Plura PRM-217-3G,PRM-224-3G-0 Users Guide

Operating Instructions

P RM-3G

"LED & INTEGRTAED OLED" 3G Series

PRM-217-3G

PRM-2 17-3G
PRM-224-3G-O

Re-imagine Beyond Technology [e-mail]

Table of Contents

Operating Instructions

PRM-3G SERIES

2

PREACUTION--------------------------------------------------------------------------------------------------6

1. OVERVIEW------------------------------------------------------------------------------------------------9

2. GENERAL FEATURES-------------------------------------------------------------------------------------9

3. FUNCTIONAL EXPLANATION OF EACH PART ------------------------------------------------------ 11

1) FRONT PANEL------------------------------------------------------------------------------------------- 11

 PRM-224-3G-O ------------------------------------------------------------------------------------ 11

 Front Keys Arrangements ------------------------------------------------------------------------- 11

 Front Keys Operations----------------------------------------------------------------------------- 12

 Front panel LED Operations----------------------------------------------------------------------- 12

 Speaker Out----------------------------------------------------------------------------------------

2) REAR PANEL -------------------------------------------------------------------------------------------- 13

12

 Connection Details -------------------------------------------------------------------------------- 13

 Power IN ------------------------------------------------------------------------------------------- 13

 RJ-45 ----------------------------------------------------------------------------------------------- 13

 Interface description------------------------------------------------------------------------------- 14

4. MENU OVERVIEW ------------------------------------------------------------------------------------- 15

1. TO SHOW AND REMOVE THE MENU ---------------------------------------------------------------------- 15

2. TO GO TO THE NEXT LEVEL------------------------------------------------------------------------------- 15

3. TO GO BACK TO THE PREVIOUS LEVEL --------------------------------------------------------------------- 15

4. TYPICAL MENU OPERATION------------------------------------------------------------------------------ 15

5. BASIC OPERATION ------------------------------------------------------------------------------------ 15

1. TURNING ON THE MONITOR----------------------------------------------------------------------------- 15

2. VOLUME ADJUSTMENT ---------------------------------------------------------------------------------- 16

3. ON SCREEN MENU LANGUAGE SELECTION---------------------------------------------------------------- 16

6. ON SCREEN MENUS SELECTION AND ADJUSTMENT --------------------------------------------- 16

7. SELECT VIDEO INPUT --------------------------------------------------------------------------------- 17

8. VIDEO MENU OPTIONS ------------------------------------------------------------------------------ 18

Re-imagine Beyond Technology [e-mail]

1. HOW TO ADJUST THE OSD SCREEN ---------------------------------------------------------------------- 16

1. HOW TO SELECT VIDEO SOURCE BY OSD----------------------------------------------------------------- 17

1) VIDEO MENU OF DIFFERENT INPUT MODES---------------------------------------------------------------- 18

2) ADJUST------------------------------------------------------------------------------------------------- 18

Operating Instructions

PRM-3G SERIES

3

3) COLOR TEMPERATURE CONTROL ------------------------------------------------------------------------ 18

4) SCAN ------------------------------------------------------------------------------------------------- 19

5) ASPECT RATIO ------------------------------------------------------------------------------------------ 19

6) ZOOM-------------------------------------------------------------------------------------------------- 19

7) MONO/BLUE ONLY -------------------------------------------------------------------------------------20

8) PEAKING FILTER -----------------------------------------------------------------------------------------20

9) FALSE COLOR -------------------------------------------------------------------------------------------20

10) HDR MODE - OPTIONAL ------------------------------------------------------------------------------21

11) NR (NOISE REDUCTION) ---------------------------------------------------------------------------------21

12) OUTPUT RANGE -----------------------------------------------------------------------------------------21

13) PC MENU (PC MODE ONLY) ------------------------------------------------------------------------------21

14) NTSC SETUP (VIDEO MODE ONLY) -------------------------------------------------------------------- 22

9. AUDIO MENU OPTIONS ------------------------------------------------------------------------------22

1) MAIN / SUB AUDIO OUT ------------------------------------------------------------------------------- 22

2) SDI 1 / SDI 2 AUDIO OUTPUT CHANNEL ---------------------------------------------------------------- 22

3) SDI 1 / SDI 2 AUDIO GROUP --------------------------------------------------------------------------- 22

4) LEVEL METER ------------------------------------------------------------------------------------------- 23

5) LKFS - AUDIO LOUDNESS REAL-TIME MONITORING & LOGGING ----------------------------------------- 24

6) VOLUME------------------------------------------------------------------------------------------------ 25

10. MARKER MENU OPTIONS--------------------------------------------------------------------------- 26

1) MARKER & USER MARKER------------------------------------------------------------------------------- 26

2) SAFETY AREA ------------------------------------------------------------------------------------------- 26

3) CENTER MAKER ----------------------------------------------------------------------------------------- 26

4) MARKER WIDTH ---------------------------------------------------------------------------------------- 27

5) MARKER COLOR ---------------------------------------------------------------------------------------- 27

6) PRESET1 & PRESET2 ------------------------------------------------------------------------------------ 27

11. GPI MENU OPTIONS --------------------------------------------------------------------------------- 27

1) GPI CONTROL & GPI# --------------------------------------------------------------------------------- 27

12. SETUP MENU OPTIONS ------------------------------------------------------------------------------ 28

1) SETUP LOAD & SETUP SAVE ---------------------------------------------------------------------------- 28

2) FUNCTION 1 ~6 ---------------------------------------------------------------------------------------- 29

Re-imagine Beyond Technology [e-mail]

3) ON SCREEN DISPLAY ------------------------------------------------------------------------------------ 30

Operating Instructions

PRM-3G SERIES

4

 OSD Option ---------------------------------------------------------------------------------------- 30

 Time code ------------------------------------------------------------------------------------------ 30

 Under Monitor Display (color: Tally R/G mode action ) ----------------------------------------- 30

 Input ID -------------------------------------------------------------------------------------------- 30

 SDI Signal state ------------------------------------------------------------------------------------ 31

4) ADVANCED --------------------------------------------------------------------------------------------- 31

 Information ---------------------------------------------------------------------------------------- 31

 Control --------------------------------------------------------------------------------------------- 31

 Screen Control ------------------------------------------------------------------------------------- 31

 Fan Control ---------------------------------------------------------------------------------------- 32

 Network Config ------------------------------------------------------------------------------------ 32

 X768 Mode ---------------------------------------------------------------------------------------- 32

5) CAPTION ----------------------------------------------------------------------------------------------- 32

6) WAVEFORM FORMAT (FOR SDI INPUT ONLY) ------------------------------------------------------------ 33

 Y-Pb-Pr Waveform --------------------------------------------------------------------------------- 33

 Y-Waveform + Vector Scope---------------------------------------------------------------------- 33

 Double --------------------------------------------------------------------------------------------- 34

 Y-Waveform + Vector Scope Trans --------------------------------------------------------------- 34

 Vector Color --------------------------------------------------------------------------------------- 34

 Line Select ----------------------------------------------------------------------------------------- 34

 Line # ---------------------------------------------------------------------------------------------- 35

 Line Display ---------------------------------------------------------------------------------------- 35

7) VIDEO RANGE ------------------------------------------------------------------------------------------ 35

8) DUAL LINK MODE (SDI ONLY) --------------------------------------------------------------------------- 35

9) SET ID & ACTIVE SET ID -------------------------------------------------------------------------------- 35

13. PIP (PICTURE IN PICTURE) -------------------------------------------------------------------------36

1) PIP ON/OFF------------------------------------------------------------------------------------------- 36

2) INPUT SOURCE------------------------------------------------------------------------------------------ 36

3) ASPECT RATIO ----------------------------------------------------------------------------------------- 36

4) POSITION----------------------------------------------------------------------------------------------- 37

5) PIP BLEND --------------------------------------------------------------------------------------------- 37

6) PIP SWAP ---------------------------------------------------------------------------------------------- 37

7) AUDIO SELECT ------------------------------------------------------------------------------------------ 37

Re-imagine Beyond Technology [e-mail]

14. OSD TREE -------------------------------------------------------------------------------------------38

Operating Instructions

PRM-3G SERIES

5

1) VIDEO-------------------------------------------------------------------------------------------------- 39

2) AUDIO ------------------------------------------------------------------------------------------------- 40

3) MARKER------------------------------------------------------------------------------------------------ 41

4) GPI ---------------------------------------------------------------------------------------------------- 42

5) SETUP -------------------------------------------------------------------------------------------------- 43

6) PIP ---------------------------------------------------------------------------------------------------- 44

Re-imagine Beyond Technology [e-mail]

• PRECAUTION

Operating Instructions

PRM-3G SERIES

6

Before operating this unit, please read this manual carefully.

WARNING:

To reduce the risk of any electric shock, please do not remove the back cover. No user serviceable parts inside. Refer any service matters to
qualified service personnel. To prevent fire or shock hazard, do not expose the rear of the set to rain or moisture. Do not rub, clean or hit the
Active Matrix LCD with object that may scratch, mark, or damage the Active Matrix LCD permanently.

CAUTION:

Unauthorized tampering with the inside of the monitor invalidates the warranty.

The manufacturer shall not warrant for any damage caused by improper maintenance and/or repair or work by third parties.

Important safeguards for you and your new product:

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or
fire hazards. Please read and observe the following safety points when installing and using your new product and save them for future
reference.

1. Read Instructions

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Notice Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Disconnect the unit from the mains before cleaning the unit. Do not use abrasive cleaners. Use a damp

cloth ONLY for cleaning.

6. Water and Moisture

Re-imagine Beyond Technology [e-mail]

Do not use this product near water surface.

Operating Instructions

PRM-3G SERIES

7

7. Transporting Product

This product should be moved with care. Quick stops, excessive force and uneven surfaces may cause the

product damages.

8. Accessories

Do not use accessories not recommended by PLURA Inc. as they may cause hazards.

9. Ventilation

Do not block any of the ventilation openings.

Install in accordance with the manufacturer’s instructions.

10. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you

are not sure of the type of power supply, consult your power supply company.

11. Power Lead Polarization

This product is equipped with a three-wire grounding-type cord. This is a safety feature. Do not use any

other type power cord.

12. Power Cord Protection

Power-supply cords should be dressed so that they are not likely to be pulled or pinched by items placed

upon or against them.

13. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet. This will prevent possible damage to the product

due to lightning and power-line surges.

14. Grounding the product

This product must be grounded properly to comply with the safety regulations in the country of use. If you

are unsure of these regulations, please consult a qualified electrician.

15. Servicing

Do not attempt to service this product by yourself as opening or removing covers may expose you to

dangerous voltages or other hazards. Refer all servicing to qualified service personnel.

16. Damage Service Required

Isolate this product from the mains and refer to qualified service personnel under the following conditions:

A. If the power-supply cord or plug is damaged.
B. If the front LCD front has been damaged.
C. If the product does not operate correctly by following the operating instructions. Use only the user

control buttons any improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to its normal operation.

D. If the product has been dropped.

Re-imagine Beyond Technology [e-mail]

E. If the product exhibits a distinct change in performance.

Operating Instructions

PRM-3G SERIES

8

17. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety

checks to determine that the product is in proper operating condition and the warranty seal is provided.

18. Mounting

The product should be mounted on a wall as recommended in the instructions.

19. Power

This set operates on an AC supply; the voltage is as indicated on the label on the Manual. This appliance

must be earthed at all times through the chassis as well as through the power lead.

Re-imagine Beyond Technology [e-mail]

1. OVERVIEW

Operating Instructions

PRM-3G SERIES

9

New PRM-3G series including PRM-224-3G offers an elegant slim design integrated with Grade
A -10 BIT OLED 24.5" panel and delivers outstanding BLACK performance, very fast response
time for smooth video with virtually NO motion blur, High contrast of 5000:1, wide viewing
angle, accurate color reproduction and quality picture consistency that meets all your HD &
SD Monitoring application. PRM- 3G series also includes PRM-217-3G, Plura 17" FULL HD
1920x1080 Precision Broadcast LCD Series is built with Grade A - 10 BIT LED 17".

PRM Plura Precision Broadcast LCD Series supports 3 Gbps – 1080P/60P input capability as
well as all other types of digital video formats HD & SD-SDI and analog video formats like
RGB, Component and Composite signals.

2. GENERAL FEATURES

The new PBM-3G has the following advanced features:-

 2 x 3G, 1.5G
 10 bit panel color depth
 Supports up to 2048 x 1080 resolutions
 HDR (High Dynamic Range) capabilities – OPTIONAL
 PQ ( SMPTE ST 2084 ) & HLG ( Hybrid Log Gamma ) – OPTIONAL
 Side by side HDR / SDR mode – OPTIONAL
 RGB 12 Bit Digital Signal Processing
 178° Viewing Angle Display
 Gamma Selectable (0.8 – 3.0)
 Color Temperature – User, VAR, Adjustable (11000K TO 3200K)
 (ICAC) - Plura Intelligent Connection for Alignment & Calibration
 3D LUT ( ITU-R BT 2020, Native, BT.709, SMPTE-C, EBU, NTSC, D-Cinema,

709)

 Display Advanced Waveform & Vector Scope simultaneously with line select.
 Various and User defined Markers Display, Safe Area

Re-imagine Beyond Technology [e-mail]

 Programmable 6 User Front Pushbutton Controls & GPI
 LKFS AUDIO Measurement - Digital Loudness Audio Metering with selected

channel measurement in LFKS scale

 LKFS AUDIO Logging using the optional PSC/500 controller S/W

Operating Instructions

PRM-3G SERIES

10

 Closed Caption (608/708) – North American Market
 Cutting edge De-interlacing and Scaling Technology
 Fast Response Time for high motion video
 Internal Monitor Display (IMD)
 Ethernet & RS232 Remote Control
 Underscan / Overscan / Normal / Zoom
 Pixel to Pixel Mode, Tally, DC Operation
 False Color and Peaking Filter / Focus Assist
 Video Range test with adjustable Y & C values
 Display LTC & DVITC time code with line select
 Embedded Audio Input, Digital Audio Decoding
 Internal Pattern Generator and Wall Control System
 Built In Stereo Speaker, 16 CH Audio Metering Display
 Rack-Mount OPTIONAL
 Battery Mount OPTIONAL

Re-imagine Beyond Technology [e-mail]

3. Functional explanation of each part

Operating Instructions

PRM-3G SERIES

11

1) Front Panel

 PRM-224-3G-O

Tally LED

Headphone

Re-imagine Beyond Technology [e-mail]

LED

 Front Keys Arrangements

Front Key

IR

Speaker

 Front Keys Operations

Operating Instructions

PRM-3G SERIES

12

Key Name Operation

STANDBY

SDI 1
SDI 2

HDMI/DVI

ANALOG
MARKER

SCAN

FUNCTION

F1 ~ 6

MENU

UP

DOWN

SEL/INPUT

Adjust

► Power ON/OFF Button.
► Select SDI 1 source
► Select SDI 2 source
► Select HDMI & DVI source
► Select ANALOG source

( ‘Composite1’ ->‘Composite2’ ->‘Composite3’ -> ‘S-video’ -> ’.B.R’ -> ‘Y.Pb.Pr’ -> ’PC’ )

► Display Marker on Screen ( Off -> 16:9 -> 4:3 … -> 2.35:1 )
► Executes Scan function ( Over-Scan -> Zero-Scan -> Under Scan-> Pixel to Pixel)
► When pushed it will display a list of the 6 function keys and what they are currently set

to.

► F1 ~ F6 Programmable KEYS.
► Executes functions of user selected

UNDEF, Marker Size, Audio LV Meter, Wf/Vector, H/V delay. Aspect, Audio
Loudness(LKFS), Mono/Blue only, Audio Channel, Safety marker size, Time code, Caption,
Audio mute, Still image, Zoom, Flip, Gamma select, Vector Color, Fan Control, I/P Mode,
Marker Preset1, Marker Preset2, WFM Line Select, PIP func & Input, Sub win full, Sub win
part

► Activates main OSD menu.
► Navigates higher menu in main OSD menu.
►Exits OSD menu.

► Increases Audio volume of speaker.
► Increases values of user menu in main OSD menu.
► Executes function (by OSD help commands) in main OSD menu.

► Decreases Audio volume of speaker.
► Decreases values of user menu in main OSD menu.
► Executes function (by OSD help commands) in main OSD menu.

►Activates OSD menu of input source selecting.
►Changes input source by selecting.
►Executes functions (by OSD help commands) in main OSD menu.

► Adjust Picture Menu(Volume -> Brightness -> Contrast -> Color -> Sharpness-> & Tint)
► Turn Right (with ‘UP' button is same)
► Turn Left (with ‘DOWN' button is same)

- Power ON mode is LED Green

- Stan-by mode is LED Red

Re-imagine Beyond Technology [e-mail]

 Front panel LED Operations

 Speaker Out

Interface Description

Speaker R/L out 8 ohm±15%, Max 4W + 4W

2) Rear Panel

Operating Instructions

PRM-3G SERIES

13

 Conne

ction Details

 Power IN

DC 24V IN

1

2

4

3

IN NO Description

1,2 GND
3,4 + 24V

 RJ-45- GPI, Control LAN / (Ember+) OPTIONAL

GPI CONTROL LAN RJ 45 Jack Face

Remote PIN Assignment

8 PIN COMMON(GND) 4 PIN GPI 4 PORT
7 PIN

(STAND BY/POWER ON/OFF)
6 PIN GPI 6 PORT 2 PIN GPI 2 PORT
5 PIN GPI 5 PORT 1 PIN GPI 1 PORT

GPI 7 PORT

3 PIN GPI 3 PORT

Re-imagine Beyond Technology [e-mail]

Control Terminal: 1 ~ 7 Pin

Operating Instructions

PRM-3G SERIES

14

GND Terminal: 8 Pin of RJ-45

 Interface description

Interface Description

Contact Point Switch

SDI 1 IN

SDI 2 IN
SDI 1 OUT
SDI 2 OUT

HD SDI / SD SDI Input

SDI 1, SDI 2 Loop Out

RS-232 IN Update/Multi Control/Auto color calibration

RS-232 OUT Multi Control out

HDMI High Definition Multimedia Input
DVI-I

CVBS1/Pr/R In

CVBS2/Y/G/Y In

CVBS3/Pb/B/C In

DVI-I Type Digital / Analog PC-RGB Video Input
High Definition Multimedia Input Compatible

GBR (SOG sync) Input
Y, Pb, Pr Component Video Input
CVBS / Composite/S-Video Input

CVBS1/Pr/R Out

Component/GBR/Composite1,2,3/ S-Video Loop OutCVBS2/Y/G/Y Out

CVBS3/Pb/B/C Out

AUDIO R In

AUDIO L In
AUDIO R Out
AUDIO L Out

DVI-I/Component/GBR/Composite1,2,3/S-Video Sound Input

AUDIO MONITOR OUT

AC IN AC90V ~ 240V, 50Hz/60Hz
DC IN DC 24V

UPDATE Firmware Upgrade

GPI GPI 1 ~ 7 Control Port

Re-imagine Beyond Technology [e-mail]

4. MENU OVERVIEW

Operating Instructions

PRM-3G SERIES

15

In this system menu, there are several ways to maneuver the menu settings.
Most menus consist of three levels to select the necessary option, but some settings require greater depth.
If you press the MENU button, the first and second level of the menu system will appear on the monitor
screen. The third level can be displayed by pressing SEL/INPUT. If a menu has more than three levels,
the pop-up dialogue box will be displayed as the fourth or fifth level.

1. To show and remove the Menu

Press the MENU button to display the menu. Press the MENU button again to hide the menu.

2. To go to the next level

Press SEL/INPUT button.

3. To go back to the previous level

Press MENU button

4. Typical Menu Operation

1. Press MENU button: The main menu will be displayed.

2. Use UP/DOWN button to select the desired menu option (icon).

3. While the desired menu option is selected, press SEL/INPUT to move to the second level.

4. Use UP/DOWN button to select the second menu option.

5. Press SEL/INPUT to move to the third level: Some menu options require additional steps.

6. Press MENU to return to the previous menu to return to monitor viewing.

5. BASIC OPERATION

1. Turning On the Monitor

1. Firstly, make sure you have connected the AC power cord or DC XLR connector. The monitor will switch
to standby or power on mode. If the monitor is in standby mode, press the ST-BY button to turn on the
monitor.

2. Select the source by using SEL/INPUT button on Keypad in front of monitor

Re-imagine Beyond Technology [e-mail]

2. Volume Adjustment

Operating Instructions

PRM-3G SERIES

16

1. Press the ADJUST button on Keypad.

2. Press the MENU button on Keypad.

- OSD Audio menu -> Volume menu.

3. On Screen Menu Language Selection

- SETUP -> On Screen Display -> OSD Option -> Language

- The menu can be shown on the screen in the selected language.

- Supported Languages: English, Spanish, Portuguese, German, French,

Italian, Hindi

6. On Screen Menus Selection and Adjustment

1. How to adjust the OSD screen

1. Press the MENU button and then UP/DOWN button to select each menu.

2. Press the SEL/INPUT button and then use UP/DOWN (SEL/INPUT)/MENU button to display

the available menu.

• The monitor’s OSD (On Screen Display) may differ slightly from what is shown in this manual.

Re-imagine Beyond Technology [e-mail]

 SELECT VIDEO INPUT

Operating Instructions

PRM-3G SERIES

17

1. How to Select Video Source by OSD

1. Press the SET/INPUT button and then UP/DOWN button to select the required video source.

2. Press the SET/INPUT button to select the desired video source.

3. If Input Name is enabled, The SET/INPUT button will show the input name previously programmed

instead of the source name.

Re-imagine Beyond Technology [e-mail]

8.

Operating Instructions

PRM-3G SERIES

18

VIDEO M

ENU OPTIONS

9. Video Menu of different Input modes

< Video (NTSC) Picture menu> < PC Picture menu> < SDI, HDMI Picture menu>

2) Adjust

- Adjust the values of Brightness, Contrast, Color, Tint and
Sharpness range from -50 to 50

Contrast, Brightness, Sharpness, Color (All Sources), Tint (except

PC, DVI, HDMI, Component), Phase (Component).

3) Color Temperature Control

- For Setting the Color temperature or adjusting RGB gain value

- User (User setting RGB gain value), VAR(3200K ~ 11000K), Often used value(11000K, 9300K, 6500K,
5400K,3200K) and 3D LUT Calibration value(D65 – 6504K/C-6774K/D-Cinema 6302K)

- Color Space: Native/BT.709/SMPTE-C/EBU/NTSC/D-Cinema

Re-imagine Beyond Technology [e-mail]

4) SCAN

Operating Instructions

PRM-3G SERIES

19

5) Aspect Ratio

1. Over Scan – 95% input size and fit the selected display size

2. Zero Scan – 100% Input size and fit the selected display size

3. Under Scan – 105% Input size and fit the selected display size

3. Pixel to Pixel – Display size is an input size. If input resolution
is bigger than panel size, fit the panel size

- For setting the aspect ratio.

- Full Screen: The images are displayed with a panel size.

- Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1: The images are displayed with each aspect ratio.

- Funtion-key operate Rotation, Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1

- AFD function Added

- PC mode: Full Screen & 4:3 only

6) Zoom

- Can enlarge picture by (2X, 3X, 4X, 5X) ratios.

- If user selects the Zoom 2X, Yellow box will be displayed.

- Press Select or Enter button, the monitor will display a zoom in
portion of this specified location.

- Press Menu key to exit the zoom mode.

- Example (3X3)

Re-imagine Beyond Technology [e-mail]

Zoom X position: Coordinate of vidideo image’s column position.

Operating Instructions

PRM-3G SERIES

20

Zoom Y position: Coordinate of vidideo image’s row position.

7) Mono/Blue Only

- Mono color: For selecting monochrome imagees.s.

- Blue Only: Blue Video channel is enabled

8) Peaking Filter

-Peaking Filter: Peaking Filter On/Off.

-Peaking Color: Red/Blue/White/Violet.

-Peaking Level: 0~100.

Re-imagine Beyond Technology [e-mail]

9) False Color

- False Color on/off

10) HDR Mode - OPTIONAL

Operating Instructions

PRM-3G SERIES

21

- ST 2084-300 / ST 2084-1000 / ST 2084-10000 / HLG

- HDR Demo on/off

- HDR Demo split the screen vertically and shows the image
with and without HDR.

11) NR (Noise Reduction)

-Noise Reduction on/off. (NR is for (HD-SDI, Composite, S-Video and Y.Pb.Pr) Video signal.

12) Output Range

- Normal (16~235)/Full (0~255)

- Operate Only in PC input mode

Re-imagine Beyond Technology [e-mail]

13) PC Menu (pc mode only)

- Select Auto-adjust and adjust Phase, HV position, Frequency

Operating Instructions

PRM-3G SERIES

22

- Auto-Adjust automatically set the optimum values of Phase, HV position and Frequency.

14) NTSC Setup (Video mode only)

- IRE value under NTSC mode between 0 IRE and 7.5 IRE.

9. AUDIO MENU OPTIONS

1) MAIN / SUB Audio out

-Main: Select Internal Speaker out. (Auto/SDI1/SDI2/HDMI/Line
in)

-Sub: Select sub display sound. (Auto/SDI1/SDI2/HDMI/Line in)

- Audio output channel source select. (Channel1~4, Channel1/2, Channel3/4, off)

Re-imagine Beyond Technology [e-mail]

2) SDI 1 / SDI 2 Audio Output Channel

3) SDI 1 / SDI 2 Audio Group

- Select primary or secondary audio group to decode. (Group 1~4)

Operating Instructions

PRM-3G SERIES

23

4) Level Meter

- Display the audio level meter on screen in SDI input.

-Pair: Pair L & R channel display

-Group: Group display

- Level Meter Position selects. (TOP/Middle/Bottom)

- Level Meter Scale mode selects. (BBC / EBU / VU / NORDIC /
DIGITAL / DIN / EXPAND DIN)

Re-imagine Beyond Technology [e-mail]

5) LKFS - Audio Loudness Real-Time Monitoring & Logging

Operating Instructions

PRM-3G SERIES

24

-Audio Loudness setting (On, Off) and Set Target(LKFS)

-Audio Loudness Real-Time monitoring.

Re-imagine Beyond Technology [e-mail]

-Audio Loudness Real-Time logging on a remote PC using the optional PSC-500 (Plura System Controller

Operating Instructions

PRM-3G SERIES

25

Utility).

- Adjust the speaker or headphone Volume level. (0~32)

Re-imagine Beyond Technology [e-mail]

6) Volume

10. Marker MENU OPTIONS

Operating Instructions

PRM-3G SERIES

26

1) Marker & User Marker

< Marker > < User Marker >

- Marker : 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1&4:3, User1, User2, User3 (Customized markers).

- User Marker: The user defined Marker size setting.

16:9 (16:9 Marker) 16:9 (4:3 Marker)

2) Safety Area

-Safety Area: Display safety area Marker on screen with below
options.
(16:9 95/93/90/88/80%, 4:3 95/93/90/88/80%,
EBU Action 16:9/14:9/4:3, EBU Graphic 16:9/14:9/4:3)

3) Center Maker

- “+” display Marker on center of screen

Re-imagine Beyond Technology [e-mail]

4) Marker Width

Operating Instructions

PRM-3G SERIES

27

-Marker line thickness setting. (0~10)

5) Marker Color

- Marker Line Color: Select Marker line color (White, Yellow, Blue,
RED, Black)

- Safety Line Color: Select Safety line color (White, Yellow, Blue,
RED, Black)

- Marker outside area color: Select Marker Back Color. (None, Gray,
White, Blue, Black)

- Safety outside area color: Select Safety Back Color. (None, Gray,
White, Blue, Black)

- Marker BK Blend Color: Select Marker blend level. (0 ~ 5)

- Safety BK Blend Color: Select Safety blend level. (0 ~ 5)

6) Preset1 & Preset2

- Markers can be set as preset 1 & 2 and be triggered by GPI controller.

- GPI preset markers can only be utilized by GPI controller.

11. GPI MENU OPTIONS

1) GPI Control & GPI#

- For allocating functions to particular GPI pins.

- Remote control operations can be performed using the GPI Controller.

- GPI Control: GPI function Enable/Disable

- GPI 1 ~ 7

Re-imagine Beyond Technology [e-mail]

GPI Function Description

Operating Instructions

PRM-3G SERIES

28

UNDEF Not set (no function allocated)
Marker1 On/Off, Marker2 On/Off Displays the markers which have been set by

the GPI PRESET1, 2 items on the screen.
Center Marker Displays the center marker.
Safety Area Displays the Safety Area.
Tally R, Tally G For enabling the Red or Green or amber tally

lamp.
Scan Over Scan/Zero Scan/Under Scan/ Pixel to

Pixel
Input Composite1,2,3 Input R.G.B, Input SDI1,

Input SDI2,Input Y.Pb.Pr , Input PC ,
Input DVI, Input HDMI

Menu Key, Enter Key, Up Key, Down Key
Left Key, Right Key

Function key1 ~ 6
H/V delay H delay, V delay, HV delay, Off
Aspect Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1,

Waveform Display the Waveform / Vector
LKFS Warning LKFS On/Off
GPI 7 : Power Key(Fixed)

Switches the input source.

Use the key function by GPI.

2.35:1

12. SETUP MENU OPTIONS

1) Setup Load & Setup Save

- Setup Load: Load user saved values or default value

- Setup Save: Save user setting values at user 1, 2, 3.

Re-imagine Beyond Technology [e-mail]

2) Function 1 ~6

Operating Instructions

PRM-3G SERIES

29

- Function 1~6 : Function buttons can be programmed to any function from the below table.

Function1~6 button Description

UNDEF Not set (no function allocated)
Marker size Marker size Select
Audio Lv Meter Audio Lv Meter On / Off
WF/Vector Display the Waveform
H/V delay H delay, V delay, HV delay, Off
Aspect Sets the aspect ratio of the images
Audio Loudness Display Audio Loudness
Audio Group Select the de-embedded audio Group in SDI input.
Audio Channel Select the de-embedded audio channel in SDI input.
Mono/Blue Only Mono color or Blue Only
Safety Area Marker Safety Area Select
Time Code Time Code Display
False Color False Color On/Off
Audio Mute Toggles sound status of speaker/headphone & mute.
Still Image Still Image On/Off
Peaking Filter Peaking Filter On/Off
Gamma Select Gamma Level Select (0.8 ~ 3.0)
Vector Color Select 100% or 75% range
Fan Control Internal Fan Controls option by temperature sensor Auto / force on /

force off
I/P Mode Line Doubler / Inter-Field / Field Merge
Marker Preset 1/2 Display the markers which have been set by the PRESET1, 2 items on

the screen.
WFM Line Select WFM Line Select On/Off
PIP Func & Input PIP func & input Select
Sub Win Full Display the same full images on POP1 screen
Sub Win Part First image scale 4:3 aspect ratio and then display on POP2 screen

Re-imagine Beyond Technology [e-mail]

3) On Screen Display

Operating Instructions

PRM-3G SERIES

30

 OSD Option

 Language: Select the desired Menu language from list below.

(English, Spanish, Portuguese, German, French, Italian)

OSD Position: L-T, R-T, C, L-B, R-B
 OSD Transparency: Disable blending OSD background with video image.
OSD Time out: OSD display time setting. (3~200)

 Time code

 Time code Enable: Time code Display (off/ATC/DVITC, SDI only)
Time code size: Time code size select. (Small, Middle, Large)
Time code Position: Time code display position selects (L-T, C-T, R-T, L-B, C-B, R-B)
 Time code Transparency: Enable/Disable Timecode background blending with video image. (0%, 25%,

50%, 75%, 100%)

 Under Monitor Display (color: Tally R/G mode action )

Channel-12

UMD

 UMD: UMD display on/off
 UMD Character: UMD Character Select
 UMD Position: UMD display position selection (L-T, C-T, R-T, L-B, C-B, R-B)
 UMD FG Color: UMD Character color Selection (RGB_255_192_128_Transparent)
 UMD BG Color: UMD BG color Selection (RGB_255_192_128_Transparent)

 Input ID

Channel-12

Tally Red

Channel-12

Tally Green

Message OSD

SDI1 1920 x 1080i 60Hz

Info Message

00:00:00:00

Timecode

Input ID: source Message display.
ID Style: select “Input Format”/”Custom Label”
Input Label: Display custom ID name instead of input source name on source OSD and message OSD

Re-imagine Beyond Technology [e-mail]

 SDI Signal state

Operating Instructions

PRM-3G SERIES

31

SDI Signal state display on/off (H/V sync, image, Audio, Audio Phase, EDH packet, EDH FF CRC, EDH
APCRC, SAC, EAV, VPI)

4) Advanced

- Information, Control, Screen Saver, Screen Control, Fan Control,
x768 Mode

 Information

- Version, Release day, Release time, operating time, FPGA Version, Calibration ID

 Control

 Screen Control

- FRONT LED: Front LED on/off

- Local Enable: All buttons except Power, up and down keys are
enabled when Local enable is off.

- Remote Enable: Allows you to choose between local or remote
controller. If remote controller is selected, both local (front key)
and remote are enabled. However if local is selected, remote
control is diabled.

-Reset Calibration
Color Calibration Reset

-Backlight Adjust
Inverter dimming Level select (0~100)

-Gamma Select
Gamma Level Select (0.8 ~ 3.0)

-I/P Mode
 Line Doubler / Inter-Field / Field Merge

-Dithering
 Dithering function on/off

Re-imagine Beyond Technology [e-mail]

- Internal Pattern

Operating Instructions

PRM-3G SERIES

32

100% Color Bars, 75% Color Bars, Luma, RGB, White, Black, RED, Blue, Green

 Fan Control

 Fan Control: Internal Fan temperature sensor control options:-

Auto / force on / force off

 Fan Active Temperature: Fan control by temperature settings in
Celsius degree and Fan Control setting should be set to Auto.
 Hysteresis: Adjusts fan hysteresis temperature by Celsius degree.
(1~10℃)

 Shutdown: Monitor will shut down if temperature reach 75℃,
Power Off.

 MCU Fan Control: Control main MCU Fan On/Off

 Network Config

Plura System Controller (PSC-400/500) Network setting.
Load Network Settings: Connect to your network and press

“Enter”. (IP Address/Gateway/Subnet Load)
DHCP: DHCP on/off (Manual IP settings – DHCP on)
* “Apply” enter all settings.

 X768 Mode

-Selects X768 native PC video timings. (Auto/1024x/1280x/1360x/1366x)

5) Caption

Closed Caption: select 608 Line21, 608 ANC, 608 Transcoded, 708 mode

Re-imagine Beyond Technology [e-mail]

- V-Chip : On/Off

Operating Instructions

PRM-3G SERIES

33

- 608 Caption channel: C/C1, C/C2, C/C3, C/C4, TEXT1, TEXT2, TEXT3, TEXT4

- 708 Caption Service: Service 1/Service 2

6) Waveform Format (For SDI input ONLY)

Press the WAVEFORM button to display the WAVEFORM Mode

 Y-Pb-Pr Waveform

- Y_Pb_Pr WAVEFORM & Audio Lever Meter & Info Window & Time code Display.

 Y-Waveform + Vector Scope

Re-imagine Beyond Technology [e-mail]

- WAVEFORM & Vector Scope & Audio Lever Meter & Info Window & Time code Display.

Operating Instructions

PRM-3G SERIES

34

 Double

SDI 1 SDI 2

- SDI 1, 2 & WAVEFORM & Vector Scope & Audio Lever Meter & Info Window.

 Y-Waveform + Vector Scope Trans

- WAVEFORM & Vector Scope Trans.

 Vector Color

- Vector color: Select 100% or 75%

 Line Select

Re-imagine Beyond Technology [e-mail]

- Select line WAVEFORM & Vector Scope display.

Operating Instructions

PRM-3G SERIES

35

- line select : 1~540

 Line #

-line select

 Line Display

-off/on/5 sec

7) Video Range

-Range Check: Range Check on/off.

-Y Max: Maximum luminance level.

-Y Min: Minimum luminance level.

-C Max: Maximum chroma level.

-C Min: Minimum chroma level.

-Color: Black/Blue/Red/Green

-Grid: Grid line on/off

-Blink: Y/C Min-Max to blink. (0~7)

8) Dual Link Mode (SDI only)

-Dual Link Mode select. (Auto/Off/RGB444/YCbCr444/YCbCr422/Progressive)

9) Set ID & Active Set ID

- To control any monitor, the monitor must have a unique ID number from (01~99).

- Set Active SET ID number to allow Remote control or RS-232 access

- If controlling total of 15 monitors , Active SET ID must be set 15.

Re-imagine Beyond Technology [e-mail]

13. PIP (Picture In Picture)

Operating Instructions

PRM-3G SERIES

36

- Display two programs or sources at the same time. And set up PIP size and position.

- Only Dual Link model Select

1) PIP ON/OFF

Control PIP function On/Off.

2) Input Source

- PIP input Source can be selected from the drop down menus.

- Analog (Composite1, 2, 3, Y.Pb.Pr, GBR, PC) inputs + Digital (DVI, HDMI) + SDI (SDI1, SDI2) inputs

-SDI + SDI input PIP

3) Aspect Ratio

PIP Small

- Choose PIP size Small/POP1/POP2

PIP1

POP2

Re-imagine Beyond Technology [e-mail]

4) Position

Operating Instructions

PRM-3G SERIES

37

- Choose the pip position on the eacchh corner of the panel

5) PIP Blend

-Blend to PIP signal

6) PIP Swap

- Using Swap option, you can exchaange two programs or sources with swap function.

7) Audio Select

- Using Sound Swap option, you caann exchange the audio to either program or source.

Re-imagine Beyond Technology [e-mail]

14. OSD TREEEE

Operating Instructions

PRM-3G SERIES

38

Re-imagine Beyond Technology [e-mail]

1) Video

Operating Instructions

PRM-3G SERIES

39

Re-imagine Beyond Technology [e-mail]

2) Audio

Operating Instructions

PRM-3G SERIES

40

Re-imagine Beyond Technology [e-mail]

3) Marker

Operating Instructions

PRM-3G SERIES

41

Re-imagine Beyond Technology [e-mail]

4) GPI

Operating Instructions

PRM-3G SERIES

42

Re-imagine Beyond Technology [e-mail]

5) Setup

Operating Instructions

PRM-3G SERIES

43

Re-imagine Beyond Technology [e-mail]

6) PIP

Operating Instructions

PRM-3G SERIES

44

Re-imagine Beyond Technology [e-mail]

Contact Us

Operating Instructions

PRM-3G SERIES

45

Corporate Offices:

Plura Broadcast, Inc.

Ph: [phone]

[e-mail]

Plura Europe GmbH

Ph: [phone]

U.S.A.

GERMANY

[e-mail]

Plura MEA

Ph: [phone]

[e-mail]

Plura Asia

Ph: [phone]

[e-mail]

U.A.E.

S. KOREA

Re-imagine Beyond Technology [e-mail]