Plura SFP-H Hybrid Series, SFP-317-H, SFP-332-H, SFP-324-H, SFP-321-H Operating Instructions Manual
...
Operating
Instructions
SFP-H “Hybrid” Series
SFP-H Series
SFP-317-H
SFP-321-H
SFP-324-H
SFP-332-H
SFP-347-H
SFP-355-H
SFP-365-H
SFP-384-H
SFP-H SERIES
User’s Manual
2 of 50
PRECAUTION--------------------------------------------------------------------------------------------------6
1. OVERVIEW---------------------------------------------------------------------------------------------- 10
2. GENERAL FEATURES----------------------------------------------------------------------------------- 10
3. FUNCTIONS AND I/O DESCRIPTIONS --------------------------------------------------------------- 11
1) FRONT ----------------------------------------------------------------------------------------------- 11
SFP-317-H------------------------------------------------------------------------------------------ 11
Front Keypad--------------------------------------------------------------------------------------- 11
Front Keypad Operations ------------------------------------------------------------------------- 12
SFP Modules Information ------------------------------------------------------------------------- 13
Front panel LED Operations----------------------------------------------------------------------- 13
Speaker Out---------------------------------------------------------------------------------------- 13
2) REAR --------------------------------------------------------------------------------------------------- 14
I/O Details ----------------------------------------------------------------------------------------- 14
Power IN–AC & DC ------------------------------------------------------------------------------ 14
PIPM OPTION - Connectivity -------------------------------------------------------------------- 15
RJ-45 Connections--------------------------------------------------------------------------------- 16
I/O Description ------------------------------------------------------------------------------------ 16
4. MENU OVERVIEW ------------------------------------------------------------------------------------- 17
To display / hide the Menu ----------------------------------------------------------------------- 17
To go to the next level ---------------------------------------------------------------------------- 17
To go back to the previous level ----------------------------------------------------------------- 17
Typical Menu Operation--------------------------------------------------------------------------- 18
5. BASIC OPERATION ------------------------------------------------------------------------------------ 18
Turning ON & OFF the Monitor ------------------------------------------------------------------ 18
Volume Adjustment ------------------------------------------------------------------------------- 18
On Screen Menu Language Selection ------------------------------------------------------------ 18
6. ON SCREEN MENUS SELECTION AND ADJUSTMENT --------------------------------------------- 19
How to adjust the OSD screen ------------------------------------------------------------------- 19
7. SELECT VIDEO INPUT --------------------------------------------------------------------------------- 19
How to Select Video Source by OSD ------------------------------------------------------------- 19
SFP-H SERIES
User’s Manual
3 of 50
8. MENU OPTIONS FOR DIFFERENT I/P SOURCES ---------------------------------------------------- 20
Menu of different Input source ------------------------------------------------------------------- 20
Adjust ---------------------------------------------------------------------------------------------- 21
Color Temperature Control------------------------------------------------------------------------ 21
SCAN ----------------------------------------------------------------------------------------------- 21
Aspect Ratio --------------------------------------------------------------------------------------- 22
Zoom----------------------------------------------------------------------------------------------- 22
Mono/Blue Only ----------------------------------------------------------------------------------- 23
PC Menu (pc mode only) ------------------------------------------------------------------------- 23
Flip ------------------------------------------------------------------------------------------------- 23
NR (Noise Reduction) ----------------------------------------------------------------------------- 24
SFP Setting----------------------------------------------------------------------------------------- 24
9. AUDIO MENU OPTIONS ------------------------------------------------------------------------------ 25
MAIN / SUB Audio out ---------------------------------------------------------------------------- 25
SDI Main/ SDI Sub Audio Output Channel ------------------------------------------------------ 25
SDI Main/ SDI Sub Audio Group ----------------------------------------------------------------- 25
Level Meter ---------------------------------------------------------------------------------------- 25
Level Meter Type ---------------------------------------------------------------------------------- 26
Level Meter Position ------------------------------------------------------------------------------- 26
Level Meter Scale ---------------------------------------------------------------------------------- 26
Audio Loudness (LKFS) ---------------------------------------------------------------------------- 27
Volume --------------------------------------------------------------------------------------------- 27
Lip Sync Delay ------------------------------------------------------------------------------------- 27
10. MARKER MENU OPTIONS-------------------------------------------------------------------------- 28
Marker & User Marker ---------------------------------------------------------------------------- 28
Safety Area----------------------------------------------------------------------------------------- 28
Center Maker -------------------------------------------------------------------------------------- 29
Marker Width -------------------------------------------------------------------------------------- 29
Marker Color--------------------------------------------------------------------------------------- 29
Preset1 & Preset2 --------------------------------------------------------------------------------- 29
11. GPI MENU OPTIONS -------------------------------------------------------------------------------- 30
GPI Control & GPI#-------------------------------------------------------------------------------- 30
SFP-H SERIES
User’s Manual
4 of 50
12. SETUP MENU OPTIONS ---------------------------------------------------------------------------- 31
Setup Load & Setup Save------------------------------------------------------------------------- 31
Function 1 & Function 2 & Function 3 ----------------------------------------------------------- 31
On Screen Display --------------------------------------------------------------------------------- 32
OSD Option---------------------------------------------------------------------------------------- 32
Time code------------------------------------------------------------------------------------------ 33
Under Monitor Display (color: Tally R/G mode action ) ----------------------------------------- 33
Input ID -------------------------------------------------------------------------------------------- 33
SDI Signal state ------------------------------------------------------------------------------------ 34
Advanced ------------------------------------------------------------------------------------------ 34
Information ---------------------------------------------------------------------------------------- 34
Control --------------------------------------------------------------------------------------------- 34
Screen Saver --------------------------------------------------------------------------------------- 35
Screen Control ------------------------------------------------------------------------------------- 35
Fan Control ---------------------------------------------------------------------------------------- 35
Network Configuration ---------------------------------------------------------------------------- 36
X768 Mode ---------------------------------------------------------------------------------------- 36
Caption--------------------------------------------------------------------------------------------- 36
Waveform Format (SDI ONLY) -------------------------------------------------------------------- 37
Y-Pb-Pr Waveform--------------------------------------------------------------------------------- 37
Y-Waveform + Vector Scope---------------------------------------------------------------------- 37
Double --------------------------------------------------------------------------------------------- 38
Y-Waveform + Vector Scope Trans --------------------------------------------------------------- 38
Vector Color --------------------------------------------------------------------------------------- 38
Line Select ----------------------------------------------------------------------------------------- 38
Line # ---------------------------------------------------------------------------------------------- 39
Line Display ---------------------------------------------------------------------------------------- 39
Dual Link Mode (SDI only) ------------------------------------------------------------------------ 39
Set ID & Active Set ID ---------------------------------------------------------------------------- 39
13. PIP (PICTURE IN PICTURE) ------------------------------------------------------------------------- 39
PIP ON/OFF ---------------------------------------------------------------------------------------- 39
Input Source --------------------------------------------------------------------------------------- 39
Aspect Ratio --------------------------------------------------------------------------------------- 40
SFP-H SERIES
User’s Manual
5 of 50
Position--------------------------------------------------------------------------------------------- 40
PIP Blend------------------------------------------------------------------------------------------- 41
PIP Swap ------------------------------------------------------------------------------------------- 41
Audio Select --------------------------------------------------------------------------------------- 41
Sub Window Function ----------------------------------------------------------------------------- 41
14. OSD TREE -------------------------------------------------------------------------------------------- 43
1) PICTURE ------------------------------------------------------------------------------------------------ 44
2) SOUND------------------------------------------------------------------------------------------------- 45
3) MARKER------------------------------------------------------------------------------------------------ 46
4) GPI ---------------------------------------------------------------------------------------------------- 47
5) SETUP -------------------------------------------------------------------------------------------------- 48
6) PIP ---------------------------------------------------------------------------------------------------- 49
SFP-H SERIES
User’s Manual
6 of 50
Precaution
Before operating the set, please read this manual carefully.
WARNING:
To reduce the risk of any electric shock, do not remove back cover as there are no user serviceable
parts inside. Please refer to Plura or a qualified service personnel/agent. To prevent fire or shock
hazard, do not expose the rear side of the unit to rain or moisture. Do not rub or clean the Active Matrix
LCD with any harsh surface as this may scratch, mark, or damage the Active Matrix LCD permanently.
CAUTION:
Unauthorized tampering with the inside of the monitor voids the warranty.
The manufacturer shall not warrant for any damage caused by improper maintenance and/or repair by any
third party.
Important safeguards for you and your new product:
Please read and observe the following safety points when installing and using your new device an
d save them for future reference.
1. Read Instructions
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
SFP-H SERIES
User’s Manual
7 of 50
The safety and operating instructions should be retained for future reference.
4. Observe Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Disconnect the unit from the mains before cleaning. Do not use abrasive cleaners. Use a damp
cloth for cleaning.
6. Water and Moisture
Do not use this unit near water.
7. Transportation
A product should be transported with care. Excessive force and uneven surfaces may cause the
damage to product.
8. Attachments
Do not use attachments not recommended by Plura as they may cause hazards.
9. Ventilation
Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s instructions.
10. Power Sources
This product should be operated only from the type of power source indicated on the marking
label. If you are not sure of the type of power supply, consult your power company.
11. Power Lead Polarization
This product is equipped with a three-wire grounding-type cord. This is a safety feature. Do not
use an alternative power cord.
12. Power Cord Protection
Power-supply cords should be protected so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to cords at plugs, convenience
SFP-H SERIES
User’s Manual
8 of 50
receptacles and the point where they exit from the product.
13. Outdoor Cable Grounding
If an outdoor cable is connected to the product, be sure the cable is grounded to provide some
protection against voltage surges and built-up static charges. A“face plate”also needs to be
installed with an isolating capacitor to prevent any damage from static.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet. This will prevent possible damage
to the product due to lightning and power-line surges.
15. Earthing the product
This product must be earthed properly to comply with the safety regulations in the country of use.
If you are unsure of these regulations, please consult a qualified electrician.
16. Servicing
Do not attempt to service this product yourself as opening or removing covers may ex pose you to
dangerous voltages or other hazards. Refer all servicing to qualified service personnel. If the
device does not operate properly, switch it off and call your dealer.
17. Service
Turn this product off, unplug from the mains supply and refer servicing to qualified service
personnel under the following conditions:
A. If the power-supply cord or plug is damaged.
B. If the LCD has been damaged.
C. If water or moisture penetrated the glass and/or the LCD screen.
D. If the product does not operate normally by following the operating instructions. Adjust only
those controls that are covered by the operating instructions as an improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
E. If the product has been dropped or the frame has been damaged.
F. If the product exhibits a distinct change in performance.
SFP-H SERIES
User’s Manual
9 of 50
18. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform s
afety checks to determine that the product is in proper operating con dition and the front seal is int
act
.
19. Mounting
The product should be mounted on a wall only as recommended in the instructions.
20. Power
This device operates on an AC supply; the voltage is as indicated on the label on the Manual.
This device must be earthed at all times through the chassis as well as through the power lead.
SFP-H SERIES
User’s Manual
10 of 50
1. OVERVIEW
SFP-H is the NEW FUTURE PROOF Hybrid Monitor Series, supporting Coax, Fiber & IP connectivity.
The SFP-H monitor series will be available in multiple sizes starting from 17” all the way to 84”.
The SFP-H is integrated with powerful H/W & S/W platforms to support Coaxial 3Gb/s BNC I/O
connectivity, Coaxial SFP I/O connectivity, IP SFP+ over Fiber decoding "ST-2110 & ST-2022" with ThirdParty H/W decoder and the NEW PIPM "Plura Software Stack IP Platform" decoder.
SFP-H is the ONLY monitor series in the market that can decode ST-2110, ST-2022 and ASPEN IP streams
with PIPM "Plura Software Stack IP Platform" based on a powerful computing core and utilizing standard
10G/s SFP+ module.
2. GENERAL FEATURES
The New FUTURE PROOF SFP-H, Hybrid Monitor Series, supporting Coax, Fiber & IP connectivity
Decode ST-2110, ST-2022 and ASPEN IP streams with "PIPM" Plura Software Stack IP Platform
module
Supports Coaxial 3Gb/s BNC I/O connectivity
Supports Coaxial SFP I/O connectivity
Supports IP SFP+ over fiber decoding "ST-2110 & ST-2022" with any Third-Party H/W decoder
2 x SFP+ cages supporting 10G/3G/1.5G SDI
1 x 3G/1.5G Input port
2 x 3G/1.5G output ports
LKFS Audio Loudness logging & measurement
*“PIPM” Plura Software Stack IP Platform - OPTIONAL
Built-IN 4 x 4 Crosspoint Solution
1 x HDMI, 1 x DVI & other legacy I/O
178 degree Viewing Angle Display
Gamma Selectable ( 0.8 - 3.0)
Color Temperature - User, VAR, Adjustable (11000K TO 3200K)
(ICAC) - Plura Intelligent Connection for Alignment & Calibration
Display Advanced Waveform & Vector Scope simultaneously with line select
Various and User defined Markers Display & Safe Area
Programmable 3 User Front Pushbutton Controls & GPI
Closed Caption (608/708) - North American Market
Cutting edge De-interlacing and scaling Technology
Fast Response Time for high motion video
Internal Monitor Display (IMD)
Ethernet & RS232 Remote Control
Underscan / Overscan / Normal / Zoom
Pixel to Pixel Mode, Tally, DC operation only “SFP-317-H & SFP-321-H”
False Color and Peaking Filter / Focus Assist
Video Range test with adjustable Y & C values
Display LTC & DIVTC time code with line select
Embedded Audio input, Digital Audio Decoding
Internal Pattern Generator and Wall Control System
Auto Calibration: Spyder Elite / CA-210 & CA-310(Minolta) / K-10(Klein) / Jetti
SFP-H SERIES
User’s Manual
11 of 50
3. Functions and I/O descriptions
1) Front
SFP-317-H
Front Keypad
Headphone
LED
Front Key
Speaker
USB-PIPM
SFP-H SERIES
User’s Manual
12 of 50
Front Keypad Operations
Key Name
Operation
STANDBY
►Power ON/OFF Button. This button is operated after being pressed about 3 seconds.
INPUT
SFP1/SFP2/SDI/PIPM
►SFP Modules Input CH selected.
►Channels in the input signal, the key led light.
OUTPUT
SFP1/SFP2/SDI/AUX/
MAIN/SUB
►SFP Modules Output CH selected.
ALL
►SFP Modules ALL Output CH selected.
FUNCTION
F1/F2/F3
►Executes functions of user selected.
UNDEF, Aspect, Mono/Blue only, Audio Channel, Safety area marker, Time code,
Analog Caption, Audio mute, Still image, Zoom, Flip, Gamma select, PIP func & Input,
Sub win full, Sub win part
SEL/INPUT
► Activates OSD menu of input source selecting.
► Changes input source by selecting.
► Executes functions (by OSD help commands) in main OSD menu.
►Activates child menu.
MENU
► Activates main OSD menu.
► Navigates higher menu in main OSD menu.
► Exits OSD menu.
Adjust
►Adjust Picture Menu(Brightness -> Contrast -> Color -> Sharpness->Phase & Tint)
►Turn Right (with „UP' button is same)
►Turn Left (with „DOWN' button is same)
SFP-H SERIES
User’s Manual
13 of 50
SFP Modules Information
SFP1/SFP2: SFP Module information will
be displayed when available.
The selected output channel will be in
Yellow.
SFP1/SFP2/SDI/PIPM: Available input
channels.
SFP1/SFP2/SDI/Aux/SDI Main/SDI Sub:
can be selected as output port.
Front panel LED Operations
Green LED ON when Function Key and Power On
RED LED ON in standby mode
Speaker Out
Interface
Description
Speaker R/L out
8 ohm±15%, Max 3W + 3W
SFP-H SERIES
User’s Manual
14 of 50
2) Rear
I/O Details
Power IN – AC & DC
*DC is not applicable when using PIPM
PIN NO
Description
1 , 2
GND
3 , 4
+ 12V
1
2
3
4
SFP-H SERIES
User’s Manual
15 of 50
PIPM OPTION - Connectivity
PIPM In
OPS 8p Connector
SFP-H SERIES
User’s Manual
16 of 50
RJ-45 Connections
- Firmware Upgrade/ System Controller (Ethernet) & GPI
Remote PIN Assignment
GPI 7 PORT
(STAND BY/POWER ON/OFF)
I/O Description
Interface
Description
SFP Module
2 Slot
Input CH 1
Output CH 1
Input CH 2
Output CH 2
SDI
Input
Output
AUX
Output
RS-232 IN
Update/Multi Control/Auto color calibration
HDMI
High Definition Multimedia Input
DVI-I
DVI-I Type Digital / Analog PC-RGB Video Input
Control Terminal: 1 ~ 7 Pin
GND Terminal: 8 Pin of RJ-45
Contact Point Switch
It is possible to attach
pin one by one.
GPI
ETHERNET/UPDATE
8 PIN COMMON(GND) 4 PIN GPI 4 PORT
7 PIN
6 PIN GPI 6 PORT 2 PIN GPI 2 PORT
5 PIN GPI 5 PORT 1 PIN GPI 1 PORT
3 PIN GPI 3 PORT
SFP-H SERIES
User’s Manual
17 of 50
High Definition Multimedia Input Compatible
CVBS1/Pr/R In
GBR (SOG sync) Input
Y, Pb, Pr Component Video Input
CVBS / Composite/S-Video Input
CVBS2/Y/G/Y In
CVBS3/Pb/B/C In
CVBS1/Pr/R Out
Component/GBR/Composite1,2,3/ S-Video Loop Out
CVBS2/Y/G/Y Out
CVBS3/Pb/B/C Out
AUDIO R In
DVI-I/Component/GBR/Composite1,2,3/S-Video
Sound Input
AUDIO L In
AUDIO R Out
AUDIO MONITOR OUT
AUDIO L Out
AC IN
AC90V ~ 240V, 50Hz/60Hz
DC IN
PBM-217: DC 11V ~ 17V ,PBM-224: DC 24V
ETHERNET UPDATE
ETHERNET/Firmware Upgrade
GPI
GPI 1 ~ 7 Control Port
4. MENU OVERVIEW
In this menu system, there are several ways to customize the menu settings.
Most menus consist of three levels to select the correct option/s, but some require greater depth for
variety of settings. If you press the MENU button, only the first and second level of the menu system will
appear on the monitor screen. The third level can be displayed by pressing SEL/INPUT. If a menu has
more than three levels, the pop-up dialogue box will be displayed as the fourth or fifth level.
To display / hide the Menu
Press the MENU button to display the menu. To exit the menu, press the MENU button
second time.
To go to the next level
Press SEL/INPUT button.
To go back to the previous level
Press MENU button
SFP-H SERIES
User’s Manual
18 of 50
Typical Menu Operation
1. Press MENU button: The main menu will be displayed.
2. Use Adjust / Take button Turn Right/ Left to select the desired menu option (icon).
3. While the desired menu option is selected, press SEL/INPUT to move to the second level.
4. Use Adjust / Take button Turn Right/ Left to select the second menu option.
5. Press SEL/INPUT to move to the third level: Some menu options require additional steps.
6. Press MENU to return to the previous menu to return to monitor viewing.
5. BASIC OPERATION
Turning ON & OFF the Monitor
1. First and foremost connect the power cord correctly. The monitor will be in standby or power
ON mode. If the monitor is In standby mode, in order to turn monitor ON, press and hold the
Standby button for at least 3 seconds.
2. Select the input source by using SEL/INPUT button on Keypad in front of monitor.
3. To turn the monitor OFF, press and hold the Standby button for at least 3 seconds.
Volume Adjustment
1. Press the Adjust / Take button Turn Right/ Left button on Keypad.
2. If you want to turn the sound off, press the FUNCTION (Audio mute) button.
3. You can cancel this function by pressing the FUNCTION (Audio mute) or volume control
button.
On Screen Menu Language Selection
- SETUP -> On Screen Display -> OSD Option -> Language
- The menu can be shown on the screen in the selected
languages.
- Supported Languages: English, Spanish, Portuguese, German,
French and Italian
SFP-H SERIES
User’s Manual
19 of 50
6. On Screen Menus Selection and Adjustment
How to adjust the OSD screen
1. Press the MENU button and then UP/DOWN button to select each menu.
2. Press the SEL/INPUT button and then use UP/DOWN (SEL/INPUT)/MENU button to
display the available menu.
*Some monitors OSD (On Screen Display) may differ slightly from what is shown in this manual.
7. SELECT VIDEO INPUT
How to Select Video Source by OSD
1. Press the SET/INPUT button and then UP/DOWN button to select the desired video source.
2. Press the SET/INPUT button to go to desired video source.
3. If Input Name is enabled, The SET/INPUT button will display input name as enetered in edit
mode.
SFP-H SERIES
User’s Manual
20 of 50
8. MENU OPTIONS FOR DIFFERENT I/P SOURCES
Menu of different Input source
< Video (NTSC) menu> < PC menu> < SDI, HDMI menu>
SFP-H SERIES
User’s Manual
21 of 50
Adjust
- Adjust the values of Brightness, Contrast, Color, Tint and
Sharpness directly from -50 to 50
Contrast, Brightness, Sharpness, Color (All Sources), Tint N/A (PC,
DVI, HDMI, Component), Phase (Component).
Color Temperature Control
- For Setting the Color temperature or adjusting RGB gain value.
- User (User setting RGB gain value), VAR(3200K ~ 11000K), Often used value (11000K, 9300K, 6500K,
5400K, 3200K)
SCAN
1. Over Scan – 95% input size and fit the selected display
resolution.
2. Zero Scan – 100% input size and fit the selected display
resolution.
3. Under Scan – 105% Input size and fit the selected display
resolution.
3. Pixel to Pixel – Displays the exact input resolution regardless of
the panel resolution.
User’s Manual
Aspect Ratio
- For setting the aspect ratio.
- Full Screen: The images are displayed to the full panel resolution.
- Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1: The images are displayed to the selected aspect ratio.
- AFD function Added
- PC mode: Full Screen & 4:3 only
Zoom
- Zoom picture by (2X, 3X, 4X, 5X) ratio.
- If user selects the Zoom 3X option, the monitor will divide the
image into 3x3=9 portions and the monitor will display the yellow
box in picture as shown below.
- Press Select or Enter button, user can see the enlarged picture of
the selected portion.
- Pressing Menu key will exit the zoom mode.
- Example (3X3)
Zoom X position: Coordinate of video image’s H position.
Zoom Y position: Coordinate of video image’s V position.
SFP-H SERIES
User’s Manual
22 of 50
- Zoom picture by (2X, 3X, 4X, 5X) ratio.
- If user selects the Zoom 3X option, the monitor will divide the
image into 3x3=9 portions and the monitor will display the yellow
box in picture as shown below.
- Press Select or Enter button, user can see the enlarged picture of
the selected portion.
- Pressing Menu key will exit the zoom mode.
SFP-H SERIES
22 of 50
User’s Manual
Mono/Blue Only
- Mono color: For selecting monochrome images.
- Blue Only: IN blue ONYr
PC Menu (pc mode only)
- PC input mode ONLY
- Select Auto-adjust to adjust Phase, HV position, Frequency
- Auto-Adjust automatically set the optimum values of Phase, HV position and Frequency.
Flip
-H-Flip Display ON/OFF
< H-Flip Off >
SFP-H SERIES
User’s Manual
23 of 50
- Mono color: For selecting monochrome images.
- Blue Only: IN blue ONYr
< H-Flip On >
SFP-H SERIES
23 of 50
SFP-H SERIES
User’s Manual
24 of 50
NR (Noise Reduction)
-Noise Reduction on/off. (NR is for Video signal (HD-SDI, Composite, S-Video and Y.Pb.Pr) & DTV timing.
SFP Setting
- SFP 1/ SFP 2 / SDI / AUX / SDI Main / SDI Sub available Output ports.
- SFP 1/ SFP 2 / SDI / PIPM available Input ports.
SFP-H SERIES
User’s Manual
25 of 50
9. AUDIO MENU OPTIONS
MAIN / SUB Audio out
-Main: Select Internal Speaker out. (Auto/SDI1/SDI2/HDMI/Line in)
-Sub: Select sub display sound. (Auto/SDI1/SDI2/HDMI/Line in)
SDI Main/ SDI Sub Audio Output Channel
- Audio output channel source select. (Channel1~4, Channel1/2, Channel3/4, off)
SDI Main/ SDI Sub Audio Group
- Select primary or secondary audio group. (Group 1~4)
Level Meter
- Display the audio level meter on screen with SDI input.
- Audio level meter will NOT be display when OSD is ON.
SFP-H SERIES
User’s Manual
26 of 50
Level Meter Type
-Pair: Displays Right and Left Channels in pairs
-Group: Displays Right and Left Channels in groups
Level Meter Position
- Level Meter Position selection. (TOP/Middle/Bottom)
Level Meter Scale
- Level Meter Scale mode selection
(SMPTE Digital/EBU Digital/SMPTE IRT/EBU IRT/Nordic/
BBC/EBU/DIN/Expander DIN/SMPTE VU/EBU VU/France
VU)
SFP-H SERIES
User’s Manual
27 of 50
Audio Loudness (LKFS)
-Audio Loudness setting (Off, Normal, Transparent) and Set Target levels (LKFS)
Volume
- Adjust the speaker or headphone Volume level. (0~32)
Lip Sync Delay
- Lip sync delay: Off, 1 Frame, 2 Frame
SFP-H SERIES
User’s Manual
28 of 50
10. Marker MENU OPTIONS
Marker & User Marker
1. Marker : 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1&4:3, User1, User2, User3 fitted panel
size marker on screen.
2. User Marker: The user wants Marker size setting. (Below panel size)
Example (1440x900 panel)
16:9 (16:9 Marker) 16:9 (4:3 Marker)
Safety Area
-Safety Area: Draw dotted line Marker on screen.
-16:9 95/93/90/88/80%
-4:3 95/93/90/88/80%
-EBU Action 16:9/14:9/4:3
-EBU Graphic 16:9/14:9/4:3
< Marker >
< User Marker >
SFP-H SERIES
User’s Manual
29 of 50
Center Maker
- “+” Marker on center of screen
Marker Width
-Marker line thickness setting. (0~10)
Marker Color
- Marker Line Color: Select Marker line color (White,
Yellow, Blue, RED, Black)
- Safety Line Color: Select Safety line color (White,
Yellow, Blue, RED, Black)
- Marker Back Color: Select Marker Back Color. (None,
Gray, White, Blue, Black)
- Safety Back Color: Select Safety Back Color. (None,
Gray, White, Blue, Black)
- Marker BK Blend Color: Select Marker blending level.
(0 ~ 5)
- Safety BK Blend Color: Select Safety blending level.
(0 ~ 5)
Preset1 & Preset2
- For setting the marker to use by GPI controller.
- GPI preset markers are only worked by GPI controller
SFP-H SERIES
User’s Manual
30 of 50
11. GPI MENU OPTIONS
GPI Control & GPI#
- For allocating functions to particular GPI pins.
- When remote control operations are to be performed using the GPI Controller.
- GPI Control: GPI function Enable/Disable
- GPI 1 ~ 7
GPI Function
Description
UNDEF
Not set (no function allocated)
Marker1 On/Off, Marker2 On/Off
Displays the markers which have been set by the
GPI PRESET1, 2 items on the screen.
Center Marker
Displays the center marker.
Safety Area
Displays the Safety Area.
Tally R, Tally G
For lighting up the Red or Green tally LED.
Scan
Over Scan/Zero Scan/Under Scan/ Pixel to Pixel
Input Composite1, Input R.G.B., Input SDI Main,
Input SDI Sub, Input Y.Pb.Pr , Input PC ,
Input DVI, Input HDMI
Switches the input source.
Menu Key, Enter Key, Up Key, Down Key
Left Key, Right Key
Use the key function by GPI.
Function 1, Function 2, Function 3
Activates FUNCTION 1, 2, 3 buttons
Aspect
Sets the aspect ratio of the images
Waveform
Activates WAVRFORM & Vector Scope (SDI Only)
GPI 7 : Power Key(Fixed)
SFP-H SERIES
User’s Manual
31 of 50
12. SETUP MENU OPTIONS
Setup Load & Setup Save
- Setup Load: Load user saved values or default value
- Setup Save: Save user setting values at user 1, 2, 3.
Function 1 & Function 2 & Function 3
- Function 1, 2, 3: Select the function to be allocated to the FUNCTION 1, 2, 3 buttons
Function1~6 button
Description
UNDEF
Not set (no function allocated)
Waveform
Display the Waveform
Level meter
Audio LV Meter On / Off
Audio Loudness
Audio Loudness(LKFS) On / Off
H/V delay
H delay, V delay, HV delay, Off
SDI Main/SDI Sub/Analog
Select SDI Main/SDI Sub/Analog source
Scan
Over Scan/Zero Scan/Under Scan/Pixel to Pixel
Aspect
Turn ON / OFF Aspect Ratio
Mono/Blue Only
Execute Mono color or Blue Only
Audio Group
Select the embedded audio Group in SDI input.
Audio Channel
Select the embedded audio channel in SDI input.
SFP-H SERIES
User’s Manual
32 of 50
Marker size
Select Marker size
Safety Area Marker
Select Safety Area
Time Code
Time Code Display
Caption
Closed Caption On/Off
Audio Mute
Toggles Audio speaker/headphone Mute .
Still Image
Still Image On/Off
Flip
H-Flip Display ON/OFF
Gamma Select
Gamma Level Select (0.8 ~ 3.0)
Vector Color
Select 100% or 75%
I/P Mode
Line Doubler / Inter-Field / Field Merge
Marker Preset 1/2
Displays the markers which have been set by the PRESET1, 2 items
on the screen.
WFM Line Select
WFM Line Select On/Off
PIP Func & Input
PIP func & input Select
Sub Win Full
Display the same full images on POP1 screen
Sub Win Part
Scale first image to 4:3 aspect ratio and then display on POP2 screen
On Screen Display
OSD Option
Language: Select a language for the menus to appear in.
(English, Spanish, Portuguese, German, French, Italian)
OSD Position: L-T, R-T, C, L-B, R-B
OSD Transparency: Disable blending OSD background with video image.
OSD Time out: OSD gone time setting. (3~200)
SFP-H SERIES
User’s Manual
33 of 50
Time code
Time code Enable: Time code Display (off/VITC/ATC LTC/ATC VITC1/ATC VITC2)
Time code size: Time code size selection. (Small, Middle, Large)
Time code Position: Time code display position selection (L-T, C-T, R-T, L-B, C-B, R-B)
Time code Transparency: Disable blending Timecode background with video image. (0%, 25%,
50%, 75%, 100%)
VITC Line : Auto, Line 1~31
Under Monitor Display (color: Tally R/G mode action )
UMD: UMD display on/off
UMD Character: UMD Character Select
UMD Position: UMD display position selection (L-T, C-T, R-T, L-B, C-B, R-B)
UMD FG Color: UMD Character color Select (RGB_255_192_128_Transparent)
UMD BG Color: UMD BG color Select (RGB_255_192_128_ Transparent)
Input ID
Input ID: source Message display.
Message OSD
SDI1 1920 x 1080i 60Hz
Info Message
00:00:00:00
Timecode
L-T
C-T
R-T
L-B
C-B
R-B
UMD
Channel-12
Tally Green
Channel-12
Tally Red
Channel-12
SFP-H SERIES
User’s Manual
34 of 50
ID Style: select “Input Format”/”Custom Label”
Input Label: Display user custom name instead of standard input source ID on source OSD and
message OSD
SDI Signal state
SDI Signal date display on/off (H/V sync, image, Audio, Audio Phase, EDH packet, EDH FF CRC,
EDH APCRC, SAC, EAV, VPI)
Advanced
- Information, Control, Screen Saver, Screen Control, Fan
Control, x768 Mode
Information
- Version, Release day, Release time, operating time, FPGA
Version, Calibration ID
Control
- FRONT LED: Front LED on/off
- Local Enable: Power, up and down keys are active ONLY,
if Local enable is off.
- Remote Enable: Select local or remote control. If remote
control is ON, both local (front keypad) and remote are
active. However when local is ON, ONLY local control is
enabled.
- Auto Key Lock: The front Keypad automatically locks for
any non activities after 10 minutes. To unlock, press and
hold any Key button for about 2 seconds.
SFP-H SERIES
User’s Manual
35 of 50
Screen Saver
- Blue Screen: Enables screen saver functions if necessary.
- BG Gray: Select gray level for outside video boundary
- Power save Mode: DPMS (Display Power Management Signaling)
Power Save Mode
Screen Control
-Reset Calibration
Color Calibration Reset
-Backlight Adjust
Inverter dimming Level select (0~100)
-Gamma Select
Gamma Level Select (0.8 ~ 3.0)
-I/P Mode
Line Doubler/inter-Field/Field Merge function on/off
-Dithering
Dithering function on/off
- Internal Pattern:
100% Color Bars, 75% Color Bars, Luma, RGB, White, Black, RED, Blue, Green
Fan Control
Fan Control: Internal Fan with temperature sensor Control, Auto / force on / force off
Fan Active Temperature: Adjusts fan temperature in Celsius degree. ONLY available when the
Fan Control set to Auto.
Hysteresis: Adjusts fan hysteresis temperature in Celsius degree. (1~10℃)
Shutdown: For a monitor protection, if the inside temperature reaches 75℃, the monitor will
shut its self down.
MCU Fan Control: Control main MCU Fan On/Off
SFP-H SERIES
User’s Manual
36 of 50
Network Configuration
-Plura System Controller (PSC-400/500) Network setting.
Load Network Settings: select “Enter”. (IP Address/Gateway/Subnet Load)
DHCP: DHCP on/off (Manual IP settings – DHCP on) and Select “Apply” .
X768 Mode
-Selects X768 native PC video timings. (Auto/1024x/1280x/1360x/1366x)
Caption
Closed Caption: 608 Line21, 608 ANC, 608 Trans-coded mode Select
ABCDEFGH
SFP-H SERIES
User’s Manual
37 of 50
- 608 Caption mode Select. (C/C1, C/C2, C/C3, C/C4, TEXT1, TEXT2, TEXT3, TEXT4, OFF)
Waveform Format (SDI ONLY)
Press the WAVEFORM button to display the WAVEFORM Mode
Y-Pb-Pr Waveform
- Y_Pb_Pr WAVEFORM, Audio Level Meter, Video Info status & Time code Display.
Y-Waveform + Vector Scope
- WAVEFORM & Vector Scope, Audio Level Meter, Video Info status & Time code Display.
SFP-H SERIES
User’s Manual
38 of 50
Double
- SDI 1, 2 & WAVEFORM & Vector Scope & Audio Level Meter, Video Info status & Time code
Display.
Y-Waveform + Vector Scope Trans
- WAVEFORM & Vector Scope Trans.
Vector Color
- Vector color: Select 100% or 75%
Line Select
- Select line WAVEFORM & Vector Scope display.
- Line select: 1~540
SFP-H SERIES
User’s Manual
39 of 50
Line #
-line select
Line Display
-off/on/5 sec
Dual Link Mode (SDI only)
-Dual Link Mode select. (Auto/Off/RGB444/YCbCr444/YCbCr422/Progressive)
Set ID & Active Set ID
- Set ID is required for remote control. Set ID range (01~99).
- Set Active SET ID number to enable Remote control.
- Active SET ID is the total number of monitors you are
planning to control.
13. PIP (Picture In Picture)
- Display two programs or sources at the same time. And set up PIP size and position.
PIP ON/OFF
- Control PIP function On/Off.
Input Source
- PIP input source verity of selections.
- Analog (Composite1, 2, 3, Y.Pb.Pr, GBR, PC) inputs + Digital (DVI, HDMI) + SDI (SDI1, SDI2)
inputs
-SDI + SDI input PIP
Ex) AV + S-Video (X), DVI + SDI (O), PC + DVI (O), SDI1+SDI2 (O)
SFP-H SERIES
User’s Manual
40 of 50
Aspect Ratio
- Choose PIP size
Position
- Choose the PIP position
PIP Small
PIP1
POP2
User’s Manual
PIP Blend
-Blend setting
PIP Swap
- Using Swap option, you can swap the program or source.
Audio Select
- Using Audio Swap option, you can swap the audio of the program or source.
Sub Window Function
- Full Sub Window: Display the same full image on POP1 screen.
SFP-H SERIES
User’s Manual
41 of 50
SFP-H SERIES
41 of 50
SFP-H SERIES
User’s Manual
42 of 50
- Part Sub Window: images are scaled to fit the screen in half.
- FULL, Part function is only available with Digital input (SDI1, SDI2, DVI, HDMI)
Sub Window Full
Sub Window Part
User’s Manual
14. OSD TREE
SFP-H SERIES
User’s Manual
43 of 50
SFP-H SERIES
43 of 50
User’s Manual
1) Picture
SFP-H SERIES
User’s Manual
44 of 50
SFP-H SERIES
44 of 50
User’s Manual
2) Sound
SFP-H SERIES
User’s Manual
45 of 50
SFP-H SERIES
45 of 50
User’s Manual
3) Marker
SFP-H SERIES
User’s Manual
46 of 50
SFP-H SERIES
46 of 50
User’s Manual
4) GPI
SFP-H SERIES
User’s Manual
47 of 50
SFP-H SERIES
47 of 50
User’s Manual
5) Setup
SFP-H SERIES
User’s Manual
48 of 50
SFP-H SERIES
48 of 50
User’s Manual
6) PIP
SFP-H SERIES
User’s Manual
49 of 50
SFP-H SERIES
49 of 50
www.plurainc.com
www.plurasfp.com
U.S.A. . Germany . U.A.E. . S.Korea . Mexico
Loading...