Planex MZK-NAS01SG, MZK-NAS02SG User Manual

Download

Multi Media Network Attached Storage 1 Bay / Storage 2 Bay

MZK-NAS01SG / MZK-NAS02SG

Foreword

Explanation of the signals

In order to let you set up and use this product correctly, please pay attention when reading or

browsing the manual as you see these signals listed below.

Warning/ Danger

Users should read the explanation carefully and understand it completely, otherwise

users might be in danger or even be injured.

Caution/ Be Careful

Remind users to be careful when setting up the product and to avoid damaging the

product or its system programs.

Seeking for service or searching for an agent or a distributor

Thank you for purchasing products from Planex Communications Inc. If you have any

operational problems while conﬁguring or setting up the product, you may contact with our

Customer Service Department or ask the agent or the distributor from which you bought

the product for help. Moreover, during warranty, if you ﬁnd any defect or breakdown of the

product, you may bring the product, assembly, and its warranty card to our company or to

where you bought the product to ask for repair.

★Every product has different warranty period and contract; please refer to our

company for further information or consult the agent or the distributor.

Planex Communications Inc. Support Phone：+65-6338-1704 (Singapore)

+886-2-7705-6172/6173/6174 (Taiwan) Customer Service E-Mail：techsupport@planex.net

Trademarks:

To maintain compliance with FCC RF exposure compliance requirements, please avoid direct

contact to the transmitting antenna during transmitting.

Contents

Foreword

Chapter1

Introduction of MZK-NAS01SG/MZK-NAS02SG

. .1

1. Contents of Package . . . . . . . . . . . . . . . . . . .2

Chapter 2 Function Introduction and Quick Install Guide

. .3

1. Product Functions . . . . . . . . . . . . . . . . . . . . . .3

2. Installation Guide . . . . . . . . . . . . . . . . . . . . . .7

Chapter 3 Web Configuration and RAID . . . . . . . . . . . . . 17

1. WEB Configuration . . . . . . . . . . . . . . . . . . . . 17

2. Building RAID (For MZK-NAS02SG Only) . . . . 19

Chapter 4 Common Functions . . . . . . . . . . . . . . . . . . . .23

1. Adding Users . . . . . . . . . . . . . . . . . . . . . . . . .23

2. Adding Groups . . . . . . . . . . . . . . . . . . . . . . . 25

3. File Server . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4. BT Download . . . . . . . . . . . . . . . . . . . . . . . . . 33

5. WEB/FTP Download. . . . . . . . . . . . . . . . . . . . 37

Chapter 5 Detail Function . . . . . . . . . . . . . . . . . . . . . . . . 41

1. Language . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

2. Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

MZK-NAS01SG/MZK-NAS02SG

3. Basic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

3.1. Time Zone . . . . . . . . . . . . . . . . . . . . . . . . 43

3.2. Password. . . . . . . . . . . . . . . . . . . . . . . . . 44

4. Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

5. File/FTP Server . . . . . . . . . . . . . . . . . . . . . . . .46

5.1. Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

5.2. Groups . . . . . . . . . . . . . . . . . . . . . . . . . . 48

5.3. File Server . . . . . . . . . . . . . . . . . . . . . . . . 50

5.4. FTP Server . . . . . . . . . . . . . . . . . . . . . . . .55

6. BitTorrent . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

7. Web/FTP Download . . . . . . . . . . . . . . . . . . .64

8. iTunes Server . . . . . . . . . . . . . . . . . . . . . . . . .66

9. Media Server. . . . . . . . . . . . . . . . . . . . . . . . . 69

10. Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

10.1. Storage Tools (For MZK-NAS02SG) . . . . 71

10.2. Storage Status . . . . . . . . . . . . . . . . . . . 73

10.3. USB Copy . . . . . . . . . . . . . . . . . . . . . . . 73

10.4. Configuration Tools . . . . . . . . . . . . . . . 74

10.5. Firmware Update . . . . . . . . . . . . . . . . . 76

10.6. Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

MZK-NAS01SG/MZK-NAS02SG Contents

MZK-NAS01SG/MZK-NAS02SG

Introduction to MZK-NAS01SG / MZK-NAS02SG

Thank you for purchasing MZK-NAS01SG/MZK-NAS02SG Network

Attached Storage (NAS) server. This Storage device can let you share your

files with users all around your network easily. All you have to do is insert

your SATA hard disks into MZK-NAS01SG/MZK-NAS02SG, connect the

LAN port with a LAN cable (RJ45 connectors), some basic settings, and you’re ready to share your files on your LAN network. MZK-NAS01SG/

MZK-NAS02SG provide the perfect file sharing/storage solution for

medium size business or Small Office/Home Office (SOHO).

MZK-NAS01SG/MZK-NAS02SG have a built-in Web server, thus you can

access its settings through Web browsers, such as IE, Netscape, Firefox,

and so on. You can set up and configure the settings easily and completely

and enjoy the convenience instantly.

MZK-NAS01SG/MZK-NAS02SG have many features, which includes:

● Support two internal SATA hard disk drives (MZK-NAS02SG only)

● Provide two USB ports for USB mass storage devices connecting

● Sharing your files via FTP or Network Neighborhood

● Sharing your multimedia files to DLNA compliant media adapters, such

as Xbox 360 and Sony PS3

● Built-in iTunes Server allows you to share your music with all the users

on your local Network.

● Download functions allow you to download files through FTP, World

Wide Web (WWW), and BitTorrent.

● High file transfer rate (more than 100Mbps)

Chapter1 Introduction to MZK-NAS01SG/MZK-NAS02SG

MZK-NAS01SG/MZK-NAS02SG

1. Contents of Package

After purchasing MZK-NAS01SG/MZK-NAS02SG Network Attached

Storage (NAS) server form a distributor or an agency, please open the

package and check that all the components listed below are included. If

there is any item missing or damaged, please contact with the distributor or

the agency at once.

MZK-NAS01SG

● MZK-NAS01SG

● CD-ROM (User’s Manual)

● AC Adapter

● AC Power Cable

● Screw (x4)

● Rubber Foot (x4)　

● UTP cable

● Warranty Card

MZK-NAS02SG

● MZK-NAS02SG

● CD-ROM (User’s Manual)

● AC Adapter

● AC Power Cable

● Screw (x8)

● Rubber Foot (x4)　

● UTP cable

● Warranty Card

If plug the AC adapter which includes in the product package

into a socket with different voltage power supply, it will cause

damage and that is not included in warranty.

Chapter2 Function Introduction and Quick Install Guide

Function Introduction and Quick Install Guide

Front Panel

LED Status Meaning

Power On/Flashing

After turning MZK-NAS01SG/MZK-NAS02SG, the Power LED will be on. If MZK-NAS01SG/MZKNAS02SG is shutting down or restoring to the default settings, the Power LED will be ﬂashing.

LAN 1/2 On/Off

LAN LE D wi l l b e on wh en t he L AN p ort is connected, and will be off when the LAN port is disconnected.

USB 1 / 2 On/Flashing

When connecting with a USB storage device (with

FAT32, FAT16, and EXT2 format), the LED will be on.

The LED will be flashing when copying files from the USB device to MZK-NAS01SG/MZKNAS02SG.

HDD 1/2 On/Flashing

When internal SATA hard disk is connected and formatted by MZK-NAS01SG/MZK-NAS02SG, the HDD LED will be on accordingly.

● LEDs and Meanings:

1. Product Functions

MZK-NAS01SG MZK-NAS02SG

MZK-NAS01SG/MZK-NAS02SG

●Release Button:

The Release button has three functions: 1. Unplug the external USB

mass storage connected to the USB 1 port. 2. Shut down MZK-

NAS01SG/MZK-NAS02SG. 3. Reset the configuration of MZK-

NAS01SG/MZK-NAS02SG to factory default settings (when pressing

Copy button at the same time).

◆Unplug the external USB storage device: Press and hold Release

button for 2 seconds, MZK-NAS01SG/MZK-NAS02SG will beep

for 0.5 second to hint that your command is detected. Release the

Release button immediately, and unplug the external USB storage

device plugged in USB1 port safely. If you want to unplug the external

USB device connected to the USB 2 port, please doing so by using

MZK-NAS01SG/MZK-NAS02SG configuration webpage. (Tools ->

Storage Status -> Unplug)

◆Shut down MZK-NAS01SG/MZK-NAS02SG: Press and hold

Release button for more than 5 seconds to start shutting down the

storage server. Ignore the first short beeping sound. The Power

LED will keep flashing, and you will hear a long beeping sound.

When the Power LED goes off, MZK-NAS01SG/MZK-NAS02SG

are completely shut down. You can now switch off the power by

switching the Power switch on the back panel of MZK-NAS01SG

/MZK-NAS02SG.

◆Restore the configuration of MZK-NAS01SG/MZK-NAS02SG to

factory default settings: If you want to reset the configurations of

MZK-NAS01SG/MZK-NAS02SG to factory default settings, you

should press and hold BOTH the Release button and the Copy buttons

at the same time for more than 5 seconds until you hear a long beep.

The Power LED will keep flashing during the restore process. After the

restore is complete, MZK-NAS02SG will restart automatically.

Chapter2 Function Introduction and Quick Install Guide

●Copy Button:

The Copy button has two functions: 1. Copy the content of one external

USB storage device to another attached storage device. 2. Reset the

configuration of MZK-NAS01SG/MZK-NAS02SG to factory default

settings (when pressing Release button at the same time).

◆Copy USB mass storage device: Press and hold the Copy button

for 2 seconds, MZK-NAS01SG/MZK-NAS02SG will beep for 0.5

second to hint that your command is detected. Release the Copy

button immediately if you want to copy the content of one external

USB mass storage device to another attached storage device. During

the process of copy, the LED of corresponding USB port will flash

slowly. When the LED of corresponding USB port stops flashing and

is lit steady, the copy job is finished. If any error occurs during the

process of copy, the LED of corresponding USB port will flash very

fast. The default source storage is USB 1. You can change the source storage by USB Copy settings in MZK-NAS02SG’s Web user

interface.

◆Restore the configuration of MZK-NAS01SG/MZK-NAS02SG to

factory default settings: If you want to reset the configurations of

MZK-NAS01SG/MZK-NAS02SG to factory default settings, you

should press and hold BOTH the Release button and the Copy

buttons at the same time for more than 5 seconds until you hear a

long beep. The Power LED will keep flashing during the restore

process. After the restore is complete, MZK-NAS02SG will restart

automatically.

●USB 1: USB 1 port allows you to share your files stored in the USB

mass storage device plugged in.

MZK-NAS01SG/MZK-NAS02SG

Back Panel

Ports Function

USB 2

USB 2 port allows you to share your ﬁles stored in the USB mass storage device plugged in. Also, USB 2 ports allows you to format the attached USB storage device

LAN 1/2

Use standard LAN cables (RJ45 connectors) to connect MZKNAS01SG/MZK-NAS02SG with your hubs/switches, or one LAN port of your router, etc.

Plug the power cord into this port and the other side of the adaptor should be plugged into the socket.

Button Function Usage

Power

On/Off

Turning On/

Off MZK-

NAS01SG/

MZK-

NAS02SG

Please do not turn off the p ower while MZKNAS01SG/MZK-NAS02SG is running. This will cause data saving errors and MZK-NAS01SG/MZKNAS02SG may not be able to work properly. Before switching off the power, please press Release button for more than 5 seconds and shut down MZKNAS01SG/MZK-NAS02SG ﬁrst.

MZK-NAS01SG MZK-NAS02SG

Chapter2 Function Introduction and Quick Install Guide

2. Installation Guide

Please follow this step-by-step guide and install your MZK-NAS01SG/

MZK-NAS02SG.

1.Please push the button of the hard disk drawer in the back panel of

MZK-NAS01SG/MZK-NAS02SG, releasing the drawer lock.

2.Pull out the hard disk drawer gently.

MZK-NAS01SG/MZK-NAS02SG

3.Place your SATA hard disk on the hard disk drawer as shown in the

picture.

Note: When you put the SATA hard disk on the hard disk drawer,

make sure the screw holes of the hard disk match those of the

drawer.

4.Fix your SATA hard disk tightly in the hard disk drawer with the

screws provided in the MZK-NAS01SG/MZK-NAS02SG package.

Chapter2 Function Introduction and Quick Install Guide

5.After securing the SATA hard disk tightly to the hard disk drawer, slide

the drawer back to MZK-NAS01SG/MZK-NAS02SG gently as shown

in the picture.

6.Push the leverage of the hard disk drawer, sliding the drawer further

into MZK-NAS01SG/MZK-NAS02SG until you hear a slight “click ” sound.

Note: Please make sure the hard disk drawer is installed correctly as

shown in the picture.

MZK-NAS01SG/MZK-NAS02SG

7.Plu g in the RJ45 cor d to an y LA N port on th e ba ck pan el of

MZK-NAS01SG/MZK-NAS02SG.

8.Plug in the other side of the RJ45 cord to the LAN port of your PC or

router.

Chapter2 Function Introduction and Quick Install Guide

9. P l u g in t h e p o w e r ad a p t e r pr o v i d e d i n MZ K- N A S0 1S G /

MZK-NAS02SG package into the DC port, and the other side in the

power socket as shown in the picture.

Plug the AC Adapter which comes with MZK-NAS01SG/MZK-

NAS02SG in a different voltage power supply will cause damage

on MZK-NAS01SG/MZK-NAS02SG, and it is not included in

warranty.

MZK-NAS01SG/MZK-NAS02SG

10. Turning on MZK-NAS01SG/MZK-NAS02SG by pressing the Power

On/OFF switch in the back panel.

11. If your computer is having trouble connecting to MZK-NAS01SG/

MZK-NAS02SG and the configuration webpage isn’t displayed

properly, please follow the steps down below and configurate your

computer.

●Click “Start” button (it should be located at lower-left corner of your computer), and then click “Control Panel”.

Before turning your MZK-NAS01SG/MZK-NAS02SG on, make

sure that your MZK-NAS01SG/MZK-NAS02SG is connected to

the router properly. If you fail to do so, your computer may not be

able to connect to MZK-NAS01SG/MZK-NAS02SG.

Chapter2 Function Introduction and Quick Install Guide

●Double-click “Network and Internet Connections”, and then click “Network Connections”.

MZK-NAS01SG/MZK-NAS02SG

●Right click “Local Area Connection”, and select “Properties”, a “Local Area Connection Properties” window will appear.

Chapter2 Function Introduction and Quick Install Guide

●Choose the “General” page, click on “Internet Protocol (TCP/IP)”, and then click “Properties” down below.

MZK-NAS01SG/MZK-NAS02SG

●Please enter the IP address, Subnet mask, Default gateway, and

Preferred DNS server as shown below.

Note:the values of IP address, Subnet mask, Default gateway, and

Preferred DNS server shown here might not work on your

system. If this happens, please acquire these values from your

system administrator.

Chapter3 Web Configuration and RAID

Web Configuration and RAID

1. WEB Conguration

MZK-NAS01SG/MZK-NAS02SG has a built-in Web server, and you can configure MZK-NAS01SG/MZK-NAS02SG’s settings through this easy

to use configuration webpage. Please follow this guide and start and start

configuring your system.

1.Start Your Web Browser (IE, Firefox, or Netscape).

2.E n ter “http://192.168.1.100”, t he d efa ult IP Ad dres s of the

MZK-NAS01SG/MZK-NAS02SG Address box, and press “Enter”.

MZK-NAS01SG/MZK-NAS02SG

3. A pop-up will ask you to enter the User Name and Password to get into

the configuration Webpage. Please enter the default User Name “ Admin”, and default password “0000”.

4.You should be able to connect to MZK-NAS01SG/MZK-NAS02SG

configuration webpage now.

Chapter3 Web Configuration and RAID

2. Building RAID (For MZK-NAS02SG Only)

If you installed 2 SATA hard disks on your MZK-NAS02SG, you have to

format and partition these hard disks when you turn on MZK-NAS02SG

for the first time.

1.Start Your Web Browser (IE, Firefox, or Netscape).

MZK-NAS02SG supports two kinds of RAID: RAID 0 and RAID 1.

RAID 0 helps to you merge two hard disk drives together in striped way.

It simulates a big hard disk and the available space of the virtual big

hard disk drive is the sum of the two physical internal SATA hard disk

drives. RAID 0 only works when both internal SATA hard disk drives are

functioning normally. If any one of the two internal SATA hard disk drives

fails in RAID 0 mode, you will lose all the data and it is unrecoverable.

RAID 1 maintains two copies of your data in the two internal SATA

hard disk drives. Each disk drive keeps one copy. So RAID 1 still works

correctly if just only one of the two internal SATA hard disk drives fails.

Since RAID 1 keeps two copies of whole data, the disk space utilization

is only 1/2. RAID 1 simulates a stable hard disk drive and the available

space of the virtual stable hard disk drive is the size of the smaller physical

internal SATA hard disk drive if the sizes of the two internal SATA hard

disk drives are different (The additional space of the larger hard disk drive

is useless).

MZK-NAS01SG/MZK-NAS02SG

Please follow these steps and build your RAID.

1.Start the configuration page, click “Tools” on the left side of the menu, and then click “Storage Tools” on the upper-left.

2.Click “Enable”, choose the RAID mode you would like to apply, and then click “Apply” to enable the RAID function.

3.If you choose RAID 0, the system will ask you if you would like to keep

the old data of your original RAID 0 or create a new RAID.

Chapter3 Web Configuration and RAID

If you choose RAID 1, the system will ask you if you would like to keep

the data on either hard disk 1, hard disk 2, or delete all the data in both hard

disks and create a new RAID.

Click “OK” to proceed to the next step.

4.Click “OK”, and start formatting and partitioning your hard disk.

Note: Do not turn off the power of MZK-NAS02SG while formatting.

5.System will automatically jump back to the “Storage Tools” page, and

you should be able to check the partition you just added in the list down

below.

MZK-NAS01SG/MZK-NAS02SG

Chapter4 Common Functions

Common Functions

1. Adding Users

In order to share files in the storage device with other users, you have to

create accounts for these users. To do this, please follow the steps down

below.

1.Click “File/FTP Server” on the left side of the configuration page, click “Users” on the upper-left, and then click “Add” to enter the “Add a New User” page.

MZK-NAS01SG/MZK-NAS02SG

2.Entering the User Name you would like to add to the Users List. (Up to

20 alphanumeric characters, and are case sensitive)

3. Entering the description for that User.

4.Entering the passw o rd for that Use r. (Up to 20 a lphanumeric

characters, and are case sensitive)

5.Please enter the new password again for confirmation.

Chapter4 Common Functions

6.Click “Save”, and add the user to the Users List.

2. Adding Groups

You can cr e ate gro u ps an d add use r s into t hat grou p for ac cess

management purposes. To do so, please follow the next steps.

1.Click “File/FTP Server” on the left side of the configuration page, click “Groups” on the upper-left, and then click “Add” to enter the “Add a New Group” page.

2.Entering the Group Name you would like to add to the Groups List. (Up

to 12 alphanumeric characters, and are case sensitive)

MZK-NAS01SG/MZK-NAS02SG

3.Entering the description for the Group.

4.You can add users to the Group in this page as well. Click the select box

to add users, click “Save” to create the Group and add the selected

users to that Group.

Chapter4 Common Functions

3. File Server

You can share files stored in all attached storage devices via network

neighborhood. To do so, please fellow the following steps.

1.Click “File/FTP Server” on the left side of the configuration page, and click “File Server” on the upper-left to enter the “File Server”

page.

2.Entering the File Folder Name you would like to add to the Shared Folders List. (Up to 15 alphanumeric characters and underline “_”)

3.Entering the Workgroup Name you would like to add. (Up to 15

alphanumeric characters space and underline “_”)

MZK-NAS01SG/MZK-NAS02SG

4.Entering the description for the Shared Folder. (Up to 43 alphanumeric

characters)

5.Click “Add” and fill the information of the Add/Edit Shared Folder

page to add a new Shared Folders for File server.

6.Please enter the name of the Shared Folder you would like to create

here. (Up to 20 alphanumeric characters and underline “_”)

Chapter4 Common Functions

7. Click “Browse” button, a pop-up screen will show up.

MZK-NAS01SG/MZK-NAS02SG

8.Choose and click the hard disk icon on the upper-left side of the Path

Selecting screen, then choose and click the hard disk partition icon on the

right as shown in the picture below.

9.You can click “New Folder” button to create a new Shared Folder in your hard disk. A pop-up screen will show up. Enter the new folder’s name under the “Folder Name” field, and click “New” to create a new

folder.

Chapter4 Common Functions

10.Click “Submit” button and add the new Shared Folder’s Path.

11. Add/Delete Users from the Users/Groups field.

MZK-NAS01SG/MZK-NAS02SG

12. Click “Save” button to save the configurations you just made.

For more detail, please refer to chapter 5.

Chapter4 Common Functions

4. BT Download

BitTorrent downloading Manager allows you to download files without

leaving your computer on. To do so, please follow the steps down below.

1.Click “BitTorrent” on the left side of the configuration page.

2.Click “Add Torrent” button and enter “Add BT Torrent” page.

MZK-NAS01SG/MZK-NAS02SG

3.Please choose the location of your .torrent file. The source of the .torrent

file can be from Internet Address (a URL address which should

look like http://www.xxx.com/files/xxxx.torrent), PC (a .torrent file

you downloaded to your PC), or This File Server (a .torrent file you

downloaded to the file server).

4.If you choose Internet Address as your .torrent file source, please enter

the URL in the field down below.

5.If you choose PC or This File Server as your .torrent file source, please click “Browse” button and upload the .torrent file.

Chapter4 Common Functions

6.After assigning the .torrent file source, please assign a path for saving the

file you wish to download by clicking “Browsing” button on the field

down below.

7.Choose the path you would like to save your file, and click “Submit”

to save the configuration.

MZK-NAS01SG/MZK-NAS02SG

8.Please assign a priority level to this BT download item.

9.Click “Add” button and start downloading.

Chapter4 Common Functions

5. WEB/FTP Download

You can download large file from Web or FTP server without keeping

your computer turned on. To do so, please follow the steps down below.

1.Click “WEB/FTP Download” on the left side of the configuration

page.

2.Click “Enable”, and “Save” to enable the WEB/FTP Download

function.

3.Enter the URL of the file you wish to download from Web or FTP server.

MZK-NAS01SG/MZK-NAS02SG

4. Select a encoding used by the Web or FTP server.

5.Please specify the location you wish to save downloaded file. Click “ Browse” button to select the folder you wish to save the file.

Chapter4 Common Functions

6.If the Web or FTP server requires a User Name and a Password to log

in, please enter the User Name and the Password provided by the Web/

FTP server.

7.Click “Add” to add the download job to the download list and start

downloading.

MZK-NAS01SG/MZK-NAS02SG

Chapter 5 Detail Function

Detail Function

1. Language

You can change the language of the MZK-NS01SG/ MZK-NS02SG

configuration webpage.

Click the menu on the upper-right and select the language for the webpage.

MZK-NAS01SG/MZK-NAS02SG

2. Status

This page displays the general information and the status of the system.

Chapter 5 Detail Function

3. Basic

The Basic configuration webpage includes the Time Zone and Password

setup pages.

3.1. Time Zone

You can setup the time zone for MZK-NAS01SG/MZK-NAS02SG. This

will affect functions such as update time of files stored in this storage

server.

●

Set Time Zone : Scroll the list to choose the time zone for the system.

●

Time Server Address : You can enter the Internet address of an

NTP(Network Time Protocol) Server for your system to synchronize

with.

●Daylight Saving : Click the check box to enable the Daylight Saving

function. Select the period in which you wish to start using daylight

saving.

●Set System Date and Time : If your network is not connected to the

Internet, the storage server will have no chance to get correct time from

the time server. In this case, you can manually assign current time here.

●Apply：Click this button and save the changes you made.

●Cancel：Click “Cancel” to exit the current configuration page.

MZK-NAS01SG/MZK-NAS02SG

3.2. Password

You can change the password required to log into MZK-NAS01SG/MZKNAS02SG’s configuration webpage. By default, the password is “0000” . For your system’s safety, please change the password as soon as possible.

Password can contain up to 12 alphanumeric characters, and are case

sensitive.

●C urrent Passw ord：En ter yo ur cur rent p asswo rd. (Up to 12

alphanumeric characters, and are case sensitive)

●New Password：Enter the new password for MZK-NAS01SG/

MZK-NAS02SG. (Up to 12 alphanumeric characters, and are case

sensitive)

●Confirmed Password：Please enter the new password again for

confirmation.

●Apply

Click this button and save the changes you made.

●Cancel

Click “Cancel” to exit the current configuration page.

Chapter 5 Detail Function

4. Network

The Network configurations webpage includes the IP address and DNS

settings.

●

IP Address Settings:

◆

Obtain an IP address automatically : If you have a live DHCP server

in your network and wish MZK-NAS01SG/MZK-NAS02SG get IP address from your DHCP server, please select “Obtain an IP address

automatically”.

◆

Use the following IP address : Select this and assign IP address

manually. Please enter the IP Address, Subnet Mask, and Gateway

Address (Normally, the Gateway address should be the IP address

of the router that connects your network to the Internet) addresses

accordingly.

●

DNS Address Settings:

◆

First/Second/Third DNS Address : Enter the DNS Server’s address.

You can enter the second and the third DNS address as well. However,

this is optional and you may leave it blank.

●

Apply：Click this button and save the changes you made.

●

Cancel：Click “Cancel” to exit the current configuration page.

MZK-NAS01SG/MZK-NAS02SG

5. File/FTP Server

The File/FTP server configuration webpage includes Users, Groups, File

Server and FTP Server setup pages.

5.1. Users

You can add/edit users for your File/FTP server on this page.

●

Add : Click “Add” and fill the information of the Edit a User page to

add a new user for File/FTP server.

●

Edit : Select any user in Users list and click “Edit” to modify her/his

profile.

●

Delete Selected : Click “Delete Selected” to delete the selected

users in Users list.

●

Delete All : Click“Delete All”to delete all the users in Users list.

●

Reset : Click “Reset” to reset selection in Users list.

Chapter 5 Detail Function

●

User Name : Entering the User Name you would like to add to the Users

List. (Up to 20 alphanumeric characters, and are case sensitive)

●

Description : Entering the description for the User.

●

Pa ss wo rd : Ent er in g th e pa ss wo rd for th a t Use r. (Up to 20

alphanumeric characters, and are case sensitive)

●

Confirm Pass word : Please en t er the new pass w ord again for

confirmation.

●

Save : Save the User to the Users List.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

●

Cancel : Click “Cancel” to exit the current configuration page.

MZK-NAS01SG/MZK-NAS02SG

5.2. Groups

You can add/edit users for your File/FTP server on this page.

●

Add : Click “Add” and fill the information of the Edit a Group page to

add a new Group for File/FTP server.

●

Edit : Select any group in Groups list and click “Edit” to modify its

profile.

●

Delete Selected : Click “Delete Selected” to delete the selected

groups in Groups List.

●

Delete All : Click “Delete All” to delete all the groups in Groups list.

●

Reset : Click “Reset” to reset selection in Groups list.

Chapter 5 Detail Function

●

Group Name : Entering the Group Name you would like to add to the

Groups List. (Up to 12 alphanumeric characters, and are case

sensitive)

●

Description : Entering the description for the Group.

●

Select Authorized Users : Please check the select box to add users to the

new Group you just created.

●

Save : Save the Group to the Groups List.

●

Select All : Click “Select All” to select all the users in the list.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

●

Cancel : Click “Cancel” to exit the current configuration page.

MZK-NAS01SG/MZK-NAS02SG

5.3. File Server

MZK-NAS01SG/MZK-NAS02SG support CIFS (Samba) protocol, and

you can share files stored in all attached storage devices via network

neighborhood. You can assign the file server name, shared folders and

folder sharing policies.

●

Name : Entering the File Folder Name you would like to add to the

Shared Folders List. (Up to 15 alphanumeric characters and underline

“_”)

●

Group : Entering the Workgroup Name you would like to add. (Up to 15

alphanumeric characters, space and underline “_”)

●

Description : Entering the description for the Shared Folder. (Up to 43

alphanumeric characters)

●

Save : Save the Folder to the Shared Folders List.

●

Cancel : Click “Cancel” to exit the current configuration page.

Chapter 5 Detail Function

●

Add : Click “Add” and fill the information of the Add/Edit Shared

Folder page to add a new Shared Folders for File server.

●

Edit : Select any Shared Folders in Folder Name list and click “Edit”

to modify its profile.

●

Delete Selected : Click “Delete Selected” to delete the selected

Shared Folders in Folder Name List.

●

Delete All : Click “Delete All” to delete all the Shared Folders in

Folder Name list.

●

Reset: Click “Reset” to reset selection in Folder Name list.

●

New Storage Default Sharing Policy : This sharing policy will apply to

all the Shared Folders created afterward. There are three different

policies you can choose to apply:

◆

Read & Write : Users can both read and write files in the Shared

Folders.

◆

Read Only : Users can only read files in the Shared Folders.

◆

Not to Share: Users can neither read nor write files in the Shared

Folders.

●

Save: Save the configurations you made.

●

Default : Click “Default” to erase all the changes you made and set all

configuration values to default value.

Add/Edit Shared Folder:

MZK-NAS01SG/MZK-NAS02SG

●

Folder Name : Please enter the name of the Shared Folder you would

like to create here. (Up to 20 alphanumeric characters and underline

“_”)

●

Shared Folder’s Path : Click “Browse” button, a pop-up screen will

show up. You can add the Shared Folder’s Path here. Please follow the steps below and add a new Shared Folder’s Path:

1.Choose and click the hard disk icon on the upper-left side of the Path

Selecting screen, then choose and click the hard disk partition icon on the

right as shown in the picture below.

Chapter 5 Detail Function

2.You can click “New Folder” button to create a new Shared Folder in your hard disk. A pop-up screen will show up. Enter the new folder’s name under the “Folder Name” field, and click “New” to create a new

folder.

3.Click “Submit” button and add the new Shared Folder’s Path.

MZK-NAS01SG/MZK-NAS02SG

●

Anonymous : Click the check box and enable the “Anonymous

Sharing” function, allowing all users on the network log on to MZK-

NAS02SG anonymously.

●

User’s Groups : You can add or delete users/groups that are allowed to

access the specific Shared Folder. Choose the users/groups in the left field (“System Users/Groups”), and click “Add” or “Add All” to add the selected or all user/group to the right field (“Share Users/ Groups”). You can also click “Delete” or “Delete All” buttons to delete users or groups in the right field (“Share Users/Groups”).

●

Authority : You can choose an access policy for this Shared Folder. You

can choose “Read Only” (so the users/groups can only read files in the Shared Folders) or “Read & Write” (so the users/groups can both

read and write files in the Shared Folders).

●

Description : Entering the description for the Shared Folder.

●

Save : Save the configurations you made.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

●

Cancel: Click “Cancel” to exit the current configuration page.

Chapter 5 Detail Function

5.4. FTP Server

This storage server supports FTP protocol, which lets you share files stored

in all attached storage devices to both your network and Internet. In order

to do so, you must have Internet access and your router must have the

correct port forwarding settings.

●

Add : Click “Add” and fill the information of the Add/Edit FTP

Folder page to add a new FTP Folder for FTP server.

●

Edit: Select any Users in User Name list and click “Edit” to modify

its profile.

●

Delete Selected : Click “Delete Selected” to delete the selected User

in the List.

●

Delete All : Click “Delete All” to delete all the Users in the list.

●

Reset : Click “Reset” to reset selection in the list.

●

Advanced Settings :

◆

Max Users : Set the maximum concurrent users for the FTP server.

◆

Idle Time : Set the time that FTP server will wait before disconnecting

a FTP client when it is inactive.

◆

FTP Client Language (Encoding) : Select a language (or encoding)

used by the FTP clients.

●

Save : Save the configurations you made.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

MZK-NAS01SG/MZK-NAS02SG

Add/Edit FTP Folder:

●

User : Scroll down and choose a User who is allowed to access the FTP

Folder, or you can choose “anonymous” and allow everyone to access

this folder.

●

Shared Folder’s Path : Click “Browse” button, a pop-up screen will

show up. You can add the Shared Folder’s Path here. Please follow the steps below and add a new Shared Folder’s Path:

1.Choose and click the hard disk icon on the upper-left side of the Path

Selecting screen, then choose and click the hard disk partition icon on the

right as shown in the picture below.

Chapter 5 Detail Function

folder.

MZK-NAS01SG/MZK-NAS02SG

3.Click “Submit” button and add the new Shared Folder’s Path.

●

Authority : You can choose an access policy for this Shared Folder. You

can choose “Read Only” (so the users/groups can only read files in the Shared Folders) or “Read & Write” (so the users/groups can both

read and write files in the Shared Folders).

●

Save : Save the configurations you made.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

●

Cancel : Click “Cancel” to exit the current configuration page.

Chapter 5 Detail Function

6. BitTorrent

This storage server supports BT (stands for BitTorrent) peer-to-peer file

download function. You can download files via BitTorrent protocol,

without turning your computer on. You can also check all downloading

process on this page. Before downloading, please be sure that this storage

server has enough remaining storage space.

●

BT Download Function : You can enable or disable BT Download

Function here.

●

Max Concurrent Connection Number : You can input the maximum

BT download connection here; valid range is from 1 to 50. You can

download more files at the same time with higher connection number

you input here, but it will consume more bandwidth.

●

Save : Save the configurations you made.

●

Cancel : Click “Cancel” to exit the current configuration page.

●

BT Download List Table : You can click “Add Torrent” button

to add a new torrent (files with .torrent extension) file and start BT

Download. To add a new torrent, please follow the steps below:

MZK-NAS01SG/MZK-NAS02SG

1.Click “Add Torrent” button and enter “Add BT Torrent” page.

2.Please choose the location of your .torrent file. The source of the .torrent

file can be from Internet Address (a URL address which should

look like http://www.xxx.com/files/xxxx.torrent), PC (a .torrent file

you downloaded to your PC), or This File Server (a .torrent file you

downloaded to the file server).

3.If you choose Internet Address as your .torrent file source, please enter

the URL in the field down below.

Chapter 5 Detail Function

4.If you choose PC or This File Server as your .torrent file source, please click “Browse” button and upload the .torrent file.

5.After assigning the .torrent file source, please assign a path for saving the file you wish to download by clicking “Browsing” button on the field

down below.

MZK-NAS01SG/MZK-NAS02SG

6.Choose the path you would like to save your file, and click “Submit”

to save the configuration.

7.Please assign a priority level to this BT download item.

8.Click “Add” button and start downloading.

Chapter 5 Detail Function

●

Detail : Click this button to show the detail information for the

BitTorrent download file.

●

Pause : Click this button and pause downloading the selected file.

●

Resume : Click this button and resume downloading the selected file.

●

Remove All : Click this button and remove all the downloading files.

●

Remove Selected : Click this button and remove all the selected

downloading files.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

MZK-NAS01SG/MZK-NAS02SG

7. Web/FTP Download

This storage server supports downloading file from Web and FTP server, so

you can download large file from Web or FTP server without keeping your

computer turned on.

●

Web/FTP Download : Click “Enable” to enable the Web/FTP

Download function, click “Disable” to disable this function.

●

Save : Save the configurations you made.

●

Cancel : Click “Cancel” to exit the current configuration page.

●

Internet Address : Please enter the URL of the file you wish to

download from Web or FTP server.

●

URL Encoding : Select a encoding used by the Web or FTP server.

●

Save as : Please specify the location you wish to save downloaded file.

Click “Browse” button to select the folder you wish to save the file.

●

User Name/Password : These fields are optional. If the Web or FTP

server requires a User Name and a Password to log in, please enter the

User Name and the Password provided by the Web/FTP server.

●

Add : Click this button to add the download job to the download list and

start downloading.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

Chapter 5 Detail Function

●

Refresh : Click this button to update the latest status of the Download

Information Table.

●

Pause : Click this button and pause downloading the selected file.

●

Resume : Click this button and resume downloading the selected file.

●

Remove Selected : Click this button and remove all the selected

downloading files.

●

Remove All : Click this button and remove all the downloading files.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

MZK-NAS01SG/MZK-NAS02SG

8. iTunes Server

iTunes is a popular and powerful multimedia player which supports

streaming media. If you have media files supported by iTunes, you can

share these files by iTunes Server to other computers on your network.

●

iTunes Server : You can enable iTunes Server function by clicking “

Enable” or disable iTunes Server function by clicking “Disable”.

●

Save : Save the configurations you made.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

●

Server name : Please assign a name to iTunes server. All iTunes clients

will need this name to locate this iTunes server. The length of a valid

server name is from 4 to 20 characters and case sensitive.

●

Media folder : Please specify the folder where the media files are stored,

and all media files inside the folder you specified here will be shared to

all iTunes clients.

●

Save : Save the configurations you made.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

Chapter 5 Detail Function

●

Advanced Setting : Click this button to modify advanced settings for

this iTunes server.

◆

Protect by password : Scroll down the menu to enable iTunes Server

protection, all clients will have to enter the password to connect to the

iTunes Server.

◆

Password : Entering the password for your iTunes Server. (Up to 20

alphanumeric characters, space, “*”, and “_”. Passwords are

case sensitive)

◆

Confirm Password : Please enter the new password again for

confirmation.

◆

Rescan Interval : Please specify the time interval in second between

two iTunes server scans. The iTunes server periodically scan media

folder for newly added files. The valid rescan interval is from 1 to 300 seconds. You can also click “Rescan” button to start a scan

immediately. The required scan time varies depend on the number of media files. It may take several minutes to finish. It’s recommended

to use default value (300) to prevent iTunes server from rescanning

too frequently. A short rescan interval will make iTunes server respond

slower.

◆

Process m3u : If the folder where media files are located includes any

m3u (playlist) files, iTunes server will read it and generate proper

playlist for iTunes clients.

◆

Playlist : If you have a playlist file, you can upload it from PC or select

if from an attached storage device.

MZK-NAS01SG/MZK-NAS02SG

◆

Back : Click this button to go back to the last page.

◆

Save : Save the configurations you made.

◆

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

●

iTunes Server Status : This field shows the current status of your iTunes

Server.

●

iTunes User Status : This field shows the current status of the clients that

are connected to your iTunes Server.

●

Refresh : Click this button to update the latest status.

Chapter 5 Detail Function

9. Media Server

The media server function allows you to share your media files to DLNA

compliant media adapters and players through network.

●

Media Server : You can enable Media Server function by clicking “

Enable” or disable Media Server function by clicking “Disable”.

●

Save : Save the configurations you made.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

●

Server Name : Please specify the name of media player here. Media

players need this name to locate this media server.

●

Rescan Interval : Please specify the time interval in second between two

media server scans. The media server periodically scan media folder for

newly added files. The valid rescan interval is from 1 to 300 seconds. You can also click “Rescan” button to start a scan immediately. The

required scan time varies depend on the number of media files. It may take several minutes to finish. It’s recommended to use default value

(300) to prevent media server from rescanning too frequently. A short

rescan interval will make media server respond slower.

●

Save: Save the configurations you made.

●

Cancel : Click “Cancel” to exit the current configuration page.

MZK-NAS01SG/MZK-NAS02SG

●

Add : Click this button to add a new folder to store shared media files.

●

Remove Selected : Click this button and remove all the selected folders.

●

Remove All : Click this button and remove all the folders.

●

Reset : If there is anything wrong with the settings you made, you can

click “Reset” to configure the page again.

Chapter 5 Detail Function

10. Tools

This page provides various management tools, including Storage Tools,

Storage Status, USB Copy, Configuration Tools, Firmware Upgrade

and Reset.

10.1. Storage Tools (For MZK-NAS02SG)

You can use the Storage Tools to manage the partition and format of the

attached storage devices. It also allows you to build RAID 0 or RAID1 if

you have two internal SATA hard disk drives installed.