Plasma Air 600 Installation Manual

LOW MAINTENANCE

The PlasmaPURE 600 is designed for
continuous operation without requiring
replacement parts. It is recommended that the
device is mounted downstream of the filter to
ensure the carbon fiber brushes remain clean
over time.

Cleaning Interval:

The PlasmaPURE 600 was designed for low
maintenance. The device should be checked
semi-annually to confirm the brushes are clean
for maximum output. If the carbon fiber
brushes do get dirty, the instructions below
outline how to clean the device:

1. Disconnect power

2. Remove any accumulated dust on bristles of

the brushes with either compressed air or
a toothbrush.

3. Reconnect the power

SAFETY

When operating any electrical device, basic
precautions should always be followed for
safet y.

WARNING: Risk of electrical shock —
can cause injury. Disconnect unit from
the power supply before servicing.

Keep all wires away from the carbon
fiber brushes, allowing at least 1 inch of
spacing between the carbon fiber
brushes and anything metal or grounded.

Never touch ion needles while operating.

Do not connect power before installation
is complete. Always disconnect power to
the unit before handling any of the unit
components or servicing.

If device is not working properly,
call a customer service representative
at 1-203-662-0800

©2018 All rights reserved.

PA-RES-US-IOM-001

THREE YEAR WARRANTY

Plasma Air International hereby warrants to the
consumer that the product purchased under this
warranty be free from defects in material and
workmanship under normal use when installed,
operated and maintained in accordance with
manufacturer’s instructions.

In the event of a product defect, failure or
malfunction, Plasma Air will, for a period of three
(3) years from the date of purchase, repair or
replace at its discretion the defective, failed or
malfunctioning product purchased under this
Warranty. Installation and/or removal labor is not
covered under this Warranty.

OTHER THAN AS HEREIN EXPRESSLY SET
FORTH, THERE ARE NO WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, WITH­OUT LIMITATION, THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ANY SUCH WARRAN­TIES OTHERWISE IMPOSED BY LAW BEING
HEREBY EXPRESSLY DISCLAIMED.

Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation
may not apply to you.

PLASMA AIR IS NOT AND SHALL UNDER NO
CIRCUMSTANCES BE LIABLE OR RESPONSIBLE
FOR ANY SPECIAL, INCIDENTAL OR CONSE­QUENTIAL DAMAGES, LOSSES, OR EXPENSES
ARISING FROM A CLAIMED OR ACTUAL
DEFECT IN ANY OF THE PRODUCTS PUR­CHASED UNDER THIS WARRANTY OR THE
INSTALLATION OR USE THEREOF OR FROM
ANY OTHER CAUSE WHATSOEVER, INCLUD­ING, BUT NOT LIMITED TO, LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF REVENUES AND
ANY OTHER ECONOMIC LOSS.

Some states do not allow the exclusion or limita­tion of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.

INSTALLATION,

OPERATION

& MAINTENANCE

MANUAL

PlasmaPURE 600

PLASMA AIR
35 MELROSE PLACE

STAMFORD, CT 06902

www.plasma-air.com/residential

phone [phone]

fax [phone]

www.plasma-air.com

[e-mail]

INTRODUCTION

The PlasmaPURE 600 is a brush-style
needlepoint ionizer producing positive and
negative oxygen ions that neutralize odors and
harmful pollutants. This unit is highly versatile
as it may be installed in a furnace, an air
handling unit, fan coil unit, PTAC, heat pump
or ductless split system. The unit is
self-contained in a potted ABS enclosure
which has molded tabs with mounting holes
for fan inlet mounting with screws or magnet.
Models are available to accept 12VDC,
24VAC, 120VAC and 230VAC without the use
of an external power supply.

MAGNET

BRUSH

AIR FLOW

FIGURE 1

BRUSH

MECHANICAL INSTALLATION

WARNING: Do not connect to power
before mechanical installation is
complete.

1. Mount unit downstream of the filter, for

best results avoid locations directly down­stream of the cooling coil or a humidifier.

2. Mount unit at or near the fan inlet ensuring

air stream flows over the two brushes
simultaneously. See figures 1& 2.

3. Attach magnet to the sheet metal fan

housing. If using the mounting holes, ensure
the screws are not too long to avoid
interference with fan.

4. The tips of the brushes should be 1" away

from any metallic or grounded object.

ELECTRICAL INSTALLATION

WARNING: Do not connect to power
before installation is complete. Always
disconnect power to the unit before
handling the ionizer.

1. All field wiring to be in accordance with

NEC and Authorities Having Jurisdiction
(AHJ).

2. Connect power to ionizer using appropriate

voltage per the following: See figure 3.
601=12VDC, 602=24VAC, 603=120VAC,
604=230VAC

3. For 120VAC and 230VAC models the

installer shall provide a grounding method
per the local AHJ.

4. For best results interlock ionizer with

fan powe r.

5. Keep power wires away from tips of

brushes.

6. Apply power to unit. Green light indicates

the ionizer is functioning properly.

OPERATION

1. When power is supplied to the ionizer, the

ionizer will be activated and will illuminate
the green ion indicator light.

2. The ionization unit is self balancing and

does not require any type of adjustment.

TROUBLESHOOTING

If the unit is not working, check the following:

1. The supply fan is running and that the green

light illuminates.

2. Check the power input connections to the

ionization unit. Verify all connections are
correct and tightened. Reconnect any loose
wires as necessary.

FIGURE 2

MOUNTING HOLES

OR USE MAGNET

PlasmaPURE 600 IONIZER

CONNECT

TO POWER

FAN INLET

IN LINE 500 mA
GLASS CARTRIDGE FUSE

FAN
DISCHARGE

FIGURE 3

PlasmaPURE

600 IONIZER

(BLACK AC/RED DC)

(WHITE AC/BLACK DC)

MOUNTING
HOLES

phone [phone]
fax [phone]

FUSE

CONNECT
TO POWER

www.plasma-air.com

[e-mail]