Plura PBM-070, PBM-070X Operating Instructions Manual

Operating
Instructions

Multi Format HD Broadcast Monitor

PBM-070 (7”)

PBM-070X (7”)

Important Safety Instructions

1. Please read this manual thoroughly before operating the monitor.

2. Unplug monitor from the wall outlet before cleaning the LCD screen. Do not use liquid cleaners or aerosol

cleaners. Use ONLY a damp cloth provided.

3. Don’t use any unauthorized accessories not recommended by the manufacturer as they may cause

hazards.

4. Don’t operate this monitor near damp or wet surfaces.

5. Use only the recommend manufacturer mounting hardware accessories.

PORTABLE CART WARNING

(symbol provided by RETAC)

Slots and openings in the cabinet and the back or bottom are provided for
ventilation, and to insure reliable operation of the monitor and to protect it
from overheating, these openings must not be blocked or covered.

6. This appliance should be operated only from the type of power source

indicated on the marking label.

If you are not sure of the type of power supplied to your home, consult your

dealer or local power company. For appliance designed to operate from
battery power, refer to the operating instructions.

7. This appliance system is equipped with a 3-wire grounding type plug (a plug having a third (grounding) pin).

This plug will only fit into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your electrician to replace your outlet.
Do not ignore the safety purpose of the grounding plug.

8. For added protection for this product during a lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning
and power-line surges.

9. Do not allow anything to rest on the power cord.

10. Follow all warnings and instructions marked on the appliance.

11. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

12. Do not attempt to service this monitor without a qualified service personnel.

2

FCC Notice

This device complies with Part 15 of FCC Rules.

Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

To assure continued compliance, follow the attached installation instruction and do not make any unauthorized
modifications.

Note:

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The user may find the booklet “Something About Interference” available from FCC local regional offices helpful.

Warning:

To assure continued FCC emission limit compliance, the user must use only shielded interface cables when
connecting to host computer or peripheral devices. Also, any unauthorized changes or modifications to this
equipment could void the user’s authority to operate this device.

3

Safety Precautions

WARNING:

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE ELECTRICK SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD,
KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS. USE
AND STORE ONLY IN LOCATIONS WHICH ARE NOT
EXPOSED TO THE RISK OF DRIPPING OR SPLASHING
LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS
ON TOP OF THE EQUIPMENT.

CAUTION:

In order to maintain adequate ventilation, do not install or
place this unit in a bookcase, built-in cabinet or any other
confined space. To prevent risk of electric shock or fire
hazard due to overheating, ensure that curtains and any
other materials do not obstruct the ventilation.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND
ANNOYING INTERFERENCE, USE THE RECOMMENDED
ACCESSORIES ONLY.

CAUTION:

This apparatus can be operated at a voltage in the range of

100-240 V AC.

THIS EQUIPEMNT MUST BE GROUNDED

To ensure safe operation, the three-pin plug must be inserted
only into a standard three-pin power outlet which is effectively
grounded through normal household wiring. Extension cords
used with the equipment must have three cores and be
correctly wired to provide connection to the ground. Wrongly
wired extension cords are a major cause of fatalities. The
fact that the equipment operates satisfactorily does not imply
that the power outlet is grounded or that the installation is
completely safe.

For your safety, if you are in any doubt about the effective
grounding of the power outlet, please consult a qualified
electrician.

CAUTION:

THE AC RECEPTACLE (MAINS SOCKET OUTLET) SHALL
BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE
EASILY ACCESSIBLE.

TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM
THE AC MAINS, DISCONNECT THE POWER CORD PLUG
FROM THE AC RECEPTACLE.

Voltage other than 120V are not intended for U.S.A and

Canada.

CAUTION:

Operation at a voltage other than 120V AC may require

the use of a different AC plug. Please contact either a local
service center for assistance in selecting an alternate AC
plug.

Notice (U.S.A. only):

This product has a fluorescent lamp that contains a
small amount of mercury. It also contains lead in some
components. Disposal of these materials may be regulated
in your community due to environmental considerations. For
disposal or recycling information please contact your local
authorities, or the Electronics Industries Alliance:

http://www.eiae.org.

4

Safety Precautions continued

Caution for AC Power Cord

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
Appropriate AC Power Cord must be used in each local area.

FOR CONTINENTAL EUROPE, ETC

Not for use in the U.K.

FOR U.S.A. and Canada

Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)

This symbol on the products and/or accompanying documents means that used electrical and

electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling, please take these products to designated
collection points, where they will be accepted on a free of charge basis. Alternatively, in some
countries you may be able to return your products to your local retailer upon the purchase of an
equivalent new product.

FOR U.K. ONLY

If the plug supplied is not suitable for your socket outlet,
it should be cut off and appropriate one fitted.

Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects
on human health and the environment which could otherwise arise from inappropriate waste handling. Please
contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of
disposal.

CE NOTICE

This is Class B product. In a domestic environment this may cause radio interference in which
case the user may be required to take adequate measures.

The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.

5

Contents

1. Outline ....................................................................................................................... 7

2. Main Features ............................................................................................................ 7

3. Controls and Functions .............................................................................................. 8

3-1. Front Panel ........................................................................................................ 8

3-2. Rear Panel ....................................................................................................... 10

3-3. Tally & Audio .................................................................................................... 11

3-4. Function Buttons for FUNCTION 1 and FUNCTION 2 ....................................... 13

4. Display Status .......................................................................................................... 13

5. INPUT Select Menu.................................................................................................. 14

6. Control and Use of OSD Menu ................................................................................. 15

6-1. Video ............................................................................................................... 15

6-2. Display ............................................................................................................. 16

6-3. Color ................................................................................................................ 18

6-4. Marker ............................................................................................................. 19

6-5. OSD Setup ...................................................................................................... 20

6-6. Audio ............................................................................................................... 21

6-6. GPI Control ...................................................................................................... 21

6-7. System Configuration ....................................................................................... 22

7. How to use Program Update Port ............................................................................ 22

8. Remote Terminal Assignment ................................................................................... 23

9. List of Compatible Signal Formats ............................................................................ 25

10. Specifications .......................................................................................................... 27

11. Dimensions .............................................................................................................. 28

12. Troubleshooting ....................................................................................................... 29

13. Maintenance ............................................................................................................ 29

14. Update and Modification of Product ......................................................................... 29

6

1. Outline

The PLURA PBM-070/PBM-070X is a comprehensiveand powerful monitor that consists of true black wide screen
7” LCD with LED backlighting technology that graties all type of users. The PBM-070/PBM-070X Series supports
HD / SD-SDI, RGB, Component and Composite signals.

The PBM-070/PBM-070X offers an elegant slim design with fast response time for smooth video streaming, high

brightness, contrast ratio, wide viewing angles, accurate color reproduction and quality picture consistency
that meets your HD Monitoring application.

The PBM-070/PBM-070X supports an auto calibration mechanism using ICAC (Intelligent Connection for Alignment

& Calibration) and sophisticated calibration tools to adjust and calibrate color temperatures and gamma settings.

In addition the new and advanced Plura PBM-070/PBM-070X supports Closed Captioning CEA (608 / 708),
advanced Waveform (Y.Cb.Cr, selectable), Vector Scope (75%,100%), and EBU / User Markers & Source ID display.

The PBM-070/PBM-070X also provides various display functionality such as time code, audio metering display and

offers user friendly menu functions to control brightness, color temperature and EQ function of HD SDI input.

2. Main Features

• Complies with EBU-2330 TECH, SMPTE-C and ITU-R BT.709 Standards

• Cutting edge De-interlacing and Scaling Technology

• RGB 10 Bit Digital Signal Processing

• Fast Response Time for high motion video

• 178° Viewing Angle Display

• HD/SD SDI, Composite, RGB, YUV, Y/C, UXGA & DVI Inputs

• Supports all HD/SD signal formats @ 50Hz and 60Hz respectively

• HD2 K Format

• Analog & Embedded Input/Out, Built In Stereo Speaker, Ear Phone Jack

• Intelligent Connection for Alignment & Calibration (ICAC)

• Pixel to Pixel Mode, Tally, DC Operation

• Waveform (Y.Cb.Cr, selectable), Vector Scope (75%,100%)

• 16 CH Audio Metering Display, VITC

• Various and User dened Markers Display, Safe Area in HD & SD

• H/V delay, Blue only & Mono mode

• Picture and Picture (PaP), Picture in Picture (PiP) mode display & source ID display.

• Closed Caption Decoding (608/708) and V-chip

• Underscan/ Overscan/ Normal / Zoom

• Programmable Front Pushbutton Controls, Intuitive OSD Display

• External RemoteControl (RJ-45), Serial/Upgrade Port( RJ-11)

• Programmable GPI control & RS232 Remote Control

• Wall Control System

Please, refer to Specification Sheet for detailed Options

7

3. Controls

3-1. Front Panel

2 3 4

1

2

3

4

5

6

STANDBY

SDI INPUT SELECT

CVBS 1, CVBS 2, CVBS3 Y/C (S-VIDEO) INPUT SELECT

YPbPr, RGB INPUT SELECT

DVI / VGA INPUT SELECT

SCAN

7 BLUE/GRAY ( )

8

W-FORM/VECTOR

9 FUNCTION 1 (F1, F2)

8

5 6 7 8

Power ON/OFF Button.

This

is for

selecting SDI

This is for selecting CVBS
this button, it converts CVBS1,2,3

This

is for

selecting YPbPr,

Each time the user

This is for selecting

Selects
(SCAN LED

1)
Each

2) When

Pixel

1) When this button is

time this button is

These functions are available only in SDI, CVBS, S-Video, YPbPr

Functions
section “3-4 Front.

Zero Scan , Under Scan,

is ON when

Display

color is only shown with Blue or with

time this button is

W-FORM/VECTOR

to Pixel.

are

assigned

Input.

presses

DVI / VGA

Over

pressed,

pressed,

pressed,

from the

Function

Additional OSD LOGO

&

S-Video Input. Additional OSD LOGO is displayed. Each time the user presses

RGB

this button, it converts

Input. Additional OSD LOGO is

Scan Mode is activated)

Mode is

it

converts

for F1,F2.”

Front Push

PBM–070

Mode.

(Components)

Over

Scan, Zoom Mode.

the

display

activated,

Display Color is shown as a format of Waveform or Vector Scope. Each

each mode.

SYSTEM

9 10 11 12 13 1

Buttons

input.

Luminance (Color off)

mode changes

this button is used to

menu.

They

is displayed.

YPbPr(YUV),

displayed.

are operated by the F1, F2 Buttons Please

RGB

Mode.

Mode.

change

14

the position of Waveform,

refer to

3. Controls continued

10

MENU

When pressing
for more

11

Marker ( )

This activates
When

12

UP ( )

When

13

ENTER

1) Menu is set by using the
Please refer

2) If

Enter

input

14

ADJUST VOLUME

When front control KNOB is

it

is

deactivated. User

Clock Wise

this button, the

detailed

information.

OSD MENU

is

the

using the

using the

OSD

OSD

to section 6 “OSD

marker display

Menu, this works as a Down Button.

Menu, this works as an Up Button.

function

Enter

Key. After setting a function, move to the next step.

MENU

CONTROL” for more

Button is pressed when “Menu” is not ON, it

signal

information.

(Brightness,

Contrast, Saturation, Phase, Volume)

pressed, corresponding

can set the

desired value

displayed. Please refer

detailed

displays a OSD LOGO

VOLUME MENU

to section 6 “OSD

information.

window that shows current

is

activated,

by turning this KNOB button into Clock

Brightness
Contrast
Chroma

Possible

to control these functions.

Phase

Speaker Volume

and

MENU

if

pressed

Wise

or Counter

DISPLAY”

again,

9

3. Controls continued

3-2. Rear Panel

10

Use only the

designated

specific country of use.

Rear

PBM-070/PBM-070X

power cord to

ensure

the

Safety

and

EMC regulation

for the

3. Controls continued

465

465

1

3

7

9

SDI 1 Input Terminal ,BNC

These connectors are for HD/SD-SDI input signal and support SMPTE standard and 16

ch. audio signals.

SDI LOOP OUT Active Terminal ,BNC

Output terminals for HD/SD-SDI signals.

CVBS (Composite) 1,2,3 /Y, Pr, Pb / G, R, B / Y,C Input Terminal (BNC)

This is the Analog input terminal. Three types of input signal are supported.

1) Composite 1,2,3

2) Component Y,U,V (Y,Pb,Pr) and R,G,B

3) S-Video(Y,C).

Please refer to section 5 “Input Select” for more detailed information.

LOOPOUT Terminal ,BNC -> Option

Loop output terminal of Analog input signal. If you do not need the LOOP output, select
“Analog Loop: NO” in the OSD menu.

DVI-I / PC-RGB Input Terminal (DVI-I Jack)

1) DVI Digital Signal Input.

2) When using DVI to VGA Gender, PC-RGB(VGA) Signal Input available.

REMOTE Port ,RJ-45 Jack –Through (RJ-45)Terminal -> Option

Terminal for controlling the monitor by an external control. (Make/Trig Type)
Please refer to section 8 “Remote Terminal Assignment” for more detailed information.

10

11

12

Audio Input/Output Terminal

Input/Output terminal for the external Audio and Embedded Audio Signal.
Please refer to 3-3 Audio Input/Output.

UPDATE Port (RJ-11 Jack)

Serial Communication Port
This port is used to modify the monitor program or to control the Monitor.
Please refer to section 7 “Program Update Port” for more detailed information,

DC INPUT Terminal

Used to supply DC power. Please verify DC voltage Input. In case of Battery power, the

range is 11V to 17V.

11

3. Controls continued

3-3. Tally & Audio

1. Tally

2. Audio

1

2

Input/Output

Analog Audio L/R Input Terminal (RCA Phone Jack)

Analog Audio L/R Input Terminal

The external

Analog Audio L/R Output Port (Stereo Pin Jack)

Te rmi nal
available

12

Three Tally Colors are supported by external contact terminal

GPI 5 ON=> RED, GPI 6 ON GREEN, GPI 5&6 ON => YELLOW

1

2

audio

signal

is

for output of

by a Menu Setting.

De-embedded Analog

available

Please refer

through the

Tally La mp

speaker

Audio

to 6-6 Embedded Audio Setup for more

by a Menu setting

signal

from

SDI. The

16ch Audio

Signal

detailed

output is

information.

3. Controls continued

3-4. Function Buttons for FUNCTION 1 and FUNCTION 2

Used to select the functions to be assigned to individual buttons F1 and F2 (front-panel buttons).

Selectable Functions:

Note:

1. H/V Delay On/Off

2. Blue Only-Grayscale On/Off

3. Audio Display On/Off

4. Pixel to Pixel On/Off

5. Anamorphic On/Off

6. Aspect

7. 1 : 1 Scan

8. Waveform Display

9. Time Code Display

10. Audio Mute On/Off

11. PaP On/Off

When the input modes are DVI, PC-RGB signal, the
following functions are not available:

1) H/V Delay

2) Gray (MONO)

3) MARKER

4. Display Status

This is used to confirm the operating status. Some functions are not supported, depending on the installed options.

Video Waveform

& Vectorscope

Display Left:

CH-1
CH-3
CH-5
CH-7

CH-9
CH-11
CH-13
CH-15

Closed Caption Display:

Time Code Display

Closed Caption !
High Quality & Multi Format LCD Monitor

Standard 608 (VANC, Transcoded, Line 21), 708 (SDI Digital)

12:20:50:19

Displays up to 16 channels(L/R each 8channels) of audio level by De-Embedded

of HD/SD-SDI’s serial Audio Signal.

Display Right:

CH-2
CH-4
CH-6
CH-8
CH-10
CH-12
CH-14
CH-16

13

4. Display Status continued

1. Audio Level Meter Display

Set “ON/OFF” and “ Position” from the Audio Level Display Menu.
On: Left (even channel), Right (odd channel), OFF : Hide Level Bar
Level Meter Position: Position audio display at the top or bottom of the screen.

2) Waveform Monitor/Vector Scope Display

Set “ON/OFF” and “Position” from the W-FORM/VECTOR Button WFM/Vector Position : Position
Waveform/Vector from Display Menu( Left Top, Right Top, Left Bottom, Right Bottom)
(These functions are available only in SDI, CVBS, S-Video, YPbPr Mode).

Display Position is can be toggled when Up( ) button is pressed.

3) Time Code Display (SDI Input Mode)

Set “ON/OFF” and “Position” from Display Menu Setup.
Time Code Position : Position Time Code at the top or bottom of the screen.

5. Input Select Menu

INPUT MODE DISPLAY

These buttons are used to select desired video input or
to convert the corresponding video input. Information for
selected input signal can be viewed for 3 seconds through
Mode Display Window displayed at the left top of the screen.

When Menu control is not ON, if user press Enter button, then
currently selected input information appears.

When changing the input signal, there is a possibility that the signal will not be detected,
or the mode indication may be incorrect, or the screen size may be displayed incorrectly.

14

6. Control and Use of OSD Menu

1. Press “MENU” button for OSD Display .

2. Press “ENTER” button after menu selection by using UP ( ) / DOWN ( ) buttons.

3. Adjust status on the selected item with ENTER and UP ( ) / DOWN ( ) buttons.

4. Move to previous menu by using MENU button;

5. Close the OSD screen by holding MENU continuously.

If there is no input signal or no detected signal, the menu might not be displayed.

If you set the menu with an unstable signal status, it may cause an error.

The MENU setting values depend on the input signal mode. Therefore, please check the
input mode at the bottom of the menu when changing settings.

6-1. Video Setup

•Brightness: Adjusts brightness

•Contrast: Adjusts contrast

•Chroma:Adjusts chroma

•Phase:Adjusts phase

•Sharpness:Adjusts sharpness (This function can be

controlled by VR control Knob on the front panel.)
Note: In PC-RGB Input Mode,

•RGBColorSet:Controls RGB Level in YPbPr,RGB,PC-

RGB input mode. Select Default or User Adjust

•NTSCSetup:Select 0 IRE or 7.5 IRE. 7.5 IRE is used in

NTSC or YUV mode.

•AnalogLoop(Option): This function is only available

on products with the Loop Terminal. Set up On/Off

impedance of Analog Loop output terminals. Yes ->using
Loop output. No -> Not using Loop output.

When Loop terminal is not used, select Analog Loop ‘No’

15

6. Control and Use of OSD Menu continued

6-1-1. VIDEO (PC-RGB Mode) Setup

This Menu is displayed when selecting Auto Color Adjust
as User Adjust in YPbPr, RGB, PC-RGB Input Mode

•RedGain:Controls Gain of Read Input

•GreenGain:Controls Gain of Green Input

•BlueGain: Controls Gain of Blue Input.

•RedBias,GreenBias,BlueBias: Controls Offset

of each Bias

•AutoColorBalance: Selects RGB auto set of Gain , Bias.

6-2. DISPLAY Setup

Sets Screen size mode or display status.

•Aspect:Sets picture ratio as 16 :9 or as Native ratio in SD

mode , 2K mode.

•1:1Scan:

ON -> Operates display at input Pixel size in SD mode.
(Not available in HD Mode)
OFF -> Scales display to LCD size in SD mode.

•Anamorphic: Makes vertical resize to see Anamorphic

screen(2.35:1) on 720/50P 59.94P mode.

•PaPMain:Selects input of left (main) screen from PaP

(Picture and Picture) mode. Any Input signal can be

selected.(SDI1,2,CVBS1,2,3, S-VIDEO, YPbPr, RGB,PC­RGB,DVI)

•PaPSub:Selects input of right (sub) screen from PaP

(Picture and Picture) mode. Selectable sub source is
automatically changed depending on Main Source.

PaP Main PaP Sub

16

6. Control and Use of OSD Menu continued

6-2-1. DISPLAY (PC-RGB)

•WFM&VectorPosition: Display’s input signal as a format of waveform on the screen .

Display Position: locates the Waveform & vector scope Position

Display Position can be located in any of the four corner.

This is displayed when PC-RGB signal is selected.

•PCSCAN: Set output status as Fill or Aspect mode.

•V.Position: Adjust vertical position of screen for PC mode

input.

•H.Position: Adjust horizontal position of screen for PC

mode input.

•Phase: Adjust digital sampling phase of SC of input signal

(VGA mode).

•Clock: Used to adjust digital sample clock in PC-RGB

mode. (VGA)

•AUTOAdjust: Used to adjust the best display position

automatically in PC-RGB mode. (VGA)

•PaPMain,PaPSub(Option): Select input of right (Main) /

left (Sub) screen in PaP mode.

Display Position:

Left Upper, Right Upper, Left Bottom,
Right Bottom

Vector

Waveform

•VectorColor75%/100%:

Sets Input Color Reference Level in Vector Display.
Depending on 100% or 75%, Color, Marker position is changed.

•TimeCodeDisplay(Option):Displays Time Code on the screen in HD/SD-SDI signal input

•PixeltoPixel(Option): This displays native input HD-SDI signal, 1920 x 1080 without scaling down. The

active display can be set to Left Upper, Right Upper, Left Bottom, Right Bottom, and Center.

Depending on the screen size & input signal resolution, pixel to pixel indicator moves as follows.

Shift ( ) button

17

6. Control and Use of OSD Menu continued

6-3. COLOR Setup

•ColorTemperature: Set the color temperature or White

Balance on screen among VAR 3200°K, 5400°K,
6500°K, 9300°K, USER.

•VARNumber-> Selectable in steps from 1 to 63 from

3000°K ~ 9300°K

•USER-> Controls each RGB Gain and Bias.

•R,G,BGain: Individually Controls R,G & B Gain in the

User Mode.

•R,G,BBias: Individually Controls R,G & B bias in the

User Mode

•Clock: Adjusts digital sample clock in PC-RGB mode

•AUTOAdjust: Adjusts the best display position

automatically in PC-RGB mode (VGA)

•PaPMain,PaPSub(Option): Selects main input in PaP

mode (left), Selects sub input in PaP. Please refer to
section 6-2 for detailed

Use professional probe (not included) to adjust Color Temperature (White Balance)
to precise adjustment.

Color matrix Parameters use ITU Standard color. EBU color is set assuming parameters for an LCD panel;

the best color is produced according to the standard for SDTV (ITU-R/BT.601) and HDTV (ITU-R/BT.709).

18

6. Control and Use of OSD Menu continued

6-4. MARKER Setup

•SafetyArea4:3:Selects the range of the Safe Area in 4: 3 SD mode.

95%, 93%, 90%, 88%, 85%, 80%, EBU Action 16:9, EBU Graphic 16:9, EBU Action 14:9, EBU Graphic

14:9,EBU Action 4:3, EBU Graphic 4:3,Off

•CenterMarker: Center Marker ON / OFF

•Marker16:9

Set the type of marker when the aspect ratio setting is
16 : 9 in HD signal.

•TypeofMarker

4:3,15:9,14:9,13:9,1.85:1,2.35:1, USER, Off

•SafetyArea16:9

Selects the size of the safe area in 16 : 9 HD screen.
95%, 93%, 90%, 88%, 85%, 80%, Off
EBU Action 16:9,EBU Graphic 16:9,
EBU Action 14:9,EBU Graphic 14:9,
EBU Action 4:3,EBU Graphic 4:3,Off

•MarkerColor:Selects Marker Color: White, Red, Green, Blue, Gray, Black

•MarkerBackColor: Sets background transparency among Normal, Half, and Grayscale excluding Safety area.

•MarkerThickness: Sets Marker Thickness as Pixel unit(1~10 pixel)

•UserMarkerH1: Set the vertical line of Marker (left side: refer to below picture)

•UserMarkerH2: Set the vertical line of Marker (right side)

•UserMarkerV1: Set the horizontal line of Marker (upper)

•UserMarkerV2:Set the horizontal line of Marker (lower)

Marker H1 Marker H2

Marker V1

Marker V2

19

6. Control and Use of OSD Menu continued

6-5. OSD Setup

•ClosedCaption: This function is available in Composite, YPbPr and Digital (HD/SD-SDI) signal.

There are three selectable mode : OFF, CC 708, CC 608 (Transcoded, VANC, Line 21)
This function displays character information included in CC signal on the screen.

•Status/MenuDisplayTime

Sets Menu and Information.

Select one of off, 0(continute)~60 seconds.

•Status/MenuBlend

Set transparency of menus and Indication windows on

the screen Selects 0~15 levels

•MenuPosition

Select for Center, Left Top, Right Top, Left Bottom,
Right Bottom.

•InternalPattern: Without additional Input signal, it provides internal Test Pattern of 1920 x1080 30p format

on the screen. (Off, Blue, Green, Red, 0~100% White)

•SourceIDDisplay: User can enter Monitor ID on the screen.

•SourceIDCharacter:User can enter Source (Monitor) ID which is displayed on the Monitor.

Up to 10 digits writable.

•SourceIDPosition: Sets ID display position (Left-Top, Left-Bottom, Right-Top, Right-Bottom, Center)

Menu Position: Left-Top, Left-Bottom, Right-Top, Right-Bottom, Center

Closed Caption !
High Quality & Multi Format LCD Monitor

CAMERA 1

Source ID

Closed Caption Display: Standard 608 (VANC, Transcoded, Line 21),

708(SDI Digital)

When Loop terminal is not used, select Analog Loop ‘No’.

20

6. Control and Use of OSD Menu continued

6-6. AUDIO Setup

•EmbeddedAudio(L):Select Digital Audio (L) output from

1 to 16 channels when using SDI input.

•EmbeddedAudio(R): Select Digital Audio (R) output from

1 to 16 channels when using SDI input.

•AudioLevelMeter: Select ON/OFF for the function which

can display the SDI Embedded Audio signal level on a
Level Meter on the screen.

•LevelMeterPosition: Select position of Audio Level

Meter as Upper/Lower screen.

•SpeakerSource(Option): Select Speaker between Line

(external input) and SDI (De-embedded).

•SpeakerOutput(Option): Select Speaker output status

among L, R, L/R (stereo)

•SpeakerVolume(Option): Select Speaker output level.

6-7. GPI Setup

Speaker setting menu is used only when the speaker option is present.

•GPIControl:Select external control ON/OFF. It is not

possible to control with Remote terminal when it is OFF.

•GPIPort1,2,3,4,5,6,7: Assign each GPI Port of external

Remote Control Terminal (RJ-45). Double function for

each port is prohibited. Please refer to section 8-1,2,3
for detailed information.

GPI Port 7 is fixed at Standby.

•RemoteIDNumber: Set the number when controlling IR

remote controller (Option).

•SerialRemote: Select whether to use external Serial Port

control or not. Front Key and IR remote control will be
unavailable when Serial Remote is ON.

To terminate Serial Remote status (Update, Remote ON): Press Menu button for 3 sec.

21

6. Control and Use of OSD Menu continued

6-8. SYSTEM Setup

To terminate Update Firmware status:

Press Menu button for 3 sec.

•Function1,2:Select the functions to be assigned to

individual buttons F1 and F2. Please refer to section 3-4
for detailed information.

•BackLight: Adjust brightness of LCD Panel.

•FANMotor: Sets ON/Off internal Fan motor. Only available

in 17” model.

•FrontButtonLED: Sets ON/OFF front LED

•UpdateFirmware: Used to update system software

•SetupLoad: This is used to make a group change of the

function values which have been set.

•Factory: To return to the factory default.

•User1,2,3: Menu setting is transferred to the Menu of

1,2,3 to be saved by user.

•SetupSave: Save current menu setting into one of USER

1,2,3. USER 1,2,3 can be recalled by Setup Load.

•FirmwareVersion: System software version.

•OperatingTime: Product operating time

Note: While Back Light is adjusted, LCD panel requires enough time to be stable adjusting

Phase (brightness). It requires more than 30 minutes

7. Program Update Port

7-1. Program Update Port (RJ-11)

Update Port(RJ-11) can be used in a situation as below.

1) To modify Firmware program

2) To control Color Temperature, Gamma Setting for LCD

3) To control Multi Monitors using PC Exclusive use program “Wall System Control” on PC

1 2 3 4 5 6

1 PIN NC 4 PIN GND

2 PIN RX+ 5 PIN TX+

3 PIN RX- 6 PIN TX-

Update Terminal Assignment

Update (RJ-11)

Please consult with technician for Program Update or for Serial Port use. Incorrect use of this
port may cause damage or malfunction.

22

7. Program Update Port continued

7-2. Multi Monitor Control (through Update Port)

Multi Monitor Control can be operated by professional Adaptor (RS-232C - Serial Conversion) Converting
device and by PC where exclusive use program (Wall System Controller) is installed. (Optional)

PC (Control S/W)

Adaptor (RS-232C <-> Serial Data) Converting Device

8. Remote Terminal Assignment

8-1. Remote Terminal (RJ-45) Assignment

Each terminal function can be set from the GPI CONTROL SETUP Menu.

1 2 3 4 5 6 7 8

Remote PIN Assignment

1 PIN GPI Port 1 5 PIN GPI Port 5

2 PIN GPI Port 2 6 PIN GPI Port 6

3 PIN GPI Port 3 7 PIN GPI Port 7

(Stand by/Power ON/OFF)

4 PIN GPI Port 4 8 PIN COMMON (GND)

Remote (RJ-45)

8-2. How to connect GPI Port (RJ-11)

For each port designation, please refer to GPI & REMOTE Menu.

Connecting Method is as belows.

Control Terminal: 1 ~ 7 Pin

Contact Point Switch

It is possible to attach
pin one by one.

GND Terminal: 8 Pin of RJ-45

Please refer to section. 8-3. Remote Terminal Assignment.

23

8. Remote Terminal Assignment continued

8-3. Remote Terminal Assignment (GPI Port)

Port Assignment Items Function Operating conditions

CVBS1 Input Switches the input CVBS1

CVBS2 Input Switches the input CVBS2

CVBS3 Input Switches the input CVBS3

SDI1 Input Switches the input SDI-1

SDI2 Input Switches the input SDI-2 (except for 7”)

DVI Input Switches the input DVI

HDMI Switches the input HDMI (except for7”)

VGA Input Switches the input PC-RGB

Y/Pb/Pr Input Switches the input YUV

RGB Input Switches the input RGB

S-Video Input Switches the input Y/C

Audio Display on, off Switches Audio Level ON/OFF Edge operation

Waveform Display On/Off Switches Waveform ON/OFF

Pixel to Pixel on, off Switches Pixel to Pixel ON/OFF.

Anamorphic on, off Switches Anamorphic ON/OFF

Tally Red on, off Switches Red LED ON/OFF of Tally Lamp Level Operation

Tally Green on, off Switches Green LED ON/OFF of Tally Lamp (Connected: ON, Open: Off)

Grayscale on/off Switches Mono ON/OFF

Blue Only on/off Switches Blue Only ON/OFF

MARKER 16:9 Selects Marker 16:9 Mode

MARKER on/off Switches Marker ON/OFF

SD Aspect on/off Switches SD Aspect ON/OFF

1:1 SCAN on/off Switches 1:1 SCAN Function ON/OFF

Center Marker on/off Switches Center Marker ON/OFF

H/V Delay on/off Switches H/V Delay Function ON/OFF

Safety Area 16:9 Controls Safety Area in 16 :9. Edge operation

Safety Area 4:3 Controls Safety Area in 4 :93

SCAN Selects Screen Size as shown in the front button

KEY-UP CURSOR UP during Menu Control.

KEY-DOWN CURSOR DOWN during Menu Control.

KEY- MENU Switches Menu ON/OFF.

KEY-ENTER Switches Enter Button ON/OFF

KEY-Standby Port 7 Fixed. (Stand by Power ON/OFF)

24

9. List of Compatible Signal Formats

9-1. Video Signals

Composite Component
No Input Signal Formats Video

1 NTSC P - - - - -

2 PAL P - - - - -

3 525/60i (SD) - P P P - -

4 625/50i (SD) - P P P - -

5 720*480/59.94p - P - - P P

6 720*576/50p - P - - P P

7 1280*720/23.98p - - - - - -

8 1280*720/24p - - - - - -

9 1280*720/50p - P - P P P

10 1280*720/59.94p - P - P P P

11 1280*720/60p - P - P P P

12 1920*1035/59.94i - - - P P P

13 1920*1035/60i - - - P P P

14 1920*1080/50i - P - P P P

15 1920*1080/59.94i - P - P P P

16 1920*1080/60i - P - P P P

17 1920*1080/23.98p - P - P P P

18 1920*1080/23.98psf - P - P - -

19 1920*1080/24p - P - P P P

20 1920*1080/24psf - P - P - -

21 1920*1080/25p - P - P P P

22 1920*1080/25psf - - - P - -

23 1920*1080/29.97p - P - P P P

24 1920*1080/29.97psf - - - - - -

25 1920*1080/30p - P - P P P

26 1920*1080/30psf - - - - - -

27 1920*1080/50p - P - - P -

28 1920*1080/59.94p - P - - P -

29 1920*1080/60p - P - - P -

30 2048*1080/23.98p - - - P - -

31 2048*1080/23.98psf - - - P - -

32 2048*1080/24p - - - P - -

33 2048*1080/24psf - - - P - -

Y,Pb,Pr R,G,B(SOG)

HD/SD-SDI DVI HDMI

• With Analog YPbPr mode, 1035/59.94i,60i signal input, Marker is displayed in 1080/59.94i,60i and output.

• Output screen mode can be output with automatic control in DVI mode.

• STATUS Display of Input Signal might be different with real screen.

• Safety Area Edge part may not be displayed in some modes.

25

9. List of Compatible Signal Formats continued

9-2. Computer Signal (PC-RGB/DVI)

No Input Signal Names Screen Resolution VGA (PC-RGB) DVI Vertical Frequency

1 VGA 640*480 P P 60Hz ~ 100Hz

2 SVGA 800*600 P P 56Hz ~ 85Hz

3 XGA 1024*768 P P 86Hz ~ 100Hz

4 WXGA 1280*768 P P 50Hz ~ 85Hz

5 SXGA 1280*1024 P P 60Hz ~ 76Hz

6 WSXGA+ 1680*1050 P P 50Hz~60Hz

7 UXGA 1600*1200 P P 60Hz Only

8 WUXGA* 1920*1080 P P 60Hz

9 WUXGA 1920*1200 - P 60Hz,( PC Only)

26

10. Specifications

Function PBM-070/PBM-070X

INPUT HD/SD-SDI Input 1EA, HD/SD Serial Digital , 1.485G/270M ,BNC Jack

Analog Input 3EA,Composite,YC(S-Video),YPbPr,RGB,BNC Jack

PC-RGB(DVI) Input 1EA,DVI + Analog Jack (with gender) (24Pin + 5Pin)

DVI Input 1EA, DVI-I, 24pin, Female

OUTPUT SDI Output 1EA, BNC, Active Loop Output

ANALOG INPUT Composite (CVBS) 1.0Vp-p(with sync), NTSC/PAL

LEVEL YC(S-Video) Y :1.0Vp-p, C:0.286Vp-p

Component (Y/Pb/Pr) Y :1.0Vp-p, Pb :0.7Vp-p, Pr :0.7Vp-p

Component (R/G/B) G :1.0Vp-p(with Sync), B :0.7Vp-p, R :0.7Vp-p

DVI-RGB,Sync Level R, G, B : 0.7Vp-p, H/V Sync : 4V ± 1Vp-p

INPUT SIGNAL 2K Format 2048*1080,24p/psf,23.98p/psf

FORMAT SMPTE 274M 1920*1080i/60,59.94,50,24sf, 23.98sf

1920*1080p/30,29.97,25,24,23.98,

SMPTE 296M 1280*720p/60,59.94,50

SMPTE 260M 1920*1035i/60,59.94

SMPTE 259M,125M 720*480i/60,59.94

ITU R-BT.656 720*576i/50

Component 640 X 480 up to 1920 X 1080p

DVI Digital 640 X 480 up to 1920 X 1200

PC-RGB(DVI) Mode 640 X 480 up to 1280 X 1024, max 1600 X 1200

AUDIO INPUT Input 1EA, L/R, Stereo pin jack

SDI Audio Input Embedded HD/SD-SDI Audio

AUDIO OUTPUT Output 1EA, L/R, Stereo pin jack

Speaker Output 1EA, 1W

Output Signal Input Line & De-embedded Audio, 1~ 16CH

I/O PORT GPI Remote 1EA, Remote, RJ-45P Jack, GPI-7 Port

Serial Update 1EA, RJ-11P Jack, RS-422, Serial interface

LCD Size 7.0”(KF05)

Resolution 800 X 480

Pixel Pitch 0.1905 X 0.1905 mm

Color 16.7M

Viewing Angle (deg) R/L:130, U/D:110

Luminance of White 350 cd/m

Contrast 400 : 1

Display Area (H X V) 152.4 X 91.44 mm

POWER REQUIREMENTS DC 12V/5A

POWER CONSUMPTION 0.1 – 1A(12W)

OPERATING TEMPERATURE 0°C ~40°C (32°F~104°F)

WEIGHT 3 kg - 6.62 Lbs

Dimension (W*H*D) w/o Box & Stand 203 X 131 X 52 mm

8 X 5.16 X 2.05 Inch

ACCESSORY Power Cord, Manual, DVI to VGA Gender, Desk Stand, Tripod adaptor

OPTION Rack Mount, Hood & Carrying Case, Sunviser, Tripod Mount

27

12. Product Dimensions

Battery Pack
V-Mount Hole

9.47”

7.99”

2.04”

12.2”

12.87”

2.71”

VESA Mounting Hole
(75*75mm)
Size M4, Depth 10mm

PBM-070/PBM-070X

unit: mm & inches

28

13. Troubleshooting

r

r

r

Solutions
the problem, unplug the monitor and consult an

No.

1

No

2

No picture with the power on

3

No

4

Wrong color, no

5

Wrong picture position, wrong picture

6

Menu does not

14.

•

When a still image
characteristics of the LCD

•

Random
The
affected by each other or by lighting.

•

Periodic maintenance inspection

•

Periodic maintenance inspection

to common problems

related

to the monitor are described here. If none of the

Authorized Dealer

Symptom P

power

sound

color

size

appear

on the

screen

or it is shaking

Maintenance

fixed color dots (“stuck

LCD

display

is

displayed

is built with

for a long time, it may appear

display

pixels”)

very

and is not a

high

precision technology. However,

on the

malfunction.

panel surface

time of backlight is about 50,000 hours.

time of fan motor

15. Update and Modification of Product

Specifications

of this product may be changed without prior notice.

solutions presented

or

Service

obable cause and co

•

Firmly

insert the Power

•

Check the DC power adaptor. (100V ~220V to 12VDC)

•

Connect

•

Turn on the power of the

•

Check

•

Connect

•

Adjust Volume

•

Check

•

Check

•

Check

•

Adjust the picture size

•

Items which are not available for the current input or the current

are not

•

Check

the signal cable firmly.

if

the input signal format is

the signal cable firmly.

Level.

if

the Hue is set up with basic value from the

if

the color

if

Pixel to Pixel mode is

displayed

if

the input signal format is

temperature

on the menu.

incorrectly

Power cycle the monitor, and the

are a

normal characteristic

(option)

is about 10,000 hours.

Center.

ective action

Cord.

connected component

acceptable

is in basic

on.

(H/V

due to

be

aware

Position)

Change

acceptable

heating

that a few

and set the

to the

monitor

menu.

value.

input or the input signal.

for the monitor

on the

screen. This

image

will reset.

of LCD

displays.

very small

pixels may be

here solves

output correctly.

.

input signal

.

is due to the

29

Notes

Plura Broadcast, Inc. - West Coast

2033 W. North Lane
Phoenix, AZ 85021
Tel: [phone]
Fax: [phone]

www.plurabroadcast.com

Plura Broadcast, Inc. - East Coast

67 Grand Avenue
Masapequa, NY 11758
Tel: [phone]
Fax: [phone]

PLURAPBM070MV0309