Page 1
User’s Manual
For
Bluetooth Mini Headset Plus
BT-03HS
Page 2
TABLE OF CONTENTS
Introduction.....................................................................................................................................3
Introduction to Bluetooth Wireless Technology........................................................................3
Bluetooth Mini Headset Plus BT-03HS ....................................................................................3
Package Contents......................................................................................................................3
Getting Start....................................................................................................................................4
Charging Battery.......................................................................................................................4
Check the Headset Buttons.......................................................................................................4
Turning On/Off Headset............................................................................................................4
Pairing Headset.........................................................................................................................5
Making Calls.............................................................................................................................5
Answering/Ending Calls...........................................................................................................5
Transfer/Switch Calls................................................................................................................6
Mute..........................................................................................................................................6
Connecting with PC or PDA.....................................................................................................6
Low Battery ..............................................................................................................................6
Important Information...................................................................................................................6
Troubleshooting........................................................................................................................6
Product Care..............................................................................................................................7
Children.....................................................................................................................................7
Travel Charger...........................................................................................................................7
Battery Information...................................................................................................................8
About Pairing............................................................................................................................8
FAQ ..................................................................................................................................................8
FCC Safety Statements.................................................................................................................11
CE Statements...............................................................................................................................11
2
Page 3
Introduction
Introduction to Bluetooth Wireless Technology
Bluetooth is a short range wireless communication technology. It allows wireless connections
between Bluetooth devices such as cellular phone, personal digital assistant (PDA), desktop
and notebook computer, input-output devices (mouse, keyboard, or printer), and home
appliances. Bluetooth refers to a worldwide standard designed to operate in the internationally
recognized ISM (Industrial Scientific and Medical) frequency band. Within the ISM band
(2.4Ghz – 2.48Ghz) Bluetooth transmissions hop between 79 separate frequencies 1,600
times every second, and with a communication range of about 10 meters (class II).
Bluetooth Mini Headset Plus BT-03HS
The Bluetooth Mini Headset Plus BT-03HS is a Bluetooth device developed with the latest
Bluetooth technology, which can connect to other Bluetooth devices such as mobile phone,
desktop or notebook computer, PDA (with audio gateway profile supported) wirelessly within a
range of 10 meters.
Package Contents
- Bluetooth Mini Headset Plus BT-03HS
- Travel Charger 100/240V
- Carry Bag
- Necklace and Hook
- Earplug Sponges
- CD-ROM (User’s Manual)
- Quick Installation Guide
3
Page 4
Getting St art
Charging Battery
The Headset comes with an embedded rechargeable battery. For first time use, it takes about
4 hours to fully charge the battery. Afterward, it takes about 2 hours to fully charge. With
battery fully charged, the talk time is up to 2 to 4.5 max hours, and the stand-by time will be up
to 100 hours max.
1. Connect Travel Charger with AC power; the green indicator of charger will light up.
2. Connect the Charger, Nokia DC Jack Connector and Headset as picture shown above,
both red and green indicators of Connector will light up.
3. When the battery is full charged, the red indicator of Connector will be off.
Check the Headset Buttons
- S1 Button: Power on/off, Answer calls, Volume up (increase Volume), Pairing
- S2 Button: End calls, Volume down (decrease Volume)
Turning On/Off Headset
1. To turn on the Headset, press and hold S1 button for 3 seconds. You will hear two short
high tones and the blue indicator of Headset flashes.
2. To turn off the Headset, press and hold S1 button for 3 seconds. You will hear two low
4
Page 5
tones and the red indicator flashes quickly. Then the Headset is powered off.
3. The red indicator of Headset will flash slowly when battery low.
Pairing Headset
You are required to pair the Headset with your mobile phone or other devices before using it.
Step 1: The Headset must be powered off before initiating pairing. To initiate pairing, press and
hold S1 button for 5 seconds until the blue and red indicators of Headset are flashing
alternatively. If you are wearing the Headset during the pairing process, you will hear
two short high tones when the Headset is ready for pairing.
Step 2: Initiate pairing process of your mobile phone. Refer to the manual of mobile phone for
detail process. You will see a new item “BT Headset-F” added in your Bluetooth device
list after searching process.
Step 3: You will be asked to enter pin-code to complete pairing, enter 1234 and confirm it. (Note:
The 1234 is default pin-code pre-stored in Headset.)
The red indicator of Headset will turn off and the blue indicator will flash slowly after pairing
completed successfully.
Note:
1. If the Headset is not in pairing m ode, your mobile phon e won't find the Headset. Please set
the Headset on pairing mode
before letting your mobile phone search for the Headset.
2.
If no pairing is possible for a period of time (approx. two minutes), the Headset will
automatically power off, and so the previous pairing (if any) is revoked. You may need to
repeat steps 1 to 3 until pairing succeeds
Making Calls
You are able to use the Headset to make calls when it is paired successfully with your mobile
phone.
1. Using voice dialing – Press S1 button, waiting for a beep and say the name of the person
you want to call. Press S1 button again to cancel voice dialing.
2. Using phone keys – Dial the number on the mobile phone as you usually do. Once the
call has been set up, the voice will be transmitted to Headset automatically.
3. Redial – Press and hold S2 button for 3 seconds to redial the last number you called.
Answering/Ending Calls
1. When the Headset is powered on and the mobile phone rings, you will hear a musical tone
and the blue indicator will change to be quick flashing. Press S1 button to answer the call.
2. Press and hold S2 button for 3 seconds to reject the call.
3. If the Headset is powered off, press and hold S1 button for 3 seconds to turn it on and
5
Page 6
answer the call.
4. Adjust Headset volume by pressing S1 button for volume up and pressing S2 button for
volume down.
5. End calls by pressing and holding S2 button for 3 seconds or do nothing.
Note:
Due to the different design of some mobile phones, an auto-disconnect may happen even
when the Headset is powered on. In that case, the Headset won't ring when there is an
incoming call. Press S1 button for 1 sec. to reconnect the Headset with mobile phone for an
incoming call.
Transfer/Switch Calls
1. Press and hold S1 button for 3 seconds to transfer the call to mobile phone while talking
on the Headset. If you want to transfer the call back to Headset, press S1 button again.
2. Press and hold S2 button for 3 seconds to switch to second call if a second call is coming
into while talking on a call. This function only works under your mobile phone service
provider provides such service.
Mute
Press both S1 and S2 buttons in the same time for a Mute function. Press both S1 or S2
buttons in the same time again to disable the Mute function.
Connecting with PC or PDA
You are allowed to connect the Headset with a Bluetooth enabled PC or PDA that is with Audio
Gateway
Profiles supported. Please refer to the user manual of your Bluetooth enabled PC or PDA for a
setup information.
Low Battery
When the red indicator starts to flash, it indicates that the Headset is running low on battery.
Charge the Headset for 2 hours until the red indicator turns off.
Important Information
Troubleshooting
1. The red LED indicator flashes.
It indicates that the Headset is running low on battery. Charge the
Headset for 2 hours until the red LED indicator turns off.
6
Page 7
2. The Headset cannot be activated after being charged for 20 minutes.
To activate the Headset, it needs to charge the battery at least for 40 minutes.
However, it is highly recommended to fully charge the battery before use.
3. No indication of charging is shown.
For the Headset battery that is empty, or has not been used for a long time,
it may take a couple of minutes for the Headset indicator to show charging status
with a steady red light.
4. No sound contact between Headset and other d evices.
- Make sure that the two devices have been paired.
- Make sure that the Headset is turned on.
- Make su re that the two devices are within a working range.
- Make sure that your Mobile Phone is within signal strength.
- Some Bluetooth mobile phones can support only one Bluetooth Headset.
Disconnection may happen when there is more than one Headset paired with your mobile
phone.
Product Care
- Use of non-original accessories may result in performance deterioration, injury, products’
damage, electronic shock, and warranty termination.
- Attempt to disassemble your Headset may damage it, and the warranty will be void.
- Do not put the Headset in a dusty place.
- Use only a clean soft cloth to clean your Headset.
- When the Headset is not in use, always keep it in its case.
- Do not allow children to play with your Headset, as they may injure themselves and
damage the Headset as well.
- Do not place the Headset in an extremely hot or cold temperature, if the Headset will not
be used for a while.
Children
Do not allow children to play with your Headset, as the small parts may cause a choking
hazard.
Travel Charger
- The charger is designed for indoor use only. Do not use it for outdoors.
- The charger must be connected to the designated power sources as ma rked.
- When removing the charger from an outlet, never pull the charger cord, as it may damage
the charger.
7
Page 8
Battery Information
- New batteries
- For first time use, plug the adapter into the Headset and charge it at least 4 hours
until the red indicator turns off.
- Battery care
- Only qualified Service Centers are authorized to remove or replace the battery.
- The rechargeable battery has a long service life if treated with care.
- The battery can only be charged in a temperature range of –10 C to 45 C.
- Use the battery in room temperature for maximum battery capacity.
- The battery capacity may be reduced if operating in a cold environment.
- The Headset has to be recharged every two months, when it is not in use during a
long time.
About Pairing
What is Pairing?
Pairing is a process of associating Bluetooth devices with each other. It will establish a
permanent security link between the devices and enable quick access to the services provid ed
without the need to enter passkeys.
Bluetooth Passkey
Each mini headset has a default passkey 1234 for pairing, which is stored in its internal
memory. You are usually required to enter the passkey 1234 in a pairing process with a
Bluetooth mobile phone or other devices; however it depends on the kind of Bluetooth device
that the headset is connected to. Please refer to the users’ manual of the devices for the
specific operation.
Paired devices remain paired even when:
- One of the devices is not powered on.
- A service connectio n is interrupted or the service stopped.
- One or both devices are rebooted.
FAQ
1. Why doesn't the Headset work with my mobile phone after the Headset has been fully
charged and switched on?
A: You have to activate the Bluetooth function of your mobile phone first and pair it with the
8
Page 9
Headset.
2. Does the Headset work with all types of mobile phones?
A: No. It works only with Bluetooth enabled mobile phones.
3. What is the operation distance between the Headset and a Bluetooth mobile phone?
A: The Headset has been tested and approved by BQB. It is fully compliant to Bluetooth v .
1.1, class II, Headset Profile. The maximum operation distance can be up to 10 meters;
however it will be affected and shortened by different circumstances and different brands
of mobile phones. Some mobile phones are with less operative distance.
4. When my mobile phone was searching for the Headset, why did several Bluetooth devices
appear on my mobile phone?
A: Most Bluetooth enabled mobile phones with Bluetooth function activated can search for
more than one Bluetooth device within operative range. The Headset will appear as "BT
Headset-F" or "Unknown Device" on your mobile phone after having been found by your
mobile phone.
5. Why can’t my mobile phone find the Headset?
A: If the Headset is not in pairing mode, your mobile phone won't find the Headset. Please
set the Headset into pairing mode before starting your mobile phone to search for the
Headset.
6. Do I need to pair the Headset with my mobile phone every time I use it?
A: No. Once the Pairing is set up between the two devices, they will remain paired even
when one or both devices are powered off.
7. Why is there a disturbance noise coming from the Headset?
A: The performance of the Headset will be affected by two factors
1) Whether your mobile phone is in a good signal area. If your mobile phone is in week
signal area, you won't hear clearly with the Headset.
2) Whether it is in the operative range.
8. What should I do when I can't hear very well with the Headset?
A: Adjust the sound volume on your mobile phone, or press the S1 button of the Headset
to increase volume, or check if your mobile phone is in a good signal area.
9. Why doesn’t the Headset work suddenly?
9
Page 10
A: 1) The headset may have run out of battery. When it is in low battery, a red LED will
start to flash.
2) Some Bluetooth mobile phones, which have a problem with the Bluetooth
implementation, will occasionally but not often, get into an Bluetooth shut-down status
in unpredictable circumstances. When this happens, please reset your mobile phone
by removing the battery. (It is not necessary to do the Pairing again.)
Make sure that your phone has the latest version of firmware loaded onto it. Please check
the website of your mobile phone for new firmware.
10. Why doesn’t the voice dialing function work with the Headset?
A: You may have to record your voice with the Headset to your mobile phone.
10
Page 11
FCC Safety Statements
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accep t any interferenc e received, including interference that may cause
undesired operation.
The radiated output power is far below the FCC Radio frequency exposure limits.
Nevertheless, this device should be used in such a manner that the potential for human
contact during normal operation is minimized.
Warning: Changes or modifications made to this equipment not expressly approved by the
manufacturer. May void the FCC authori zation to operate this equipment.
Important. Please note the following:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, whi ch can be determin ed by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
CE Statements
This device has bee tested and found to comply with the requirements set up
in the council directive on the approximation of the law of member states
relating to EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC and
R&TTE Directive 99/5/EC.
11
Page 12
Copyright and Trademark Notices
Products and brand names may be the trademarks or registe red trademarks of their respective
owners.
12
Loading...