Plantronics Voyage Legend UC, BT300Bluetooth Quick Start Manual

Charge and Fit Headset

Three ways to charge your headset

Your new headset has enough power to p air and make a few calls before
charging is needed, though y ou may charge at any time.

1 Align snap-fit magnetic area s of headset and charging device.

2 Attach charging device to USB wall c harger or laptop for 90 minutes. LEDs

turn off once fully charged .

USB cable to PC or USB wall charger

Charge case to PC or USB wall charger

NOTE Your charge case has an internal batte ry and can fully recharge yo ur headset

twice while on the go befo re needing connection to a ch arge cable.

Charge stand to PC or USB wall charger

Fit your headset

Replace the eartip for a bet ter fit.

1 Push in ear tip and rotate to the left to unlock it .

2 Align new eartip into slot.

3 Push in eartip and rotate to the righ t to lock it into place.

To wear the headset on your other ear, rotat e the boom upwards then
twist it around so ear tip is on other side before lowerin g boom.

2

1

3

Connect PC and Call

Connect

1 Power headset on.

2 Insert Bluetooth USB adapter direc tly into your PC USB port. The LED

will flash and then turn solid blue to i ndicate the headset is connecte d
to the USB adapter. You will also hear “PC connec ted”. The LED remains
solid blue when not on an acti ve call.

NOTE Your Bluetooth USB adapter comes pre-p aired to your headset.

3 Load Plantronics Spokes sof tware by visiting plantronics.com/sof tware

and click on the download but ton.

NOTE Spokes software allow s you to customize your headset ’s behavior

through advanced sett ings and options.

4 Check your audio settings

Confirm the speaker and microph one settings for your PC sof tphone are
set to Plantronics BT30 0.

Windows 7

Go to Control Panel -> Sound-> Playbac k tab, and set the Plantronics
BT300 device as the Defau lt Communications Device. If you pla n to listen
to streaming audio set the Pl antronics BT300 device as the D efault Audio
Device as well. In the Playbac k tab, this is indicated by the green chec k
mark.

Go to Control Panel -> Sound-> Recordin g tab, and set the Plantronics
BT300 device as the Defau lt Communications Device.

Windows XP

Go to Control Panel -> Sounds and Audi o Devices, and in the Audio tab
set the Plantronics BT 300 as the default device for Sound Pla yback and
Sound Recording.

5 Place a call from your computer softphon e. During an active call, the

Bluetooth USB adapter will flash blue ..

To Re-pair your Bluetooth USB adapter

In the event that your headse t and Bluetooth USB adapter become
unpaired do the following:

1 Power headset on.

2 Remov e the USB adapter.

3 P ower on your headset then choos e:

• Tap the Voice button and say “Pair mode,” or

• Press and hold the Call button until you hear “Pairing”.

4 Insert Bluetooth USB ada pter directly into your PC USB por t. Once

successfully paired, LED s stop flashing red and blue and you hea r “PC
connected”.

Pair Mobile Phone and Call

Pair your mobile phone

1 Power on your headset then c hoose:

• Tap the Voice button and say “Pair mode,” or

• Press and hold the Call button until you hear “Pairing”. While the
headset LEDs are flashing red and b lue, activate Bluetooth® on y our
phone and set it to search for n ew devices.

2 While the headset LEDs are flash ing red and blue, activate Blueto oth®

on your phone and set it to sear ch for new devices.

3 Select “PLT_Legend”.

PLT_Legend

4 If prompted by your mobile phone fo r a passcode enter 0000. Once

successfully paired, LEDs s top flashing red and blue and you hear
“pairing successful”. Some ph ones may prompt you to allow access to
contacts to enable caller n ame announcement.

PLT_Legend

5 Make a test call from your mobile ph one.

6 End the call by pressing the call button . The call does not end when

you remove your headset .

Pair another phone

After pairing your headse t to your phone you may want to pair another
or new phone.

1 Power on your headset then c hoose:

• Tap the Voice button and say “Pair mode,” or

• Press and hold the Call button until you hear “Pairing”

2 While the headset LEDs are flash ing red and blue, activate Blueto oth®

on your phone and set it to sear ch for new devices.

3 Select “PLT_Legend.”

4 Once successfully paired, LED s stop flashing red and blue and you hear

“pairing successful.”

NOTE Some phones may prompt you to al low access to contacts to enabl e

caller name announcement.

QUICK START GUIDE

Voyager Legend UC
Bluetooth Headset

BT300
Bluetooth USB Adapter

Designed in Santa Cruz, California

Use and Reset Smart Sensors

™

Use sensors

Smart Sensors reac t when you put on or take off your heads et.

Putting on your headset w ill:

• Answer an incoming call

• Transfer an active call from your phone (Available only with
your mobile phone)

• Resume streaming audio

Taking off your headset will:

• Transfer an active call to your phone handset (Available only with

your mobile phone)

• Pause streaming audio

• Lock the Call button to prevent accidental calls

Try voice commands

Tap the Voice button wait for command reque st, then say a
command. For example, “ What can I say?” tells you the full list of
available commands.

Reset sensors

You may need to reset the sensor s if they are not working as expe cted.

Wearing the headset, tap t he Call button to test sensor s:

• Talk time voice alert means sensors are working

• A tone means sensors need to be reset

To reset the sensors, charg e your headset and place on a flat non­metallic surface for mor e than 10 seconds.

3

Please refer to the s eparate safet y instructio ns for important p roduct safet y
information prio r to installation o r use.

The B235 Wireless He adset System co nsists of a BT300 USB A dapter and a Voyage r
Legend Bluetooth headset.

87750-01 (11.12)

voice

21

Answer a call, choose:

• Put on the headset to answer
call, or

• Tap the Call button or

• Say “answer” after call is
announced. (Available only with
your mobile phone)

Reject a call, choose:

• Press Call button for
2 seconds, or

• Say “ignore” after call is
announced. (Available only with
your mobile phone)

End a call

Tap the Call button to end

current call.

Voice dial (mobile phone fea-

ture)

Press the Call button for 2

seconds, wait for phone prompt
and then tell the phone to dial
the name of a stored contact.

Mute the microphone

during a call

Tap the Mute button . You will

hear “mute on” confirmation.
An alert repeats every 15 min­utes as a reminder. Tap
the Mute button again to
open the microphone and hear
“mute off” confirmation.

Play or pause streaming audio

A 2-second press of the Play/

pause button will either
pause or resume playback of
streaming audio.

Call back last call

Double-tap the Call button .

(Available only with your mobile
phone)

Adjust the volume

Toggle the Volume button up

(+) or down (–) during a call or
while streaming audio.

4

NEED MORE HELP?

Technical support

plantronics.com/support

Online user guide

http://docs.plantronics.com/VoyagerLegendUC

Plantronics, Inc.

345 Encinal Street

Santa Cruz, CA 95060

United States

© 2012 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Plantronics Voyager Legend,
QuickPair, are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth® word mark and logos
are owned by the Bluetooth SIG, Inc. and any use of such marks by Plantronics, Inc. is under license. All other
trademarks are the property of their respective owners.

Patents Pending

Australia

Z302 N10687

Singapore Complies with
IDA Standards DA101760

Philippines

Voyager Legend
ESD - 1206509C

BT300
ESD - 1004955C

BC

FCC Regulatory Information

Declaration of Conformity

We Plantronics, 345 Encinal Street, Santa Cruz, California, 95060 USA [phone], declare under our sole responsibility
that the product BT300 complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

NOTE: Modifications not expressly approved by Plantronics, Inc. could void the user’s authority to operate the equipment.

Industry Canada Regulatory Information

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.

Exposure to RF Radiation

The internal wireless radio operates within the guidelines found in radio frequency safety standards and recommendations,
which reflect the consensus of the scientific community. Independent studies have shown that the internal wireless radio is
safe for use by consumers. Visit plantronics.com for more information.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Cet équipement est
conforme aux limites d'exposition de radiation IC énoncés pour un environnement non contrôlé.