Plasmon LF 8600 User Manual

THE PLASMON 8000 SERIES
LF 8600 AUTOLOADER
USER MANUAL
P/N 97663032 A
Storing More Of Your Digital World ™. Permanently.
Reproduction of this manual, or any portion of this manual, is prohibited without the express permission of Plasmon Laser Magnetic Storage (LMS). Plasmon LMS reserves the right to make changes in this document and the product referred to herein without prior notice.
© 2000 Plasmon Laser Magnetic Storage
WARNING
Always observe the following when installing, operating or maintaining this product:
This unit must be connected to a power distribution system that has a
direct connection to earth ground (Terminated Terra [TT] network/ ground connected). This unit is not suitable for use on a floating ground (Interrupted Terra [IT]) network.
The AC input power cord must be shielded and must have a minimum
current rating of 10 A with a nominal cross-section area of 0.75 sq mm (reference: AWG #18) per conductor, 2 wires plus ground and product safety approvals as required for use in the country in which the unit is installed.
When the unit is mounted in an equipment rack or cabinet, be certain
that the internal temperature within the rack or cabinet does not exceed the limits defined in the Product Specification or this document.
To ensure the integrity of safety features of this unit, maintenance must
be performed only by qualified service personnel using designated Plasmon LMS parts.
In case of fire or other emergency, isolate the units from the main
power by disconnecting the power plugs from their site power receptacles. In situations where disconnecting the plugs is not possible or practical, use the system main power disconnect to isolate the units from the main power.
To prevent fire or shock hazard, do not expose this unit to rain or
moisture. Refer servicing to qualified technicians.
(German Translation)
Bei der Installation, Bedienung und Wartung dieses Produkts, bitte immer die folgenden Vorsichtsmaßnahmen treffen:
Dieses Gerät muß an ein Stromversorgungssystem angeschlossen
werden, das direkt mit einem Erdungsanschluß verbunden ist (Terminated- Terra-Netz [TT]/mit Erdanschluß). Dieses Gerät kann nicht an ein ungeerdetes Netz (Interrupted Terra [IT]) angeschlossen werden.
Die Verbindungsschnur des Wechselstromeingangs muß entstört sein
und ihr Minimalstrom unter folgenden Bedingungen bei 10 A liegen: Der Nennquerschnitt beträgt 0,75 mm je Leiter (Referenz: American Wire Gauge Nr. 18), es bestehen 2 Drähte plus ein Erdanschluß und das Produkt entspricht den im Land, in dem es aufgestellt wird, geltenden Sicherheitsvorschriften.
WARNING
Wird das Gerät in ein Gerätegestell oder einen Geräteschrank
eingebaut, ist darauf zu achten, daß die interne Temperatur im Gestell oder Schrank nicht über die in den Produktspezifikationen oder diesem Dokument angegebenen Grenzwerte hinausgeht.
Um ein ordnungsgemäßes Funktionieren der Sicherheitsmerkmale
dieses Gerätes zu gewährleisten, dürfen Wartungsarbeiten nur von qualifiziertem Fachpersonal ausgeführt werden. Es sind darüber hinaus nur Ersatzteile zu verwenden, die von der Firma Plasmon LMS angegeben werden.
Im Falle eines Feuers oder in einem anderen Notfall sind die Geräte
vom Hauptnetz zu trennen, indem die Netzstecker aus den Steckdosen am Einbauort gezogen werden. Ist ein Herausziehen der Stecker nicht möglich oder zu umständlich, trennen Sie die Geräte mit Hilfe des System- Hauptnetzabschalters vom Hauptnetz.
Um Feuer- oder Stromschlaggefahr zu vermeiden, ist dieses Gerät
niemals Regen oder Feuchtigkeit auszusetzen. Wartungsarbeiten sind qualifiziertem technischen Personal zu überlassen.
RADIO/TV INTERFERENCE (USA)
The information in this section applies only to units in use within the United States: This equipment generates and uses radio frequency energy and, if not installed and used properly, that is,
in strict accordance with the manufacturer's instruction, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specifications of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
reorient the receiving antenna
relocate the equipment away from the receiver
plug the equipment into a different outlet so that equipment and receiver are on different
branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. A pamphlet by the FCC ‘How to Identify and Resolve Radio-TV Interference Problems' is available from the US Government Printing Office, Washington, D.C., 20402, Stock No. 044-000-00345-4.
CDRH COMPLIANCE
LF 8600 contains a Class 1 Laser Product. This product complies with 21CFR Chapter 1, Subchapter J, applicable at date of manufacture.
CANADIAN EMI COMPLIANCE
Canadian Department of Communications standards require that the following statement appear in operating manuals for any digital apparatus imported into Canada:
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
FRENCH TRANSLATION
Cet équipement digital ne dépasse pas les limites de la Classe A pour les interférences radioélectriques des systémes digitaux fixées par les Réglements concernant les Interférences Radioélectriques établis par le Ministére des Communications du Canada.
All Plasmon LMS products comply with the requirements of this standard.
Agency Compliance and Approval
For details on Agency Compliance and Approval refer to the LF 8600 Product Specification Manual.

TABLE OF CONTENTS

SCOPE 9
RELATED PUBLICATIONS 9
GENERAL DESCRIPTION 11 DRIVE CHARACTERISTICS 13
FRONT PANEL 14 REAR PANEL 14 DIMENSIONS AND WEIGHT 15
SHIPPING WEIGHT 15 TEMPERATURE, HUMIDITY AND ALTITUDE 16 MEDIA ENVIRONMENTAL CHARACTERISTICS 17 SHOCK AND VIBRATION 17 AC POWER REQUIREMENTS 18 AC GROUND 18 AC POWER CORD 18 POWER SUPPLY OUT-OF-RANGE PROTECTION FEATURES 18 TILT RANGE 18 HEAT DISSIPATION 19 PARTICULATE LIMITS 19 WARNING LABELS 19
UNPACKING AND REPACKING INSTRUCTIONS 21
UNPACKING THE TOWER CONFIGURATION 21 UNPACKING THE RACK MOUNT CONFIGURATION 24 INSPECTING THE LF 8600 26 REPACKING THE LF 8600 26
CLOSING THE BASEPLATES 27 REPACKING THE TOWER CONFIGURATION 28 REPACKING THE RACK MOUNT CONFIGURATION 29
INSTALLATION AND DE-INSTALLATION 31
INSTALLATION REQUIREMENTS 31 TOWER INSTALLATION 32 RACK MOUNT INSTALLATION 33 SCSI BUS CONSIDERATIONS 46
CONNECTING POWER AND SCSI CABLES 48
CONNECTING THE POWER CORD 48
CONNECTING MULTIPLE DEVICES 49
CONNECTING A SINGLE DEVICE 50 CONNECTOR VERIFICATION 51 RACK MOUNT CONFIGURATION DE-INSTALLATION 51
OPERATING INSTRUCTIONS 55
CONTROLS AND INDICATORS 55 POWER-ON PROCEDURE 56 MODES OF OPERATION 7
OPERATING MODE 57
CONFIGURATION MODE 59
TEST MODE 81 MEDIA CARTRIDGE HANDLING 82
SETTING THE WRITE PROTECTION SWITCH 84
AFFIXING LABELS 85
MEDIA INSERTION AND REMOVAL 85
MANUAL CARTRIDGE RELEASE MECHANISM 89
MEDIA LOADING 93
OPERATOR MAINTENANCE 95
INSPECTING AND CLEANING FAN AND BLOWER FILTERS 95 REPLACING FUSES 96 MEDIA CLEANING 98
MEDIA CLEANING USING CLEANING KIT P/N 97662550 98
APPENDIX A 99
GERMAN TRANSLATIONS/ÜBERSETZUNGEN INS DEUTSCHE 99

SCOPE

This User Manual describes unpacking, installing, operating, and maintaining the Plasmon LF 8600 RapidChanger High-Performance Optical Disk Drive.

RELATED PUBLICATIONS

Publication Part Number
LD 8100/LF 8120/LF 8600/LF 8602 Product Specification 97663035 LD 8100/LF 8120/LF 8600/ LF8602 SCSI Interface Specification 97662164 LF 8600/LF 8602 Hardware Maintenance Manual 97653082
WARRANTY STATEMENT
The LF 8600 is warranted as stated in the purchase agreement between Plasmon and it’s customer, or the Plasmon sales order acknowledgment, whichever is applicable. The Plasmon LMS quality system is in compliance and registered to ISO 9001. The LF 8600 is manufactured from new parts, or remanufactured parts.
LF 8600 warranty does not cover defects or damage caused by the use of unauthorized parts or repairs or improper use or maintenance. Repairs or replacements not covered by the warranty will be invoiced at LMS’ then current prices.
The warranty is void when installation, service or repairs are performed by unauthorized personnel; when the product is affected by unauthorized alterations, modifications or other tampering or misuse; when the product is incorporated into a system which causes or involves any changes in the physical, mechanical or electrical arrangement of the product; or when the product is not used in accordance with its applicable specifications.
The term, authorized personnel, is defined as those persons who have been trained by Plasmon LMS Technical Services.
97663032 A
Page 9
PLASMON L M S - LF 8600 USER MANUAL Page 10

GENERAL DESCRIPTION

The LF 8600 RapidChanger is a write once read many (WORM), high-capacity optical disk drive with an integral shuttle capable of holding up to six LM 8000/LM 6000/LM 4000 media cartridges. The integral shuttle moves laterally to position one of six media cartridges for automated loading and unloading into the optical drive. The LF 8600 RapidChanger provides up to 30 GBytes of online storage or up to 180 GBytes nearline storage.
The LF 8600 is available in either a Rack Mount or Tower configuration. Two LF 8600 Rack Mount drives can be mounted side-by-side in an EIA standard 19-inch rack. The Tower is a standalone LF 8600 that can be located on an open floor or beside a desk.
LF 8600 RACK MOUNT CONFIGURATION
LF 8600 TOWER CONFIGURATION
Figure 1. LF 8600 Configurations
A Drive Operator Console (DOC) located on the front panel of the drive provides user control of drive operation and configuration as explained in the operator section of this manual. Operating messages are presented on the alphanumeric display in English, French or German. The language used is selectable. The front panel includes a lockable media access door to provide operator access to the shuttle and media cartridges.
The Auxiliary Diagnostic Port (ADP), located on the rear panel of each drive, can be used to download updates to the drive firmware in the field. Refer to the LD 8100/LF 8120/LF 8600/LF 8602 Product Specification (P/N 97663035) for more information.
97663032 A
Page 11
The LF 8600 supports a maximum sustained read and write transfer rate of 6.0 MBytes/sec without data verification. The drive will also support a 2.4 MBytes/sec write transfer rate with error correction and defect management to maintain data integrity and manage media flaws.
The LF 8600 implements the Small Computer System Interface (SCSI) via standard SCSI-2 micro­connectors located on the rear panel. Single-ended and differential interface options are available, and the interface can be changed in the field. Both the single-ended and differential controllers support asynchronous or synchronous data transfer operations.
Preventive maintenance for the LF 8600 is minimal (refer to Operator Maintenance section of this manual). Corrective maintenance is simplified by internal diagnostic firmware which detects, isolates and reports malfunctions to the operator and identifies the Field Replaceable Unit (FRU).
LM 8000 media is interchangeable between the LD 8100, LF 8120, LF 8600, and the LF 8602. The LF 8600 can also read LM 6000 and LM 4000 media. Contact Plasmon LMS for availability and ordering information for the LM 4000 media option.
PLASMON L M S - LF 8600 USER MANUAL Page 12

DRIVE CHARACTERISTICS

The LF 8600 Rack Mount and Tower configurations use the same major assemblies (refer to the next two figures).
LF 8600 CONFIGURATION
LF 8600 TOWER CONFIGURATION
22.86 CM (9.00 IN)
74.86 CM (29.47 IN)
54.65 CM (21.52 IN)
33.15 CM (13.05 IN)
Figure 2. LF 8600 Dimensional Details
97663032 A
Page 13

FRONT PANEL

The LF 8600 front panel (see figure below) includes a Drive Operator Console (DOC), media access door, and door lock within a bezel assembly. Refer to the Operating Instruction section of this manual for a detailed description of the DOC.
LF 8600 Front Panel

REAR PANEL

The LF 8600 rear panel contains the power switch along with AC power connector and fuses, the ground connector, and external interface connectors.
AUXILLIARY DIAGNOSTIC PORT (ADP)
DOC
BEZEL
MEDIA ACCESS
DOOR
KEY LOCK
SCSI-2 I/O CONNECTORS
LF 8600 Rear Panel
MANUAL RELEASE ACCESS HOLES
Figure 3. LF 8600 Panel Layout
PLASMON L M S - LF 8600 USER MANUAL Page 14
BLOWER GRILL AND FILTER ELEMENT
FAN GRILL AND FILTER ELEMENT
AC POWER SWITCH
AC POWER RECEPTACLE
THREADED GROUND CONNECTOR

DIMENSIONS AND WEIGHT

The table below lists the reference dimensions of the LF 8600 configurations.
Table 1. Dimensions of the LF 8600 Configurations
DIMENTION RACK MOUNT TOWER
Length 71.1 cm (28.0 in)
74.4 cm (29.3 in ) with Bezel
82.0 cm (32.3 in)
including Pedestal
Width 22.1 cm (8.7 in)
includes Bezel
Height 46.7 cm (18.2 in)
47.5 cm (18.7 in) with Bezel
Mounting Depth 71.1 cm (28.0 in)
35.7 cm (14.in)
including Pedestal
63.6 cm (25.0 in)
including Pedestal

SHIPPING WEIGHT

The LF 8600 shipping weight is listed below. These values do not include media cartridges.
Rack Mount: 44.1 kg (97 lbs) Tower: 62.3 kg (137 lbs)
The weight of one LM 8000 cartridge is approximately 1.18 kg (2.6 lbs).
97663032 A
Page 15

TEMPERATURE, HUMIDITY AND ALTITUDE

The following table lists the LF 8600 operating, storage and transit limits for temperature, humidity and altitude.
Table 2. Temperature, Humidity and Altitude Limits
CONDITION OPERATING NONOPERATING
Temperature
Maximum Rate of
10° to 42° C (50° to 108° F)
11° C/hr (20° F/hr) 20° C/hr (36° F/hr) 20° C/hr (36° F/hr)
2
-40° to 66° C
-40° to 151° F)
Change Humidity
10 to 90% 5 to 95% 5 to 95%
(Noncondensing Maximum Rate of
10%/hr 10%/hr 10%/hr
Change Maximum Wet Bulb
Temperature
3
Minimum Dew Point
Altitude
28° C (82° F) 46° C (115° F) 46° C (115° F)
2° C (35.6° F) 2° C (35.6° F) 2° C (35.6° F)
-300 to 3,000 m (-984 to 9,840 ft)
-300 to 3,000 m (-984 to 9840 ft)
STORAGE/TRANSIT
-40° to 66° C
-40° to 151° F)
Storage:
-300 to 3,000 m (-984 to 9,840 ft)
Transit:
-300 to 12,000 m (-984 to 40,000 ft)
1
1 Storage specifications are for 90 days maximum in Plasmon LMS packaging. No condensation is permitted. Transit specifi-
cations are based on a maximum 1-week period in a factory-sealed container.
2 Maximum operating temperature is 42 _C for a free-standing drive at sea level unless otherwise stated. Maximum operating
temperature is derated linearly above 300 m altitude to 38 _C at 2,000 m altitude.
3 See theLD 8100/LF 8120/LF 8600/LF 8602 Product Specification (P/N 97663035) for more information concerning the tem-
perature and humidity operating range.
PLASMON L M S - LF 8600 USER MANUAL Page 16

MEDIA ENVIRONMENTAL CHARACTERISTICS

The following table presents the LM 8000 Media environmental characteristics.
Table 3. Media Operation, Storage and Transportation Environments
OPERATION AND
SPECIFICATION
SHORT TERM
STORAGE
(2 years maximum)
Temperature 10°C to 47°C
50°F to 116.6°F
TRANSPORTATION
(2 weeks maximum)
-20°C to +55°C
-4.0°F to 131.o°F
LONG TERM
STORAGE
10°C to 30°C 50°F to 86.0°F
Relative Humidity (no condensation)
Wet Bulb Temperature 26°C max. (78.8°F) 26°C max. (78.8°F) 26°C max. (78.8°F) Temperature Gradient 10°C/hr max.
Air Pressure N/A N/A N/A Solar Radiation N/A Case to be kept closed Not to be stored in direct
5% - 80% 5% - 90% 5% - 80%
(18.0°F/hr max.)
31°C/hr max. (55.8°F/hr max.)
5°C/hr max. (9.0°F/hr max.)
sunlight

SHOCK AND VIBRATION

The following table lists the conditions and limits for shock and vibration.
Table 4. Shock and Vibration Criteria and Limits
CONDITION OPERATING
Swept Vibration (Bidirectional) 1 Octave/Min
3
Shock (Host Retries May Be Required and Drive Performance May Degrade During Test
5 to 250 Hz 0.1 g Peak, 250 to 500 Hz
0.25 g Peak
10 - msec Half Sine Pulse of 2.5 g Peak, with pulses applied every 3 sec
NONOPERATING
5 to 44 Hz, 0.03 in Double Amplitude, 44 to 500 Hz
3.0 g Peak
1
STORAGE/TRANSIT
5 to 44 Hz, 0.03 in Double Amplitude, 44 to 500 Hz
3.0 g Peak
2
Unpacked (3 Axis) 5 - msec Half Sine
Pulse of 20 g Peak
Packed on Pallet 46 - cm (18 - in)
Drop Test Flat
1 With media removed. 2 In LMS - approved packaging. 3 Shock repetition rate should be limited to allow mechanical system transients to subside between pulses.
97663032 A
Page 17

AC POWER REQUIREMENTS

The LF 8600 has a grounded power connector integrated into the AC power switch. Over current protection is provided by two fuses integrated into the AC power switch. Two spare fuses are included within the power connector. Refer to the Operator Maintenance section for the fuse replacement procedure.
The drive's power supply accepts the input line voltages listed in the table below. The power supply is auto ranging and does not require mechanical switching for input voltage or frequency selection.
Table 5. AC Power Requirements
AC LINE
VOLTAGE
95.0V TO 128V 1.4A / 110W 10A
173.0 TO 269V 0.7 / 110W 5A 1.0A / 160W 15A
1
This current measurement determines the stated power and maximum heat dissipation of the Drive (546 BTU/hr) based on RMS
current over the 10S cycle derated by the Power Factor. It also determines the 2.0 A UL plate rating.
READY
SURGE PEAK
<1s
(SPIN-UP)
READY + 1 SPIN-UP/DN
CYCLE EVERY 10 s
2.0A / 160W
(1)
MIN
SERVICE
RATING
15A

AC GROUND

The LF 8600 chassis should be connected to earth ground for operator safety. The AC power cord has a grounding conductor which connects the LF 8600 chassis to safety ground through the site AC power system. If the site AC system ties its ground wire connection to earth ground, then the LF 8600 chassis will also be tied to earth ground. All site AC power connections must be maintained on the same safety ground.
A line grounding connector located on the rear panel can also be used to tie the LF 8600 chassis to earth ground. This ground connector is a 6-mm (0.24-in.) M4 with a nut and lock washer.

AC POWER CORD

The type of AC power cord supplied with the LF 8600 will depend upon the configuration ordered.

POWER SUPPLY OUT-OF-RANGE PROTECTION FEATURES

The LF 8600 power supply provides over and under voltage protection, over current protection, and power failure detection. Should an out-of-range condition be detected, the LF 8600 will shut down the DC outputs of the power supply. After the situation is corrected, power can be restored by turning the AC power switch to the OFF position and then to the ON position again.
PLASMON L M S - LF 8600 USER MANUAL Page 18

TILT RANGE

The LF 8600 is not designed for use when tilted from the vertical position.

HEAT DISSIPATION

The drive will typically present a heat load of 95 kg-calories/hr (376 BTU/hr) during a read/write operation. When media cartridges are inserted, loaded, spun up, spun down, unloaded and removed at the drive's maximum rate, the LF 8600 will typically present a heat load of 138 kg-calories/hr (546 BTU/hr).

PARTICULATE LIMITS

The LF 8600 is designed for use in an office or computer room. The environment must have a low dust level. The LF 8600 filters incoming air for cooling to reduce the quantity of particles entering the drive; however, the filter is not effective against small particles (including tobacco smoke) which will become deposited on optical components and media, causing degradation in drive performance. Refer to the Operator Maintenance section for media cleaning and air filter cleaning instructions.

WARNING LABELS

The LF 8600 is classified as a laser product and meets all United States federal requirements. The warning labels shown in the figure below have been applied to the Drive to ensure compliance with federal regulations and must not be removed from the LF 8600.
LASER DANGER LABEL
Figure 4. Location of LF 8600 Warning Labels
LASER CLASS LABEL
CANADIAN CLASS A LABEL
FCC, RFI, CLASS A LABEL
97663032 A
Page 19
PLASMON L M S - LF 8600 USER MANUAL Page 20
UNPACKING AND REPACKING
INSTRUCTIONS
The LF 8600 is shipped with foam packing material which protects the unit from shock and vibration. When you receive your LF 8600, inspect the shipping carton for damage before unpacking the unit to substantiate a claim with the carrier if the unit is damaged. Retain all original packing materials for possible reshipment.
WARNING
The LF 8600 must be unpacked, repacked and transported by two persons. Physical injury can result if one person attempts to lift the LF 8600. A wheeled cartis recommended for transporting the LF 8600 within a building. Precautions should be taken to guard against sudden bumps and jarring.

UNPACKING THE TOWER CONFIGURATION

The LF 8600 is packaged as illustrated in the next figure. The top, bottom and sides of the LF 8600 are protected from shock and vibration by foam cushions. The top cushions are also used to hold the accessories box (inner box) which is placed between the blocks of foam.
To unpack the unit:
1. Move the carton to the installation site. Unpacking the carton at the installation site minimizes the effects of vibration and shock.
2. Cut the tape and straps that secure the top of the box. Do not allow the cutting blade to penetrate into the carton.
3. Carefully lift the outer corrugated carton up and remove it while supporting the inner hinged wooden ramp. When the carton is removed, lower the ramp to the floor and remove the front foam cushion.
4. Remove the accessories box (inner carton) containing cables and documentation and the two foam cushions which support the box. Remove the ESD protective packing material.
97663032 A
Page 21
OUTER CARTON
INSERT
INNER CARTON
INSERT
REAR FOAM CUSHION
ESD PROTECTIVE PACKING MATERIAL
FRONT FOAM CUSHION
LF6600
PALLET CUSHION
HINGED RAMP
FOAM INSERT LOCATED BETWEEN SHUTTLE AND FRAME OF THE DRIVE
CASTER SUPPORT
PALLET
EP004566
Figure 5. LF 8600 Tower Packing
PLASMON L M S - LF 8600 USER MANUAL Page 22
5. Ensure that the casters are locked. Lift the front end of the LF 8600 high enough to remove the pallet cushion and then lower the LF 8600 onto its casters.
6. Unlock the casters and roll the LF 8600 down the ramp to its installation location. Precautions should be taken to avoid sudden bumps and jarring.
7. Lock the casters once you have the LF 8600 situated at its installation location.
UNLOCKED
LOCKED
Figure 6. Caster for the LF 8600 Tower
8. Open the media access door and remove the foam insert. Manually move shuttle all the way to the right to the home position.
Figure 7. Moving the Shuttle to the Home Position
97663032 A
Page 23

UNPACKING THE RACK MOUNT CONFIGURATION

To unpack the LF 8600 Rack Mount configuration, refer to the next figure and perform the following procedure:
1. Move the carton to the installation site. Unpacking the carton at the installation site minimizes the effects of vibration and shock.
2. Cut the tape that secures the top of the box. Do not allow the cutting blade to penetrate into the carton.
3. Carefully lift the outer corrugated carton up and remove it.
4. Remove the accessories box (inner carton) containing cables and documentation, and remove the ESD protective packing material.
5. Remove the two cushions which support the accessories box (inner carton).
6. Carefully lift and remove the LF 8600 from the shipping carton and place it on a flat surface capable of supporting 48 kg (106 lbs). A wheeled cart is recommended for transporting the LF 8600 within a building. Precautions should be taken to avoid sudden bumps and jarring.
CAUTION
The bezel is slightly larger than the chassis. When placing the drive onto a flat surface, allow the front end of the LF 8600 to extend over the edge of the supporting surface so that the bezel does not bear any weight.
7. Open the media access door and remove the foam insert. Manually move the shuttle all the way to the right to the home shuttle position.
PLASMON L M S - LF 8600 USER MANUAL Page 24
INSERT
INNER
CARTON
OUTER CARTON
INSERT
REAR FOAM CUSHION
ESD PROTECTIVE PACKING MATERIAL
FRONT
FOAM
CUSHION
PALLET
FOAM INSERT LOCATED BETWEEN SHUTTLE AND DRIVE FRAME
LF 8600
Figure 8. LF 8600 Rack Mount Packing
97663032 A
Page 25

INSPECTING THE LF 8600

The following items should be included in the LF 8600 carton:
one LF 8600 with Bezel assembly (Tower comes completely assembled)
one AC power cable
one User Manual
one combination manual baseplate/door lock release tool
I/O cables (optional)
terminators (optional)
The following optional items, if ordered, will have been shipped with the LF 8600 in separate cartons:
LM 8000 Media Cartridges
Rack Mount Installation Kit
Blank Panel Kit
After unpacking the LF 8600, check for:
damage to the chassis cover, chassis and bezel
damage to connectors
dislocated or broken controls and indicators
Report all discrepancies, missing items and damaged equipment to your supplier. If condensation exists on the drive, allow the moisture to evaporate by exposing the LF 8600 to the
operating environment for at least 6 hours before powering on the unit.

REPACKING THE LF 8600

The LF 8600 should be repacked using the original packing materials. Prior to packaging the LF 8600, close the baseplates as described in the next section. Repack the LF 8600 using the following procedure.
CAUTION
Shipping the LF 8600 without closing the baseplates may result in damage to the drive which is not covered under warranty.
PLASMON L M S - LF 8600 USER MANUAL Page 26

CLOSING THE BASEPLATES

1. Ensure that a cartridge is not inserted in the drive; if it is, unload the cartridge. Remove all cartridges from the shuttle. To remove cartridges from a drive that is not operational, follow the procedure below:
a.) Ensure that the AC Power switch is set to the OFF ( O ) position. b.) At the rear panel, insert the manual release tool into the upper access hole
and engage the recessed D-shaped shaft. Turn the tool handle clockwise as far as it will turn, closing the upper baseplate.
c.) Repeat step b) at the lower manual release access hole to close the lower baseplate.
2. Select the "Park Drive" option, as explained in the Operating Instruction section of this manual.
UPPER ACCESS HOLE
MANUAL RELEASE
TOOL
REAR PANEL
LOWER ACCESS HOLE
Figure 9. Manually Closing the Drive's Baseplates
EP006047
97663032 A
Page 27

REPACKING THE TOWER CONFIGURATION

1. Open the media access door.
2. Manually push the shuttle all the way to the left and insert the foam shipping block to hold it in place. Close the media access door.
3. Roll the LF 8600 up onto its shipping pallet and lock all four casters to prevent rolling.
4. Lift the front and rear of the LF 8600 high enough and place the caster support underneath the drive.
5. Raise the wooden ramp to the vertical position and place the pallet cushion between the ramp and the front panel of the LF 8600. Place the ESD protective packing material on top of the drive.
6. Place the two end cushions which hold the accessories box on the top front and rear of the LF
8600.
7. Place the power and interface cables, User Manual and other accessories into the options and accessories box and seal with tape. Place this box between the top end cushions.
8. Slip the corrugated shipping carton over the LF 8600 and the raised ramp, and lower the carton down to the top of the pallet.
9. Strap the carton to the pallet at each end.
PLASMON L M S - LF 8600 USER MANUAL Page 28

REPACKING THE RACK MOUNT CONFIGURATION

1. Open the media access door and manually move the shuttle all the way to the left.and insert the foam shipping block to hold it in place. Close the media access door.
2. Remove the LF 8600 chassis with its bezel from the Rack Mount configuration by reversing the procedure detailed in the Installation and De-installation section. The bezel extends below the chassis; ensure that you do not place the unit flat on a hard surface, thereby damaging the bezel.
3. Ensure that the lower packing material is positioned to form a rectangular frame for the LF 8600 chassis which opens to the front.
4. Place the bezel relief cushion on the pallet so that it will support the chassis just behind the bezel.
Figure 10. Moving the Shuttle Assembly to the Shipping Position
5. Place the LF 8600 into the foam frame so that the drive rests on the bezel relief cushion and the bezel bears no weight.
6. Place the lower front foam cushion between the carton and the front of the LF 8600. Place the ESD protective packing material on top of the drive.
97663032 A
Page 29
7. Position the two end cushions which hold the accessories box on the top front and rear of the LF 8600.
8. Place the power and interface cables, User Manual and other accessories into the options and accessories box and seal with tape. Place this box in between the foam end cushions.
9. Lower the upper sleeve down onto the lower carton and pallet and .Strap the carton to the pallet at each end.
PLASMON L M S - LF 8600 USER MANUAL Page 30
Loading...
+ 83 hidden pages