cursor (왗왘) button and vertically with the cursor (왖왔) button.

Gamma

Gamma Settings

These are settings of the tone of the image.

Press the cursor (왖왔) button and align the cursor with [Gamma], then select with the cursor (왗왘) button.

Video: This is a gamma adjustment value suited to video

signals.

Film: This is a gamma adjustment value suited to movies. Graphics: This is a gamma adjustment value suited to

graphics such as computer images.

Custom adjustments

This adjustment permits the creation of a desired gamma curve. This is performed while viewing the target image. Select [Custom] with the cursor (왗왘) button, then press the SET button. The custom adjustment screen will be displayed.

1. Press the cursor (왖) button and align the cursor with the index.

2. Select the adjustment point with the cursor (왗왘) but- ton.

3. Select the color that is to be adjusted with the cursor (왖왔) button, then adjust with the cursor (왗왘) but- ton. When required, adjust other adjustment points in the same manner.

4. Press the SET button to finalize. The custom adjustment screen will close.

Picture1 Video Filter 2

2Zoom Filter

Video AutoProScan Mode

Gamma CustomGraphicsFilmVideo

Color System Auto

Picture2 Setup Info.

VIDEO

Option

Picture1 Video Filter Zoom Filter ProScan Mode

Gamma CustomGraphicsFilmVideo

Color System

Picture2 Setup Info.

VIDEO

Option

Index

Red

Green

Blue

Note: See → Page E-43 "Return- ing to Standard Settings" for information about returning to the standard setting values. Note that other adjustments and settings will also be reset.

Note:

The display position can only be moved when a large picture with a resolution of 800 x 600 or greater is displayed in the through mode.

Note: Index (1 to 31) indicates adjustment point of a 32nd part of input values between 0 and 255.

YPbPr, RGB and DVI

Various inputs allowed

Picture1

Zoom Filter 3

White Peak

- Pan -

Off On

Gamma CustomGraphicsFilmVideo

Picture2 Setup Info.

RGB

Option

Position

SET

Page 38

E – 38

Color System

Video Signal Color System Settings

These settings are of the color system of the composite video signal. This function is normally set to Auto. If the color system cannot be identified on Auto, set it manually.

Press the (왖왔) cursor button and align the cursor with [Color System], then press the SET button. The color system selection display will appear. Press the cursor (왖왔) button to match the composite video signal system of the input equipment, then press the SET button to finalize.

Picture1 Video Filter Zoom Filter ProScan Mode Gamma

Color System Auto

Picture2 Setup Info.

VIDEO

Option

Auto

NTSC NTSC4.43 PAL PALM PALN PAL60 SECAM

Note:

* The video signal created by add-

ing the color signal to the brightness signal is termed the composite video signal and differs depending on the country. The color system sets the method of this color signal.

*PAL-M cannot be identified au-

tomatically and will need to be set manually. Note that when PAL-M and other color systems are set manually, the "No Signal" display will not appear during absence of signal input. The background color under such circumstances will be entirely black.

Input Video Adjustments [Picture 2]

VIDEO, S-VIDEO and YCbCr

Format

Format Settings

Usually, [Auto] is specified.

Press the cursor (왖왔) buttons and align the cursor with [Format], then press the SET button. The format selection display will appear. Press the cursor (왖왔) button to match the format of the input signal, then press the SET button to finalize.

Picture1 Zoom Filter Gamma

Format Auto

Color Space

Picture2 Setup Info.

YPbPr

Option

Auto

480P

576P

720P

1080i

Note: This is the format setting for the digital broadcast specifications of Japan.

YPbPr

Picture1 Zoom Filter Gamma Format

Color Space

Picture2 Setup Info.

YPbPr

Option

ITU-R.BT709

Auto

ITU-R.BT601

SMPTE240M

Auto

Color Space

Color Space Settings

This is set when projecting a YPbPr signal that appears as a reddish or greenish image.

Press the cursor (왖왔) buttons and align the cursor with [Color space], then press the SET button. The color space selection display will appear. Press the cursor (왖왔) button to match the color space of the normal image, then press the SET button to finalize.

Note: When the YPbPr signal undergoes conversion to the red, green, and blue colors that express the projector image, the correct colors cannot be expressed unless a system is used that will conform to the color difference conversion system of the input signal. Color space is the function that selects this.

YPbPr

Picture1 Zoom Filter 3

White Peak

- Pan -

Off On

Gamma CustomGraphicsFilmVideo

Picture2 Setup Info.

RGB

Option

White Peak

Setting of White Emphasis

This is used to emphasize and display the whites of text or diagrams on personal computers.

Press the cursor (왖왔) buttons and align the cursor with [White peak], then press the cursor (왗왘) buttons and set.

Off: Switches off the white peak function On: Emphasizes the highlights

RGB and DVI

Page 39

E – 39

Setup

These settings are used when setting up the projector. See → Page E-28 "Using the On-Screen Menu" for information about performing menu operations.

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Preparation

* Project an image. * Press the MENU button to display the menu, then select [Setup].

Keystone Mode / Keystone

Adjustment of Keystone Distortion

This adjusts keystone distortion in the vertical direction. Adjust so that left and right sides are parallel.

Press the cursor (왖왔) button and align the cursor with [Keystone Mode], then press the cursor (왗왘) button and select the mode.

Normal: Corrects while maintaining the aspect ratio. Full: Corrects by enlarging the width at the top to a full

sized screen.

Picture1

Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Full

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Note: Keystone distortion arises when the projector is not installed level, or when the screen is inclined which results in a difference in the distance of upper and lower projection points. Keystone correction compensates for this. This projector has two correction modes.

Installation

Screen Projection System Settings

These settings are for setting projection from the front of the screen and from the rear of the screen.

Press the cursor (왖왔) button and align the cursor with [Installation], then press the SET button. The setup screen will be displayed. Press the cursor (왖왔) button and select the setting condition, then press the SET button to finalize.

Floor - Front

Projection is from the front of the screen.

Floor - Rear

Projection is from the rear of the screen.

Ceiling - Front

Ceiling installation with projection from the front.

Ceiling - Rear

Ceiling installation with projection from the rear.

Note: When projecting from the rear of the screen, a translucent type screen is required.

Picture1 Keystone Mode Keystone

- Installation -

Background Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Floor-Front

Floor-Rear Ceiling-Front Ceiling-Rear

Floor - Front

Floor - Rear

Ceiling - Front

Ceiling - Rear

Consult your dealer or installer for special installation such as ceiling mounting.

Adjustment of Keystone Distortion

Press the cursor (왔) button and align the cursor with [Keystone], then press the cursor (왗왘) button to correct the key- stone distribution.

Normal

Various inputs allowed

Page 40

E – 40

Background

Background Color Settings

This sets the background color when a signal is not being input to the connector of the projector.

Press the cursor (왖왔) button and align the cursor with [Background], then make the selection with the cursor (왗왘) button.

Blue: Displays a blue screen. Black: Displays a black screen.

Note: When the menu display is closed after making the setting, the color will change to the background color that has been set.

Setup

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation -

Background

Auto Power Off LED

Picture2 Setup Info.

VIDEO

Option

Auto Power Off

Auto Standby Settings

This setting automatically sets the power to the standby mode when a no-signal condition has existed at the connector of the projector for 5 minutes or longer.

Press the cursor (왖왔) button and align the cursor with [Auto Power Off], then make the selection with the cursor (왗왘) button.

Off: Not operational On: Operational

LED

LED Display Settings

This setting is used when the light of the POWER/ STANDBY indicator (LED) of the main unit is objectionable during projection in a dark room.

Press the cursor (왖왔) button and align the cursor with [LED], then make the selection with the cursor (왗왘) button.

Off: Switches off the LED. On: Lights the LED.

Note:

* The projector will automatically

switch to the standby mode when the "No Signal" display has been projected for about 5 minutes. Some video equipment such as video tape decks are designed to display a blue background when playback has finished. In this instance, the projector is receiving a signal and so it does not produce its own background.

*To project an image again, press

the ON/STANDBY button and switch on the power.

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background

Auto Power Off

LED

Picture2 Setup Info.

VIDEO

Option

Picture1 Keystone Mode Normal Full

Blue Black

+0Keystone

Off On

- Installation Background Auto Power Off

LED

Picture2 Setup Info.

VIDEO

Option

Attention!

When this function is used to switch off the LED and the background color is set to black, the projector may mistakenly be assumed to be in the standby mode. Do not mistakenly switch off the main power or disconnect the power cord. Doing so may shorten the life of the lamp and cause breakdown.

Various inputs allowed

Page 41

E – 41

On-Screen Display Settings [Option]

These settings are for the menu and language that will be displayed on the screen. See → Page E-28 "Using the On-Screen Menu" for information about performing menu operations.

Picture1 Language En De Fr It Es

- Menu Position Duration 10 sec.

Picture2 Setup Info.

VIDEO

Option

Preparation

Press the MENU button to display the menu, then select [Option].

Language

On-Screen Display Language Settings

This is the setting of the language that is displayed on screen when the input is switched, a menu is displayed, etc.

Press the cursor (왖왔) button and align the cursor with [Language], then press the cursor (왗왘) button and select the language.

En: English, De: German, Fr: French, It: Italian, Es: Spanish, : Korean, : Chinese, : Japanese

Picture1

Language En De Fr It Es

- Menu Position Duration 10 sec.

Picture2 Setup Info.

VIDEO

Option

Menu Position

Moving the Menu Display Position

This function changes the display position of the onscreen menu.

Press the cursor (왖왔) button and align the cursor with [Menu Position], then press the SET button and the display will change to the menu position display.

Use the cursor (왗 왘왖왔) buttons to move the [Menu Position] display.

Picture1 Language En De Fr It Es

- Menu Position -

Duration 10 sec.

Picture2 Setup Info.

VIDEO

Option

Picture1 Language En De Fr It Es

- Menu Position -

Duration 10 sec.

Picture2 Setup Info.

VIDEO

Option

Menu Position

Duration

On-Screen Display Duration Setting

This is the setting of the time that is displayed on screen when the input is switched, a menu is displayed, etc.

Press the cursor (왖왔) button and align the cursor with [Duration], then press the cursor (왗왘) button and se- lect the desired time. Settings can be made from 5 seconds to 30 seconds in 5-second units.

Picture1 Language En De Fr It Es

- Menu Position -

Duration 10 sec.

Picture2 Setup Info.

VIDEO

Option

Note: Even when a different language has been selected, "No Signal" will appear in English.

Various inputs allowed

Page 42

E – 42

Resetting, Storing, and Information [Info.]

This function performs resetting and the display of information for the method of using the user memory, the default values of adjustments and settings, and the lamp timer. See → Page E-28 "Using the On-Screen Menu" for information about performing menu operations.

Picture1 User Memory Save Load

- Default -

- Lamp Timer Reset -

Status : 100 . 500

Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

VIDEO

Preparation

Press the MENU button to display the menu, then select [Info.].

User Memory

Saving and Loading of Video Adjustments

This function saves video adjustment and setting values, and can load them when required. Saving can be performed independently for the inputs of VIDEO, S-VIDEO, YCbCr, YPbPr, RGB and DVI.

Items that can be saved: Menu items of [Picture 1] and [Picture 2]

Saving

1. Project the saved image and adjust the menu items of [Picture 1] and [Picture 2]. The menu can be closed without causing problems. When closing, select [Info.] of the menu.

2. Press the cursor (왖왔) button and align the cursor with [User Memory], then press the cursor (왗왘) button and select [Save], finally press the SET button.

3. The message display will change to "Save User Memory." Press the SET button.

(Press the SET button while the message is displayed.)

This will save the video adjustment and setting values of the current input mode.

1. Project the image that you want to save.

2. Press the cursor (왖왔) button and align the cursor with [User Memory], then press the cursor (왗왘) button and select [Load], finally press the SET button.

3. The message display will change to "Load User Memory." Press the SET button. (Press the SET button while the message is displayed.)

This will change the image to that of the loaded adjustment and setting values.

Picture1

User Memory Save Load

- Default -

- Lamp Timer Reset -

Status : 100 . 500

Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

VIDEO

Picture1

User Memory Save Load

- Default -

- Lamp Timer Reset -

Status : 100 . 500

Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

VIDEO

Save User Memory

Load User Memory

Note:

* User memory is used when you wish to view the same video adjustment

conditions again. For example, when, for the purpose of movie enjoyment, optimum adjustments are made in fine detail and the image is saved [Save]. Even when adjustments are changed in normal use, the movie can be viewed with the stored adjustment values when viewing it for full appreciation.

* Saved [Save] adjustment values are stored even when the main power is

switched off or the power cord is disconnected.

Note:

* The [Save] operation overwrites the pre-

vious adjustment values.

* Saving can be performed independently

for each input. In the load operation, the adjustment and setting values that have been saved for that input mode are loaded.

Various inputs allowed

Page 43

E – 43

Resetting, Storing, and Information [Info.]

Default

Returning to Standard Settings

This function is used to return the adjustments and settings of the current signal to the standard settings. Select the signal you wish to return to the default settings first before doing so.

Press the cursor (왖왔) button and align the cursor with [Default], then press the SET button. The message display will change to: Press "Set" to Reset Menu. Press the SET button while the message is displayed.

This results in a return to the standard settings.

Items returned to default settings

[Option]: Language [Info.]: Lamp timer, User Memory

Picture1 User Memory Save Load

- Default -

- Lamp Timer Reset -

Status : 100 . 500

Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

VIDEO

Press "SET" to Menu Reset

Lamp Timer Reset

Resetting the Lamp Timer

This reset is used when replacing the lamp cartridge. Be certain to reset this, since it is used in the display of the lamp timer.

1. Press the cursor (왖왔) button and align the cursor with [Lamp Timer Reset], then press the SET button. The message display will change to "Lamp Timer Reset."

2. While the message is being displayed, select "No" or "Yes" with the cursor (왗왘) button, then press the SET button. The message will change to [Press “SET” to Lamp Timer Reset].

3. While the message is being displayed, press the SET button.

This will reset the lamp timer and set the time to 0.

Picture1 User Memory Save Load

- Default -

- Lamp Timer Reset -

Status : 100 . 500

Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

VIDEO

Lamp Timer Reset

No Yes

Note: Items that cannot be specified for each input will be returned to the initial settings.

Note: The projector will no longer start when the lamp timer exceeds 1,100 hours. As a result, it will not be possible to reset the lamp timer through timer operations.

Should this situation arise, set to the standby condition and press the SOURCE button and the ASPECT button of the main unit at the same time for at least 5 seconds.

When reset, the STATUS indicator will go off.

Info.

Viewing the Lamp Timer/Resolution and Frequency

This function is used to check the lamp timer (for a check of the lamp cartridge replacement time) and the resolution and frequency at the time of RGB or DVI input.

Picture1 User Memory Save Load

- Default -

- Lamp Timer Reset -

Status : 100 . 500

Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

VIDEO

Picture1

- Default -

- Lamp Timer Reset -

Status : 100 . 500

Resolution: 800 X 600 Frequency: H: 37.8KHz V: 60Hz

Lamp Timer: 1 hrs (Total 1 hrs)

Picture2 Setup Info.Option

DVI

[VIDEO, S-VIDEO and YCbCr Input Selection]

[DVI Input Selection]

Note: Replacing the lamp cartridge

and resetting the lamp timer will not reset the total number of operating hours. The total number of operating hours indicates the usage time of the projector from date of dispatch to the present.

Press "SET" to Lamp Timer Reset

Note: When the video adjustments have not been returned to the defaults, use the user memory. See

→

Page E-42 "Saving and Loading

of Video Adjustments."

Various inputs allowed

Page 44

E – 44

Troubleshooting

Check the following matters before requesting servicing.

* Has the power plug become disconnected from the outlet? * Is the lamp cover properly attached? * Has the internal temperature become high? When the internal temperature becomes

very high, to protect the unit the power will not switch on.

* Has the lamp timer exceeded 1,100 hours? The power will no longer switch on once

the timer has exceeded 1,100 hours.

* Has the connected input been selected? * Is the cable of the input connector properly connected? * Are the Picture 1 brightness and contrast adjustments (incorrectly) set to a mini-

mum? * Has the lamp burned out? * If the projector is connected to a personal computer, is a signal being output from the

personal computer? * Has a signal been input that does not correspond to the supported frequencies of the

projector? * Is the STATUS indicator flashing?

* Is the projector installed properly? * Is the keystone adjustment properly adjusted?

* Is the lens properly focussed? * Are the projection screen and the projector installed at the proper angle? * Has the projection distance exceeded the focussing range? * Is there condensation on the lens and other parts?

When the projector has been stored in a cold location and the power is switched on in

a warm location, there may be condensation on the lens and other internal optical

parts. Should this occur, wait several minutes until the condensation disappears.

* Is the input signal being supported for resolution and frequency? Check the resolu-

tion of your personal computer. * At the time of RGB input, is the clock frequency correct or shifted a little? * At the time of YPbPr input, does the format setting match the input signal or is it

different?

* When the image is broken in the horizontal or vertical direction, or the image does not

fill the entire screen, select a suitable aspect ratio.

* When a YPbPr signal is input, does the color space setting match the input signal or

is it different? * At the time of VIDEO or S-VIDEO input, is the tint adjustment correct or is it shifted a

little?

* The phase of the input signal might be shifted.

* Is an obstacle located between the remote control and the remote control sensor of

the main unit? * Is the remote control out of range for its signal to reach the sensor? * Is there strong light or a fluorescent lamp in the vicinity of the sensor? * Are the batteries weak? Try directing the remote control toward the remote control

sensor from a close distance and operating it. If there is difficulty in changing settings,

the batteries are weak. Replace the batteries with new ones.

* There might be a fault with the projector.

* Has the LED been set to off?

Problem

No power (POWER/ indicator does not light)

No video

Distorted video

Blurred video

Image position is shifted and doesn't display properly

Image is broken

The color of the whole image is strange

Characters flicker or color is not correct with RGB or YPbPr input

Remote control does not function

STATUS indicator lights or flashes

POWER/ indicator is off while projecting

Check Reference Page

E-16 E-46 E-45

E-43, 46

E-23, 26 E-17 – 19 E-33

E-45, 46 E-20

E-49

E-45

E-22 E-39

E-22 E-22 E-13 –

E-43

E-35 E-38

E-23, 27

E-38

E-34

E-35

E-11

E-11 – E-11

E-45

E-40

Page 45

E – 45

When the STATUS Indicator Is Lit/Flashes

* It is time to replace the lamp. Replace with a new lamp.

* Is the lamp cover attached properly? If not, attach it properly.

* The thermal protector has been activated. If the room temperature is high,

move the projector to a cool location. If the internal temperature of the projector is high, check the cooling fan ventilation holes and clean them if they are obstructed.

* The thermal protector has been activated. If the room temperature is high,

move the projector to a cool location. If the internal temperature of the projector is high, check the cooling fan ventilation holes and clean them if they are obstructed.

* When the thermal protector is activated and the unit is set to the standby

mode and soon thereafter the power is switched ON, the unit may not power up. Should this occur, wait for one minute and then switch it ON again.

* The lamp lighting voltage fault detection protector has been activated. Wait

for at least one minute and switch on the power again. If the unit still does not operate, please contact your store of purchase.

* The cooling fan has stopped. Consult your PLUS dealer.

* The lamp does not light. First turn off the main power, then wait at least one

minute, then switch on the power again. If the unit still does not operate, consult your dealer.

POWER

ON/STANDBY

STATUS

The faults described below are being indicated when the indicators of the projector control panel are lit or flashing.

Indicator Display

Projector Condition Action to Be Taken

Off

Lit

Flashing at 1-second intervals (0.5 s lit / 0.5 s off)

Flashing once every 4 seconds (2 s lit / 2 s off)

Flashing once every 8 seconds (4 s lit / 4 s off)

Flashing once every 12 seconds (6 s lit / 6 s off)

Normal operation

Time for lamp replacement

Cover is open

Temperature error

Lamp lighting voltage fault

Fan fault

Lamp power error

Thermal Protector

When the internal temperature of the projector becomes abnormally high, the STATUS indicator will flash (at an interval of once every 4 seconds). At the same time, the temperature protector is activated and the projector power may be switched off. Should this occur, proceed with the following actions.

1. Switch off the power and disconnect the power plug from the wall outlet.

2. Check the following matters and take the required measures. When the projector is being used in a location that has a high ambient temperature, install it in a cool location. Check the outflow and intake holes and clean them if they are obstructed.

3. Wait about 60 minutes until the temperature of the projector drops. If after having performed the above matters, the problem still has not been solved, consult your PLUS dealer.

Page 46

E – 46

Replacing the Lamp Cartridge

NOTE: The projector lamp has its usable life. The rated lamp life is about 1000 hours. However, it may become shorter depending on the conditions of usage. (The rated lamp life is the average life of the lamps produced and tested, under the test conditions of our company, for a long term.)

䡵 After the lamp has been operating for 1000 hours or longer, the STATUS indicator

will light and the message "Replace The Lamp" will appear on the screen. Also, when 1,100 hours is exceeded, the warning "Warning! System Shutdown" will be displayed for 10 seconds. Should this happen, it is time to replace the lamp cartridge. Please specify the following information when ordering a replacement lamp cartridge:

䡵 Replacement lamp model HE-3100L

Part number: 27-050

CAUTION

When replacing the lamp cartridge, switch off the power and check that the POWER/ indicator has changed to steady orange. Switch off the power switch of the projector, disconnect the power plug from the outlet, and wait about 60 minutes (for the lamp cartridge to cool) before replacing. Wait at least 60 minutes for the lamp cartridge to cool. DO NOT TOUCH THE LAMP CARTRIDGE immediately after it has been used. It will be extremely hot.

䡵 Do not remove any screws except for those mentioned in the instructions below. 䡵 Do not touch the lamp. Doing so may shorten the lamp life. 䡵 The lamp may explode if improperly mishandled. 䡵 If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can be heard

and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer or the store where the projector was purchased.

Preparation: Unplug the projector. Prepare the new lamp cartridge and a plus-headed screwdriver.

Lay a soft cloth sheet underneath the projector with its upside down to prevent scratches.

Remove the lamp cover.

q Loosen the lamp cover screw until it turns freely. w Remove the lamp cover.

Lamp cover

Remove the lamp cartridge.

q Loosen the lamp cartridge screw until it turns freely. w Hold the handle of the lamp cartridge and then pull out the

lamp cartridge.

Lamp cartridge

Page 47

E – 47

Install the new lamp cartridge.

q Install the new lamp cartridge in the direction as shown

in the drawing.

Plug

Reinstall the lamp cover.

q Insert the lamp cover until the catches fit in the grooves. w Tighten the lamp cover screw.

w Tighten the lamp cartridge screw.

(Put down the handle of the lamp cartridge.)

Groove

Reset the lamp usage hours to zero.

From the menu, select [Info.] → [Lamp Timer Reset] and then reset the lamp usage hours. See "Resetting the Lamp Timer" on page E-43.

NOTE: When the projector lamp has exceeded 1100 hours of operation, the projector will not turn on. This means you cannot reset the lamp usage on the menu. Should this happen, press SOURCE and ASPECT on the projector cabinet for at least of 5 seconds at the same time when the projector is in standby mode. When the lamp usage is reset, the STATUS indicator goes off.

[This completes the lamp replacement.]

Replacing the Lamp Cartridge

Page 48

E – 48

Cleaning a Soiled Projector Main Unit

* Wipe with a lint-free, soft, dry cloth.

When very dirty, wipe with a cloth that has been moistened with a diluted neutral detergent, then finish with a dry cloth. If a chemically-treated cloth is going to be used, please follow any written warnings.

* Do not wipe with thinner, benzene, or other solvents. Doing so could cause them to undergo qualitative changes or the coatings

may peel, etc.

* When removing the dust of the outflow and intake holes, use the brush attachment on a vacuum cleaner to clean out the dust.

Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter.

* Do not scratch or otherwise hit the projector body with your nails or other hard object, since this will cause scratches.

Dirty Lens

The lens surface has been treated with a special coating. Consult your PLUS dealer for cleaning.

Dust of the Intake and Outflow Holes

Dust that collects in the intake and outflow holes will obstruct the ventilation and cause the internal temperature to rise which could cause damage. Clean this area carefully. As a guideline, clean at least every 100 hours.

Cleaning

Attention!

* Be certain to disconnect the power plug from the power outlet before cleaning. * Do not spray or otherwise expose the projector, lens, or screen to volatile substances such as insecticides. Doing so

could cause them to undergo qualitative changes or the coatings may peel, etc.

POWER

ON OFF

* Switch off the power with the ON/STANDBY

button and check that the POWER/ indicator has changed to a steadily lit orange, then switch off the main power with the POWER switch of the main unit. Finally, disconnect the power cord.

* Clean out the holes from the outside using a

vacuum cleaner. Use the brush adapter of the vacuum cleaner to do this. Avoid using the vacuum directly without attaching the adapter as well as the use of a nozzle adapter.

Cleaning the Inside of the Projector

Cleaning of the inside of the projector is required about once a year. Failure to clean over a long period while dust has collected inside the projector could cause a fire or breakdown. Do not clean the inside of the projector by yourself. Be sure to consult your PLUS dealer.

Brush adapter

Page 49

E – 49

Table of Supported Frequencies

This projector automatically identifies the input signal from the personal computer and selects the optimum supported resolution from the table below. Note that a manual adjustment may be required depending on the input signal. Please see "Adjusting the Clock Frequency of the Input Signal" and "Adjusting the Phase of the Input Signal" on Page E-35.

Signal Resolution Frequency Support

Horizontal(kHz)

Ver tical(Hz) Analog Digital

VESA 640 x 350 31.5 70.1 쑗 –

640 x 350 37.9 85.1 쑗 – 720 x 350 31.5 70.0 쑗 – 640 x 400 31.5 70.1 쑗 – 640 x 400 37.9 85.1 쑗 – 720 x 400 31.5 70.0 쑗쑗 720 x 400 37.9 85.0 쑗 – 640 x 480 31.5 60.0 쑗쑗 640 x 480 37.9 72.8 쑗 – 640 x 480 37.5 75.0 쑗 – 640 x 480 43.3 85.0 쑗 – 800 x 600 35.2 56.3 쑗 – 800 x 600 37.9 60.3 쑗쑗 800 x 600 46.9 75.0 쑗 – 800 x 600 48.1 72.2 쑗 –

800 x 600 53.7 85.1 쑗 – 1024 x 768 48.4 60.0 쑗쑗 1024 x 768 56.5 70.1 쑗 – 1024 x 768 57.7 72.0 쑗 – 1024 x 768 60.0 75.0 쑗 – 1024 x 768 68.7 85.0 쑗 –

NEC(PC9800) 640 x 400 24.8 56.4 쑗 –

640 x 400 31.5 70.1 쑗 –

640 x 480 31.5 60.0 쑗 –

640 x 480 37.5 75.0 쑗 –

800 x 600 37.9 60.3 쑗 –

800 x 600 46.9 75.0 쑗 – 1120 x 750 50.0 60.1 쑗 – 1024 x 768 56.5 70.1 쑗 – 1024 x 768 60.0 75.0 쑗 –

Apple Macintosh

640 x 480 35.0 66.7 쑗 –

(MAC 16") 832 x 624 49.7 74.5 쑗 – (MAC 19") 1024 x 768 60.2 74.9 쑗 – (MAC 21") 1152 x 870 68.7 75.1 쑗 – SUN 1152 x 900 61.8 66.0 쑗 – SGI 1024 x 768 49.7 60.4 쑗 –

1152 x 900 71.7 76.1 쑗 –

*Factory presets have been set to the standard signals for the

display resolution/frequency, but depending on the personal computer adjustment may be required.

* Proper display may not be possible for composite sync sig-

nals, sync-on-green sync signals, etc.

쑗 : Supported frequencies

–:Unsupported frequencies

Page 50

E – 50

Specifications

Model Name HE-3200 Display Method Single Chip Digital Micromirror Device (DMDTM) DMD Panel 0.7"

508,800 pixels (848⳯600)

Lens Manual zoom, Manual focus

F=3.0 – 3.3 f=21.5 – 25.8mm Lamp 130W High Performance Compact Lamp Image Size Min. 32" (Throw distance 1.2m / 3.9 feet : Tele) Max. 200" (Throw distance 6.4m / 20.9 feet : Wide) Color Reproduction Full color, 16.7 million colors simultaneously Light Output 450 ANSI lumens (normally white) Contrast Ratio 700:1 (Full on/off) Scanning Frequency Horizontal : 15 – 85 kHz

Ver tical : 50 – 85 Hz Functions Zoom (Manual), Focus (Manual), Projection angle, Source select (S-Video/Video/YCbCr/YPbPr/RGB/DVI),

Aspect, Standby On/Off, Projection orientation, Digital keystone correction, Brightness, Contrast, Color,

Tint, Sharpness, Color temperature, Gamma correction, RGB signal automatic position and phase adjustment Digital RGB Input T.M.D.S-compliant (single link only)

Input Terminal DVI-D 24 pin⳯1 RGB Signal VGA : 640⳯480 Throughput image / Magnified image

S-VGA : 800⳯600 Throughput image

XGA : 1024⳯768 Throughput image / Compressed image Analog RGB Input Separate signal system

Video signal Analog : 0.7Vp-p / 75Ω Sync signal Separate : TTL Level (Positive / Negative) Input Terminal RGB Mini D-Sub (15 pin) RGB Signal VGA : 640⳯480 Throughput image / Magnified image

S-VGA : 800⳯600 Throughput image

XGA : 1024⳯768 Throughput image / Compressed image Video Input Composite, S-Vide, Component (YCbCr)

Color System NTSC 3.58, NTSC 4.43, PAL, PAL N, PAL M, PAL60, SECAM Video signal Composite : 1.0Vp-p/75Ω

S-Video : Y (1.0Vp-p/75Ω), C (0.286Vp-p/75Ω)

Component : Y-signal (1.0Vp-p / 75Ω), Cb, Cr signal : 0.7Vp-p (75Ω)

Input Terminal Composite : RCA⳯1 (Shared with comonent-Y)

S-Video connector : Mini DIN 4 pin

Component : RCA⳯3 DVT Input Component (YPbPr)

Video signal Y signal : 1.0Vp-p / 75Ω, Pb, Pr signal : 0.7Vp-p / 75Ω Input Terminal RCA⳯3 (Shared with YCbCr)

DVT Input 480p, 576p, 720p, 1080i Horizontal Resolution NTSC : 400 lines or more Environment Operating temperature : 5 – 35°C / 41 – 95°F, 30 – 85% humidity (no-condensing)

Storage temperature : –10 – 60°C / 14 – 140°F, 10 – 85% humidity (no-condensing) Power Requirement 100 – 240V AC, 50 / 60Hz Input Current 2.0A Power Consumption 200 W (STANDBY 18W) Dimensions 235 (W)⳯91 (H)⳯198 (D) mm (not including protrusion)

9.3 (W)⳯3.6 (H)⳯7.8 (D) inch (not including protrusion)

Weight Approximately 2.0kg / 4.4 lbs Regulations UL Approved (UL 6500, CSA-E60065)

Meets FCC Class B requirements

Meets EMC Directive (EN55022, EN55024)

Meets Low Voltage Directive (EN60065)

The specifications are subject to change without notice.

Digital Micromirror DeviceTM (DMDTM) by Texas Instruments

Page 51

E – 51

Main Unit External View

DVI-D RGB

S-VIDEO

VIDEO

Pb/Cb

Pr/Cr

91 mm / 3.6 inch

235 mm / 9.3 inch

174 mm / 6.9 inch

198 mm / 7.8 inch